橡胶老化检测标准橡胶老化-中析研究所检测

(CMA)

(CNAS)

(ISO)

(高新技术企业)

橡胶老化相关标准参考信息

GB/T 24135-2022 橡胶或塑料涂覆织物加速老化试验
简介：
信息：ICS：59.080.40 CCS：G42 发布：2022-10-12 实施：2022-10-12

KS M ISO 188-2014(2019) 橡胶硫化或热塑性 - 加速老化和耐热性试验
简介：
信息：ICS：83.060 CCS：发布：2014-10-14 实施：

ISO 6914-2008 硫化或热塑性橡胶.用拉伸中应力松弛测量法测定老化特性
简介：This International Standard describes three methods for the measurement of the change of stress in a testpiece at a given elongation for the purpose of determining the ageing characteristics of a rubber.- Method A is intended for measurement under continuous strain conditions. - Method B is the preferred method for measurement under intermittent strain conditions.In the case of both methods A and B, a stress relaxometer is used to record the stress at the temperature ofageing.-- Method C is an alternative to method B for measurement under intermittent strain conditions in which the test piece is removed from the ageing environment for measurement of the stress at standard laboratory temperature.The necessary calibration schedule for this type of measurement is given in Annex A.Measurements at a single elevated ageing temperature can be used for quality control purposes as a measureof heat-ageing resistance. Measurements at a number of temperatures can be used for research anddevelopment purposes to estimate long-term ageing characteristics in accordance with the proceduresdescribed in ISO 11346.No agreement between the three methods should be inferred. The method used will depend on the purpose ofthe test.
信息：ICS：83.060 CCS：G34 发布：2008-09 实施：

GB/T 3512-2014 硫化橡胶或热塑性橡胶热空气加速老化和耐热试验
简介：本标准规定了硫化橡胶或热塑性橡胶热空气加速老化和耐热试验方法。两种方法分别为:方法A:空气流速低的多单元式或柜式热空气老化箱,每小时换气3次~10次;方法B:使用风扇强制通风的柜式热空气老化箱,每小时换气3次~10次。
信息：ICS：83.060 CCS：G40 发布：2014-12-22 实施：2015-06-01

GOST 12.4.262-2014 职业安全标准体系. 带有橡胶或塑料涂覆植物的个人防护设备用材料. 加速老化试验方法
简介：
信息：ICS：59.080.40 CCS：发布：2014 实施：2015-12-01

ISO 6914:2008 硫化橡胶或热塑性橡胶.通过测量拉伸应力松弛测定老化特性
简介：
信息：ICS：83.060 CCS：发布：2008-08-28 实施：

GB/T 24135-2009 橡胶或塑料涂覆织物.加速老化试验
简介：本标准规定了四种评价涂覆织物耐加速老化性能的试验方法。
信息：ICS：59.080.40 CCS：G42;W59 发布：2009-06-15 实施：2010-02-01

BS ISO 6914-2013 硫化或热塑性橡胶.用拉伸中应力松弛测量法测定老化特性
简介：
信息：ICS：83.060 CCS：G35 发布：2013-12-31 实施：2013-12-31

KS M 6570-2008 橡胶用防老化剂
简介：이 규격은 고무용 배합제로 사용되는 노화방지제의 물리적, 화학적 특성의 시험방법에 대하여
信息：ICS：83.040.30 CCS：G35 发布：2008-05-28 实施：2008-05-28

GB/T 11206-2009 橡胶老化试验.表面龟裂法
简介：警告：使用本标准的人员应有正规实验室工作的实践经验。本标准并未指出所有可能的安全问题。使用者有责任采取适当的安全和健康措施，并保证符合国家有关规定条件。本标准规定了橡胶试样在静态应变状态下老化时表面发生龟裂的试验方法和评价方法。本标准适用于橡胶在静态拉伸或弯曲状态下置于大气环境下或含臭氧介质中进行的老化试验。本标准不适用于曝露在由于放电而产生高浓度臭氧的环境下的电绝缘材料或橡胶部件；也不适用于硬质橡胶。
信息：ICS：83.060 CCS：G40 发布：2009-04-24 实施：2009-12-01

BS ISO 6914-2013 硫化或热塑性橡胶.用拉伸中应力松弛测量法测定老化特性
简介：
信息：ICS：83.060 CCS：G35 发布：2013-12-31 实施：2013-12-31

GB/T 14522-2008 机械工业产品用塑料、涂料、橡胶材料人工气候老化试验方法.荧光紫外灯
简介：本标准规定了机械工业产品用塑料、涂料、橡胶材料的人工气候老化试验方法之一——荧光紫外灯暴露试验方法。本标准适用于塑料、涂料、橡胶等材料的耐候性比较和筛选试验。
信息：ICS：19.040 CCS：A21 发布：2008-06-16 实施：2009-03-01

