ISO 1179检测标准

发布时间：2023-02-07 11:51:55 • 阅读量： • 来源：中析研究所

ISO 1179相关标准参考信息

ISO 1179-2-2022 通用和流体动力连接件.带ISO 228-1螺纹的弹性体或金属对金属密封的端口和螺柱端头.第2部分:带弹性体密封的重型（S系列）和轻型（L系列）螺柱端（E型）
简介：
信息：ICS：23.100.40 CCS：发布：2022-11-10 实施：

BS EN ISO 1179-1-2009
简介：
信息：ICS：23.100.40 CCS：发布：2009-02-28 实施：2009-02-28

ISO 1179-2:2007 通用和流体动力连接件.带ISO 228-1弹性或金属对金属密封螺纹的端口和螺柱端.第2部分:带弹性密封的重型（S系列）和轻型（L系列）螺柱端（E型）
简介：
信息：ICS：23.100.40 CCS：发布：2007-08-13 实施：

DIN EN ISO 1179-1-2014 液体传动通用连接件. 带弹性体密封或金属对金属密封的ISO 228-1螺纹孔口和螺柱端. 第1部分: 带螺纹的孔口(ISO 1179-1-2013); 德文版本EN ISO 1179-1-2013
简介：
信息：ICS：23.100.40 CCS：J15 发布：2014-03 实施：

BS EN ISO 1179-3-2009
简介：
信息：ICS：23.100.40 CCS：发布：2009-02-28 实施：2009-02-28

ISO 1179-3:2007 通用和流体动力连接件——带ISO 228-1弹性体或金属对金属密封螺纹的端口和螺柱端第3部分:带挡圈的O形圈密封的轻型（L系列）螺柱端（G型和H型）
简介：
信息：ICS：23.100.40 CCS：发布：2007-08-13 实施：

DIN EN ISO 1179-2-2014 一般用途和液压传动的连接件. 带有合成橡胶或金属对金属密封的ISO 228-1螺纹端口和螺柱端. 第2部分:重型 (S系列) 和轻型 (L系列) 带合成橡胶密封的螺柱端 (E型) (ISO 1179-2-2013); 德文版本EN ISO 1179-2-2013
简介：
信息：ICS：23.100.40 CCS：J20 发布：2014-03 实施：

DIN EN ISO 1179-1-2008 通用和液压传动用连接件.带弹性体密封或金属对金属密封的ISO 228-1螺纹的孔口和螺柱端.第1部分:带螺纹的孔口
简介：This part of ISO 1179 specifies dimensions for ports with ISO 228-1 threads for use with non-adjustable stud ends shown in ISO 1179-2, ISO 1179-3 and ISO 1179-4 and with adjustable stud ends shown in ISO 1179-3. Ports in accordance with this part of ISO 1179 may be used: with ISO 1179-2 heavy-duty (S series) stud ends with type E sealing at working pressures up to 63 MPa (630 bar) and light-duty (L series) stud ends at working pressures up to 25 MPa (250 bar); with ISO 1179-3 light-duty (L series) stud ends with type G sealing at working pressures up to 31,5 MPa (315 bar), and with ISO 1179-3 light-duty (L series) adjustable stud ends with type H sealing at working pressures up to 20 MPa (200 bar);-- with ISO 1179-4 stud ends with type B sealing at working pressures up to 40 MPa (400 bar) for the S series, up to 25 MPa (250 bar) for the L series, and up to 10 MPa (100 bar) for the LL series,except for the G2 size port, which in hydraulic fluid power systems is used mainly with accumulators and forwhich ISO 1179-2, ISO 1179-3 and ISO 1179-4 do not specify stud ends. The permissible working pressuredepends upon size, materials, design, working conditions, application, etc.Users of this part of ISO 1179 should ensure that there is sufficient material around the port to maintain thepressure.NOTE The introduction of this part of ISO 1179 gives recommendations for ports and stud ends to be used for newdesigns in hydraulic and pneumatic fluid power applications.
信息：ICS：23.100.40 CCS：J15 发布：2008-08-01 实施：

