沉淀标准检测标准沉淀标准-中析研究所检测

(CMA)

(CNAS)

(ISO)

(高新技术企业)

沉淀标准相关标准参考信息

ASTM D6845-22 沉淀水合CTAB（十六烷基三甲基溴化铵）表面积二氧化硅的标准试验方法
简介：
信息：ICS：71.100.55 CCS：发布：2022-11-01 实施：

ASTM D5515-2017a 用膨胀计测定沥青煤沉淀特性的标准试验方法
简介：5.1x00a0;Values of the dilatation properties of coals may be used to predict or explain the behavior of a coal or blends during carbonization or in other processes such as gasification, liquefaction, and combustion. 1.1x00a0;This test method specifies a procedure for the measurement of the swelling of bituminous coal using a dilatometer. 1.2x00a0;The test method is limited in applicability to those coals which have a free swelling index x2265;1 as determined in accordance with Test Method D720. 1.3x00a0;The values stated in SI units (IEEE/ASTM8201;SI-10) are to be regarded as standard. 1.4x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.5x00a0;This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
信息：ICS：75.140 CCS：E43 发布：2017 实施：

ASTM A1082/A1082M-2015 特殊目的应用高强度沉淀硬化和双相不锈钢螺栓的标准规格
简介：1.1x00a0;This specification covers high strength stainless steel bolting for special purpose applications such as pressure vessels. Several grades of precipitation-hardened and duplex (ferritic-austenitic) stainless steels are covered. Selection will depend upon design, service conditions, mechanical properties and characteristics related to the application. 1.2x00a0;The following referenced general requirements are indispensable for application of this specification: Specification A962/A962M. 1.3x00a0;Supplementary Requirements are provided for use at the option of the purchaser. The Supplementary Requirements shall only apply when specified individually by the purchaser in the purchase order or contract. 1.4x00a0;This specification is expressed in both inch-pound units and in SI units; however, unless the purchase order or contract specifies the applicable x201c;Mx201d; specification designation (SI units), the inch-pound units shall apply. 1.5x00a0;The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.6x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：77.080.20 CCS：发布：2015 实施：

ASTM D8016-22 沉淀水合西尔斯值二氧化硅的标准试验方法
简介：
信息：ICS：83.040.20 CCS：发布：2022-11-01 实施：

ASTM D5515-2017 用膨胀计测定沥青煤沉淀特性的标准试验方法
简介：5.1x00a0;Values of the dilatation properties of coals may be used to predict or explain the behavior of a coal or blends during carbonization or in other processes such as gasification, liquefaction, and combustion. 1.1x00a0;This test method specifies a procedure for the measurement of the swelling of bituminous coal using a dilatometer. 1.2x00a0;The test method is limited in applicability to those coals which have a free swelling index x2265;1 as determined in accordance with Test Method D720. 1.3x00a0;The values stated in SI units (IEEE/ASTM8201;SI-10) are to be regarded as standard. 1.4x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.5x00a0;This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
信息：ICS：75.140 CCS：E43 发布：2017 实施：

ASTM B637-2015 中温或高温用沉淀硬化和冷加工镍合金棒材, 锻件和锻坯的标准规格
简介：1.1x00a0;This specification2 covers hot- and cold-worked precipitation-hardenable nickel alloy rod, bar, forgings, and forging stock for moderate or high temperature service (Table 1). (A)x00a0;If determined.(B)x00a0;The element shall be determined arithmetically by difference. 1.2x00a0;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.
信息：ICS：9925; CCS：发布：2015 实施：

ASTM E278-21 用磷钼酸盐共沉淀和硝酸滴定法测定铁矿石中磷的标准试验方法
简介：
信息：ICS：73.060.10 CCS：发布：2021-10-01 实施：