ISO 6914-2013 硫化橡胶或热塑性橡胶. 老化性能的测定 (拉伸应力松弛试验)
简介：This International Standard describes three methods for the measurement of the change of stress in a test piece at a given elongation for the purpose of determining the ageing characteristics of a rubber.
信息：ICS：83.060 CCS：G40 发布：2013-12 实施：

KS M ISO 1419-2008 橡胶或塑料涂层织物.加速老化试验
简介：이 표준은 코팅된 원단의 촉진 노화에 의한 내열화성을 평가하기 위한 네 가지 방법을 규정한
信息：ICS：83.140 CCS：W59 发布：2008-04-04 实施：2008-04-04

GB/T 9871-2008 硫化橡胶或热塑性橡胶老化性能的测定.拉伸应力松弛试验
简介：本标准规定了三种测量试样在给定伸长状态下应力变化的方法，目的是测定橡胶硫化胶的老化性能。方法A供在连续应变条件下的测量采用。方法B是在间歇应变条件下的测量的优先选择的方法。在方法A和B两种情况下，使用应力松弛仪记录在老化温度下的应力。方法C可以代替方法B用于在间歇应变条件下的测量。在方法C中，试样从老化环境中取出，在标准实验室温度下测量应力。在单一的老化高温下的测量，可用于质量控制的目的，如耐热老化的程度。根据GB/T 20028的描述的方法，在一系列温度下进行测量以预测长期的老化性能，可用于研究和开发的目的。在三个方法之间无法互相推算，所用的方法取决于试验目的。
信息：ICS：83.060 CCS：G40 发布：2008-04-01 实施：2008-09-01

ISO 6914:2013 硫化橡胶或热塑性橡胶——通过测量拉伸应力松弛测定老化特性
简介：
信息：ICS：83.060 CCS：发布：2013-11-21 实施：

GB/T 3512-2001 硫化橡胶或热塑性橡胶热空气加速老化和而热试验
简介：本标准适用于硫化橡胶或热塑橡胶在常压下进行热空气加速老化和耐热试验。
信息：ICS：83.060 CCS：G40 发布：2001-08-28 实施：2002-05-01

GOST ISO 188-2013 硫化橡胶或热塑性橡胶. 加速老化和耐热性试验
简介：
信息：ICS：83.060 CCS：发布：2013 实施：2015-01-01

JIS K6266-2007 硫化橡胶或热塑性橡胶.耐老化性能的测定
简介：この規格は，加硫ゴム及び熱可塑性ゴム(以下，加硫ゴムという。)の，屋外暴露試験及び実験室光源暴露試験について規定し，更に暴露後の試験片の色，外観，物理特性などの変化(耐候性)を求める方法について規定する
信息：ICS：83.060 CCS：G35 发布：2007-10-20 实施：

GB/T 3511-2001 硫化橡胶或热塑性橡胶直接自然气候老化试验方法
简介：本标准规定了硫化橡胶或热塑性橡胶表面受太阳光直接辐射，经受自然气候因素如日光、温度、水分、氧、臭氧等综合因素的作用的一种自然气候老化试验方法。本标准适用于硫化橡胶和热塑性橡胶在太阳光直接辐射和自然气候因素作用下的老化试验。
信息：ICS：83.060 CCS：G40 发布：2001-08-28 实施：2002-05-01

ASTM D750-2012 用人工风化装置对橡胶老化性的标准实施规程
简介：3.1x00a0;This practice describes procedures to use in determining the effects of an open-flame carbon-arc light source, an enclosed carbon-arc light source, a xenon-arc light source, or a fluorescent UV source along with heat and moisture on rubber specimens held in a jig or holder with or without a specified strain. The purpose is to attempt to accelerate the effects produced by light, heat, and moisture in the natural environment. Exposures are not intended to simulate the deterioration caused by localized weather phenomena, such as atmospheric pollution, biological attack, and saltwater exposure. The Significance and Use section in Practice G151 and the standard for the appropriate apparatus, that is, Practices G152, G153, G154, or G155 should be consulted for additional information on significance and use of the exposure tests. 3.2x00a0;The primary criterion used in estimating resistance to weathering is the percentage decrease in tensile strength and in elongation at break. A supplementary criterion for estimating resistance to weathering is the observed extent of surface crazing and cracking. 3.3x00a0;Results obtained by use of these test procedures should not be represented as equivalent to those of any natural exposure test until the degree of quantitative correlation has been established for the material in question. 3.4x00a0;Because of differences in the spectral power distributions of the exposure sources as well as the other conditions in the different types of laboratory weathering tests, the different procedures may not result in the same performance rankings or types of failure modes of the materials. Comparisons shall not be made of relative stabilities of materials exposed in different types of apparatus. 3.5x00a0;When conducting exposures in devices that use laboratory light sources, it is important to consider how well the artificial weathering conditions will reproduce property changes and failure modes caused by end-use environments on the materials being tested. 3.6x00a0;Practices G151, G152, G153, G154, and G155 recommend that a similar material of known performance (a control) be exposed simultaneously with the test specimen to provide a standard for comparative purposes. Preferably, a control material known to have poor durability as well as one that has good durability should be used. The reason for using a control is that reproducibility in ranking stabilities is usually bett............
信息：ICS：83.060 (Rubber) CCS：G34 发布：2012 实施：