ISO 1179-2-2007 通用和液压传动用连接件.带弹性体密封件或金属对金属密封件的ISO 228-1螺纹开口和螺柱端头.第2部分:带弹性体密封件(E型)的重型(S系列)和轻型(L系列)螺柱端头
简介：This part of ISO 1179 specifies dimensions, performance requirements and test procedures for heavy-duty(S series) and light-duty (L series) stud ends with ISO 228-1 threads and the elastomeric sealing (type E) thatis used with them.Heavy-duty (S series) stud ends with type E sealing in accordance with this part of ISO 1179 may be used atworking pressures up to 63 MPa (630 bar). Light-duty (L series) stud ends with type E sealing in accordancewith this part of ISO 1179 may be used at working pressures up to 25 MPa (250 bar). The permissible workingpressure depends upon size, materials, design, working conditions, application, etc.Conformance to the dimensional information in this part of ISO 1179 does not guarantee rated performance.Each manufacturer shall perform testing according to the specification contained in this part of ISO 1179 toassure that components made to this part of ISO 1179 comply with the performance ratings.NOTE 1 This part of ISO 1179 applies to connectors detailed in ISO 8434-1 and ISO 8434-2.NOTE 2 The introduction of this part of ISO 1179 gives recommendations for ports and stud ends to be used for newdesigns in hydraulic and pneumatic fluid power applications
信息：ICS：23.100.40 CCS：J15 发布：2007-08 实施：

BS EN ISO 1179-2-2013 通用和液压传动用连接件.带弹性体密封件或金属对金属密封件的ISO 228-1标准螺纹端口或螺柱端头.带弹性体密封件(E型)的重型(S系列)和轻型(L系列)螺柱端头
简介：
信息：ICS：23.100.40 CCS：J20 发布：2013-11-30 实施：2013-11-30

DIN EN ISO 1179-2-2008 通用和液压传动用连接件.带弹性体密封或金属对金属密封的ISO 228-1螺纹的孔口和螺柱端.第2部分:带弹性体密封(E型)的重型(S系列)和轻型(L系列)螺柱端
简介：This part of ISO 1179 specifies dimensions, performance requirements and test procedures for heavy-duty(S series) and light-duty (L series) stud ends with ISO 228-1 threads and the elastomeric sealing (type E) thatis used with them.Heavy-duty (S series) stud ends with type E sealing in accordance with this part of ISO 1179 may be used atworking pressures up to 63 MPa (630 bar). Light-duty (L series) stud ends with type E sealing in accordancewith this part of ISO 1179 may be used at working pressures up to 25 MPa (250 bar). The permissible workingpressure depends upon size, materials, design, working conditions, application, etc.Conformance to the dimensional information in this part of ISO 1179 does not guarantee rated performance.Each manufacturer shall perform testing according to the specification contained in this part of ISO 1179 toassure that components made to this part of ISO 1179 comply with the performance ratings.NOTE 1 This part of ISO 1179 applies to connectors detailed in ISO 8434-1 and ISO 8434-2.NOTE 2 The introduction of this part of ISO 1179 gives recommendations for ports and stud ends to be used for newdesigns in hydraulic and pneumatic fluid power applications.
信息：ICS：23.100.40 CCS：J15 发布：2008-08-01 实施：

ISO 1179-4-2007 通用和液压传动用连接件.带弹性体密封件或金属对金属密封件的ISO 228-1螺纹开口和螺柱端头.第4部分:通用只带金属对金属密封件(B型)的螺柱端头
简介：This part of ISO 1179 specifies dimensions, performance requirements and test procedures for stud ends withISO 228-1 threads and metal-to-metal sealing for general use only. These stud ends should not be used forleak-free hydraulic fluid power applications.Stud ends in accordance with this part of ISO 1179 may be used at working pressures up to 40 MPa (400 bar)for the S series, up to 25 MPa (250 bar) for the L series, and up to 10 MPa (100 bar) for the LL series. Thepermissible working pressure depends upon size, materials, design, working conditions, application, etc.Conformance to the dimensional information in this part of ISO 1179 does not guarantee rated performance.Each manufacturer shall perform tests according to the specification contained in this part of ISO 1179 inorder to ensure that components made to this part of ISO 1179 comply with the performance ratings.NOTE 1 This part of ISO 1179 applies to connectors detailed in ISO 8434-1 and ISO 8434-2.NOTE 2 The introduction of this part of ISO 1179 gives recommendations for ports and stud ends to be used for newdesigns in hydraulic and pneumatic fluid power applications.
信息：ICS：23.100.40 CCS：J15 发布：2007-08 实施：