ASTM B1007-2017 焊接沉淀硬化或冷加工镍合金管的标准规格
简介：1.1x00a0;This specification covers nominal and minimum wall-thickness welded tubes and welded and cold worked tubes made from the nickel alloys listed in Table 1. Anticipated uses cover applications where strength and strength at elevated temperatures are desired attributes. Some examples are hydraulic control lines, boilers, heat exchangers, and solar absorbers. (A)x00a0;Columbium or Niobium (Nb) are references to the same element.(B)x00a0;Remainder: The element may be determined arithmetically by difference.(C)x00a0;Minimum: The element may be determined arithmetically by difference. 1.2x00a0;Tube shall be supplied in one of the following conditions; cold worked, cold worked and precipitation hardened, solution annealed plus precipitation hardened, or solution annealed and descaled conditions. When atmosphere control is used, descaling is not necessary. 1.3x00a0;This specification covers tube 1/8x00a0;to 6 in. (3.2 to 152.4 mm) in outside diameter and 0.015 to 0.148 in. (0.41 to 3.7 mm) inclusive in wall thickness. 1.4x00a0;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6x00a0;This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
信息：ICS：23.040.15 CCS：H60 发布：2017 实施：

ASTM A1014/A1014M-2015 高温服务用沉淀硬化螺栓 (UNS N07718) 的标准规格
简介：1.1x00a0;This specification covers precipitation hardening bolting material (UNS N07718) and bolting components for high temperature service. See Specification A962/A962M for the definition of x201c;bolting.x201d; 1.2x00a0;The following referenced general requirements are indispensable for application of this specification: Specification A962/A962M. 1.3x00a0;Supplementary requirements are provided for use at the option of the purchaser. The supplementary requirements only apply when specified individually in the purchase order or contract. 1.4x00a0;This specification is expressed in both inch-pound and in SI units. However, unless the purchase order or contract specifies the applicable M designation (SI units), the inch-pound units shall apply. 1.5x00a0;The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
信息：ICS：77.140.30 CCS：发布：2015 实施：

ASTM D7928-21e1 使用沉淀（比重计）分析的细粒土壤的粒度分布（梯度）的标准测试方法
简介：
信息：ICS：13.080.20 CCS：发布：2021-05-01 实施：

ASTM D7928-16 使用沉淀（比重计）分析的细粒土壤的粒度分布（梯度）的标准测试方法
简介：
信息：ICS：13.080.20 CCS：发布：2016-05-01 实施：

ASTM D6038-14 用沉淀温度&40测定树脂/溶剂混合物相容性的标准试验方法；浊点&41
简介：
信息：ICS：83.040.01 CCS：发布：2014-01-01 实施：

ASTM D7928-21 使用沉淀（比重计）分析的细粒土壤的粒度分布（梯度）的标准测试方法
简介：
信息：ICS：13.080.20 CCS：发布：2021-05-01 实施：

ASTM D7928-16e1 使用沉淀（比重计）分析的细粒土壤的粒度分布（梯度）的标准测试方法
简介：
信息：ICS：13.080.20 CCS：发布：2016-05-01 实施：

ASTM F2985-2014 成人可进入下水道和管涵中PVC分段面板沉淀系统安装的标准实践规程
简介：1.1x00a0;The practice describes the procedures for the rehabilitation of gravity pipes, culverts, tunnels, and conduits by the installation of a field-fabricated PVC liner system. After installation of the liner system, cementitious grout is pumped into the annular space between the liner and the host structure. The rehabilitation of the host structure by this installation practice results in a rigid composite structure (PVC liner/grout/existing pipe). This type of rehabilitation process is suitable for a variety of gravity pipe applications such as storm sewers, sanitary sewers, and culverts; and with geometries including circular, egg, ovoid, elliptical, arch, and site-specific composite shapes. 1.2x00a0;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS： CCS：发布：2014 实施：

ASTM E1047-85(2021) 血液沉淀管 Wintrobe 玻璃一次性标准规格
简介：
信息：ICS： CCS：发布：2021-01-01 实施：

ASTM E1728-16 使用擦拭取样方法收集沉淀粉尘样品进行后续铅测定的标准做法
简介：
信息：ICS：13.080.05 CCS：发布：2016-01-01 实施：