ISO 188:2007 硫化橡胶或热塑性橡胶.加速老化和耐热试验
简介：
信息：ICS：83.060 CCS：发布：2007-06-19 实施：

GB/T 7544.7-1999 橡胶避孕套第7部分: 热空气老化
简介：本标准规定了带包装避孕套贮存期间耐老化性能的测定方法。GB/T 7544.6和GB/T 7544.9与本方法一同使用。
信息：ICS：11.200 CCS：C63 发布：1999-06-29 实施：2000-05-01

ASTM D750-2012(2017) 利用人工老化装置使橡胶劣化的标准实施规程
简介：3.1x00a0;This practice describes procedures to use in determining the effects of an open-flame carbon-arc light source, an enclosed carbon-arc light source, a xenon-arc light source, or a fluorescent UV source along with heat and moisture on rubber specimens held in a jig or holder with or without a specified strain. The purpose is to attempt to accelerate the effects produced by light, heat, and moisture in the natural environment. Exposures are not intended to simulate the deterioration caused by localized weather phenomena, such as atmospheric pollution, biological attack, and saltwater exposure. The Significance and Use section in Practice G151 and the standard for the appropriate apparatus, that is, Practices G152, G153, G154, or G155 should be consulted for additional information on significance and use of the exposure tests. 3.2x00a0;The primary criterion used in estimating resistance to weathering is the percentage decrease in tensile strength and in elongation at break. A supplementary criterion for estimating resistance to weathering is the observed extent of surface crazing and cracking. 3.3x00a0;Results obtained by use of these test procedures should not be represented as equivalent to those of any natural exposure test until the degree of quantitative correlation has been established for the material in question. 3.4x00a0;Because of differences in the spectral power distributions of the exposure sources as well as the other conditions in the different types of laboratory weathering tests, the different procedures may not result in the same performance rankings or types of failure modes of the materials. Comparisons shall not be made of relative stabilities of materials exposed in different types of apparatus. 3.5x00a0;When conducting exposures in devices that use laboratory light sources, it is important to consider how well the artificial weathering conditions will reproduce property changes and failure modes caused by end-use environments on the materials being tested. 3.6x00a0;Practices G151, G152, G153, G154, and G155 recommend that a similar material of known performance (a control) be exposed simultaneously with the test specimen to provide a standard for comparative purposes. Preferably, a control material known to have poor durability as well as one that has good durability should be used. The reason for using a control is that reproducibility in ranking stabilities is usually better than reproducibility of absolute changes. Therefore, the use of controls is particularly important when test materials are not being compared with one another. 1.1x00a0;This practice covers specific variations in the test conditions and procedures that shall be applicable when Practice G151 plus either Practice G152, G153, G154, or
信息：ICS：83.060 CCS：G34 发布：2012 实施：

ISO 188-2007 硫化橡胶或热塑性橡胶.加速老化和耐热性试验
简介：This International Standard specifies accelerated ageing or heat resistance tests on vulcanized orthermoplastic rubbers. Two methods are given:Method A: air-oven method using a cell-type oven or cabinet oven with low air speed and a ventilation of 3 to10 changes per hour;Method B: air-oven method using a cabinet oven with forced air circulation by means of a fan and aventilation of 3 to 10 changes per hour.
信息：ICS：83.060 CCS：G34 发布：2007-06 实施：

ISO 6914:2021 橡胶硫化或热塑性 - 通过测量张力中的应力松弛测定老化特性
简介：
信息：ICS：83.060 CCS：发布：2021-02-15 实施：

NF T46-004-2011 硬化或热塑橡胶.加速老化和耐热性的测试.
简介：
信息：ICS：83.060 CCS：G34 发布：2011-12-01 实施：2011-12-02