BS EN ISO 1179-1-2013 通用和液压传动用连接件.带弹性体密封或金属对金属密封的ISO 228-1标准螺纹的孔口和螺柱端.带螺纹的孔口
简介：
信息：ICS：23.100.40 CCS：J15 发布：2013-11-30 实施：2013-11-30

DIN EN ISO 1179-3-2008 通用和液压传动用连接件.带弹性体密封或金属对金属密封的ISO 228-1螺纹的孔口和螺柱端.第3部分:带定位环(G和H型)O型密封圈密封的轻型(L系列)螺柱端
简介：This part of ISO 1179 specifies dimensions, performance requirements and test procedures for non-adjustableand adjustable light-duty (L series) stud ends with ISO 228-1 threads with sealing by O-ring with retaining ring(types G and H, respectively).Light-duty (L series) stud ends in accordance with this part of ISO 1179 may be used at working pressures upto 31,5 MPa (315 bar) for non-adjustable stud ends (type G) and up to 20 MPa (200 bar) for adjustable studends (type H). The permissible working pressure depends upon size, materials, design, working conditions,application, etc.Conformance to the dimensional information in this part of ISO 1179 does not guarantee rated performance.Each manufacturer shall perform testing according to the specification contained in this part of ISO 1179 toassure that components made to this part of ISO 1179 comply with the performance ratings.NOTE I This part of ISO 1179 applies to connectors detailed in ISO 8434-2.NOTE 2 The introduction of this part of ISO 1179 gives recommendations for ports and stud ends to be used for newdesigns in hydraulic and pneumatic fluid power applications.
信息：ICS：23.100.40 CCS：J15 发布：2008-08-01 实施：

ISO 1179-1-2007 通用和液压传动用连接件.带弹性体密封件或金属对金属密封件的ISO 228-1螺纹开口和螺柱端头.第1部分:螺纹开口
简介：This part of ISO 1179 specifies dimensions for ports with ISO 228-1 threads for use with non-adjustable studends shown in ISO 1179-2, ISO 1179-3 and ISO 1179-4 and with adjustable stud ends shown in ISO 1179-3.Ports in accordance with this part of ISO 1179 may be used:with ISO 1179-2 heavy-duty (S series) stud ends with type E sealing at working pressures up to 63 MPa(630 bar) and light-duty (L series) stud ends at working pressures up to 25 MPa (250 bar);with ISO 1179-3 light-duty (L series) stud ends with type G sealing at working pressures up to 31,5 MPa(315 bar), and with ISO 1179-3 light-duty (L series) adjustable stud ends with type H sealing at workingpressures up to 20 MPa (200 bar);with ISO 1179-4 stud ends with type B sealing at working pressures up to 40 MPa (400 bar) for the Sseries, up to 25 MPa (250 bar) for the L series, and up to 10 MPa (100 bar) for the LL series,except for the G2 size port, which in hydraulic fluid power systems is used mainly with accumulators and forwhich ISO 1179-2, ISO 1179-3 and ISO 1179-4 do not specify stud ends. The permissible working pressuredepends upon size, materials, design, working conditions, application, etc.Users of this part of ISO 1179 should ensure that there is sufficient material around the port to maintain thepressure.NOTE The introduction of this part of ISO 1179 gives recommendations for ports and stud ends to be used for newdesigns in hydraulic and pneumatic fluid power applications.
信息：ICS：23.100.40 CCS：J15 发布：2007-08 实施：