ASTM D5256-2014 溶解水成沉淀用动态溶剂系统的相关功效的标准试验方法
简介：5.1x00a0;This test method is useful because the choice of a solvent system for removing water-formed deposits depends upon the ability of the dynamic solvent system to dissolve both unattached and attached deposits. 1.1x00a0;This test method covers the determination of the relative efficacy of dynamic solvent systems for dissolving water-formed deposits that have been removed from the underlying material or deposits attached to the underlying material. 1.2x00a0;The nature of this test method is such that statements of precision and bias as determined by round robin tests could mislead users of this test method (see Sections 11 and 12). Therefore, no precision and bias statements are made. 1.3x00a0;The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard. 1.4x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：13.060.50 (Examination of water for chemical subst CCS：发布：2014 实施：

ASTM D6234-13(2020) 采用合成沉淀法浸提采矿废弃物的标准试验方法
简介：
信息：ICS：73.020 CCS：发布：2020-09-01 实施：

ASTM D7928-2016 采用沉淀 (比重计) 分析测定细粒土粒径分布 (级配) 的标准试验方法
简介：5.1x00a0;Particle-size distribution (gradation) is a descriptive term referring to the proportions by dry mass of a soil distributed over specified particle-size ranges. The gradation curve generated using this method yields the amount of silt and clay size fractions present in the soil based on size definitions, not mineralogy or Atterberg limit data. 5.2x00a0;Determination of the clay size fraction, which is material finer than 2 x00b5;m, is used in combination with the Plasticity Index (Test Methods D4318) to compute the activity, which provides an indication of the mineralogy of the clay fraction. 5.3x00a0;The gradation of the silt and clay size fractions is an important factor in determining the susceptibility of fine-grained soils to frost action. 5.4x00a0;The gradation of a soil is an indicator of engineering properties. Hydraulic conductivity, compressibility, and shear strength are related to the gradation of the soil. However, engineering behavior is dependent upon many factors, such as effective stress, mineral type, structure, plasticity, and geological origin, and cannot be based solely upon gradation. 5.5x00a0;Some types of soil require special treatment in order to correctly determine the particle sizes. For example, chemical cementing agents can bond clay particles together and should be treated in an effort to remove the cementing agents when possible. Hydrogen peroxide and moderate heat can digest organics. Hydrochloric acid can remove carbonates by washing and Dithionite-Citrate-Bicarbonate extraction can be used to remove iron oxides. Leaching with test water can be used to reduce salt concentration. All of these treatments, however, add significant time and effort when performing the sedimentation test and are allowable but outside the scope of this test method. 5.6x00a0;The size limits of the sedimentation test are from about 100 x00b5;m to about 1 x00b5;m. The length of time required to obtain a stable initial reading on the hydrometer controls the upper range of results, and the test duration controls the lower range. 5.7x00a0;The shape and density of the grains are important to the results. Stokesx2019; Law is assumed to be valid for spherical particles even though fine silt- and clay-sized particles are more likely to be plate-shaped and have greater mineral densities than larger particles. Note 5:x00a0;The quality of the result produced by this standard is dependent on the competence of the personnel performing it, and the suitability of the equipment and facilities used. Agencies that meet the criteria of Practice D3740 are generally considered capable of competent and objective testing/sampling/inspection/etc. Users of this standard are cautioned that compliance with Practice D3740 does not in itself assure reliable results. Reliable results depend on many factors; Practice D3740 provides a means of evaluating some of those factors. 1.1
信息：ICS： CCS：发布：2016 实施：

ASTM D6234-13 采用合成沉淀法浸提采矿废弃物的标准试验方法
简介：
信息：ICS：73.020 CCS：发布：2013-09-01 实施：

ASTM D6845-20 沉淀水合二氧化硅的标准试验方法&x2014；CTAB（十六烷基三甲基溴化铵）表面积
简介：
信息：ICS：71.100.55 CCS：发布：2020-06-01 实施：