TCVN 2229-2007 橡胶,硫化或热塑性塑料.加速老化和耐热性试验
简介：
信息：ICS： CCS：发布：2007 实施：

ISO 6914-2021 硫化橡胶或热塑性橡胶. 老化性能的测定 (拉伸应力松弛试验)
简介：
信息：ICS： CCS：G40 发布：2021-02-00 实施：

BS ISO 188-2011 硫化橡胶或热塑性橡胶.加速老化和耐热性试验
简介：
信息：ICS：83.060 CCS：G34 发布：2011-10-31 实施：2011-10-31

BS EN 1297-2004 防水用软薄板.屋顶防水用沥青、塑料和橡胶薄板.长期暴露于紫外线辐射、升温和水雨综合条件的人工老化法
简介：This document specifies the method for exposure of factory made bitumen or plastic or rubber sheets for roof waterproofing to combined effects of long term exposure by UV radiation, elevated temperature and water as means of artificial ageing.
信息：ICS：91.100.50 CCS：Q17 发布：2006-12-29 实施：2006-12-29

ASTM D750-2012(2021) 利用人工气候老化装置使橡胶劣化的标准规程
简介：1.1?This practice covers specific variations in the test conditions and procedures that shall be applicable when Practice G151 plus either Practice G152, G153, G154, or G155 are employed for exposure of vulcanized rubber compounds. It also covers the preparation of test specimen
信息：ICS： CCS：A40/49 发布：2021 实施：

BS ISO 188-2011 硫化橡胶或热塑性橡胶.加速老化和耐热性试验
简介：
信息：ICS：83.060 CCS：G34 发布：2011-10-31 实施：2011-10-31

KS K 0856-2006 橡胶或塑料涂层织物加速老化试验
简介：
信息：ICS：59.080.40 CCS：发布：2006-12-07 实施：

ISO 1419-2019 橡胶或塑料涂层织物.加速老化试验
简介：
信息：ICS：59.080.40 CCS：发布：2019-05-23 实施：

ISO 188-2011 硬化或热塑橡胶加速老化和耐热性测定
简介：
信息：ICS：83.060 CCS：G34 发布：2011-10 实施：

ASTM D750-2006 用人工风蚀装置对橡胶老化性的标准试验方法
简介：1.1 This test method covers specific variations in the test conditions and procedures that shall be applicable when Practice G 151 plus either Practice G 152, G 153, G 154, or G 155 are employed for exposure of vulcanized rubber compounds. It also covers the preparation of test specimens and the evaluation of results.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：83.060 (Rubber) CCS：G40 发布：2006 实施：

ISO 1419:2019 橡胶或塑料涂层织物.加速老化试验
简介：
信息：ICS：59.080.40 CCS：发布：2019-05-23 实施：

ISO 188:2011 硫化橡胶或热塑性橡胶——加速老化和耐热性试验
简介：
信息：ICS：83.060 CCS：发布：2011-09-26 实施：

NF P84-106-2005 防水用软薄板.屋顶防水用沥青、塑料和橡胶薄板.长期暴露于紫外线辐射、高温和水的组合条件下的人工老化法
简介：
信息：ICS：91.100.50 CCS：Q17 发布：2005-01-01 实施：2005-01-20

KS M ISO 1419-2018 橡胶或塑料涂层织物.加速老化试验
简介：
信息：ICS：83.140 CCS：发布：2018-12-28 实施：

KS M ISO 6914-2010 硫化或热塑性橡胶.用拉伸中应力松弛测量法测定老化特性
简介：이 표준은 고무의 노화 특성을 측정하기 위한 목적으로, 주어진 신장에서 시험편의 응력 변화
信息：ICS：83.06 CCS：G34 发布：2010-04-21 实施：2010-04-21

DIN EN 1297-2004 防水用软薄板.屋顶防水用沥青、塑料和橡胶薄板.长期暴露于紫外线辐射、高温和水的组合条件下的人工老化法
简介：This European Standard specifies the method for exposure of factury made betumen or plastic or rubber sheets for roof water proofing to combined effects of long term exposures by UV radioation, elevated temperature and water as means of artificial ageing. It definds one common precedure to be applied as a method for artificial ageing to all types of flexible sheets for roof waterproofing. It is intended for application in roofing but it can also be applied to other areas where it is relevant.,,
信息：ICS：91.100.50 CCS：Q17 发布：2004-12 实施：