ASTM B983-2016e1 沉淀硬化或者冷加工无缝镍合金管的标准规格
简介：1.1x00a0;This specification covers high strength, seamless pipe and tube of nickel alloys (UNS N07022, UNS N07725, UNS N07740, UNS N09945, UNS N09925, UNS N07718, UNS N10276, UNS N06985)2 as shown in Table 1. (A)x00a0;Minimum: The element may be determined arithmetically by difference.(B)x00a0;Remainder: The element may be determined arithmetically by difference. 1.2x00a0;Pipe and tube shall be supplied in the cold worked or cold worked and precipitations hardened or solution annealed plus precipitation hardened and descaled conditions. When atmosphere control is used, descaling is not necessary. 1.3x00a0;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.5x00a0;This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
信息：ICS：23.040.15 CCS：P94 发布：2016 实施：

ASTM A693-2013 沉淀硬化不锈钢和耐热钢板材、薄板和带材标准规格
简介：1.1x00a0;This specification2 covers precipitation-hardening stainless steel plate, sheet, and strip. The mechanical properties of these steels are developed by suitable low-temperature heat treatments generally referred to as precipitation hardening. 1.2x00a0;These steels are used for parts requiring corrosion resistance and high strength at room temperature or at temperatures up to 600x00b0;F (315x00b0;C). Some of these steels are particularly suitable for moderate to severe drawing and forming in the solution-treated condition. Others are capable of mild forming only. They are suitable for machining in the solution-annealed condition, after which they may be hardened to the mechanical properties specified in this standard without danger of cracking or distortion. 1.3x00a0;The values stated in inch-pound units are to be regarded as the standard.
信息：ICS：77.140.20 (Steels of high quality); 77.140.50 (Fla CCS：H46 发布：2013 实施：

ASTM D4807-05(2020) 膜过滤沉淀原油的标准试验方法
简介：
信息：ICS：75.040 CCS：发布：2020-05-01 实施：

ASTM A747/A747M-2016 沉淀硬化不锈钢铸件的标准规格
简介：1.1x00a0;This specification covers iron-chromium-nickel-copper corrosion-resistant steel castings, capable of being strengthened by precipitation hardening heat treatment. 1.2x00a0;These castings may be used in services requiring corrosion resistance and high strengths at temperatures up to 600x00b0;F [315x00b0;C]. They may be machined in the solution-annealed condition and subsequently precipitation hardened to the desired high-strength mechanical properties specified in Table S14.1 with little danger of cracking or distortion. 1.3x00a0;The material is not intended for use in the solution-annealed condition. Note 1:x00a0;If the service environment in which the material is to be used is considered conducive to stress-corrosion cracking, precipitation hardening should be performed at a temperature that will minimize the susceptibility of the material to this type of attack. 1.4x00a0;Supplementary requirements of an optional nature are provided for use at the option of the purchaser. The Supplementary requirements shall apply only when specified individually by the purchaser in the purchase order or contract. 1.5x00a0;This specification is expressed in both inch-pound units and in SI units; however, unless the purchase order or contract specifies the applicable M specification designation (SI units), the inch-pound units shall apply. 1.6x00a0;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.6.1x00a0;Within the text, the SI units are shown in brackets.
信息：ICS：77.140.80 CCS：发布：2016 实施：

ASTM D91-02(2012)e1 润滑油沉淀值的标准试验方法
简介：
信息：ICS：75.100 CCS：发布：2012-11-01 实施：

ASTM E1728/E1728M-20 使用擦拭取样方法收集沉淀粉尘样品进行后续铅测定的标准做法
简介：
信息：ICS：13.080.05 CCS：发布：2020-01-01 实施：

ASTM A891/A891M-2016 涡轮机转子盘和轮子用沉淀硬化铁基高温合金锻件的标准规格
简介：1.1x00a0;This specification covers precipitation hardening iron base superalloy forgings which are primarily intended for use as turbine rotor disks and wheels. 1.2x00a0;Two heat treatments are covered. Selection will depend upon design, service conditions, mechanical properties, and elevated temperature characteristics. 1.3x00a0;All of the provisions of Specification A788/A788M, apply, except as amended herein. 1.4x00a0;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
信息：ICS：77.140.85 CCS：发布：2016 实施：

ASTM D91-02(2012) 润滑油沉淀值的标准试验方法
简介：
信息：ICS：75.100 CCS：发布：2012-11-01 实施：

ASTM D8300-19 沉淀水合二氧化硅的标准试验方法&x2014；导电性
简介：
信息：ICS：83.040.20 CCS：发布：2019-11-01 实施：

ASTM A1014/A1014M-2016e1 高温服务用沉淀硬化螺栓(UNS N07718)的标准规格
简介：1.1x00a0;This specification covers precipitation hardening bolting material (UNS N07718) and bolting components for high temperature service. See Specification A962/A962M for the definition of x201c;bolting.x201d; 1.2x00a0;The following referenced general requirements are indispensable for application of this specification: Specification A962/A962M. 1.3x00a0;Supplementary requirements are provided for use at the option of the purchaser. The supplementary requirements only apply when specified individually in the purchase order or contract. 1.4x00a0;This specification is expressed in both inch-pound and in SI units. However, unless the purchase order or contract specifies the applicable M designation (SI units), the inch-pound units shall apply. 1.5x00a0;The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.6x00a0;This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
信息：ICS：77.140.30 CCS：H46 发布：2016 实施：

ASTM D7296-12 采用干式抽样方法收集沉淀粉尘样品的标准做法以便随后测定铍和化合物
简介：
信息：ICS：13.040.40 CCS：发布：2012-04-01 实施：

ASTM D91-02(2019) 润滑油沉淀值的标准试验方法
简介：
信息：ICS：75.100 CCS：发布：2019-05-01 实施：

ASTM A1014/A1014M-2016 高温服务用沉淀硬化螺栓 (UNS N07718) 的标准规格
简介：1.1x00a0;This specification covers precipitation hardening bolting material (UNS N07718) and bolting components for high temperature service. See Specification A962/A962M for the definition of x201c;bolting.x201d; 1.2x00a0;The following referenced general requirements are indispensable for application of this specification: Specification A962/A962M. 1.3x00a0;Supplementary requirements are provided for use at the option of the purchaser. The supplementary requirements only apply when specified individually in the purchase order or contract. 1.4x00a0;This specification is expressed in both inch-pound and in SI units. However, unless the purchase order or contract specifies the applicable M designation (SI units), the inch-pound units shall apply. 1.5x00a0;The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
信息：ICS：77.140.30 CCS：发布：2016 实施：

ASTM D6800-12 用还原沉淀预富集技术制备痕量金属的ICP-MS分析水样的标准实施规程
简介：
信息：ICS：13.060.45 CCS：发布：2012-03-01 实施：

ASTM D7296-18 采用干式抽样方法收集沉淀粉尘样品的标准做法以便随后测定铍和化合物
简介：
信息：ICS：13.040.40 CCS：发布：2018-11-01 实施：

ASTM A747/A747M-2016a 沉淀硬化的不锈钢铸件的标准规格
简介：1.1x00a0;This specification covers iron-chromium-nickel-copper corrosion-resistant steel castings, capable of being strengthened by precipitation hardening heat treatment. 1.2x00a0;These castings may be used in services requiring corrosion resistance and high strengths at temperatures up to 600x00b0;F [315x00b0;C]. They may be machined in the solution-annealed condition and subsequently precipitation hardened to the desired high-strength mechanical properties specified in Table S24.1 with little danger of cracking or distortion. 1.3x00a0;The material is not intended for use in the solution-annealed condition. Note 1:x00a0;If the service environment in which the material is to be used is considered conducive to stress-corrosion cracking, precipitation hardening should be performed at a temperature that will minimize the susceptibility of the material to this type of attack. 1.4x00a0;Supplementary requirements of an optional nature are provided for use at the option of the purchaser. The Supplementary requirements shall apply only when specified individually by the purchaser in the purchase order or contract. 1.5x00a0;This specification is expressed in both inch-pound units and in SI units; however, unless the purchase order or contract specifies the applicable M specification designation (SI units), the inch-pound units shall apply. 1.6x00a0;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.6.1x00a0;Within the text, the SI units are shown in brackets.
信息：ICS：77.140.80 CCS：发布：2016 实施：