ISO 1419:2018 橡胶或塑料涂层织物.加速老化试验
简介：
信息：ICS：59.080.40 CCS：发布：2018-08-10 实施：

EN 1297-2004 防水用软薄板.屋顶防水用沥青,塑料和橡胶薄板.长期暴露于紫外线辐射,高温和水的组合条件下的人工老化法
简介：This document specifies the method for exposure of factory made bitumen or plastic or rubber sheets for roof waterproofing to combined effects of long term exposure by UV radiation, elevated temperature and water as means of artificial ageing.
信息：ICS：91.100.50 CCS：发布：2004-09-01 实施：

T/CAAMM 16-2018 农业机械用橡胶软管及软管组合件耐臭氧老化试验方法
简介：本标准规定了农业机械用橡胶软管及软管组合件耐臭氧老化试验装置、试样、试验条件、试验方法及试验报告。本标准适用于农业机械用各类纯胶管或增强型橡胶软管及软管组合件，包括空气胶管、输水胶管、输油橡胶软管及软管组合件等的耐臭氧老化性能的检测。
信息：ICS：65.060.01 CCS：C357 发布：2018-03-30 实施：2018-04-11

JIS K6257-2010 硫化或热塑性橡胶.热老化性能的测定
简介：This Japanese Industrial Standard specifies the determination method of heat ageing properties of vulcanized rubber and thermoplastic rubber according to the accelerated ageing test and/or the heat resistance test. The test methods include the following Method A and Method B.
信息：ICS：83.060 CCS：G34 发布：2010-04-20 实施：

ISO 6914-2004 硫化或热固性橡胶.用应力松弛测量法测定老化特性
简介：This International Standard describes three methods for the measurement of the change of stress in a test piece at a given elongation for the purpose of determining the ageing characteristics of the rubber vulcanizate.— Method A is intended for measurement under continuous strain conditions.— Method B is the preferred method for measurement under intermittent strain conditions.In the case of both methods A and B, a stress relaxometer is used to record the stress at the temperature of ageing.— Method C is an alternative to method B for measurement under intermittent strain conditions in which the test piece is removed from the ageing environment for measurement of the stress at the standard laboratory temperature.The necessary calibration schedule for this type of measurement is given in Annex A.Measurements at a single elevated ageing temperature may be used for quality control purposes as a measure of heat-ageing resistance. Measurements at a number of temperatures may be used for research and development purposes to estimate long-term ageing characteristics in accordance with the procedures described in ISO 11346.No agreement between the three methods should be inferred. The method used will depend on the purpose of the test.
信息：ICS：83.060 CCS：G34 发布：2004-04 实施：

JIS K6257-2017 硫化或热塑性橡胶.热老化性能的测定
简介：
信息：ICS：83.060 CCS：G34 发布：2017-10-20 实施：

KS M ISO 188-2009 硫化或热塑橡胶.加速老化和耐热性试验
简介：이 표준은 가황 또는 열가소성 고무에 대한 촉진 노화 또는 내열 시험에 대하여 규정한다.
信息：ICS：83.06 CCS：G34 发布：2009-12-11 实施：2009-12-11

ISO 6914:2004 硫化橡胶或热塑性橡胶.用应力松弛测量法测定老化特性
简介：
信息：ICS：83.060 CCS：发布：2004-03-30 实施：

JIS K6257-2017 硫化或热塑性橡胶.热老化性能的测定
简介：
信息：ICS：83.060 CCS：G34 发布：2017-10-20 实施：

SANS 54-2009 硫化或热塑性橡胶.加速老化和耐热性试验
简介：Specifies two methods of accelerated ageing or heat resistance tests on vulcanized or thermoplastic rubbers.
信息：ICS：83.060 CCS：G34 发布：2009-04-24 实施：

ISO 188 CORR 1-2003 硫化或热塑性橡胶.加速老化和耐热性试验.技术勘误1
简介：
信息：ICS：83.060 CCS：G34 发布：2003-08 实施：

KS M ISO 6914-2015(2021) 硫化橡胶或热塑性橡胶拉伸应力松弛测定老化特性
简介：
信息：ICS：83.060 CCS：发布：2015-12-24 实施：

UNE 18 055 由橡胶和纺织品组成的传送绶带．发生人为老化后对橡胶覆盖的高槽负荷变动和加大的确定
简介：La presente norma define el método de prueba para la determinación de la disminucion,artificialmente acelerada,de las características físicas (envejecimiento artificial) de tas cubiertas de goma de las bandas transportadoras.
信息：ICS： CCS：发布：2008-1-1 实施：

NF G37-105-2-2003 橡胶和塑料涂层织物.加速老化试验.第2部分:物理老化.光或气候老化作用
简介：
信息：ICS：59.080.40 CCS：W59 发布：2003-07-01 实施：2003-07-05