ASTM D6845-12 二氧化硅沉淀水合的标准测试方法
简介：
信息：ICS：71.100.55 CCS：发布：2012-01-01 实施：

ASTM D6800-18 用还原沉淀预富集技术制备痕量金属的ICP-MS分析水样的标准实施规程
简介：
信息：ICS：13.060.45 CCS：发布：2018-07-15 实施：

ASTM E278-01(2015)e1 通过磷钼酸盐共沉淀和硝酸滴定法测定铁矿石中磷的标准试验方法
简介：
信息：ICS：73.060.10 CCS：发布：2015-11-15 实施：

ASTM D6845-2012 沉淀的水合硅石的标准试验方法.CTAB（溴化十六烷基三甲基铵）表面积
简介：The CTAB molecule is relatively large; so it is not adsorbed in micropores or on surface roughness. Thus, the CTAB surface area reflects only the surface of the silica that is available for interaction with rubber molecules.1.1 This test method covers the measurement of the specific surface area of precipitated silicas exclusive of area contained in micropores too small to admit hexadecyltrimethylammonium bromide (cetyltrimethylammonium bromide, commonly referred to as CTAB) molecules. This test method is suitable for characterizing rubber-grade silicas of all types. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：71.100.55 CCS：G17 发布：2012 实施：

ASTM D8016-18e1 沉淀水合二氧化硅的标准试验方法&x2014；西尔斯数
简介：
信息：ICS：83.040.20 CCS：发布：2018-06-01 实施：

ASTM D8016-15 沉淀水合二氧化硅的标准试验方法&x2014；西尔斯数
简介：
信息：ICS：83.040.20 CCS：发布：2015-11-01 实施：

ASTM A747/A747M-2012 沉淀硬化不锈钢铸件的标准规格
简介：1.1 This specification covers iron-chromium-nickel-copper corrosion-resistant steel castings, capable of being strengthened by precipitation hardening heat treatment. 1.2 These castings may be used in services requiring corrosion resistance and high strengths at temperatures up to 600x00B0;F [315x00B0;C]. They may be machined in the solution-annealed condition and subsequently precipitation hardened to the desired high-strength mechanical properties specified in Table S14.1 with little danger of cracking or distortion. 1.3 The material is not intended for use in the solution-annealed condition. Note 18212;If the service environment in which the material is to be used is considered conducive to stress-corrosion cracking, precipitation hardening should be performed at a temperature that will minimize the susceptibility of the material to this type of attack. 1.4 Supplementary requirements of an optional nature are provided for use at the option of the purchaser. The Supplementary requirements shall apply only when specified individually by the purchaser in the purchase order or contract. 1.5 This specification is expressed in both inch-pound units and in SI units; however, unless the purchase order or contract specifies the applicable M specification designation (SI units), the inch-pound units shall apply. 1.6 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.6.1 Within the text, the SI units are shown in brackets.
信息：ICS：77.140.80 (Iron and steel castings) CCS：J31 发布：2012 实施：

ASTM D8016-18 沉淀水合二氧化硅的标准试验方法&x2014；西尔斯数
简介：
信息：ICS：83.040.20 CCS：发布：2018-06-01 实施：

ASTM E1047-85(2015) 血液沉淀管 Wintrobe 玻璃一次性标准规格
简介：
信息：ICS： CCS：发布：2015-06-01 实施：

ASTM D6800-2012 微量金属的电感耦合等离子体质谱(ICP-MS)分析法使用还原沉淀预浓缩技术对水样制备的标准操作规程
简介：Ambient marine waters generally contain very low concentrations of toxic metals that require sensitive analytical methods, such as ICP-MS, to detect and measure the metalx0027;s concentrations. Due to the high dissolved salt concentrations present in seawater, sample pretreatment is required to remove signal suppression and significant polyatomic interferences due to the matrix both of which compromise detection limits.1.1 Toxic elements may be present in ambient waters and may enter the food chain via uptake by plants and animals; the actual concentrations of toxic metals are usually sub-ng/mL. The U.S. EPA has published its Water Quality Standards in the U.S. Federal Register 40 CFR 131.36, Minimum requirements for water quality standards submission, Ch. I (7-1-00 Edition), see Annex, Table A1.1. The U.S. EPA has also developed Method 1640 to meet these requirements, see Annex, Table A1.2. 1.2 Inductively Coupled Plasma Mass Spectroscopy (ICP-MS) is a technique with sufficient sensitivity to routinely measure toxic elements in ambient waters, both fresh and saline (Test Method D5673). However saline and hard water matrices pose analytical challenges for direct multielement analysis by ICP-MS at the required sub-ng/mL levels. 1.3 This standard practice describes a method used to prepare water samples for subsequent multielement analysis using ICP-MS. The practice is applicable to seawater and fresh water matrices, which may be filtered or digested. Samples prepared by this method have been analyzed by ICP-MS for the elements listed in Annex, Table A1.3). 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：13.060.45 (Examination of water in general) CCS：发布：2012 实施：

ASTM D6845-18 沉淀水合二氧化硅的标准试验方法&x2014；CTAB（十六烷基三甲基溴化铵）表面积
简介：
信息：ICS：71.100.55 CCS：发布：2018-02-01 实施：

ASTM D4807-05(2015) 膜过滤沉淀原油的标准试验方法
简介：
信息：ICS：75.040 CCS：发布：2015-04-01 实施：

ASTM B637-2012 高温工作沉淀硬化镍合金棒材、锻件及锻坯标准规格
简介：1.1 This specification covers hot- and cold-worked precipitation-hardenable nickel alloy rod, bar, forgings, and forging stock for moderate or high temperature service (Table 1). 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use. TABLE 1 Chemical Requirements ElementComposition Limits, % UNS N07022UNS N07208UNS N07252 (Formerly Grade 689)UNS N07001 (Formerly Grade 685)UNS N07500 (Formerly Grade 684)UNS N07750 (Formerly Grade 688)UNS N07718 (Formerly Grade 718) Carbon0.010 max0.04x2013;0.080.10x2013;0.200.03x2013;0.100.15 max0.08 max0.08 max Manganese0.5 max0.3 max0.50 max1.00 max0.75 max1.00 max0.35 max Silicon0.08 max0.15 max0.50 max0.75 max0.75 max0.50 max0.35 max Phosphorus0.025 max0.015 max0.015 max0.030 max0.015 max...0.015 max Sulfur0.015 max0.015 max0.015 max0.030 max0.015 max0.01 max0.015 max Chromium20.0x2013;21.418.5x20......
信息：ICS：77.150.40 (Nickel and chromium products) CCS：H62 发布：2012 实施：

ASTM D91-02(2017) 润滑油沉淀值的标准试验方法
简介：
信息：ICS：75.100 CCS：发布：2017-07-01 实施：

ASTM D3976-92(2015) 化学分析沉淀样品的制备标准实践
简介：
信息：ICS：13.060.45 CCS：发布：2015-01-01 实施：

ASTM A1082/A1082M-2012 专用设施用高强度沉淀硬化和双相不锈钢螺栓的标准规格
简介：1.1 This specification covers high strength stainless steel bolting for special purpose applications such as pressure vessels. Several grades of precipitation-hardened and duplex (ferritic-austenitic) stainless steels are covered. Selection will depend upon design, service conditions, mechanical properties and characteristics related to the application. 1.2 The following referenced general requirements are indispensable for application of this specification: Specification A962/A962M. 1.3 Supplementary Requirements are provided for use at the option of the purchaser. The Supplementary Requirements shall only apply when specified individually by the purchaser in the purchase order or contract. 1.4 This specification is expressed in both inch-pound units and in SI units; however, unless the purchase order or contract specifies the applicable ???M??? specification designation (SI units), the inch-pound units shall apply. 1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：77.080.20 (Steels) CCS：J13 发布：2012 实施：

ASTM D7928-17 使用沉淀（比重计）分析的细粒土壤的粒度分布（梯度）的标准测试方法
简介：
信息：ICS：13.080.20 CCS：发布：2017-05-01 实施：

ASTM D6328-2012 大气湿度沉淀的化学分析的质量保证协议的标准指南
简介：1.1 This guide describes quality assurance (QA) protocols for the determination of the anions and cations in Atmospheric Wet Deposition (AWD) shown in Table 1.TABLE 1 Common Techniques of Analysis for Atmospheric Wet Deposition Samples Automated Colorimetry Ion Chromatography NH4+ Cl???, NO3 ???, SO42???, NH4+, Ca2+, Mg2+, Na+, K+ Flame Atomic Absorption Spectrophotometry Electrometric Na+, K+, Ca2+ , Mg2+ pH, specific conductance Inductively Coupled Plasma Spectrometry Na+, K+, Ca2+, Mg2+ 1.2 Included in this guide are minimum recommended requirements for the preparation of calibration standards and suggested procedures for validating laboratory measurement results. 1.3 This guide describes minimum requirements for the frequency of analysis of quality assurance samples and recommends procedures for the evaluation of quality assurance data. 1.4 The guidex0027;s recommendations are based upon expected anion and cation concentrations in AWD (1) 2 and Appendix X1. 1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：03.120.10 (Quality management and quality assuranc CCS：Z15 发布：2012 实施：

ASTM D1739-98(2017) 防尘（可沉淀颗粒物）的收集和测量的标准测试方法
简介：
信息：ICS：13.040.20 CCS：发布：2017-03-01 实施：

ASTM B983-2015 沉淀硬化或者冷加工无缝镍合金管的标准规格
简介：1.1x00a0;This specification covers high strength, seamless pipe and tube of nickel alloys (UNS N07022, UNS N07725, UNS N07740, UNS N09945, UNS N09925, UNS N07718, UNS N10276, UNS N06985)2 as shown in Table 1. (A)x00a0;Minimum: The element may be determined arithmetically by difference.(B)x00a0;Remainder: The element may be determined arithmetically by difference. 1.2x00a0;Pipe and tube shall be supplied in the cold worked or cold worked and precipitations hardened or solution annealed plus precipitation hardened and descaled conditions. When atmosphere control is used, descaling is not necessary. 1.3x00a0;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.
信息：ICS：23.040.15 CCS：发布：2015 实施：

ASTM B637-2012e1 中等或较高温度作业用沉淀硬化镍合金棒材、锻件及锻坯标准规格
简介：1.1 This specification2 covers hot- and cold-worked precipitation-hardenable nickel alloy rod, bar, forgings, and forging stock for moderate or high temperature service (Table 1).TABLE 1 Chemical Requirements Element Composition Limits, % UNS N07022 UNS N07208 UNS N07252 (Formerly Grade 689) UNS N07001 (Formerly Grade 685) UNS N07500 (Formerly Grade 684) UNS N07750 (Formerly Grade 688) UNS N07718 (Formerly Grade 718) Carbon 0.010 max 0.04???0.08 0.10???0.20 0.03???0.10 0.15 max 0.08 max 0.08 max
信息：ICS：77.150.40 (Nickel and chromium products) CCS：H62 发布：2012 实施：