ISO 1179-2-2013 通用和液压传动用连接件.带弹性体密封件或金属对金属密封件的ISO 228-1标准螺纹开口和螺柱端头.第2部分:带弹性体密封件(E型)的重型(S系列)和轻型(L系列)螺柱端头
简介：This part of ISO 1179 specifies dimensions, performance requirements and test procedures for heavy-duty (S series) and light-duty (L series) stud ends with ISO 228-1 threads and the elastomeric sealing (type E) that is used with them.
信息：ICS：23.100.40 CCS：J20 发布：2013-11 实施：

DIN EN ISO 1179-4-2008 通用和液压传动用连接件.带弹性体密封或金属对金属密封的ISO 228-1螺纹的孔口和螺柱端.第4部分:仅与金属对金属密封(B型)的通用螺柱端
简介：This part of ISO 1179 specifies dimensions, performance requirements and test procedures for stud ends with ISO 228-1 threads and metal-to-metal sealing for general use only. These stud ends should not be used forleak-free hydraulic fluid power applications.Stud ends in accordance with this part of ISO 1179 may be used at working pressures up to 40 MPa (400 bar)for the S series, up to 25 MPa (250 bar) for the L series, and up to 10 MPa (100 bar) for the LL series. Thepermissible working pressure depends upon size, materials, design, working conditions, application, etc.Conformance to the dimensional information in this part of ISO 1179 does not guarantee rated performance.Each manufacturer shall perform tests according to the specification contained in this part of ISO 1179 inorder to ensure that components made to this part of ISO 1179 comply with the performance ratings.NOTE 1 This part of ISO 1179 applies to connectors detailed in ISO 8434-1 and ISO 8434-2.NOTE 2 The introduction of this part of ISO 1179 gives recommendations for ports and stud ends to be used for newdesigns in hydraulic and pneumatic fluid power applications.
信息：ICS：23.100.40 CCS：J15 发布：2008-08-01 实施：

ISO 1179-3-2007 通用和液压传动用连接件.带弹性体密封件或金属对金属密封件的ISO 228-1螺纹开口和螺柱端头.第3部分:带扣环O型密封圈(G型和H型)密封的轻型(L系列)螺柱端头
简介：This part of ISO 1179 specifies dimensions, performance requirements and test procedures for non-adjustableand adjustable light-duty (L series) stud ends with ISO 228-1 threads with sealing by O-ring with retaining ring(types G and H, respectively).Light-duty (L series) stud ends in accordance with this part of ISO 1179 may be used at working pressures upto 31,5 MPa (315 bar) for non-adjustable stud ends (type G) and up to 20 MPa (200 bar) for adjustable studends (type H). The permissible working pressure depends upon size, materials, design, working conditions,application, etc.Conformance to the dimensional information in this part of ISO 1179 does not guarantee rated performance.Each manufacturer shall perform testing according to the specification contained in this part of ISO 1179 toassure that components made to this part of ISO 1179 comply with the performance ratings.NOTE 1 This part of ISO 1179 applies to connectors detailed in ISO 8434-2.NOTE 2 The introduction of this part of ISO 1179 gives recommendations for ports and stud ends to be used for newdesigns in hydraulic and pneumatic fluid power applications.
信息：ICS：23.100.40 CCS：J15 发布：2007-08 实施：

ISO 1179-1-2013 通用和液压传动用连接件.带弹性体密封或金属对金属密封的ISO 228-1标准螺纹的孔口和螺柱端.第1部分:带螺纹的孔口
简介：This part of ISO 1179 specifies dimensions for ports with ISO 228-1 threads for use with non-adjustable stud ends described in ISO 1179-2, ISO 1179-3 and ISO 1179-4 and with adjustable stud ends described in ISO 1179-3.
信息：ICS：23.100.40 CCS：J15 发布：2013-11 实施：

LST EN ISO 1179-4-2008
简介：
信息：ICS：23.100.40 CCS：发布：2008-07-29 实施：2008-07-29

ISO/TS 10303-1179-2005 工业自动化系统和集成.产品数据表示和交换.第1179部分:应用模块:个体行为包含
简介：ISO/TS 10303-1179:2005 specifies the application module for Individual involvement in activity. The following are within the scope of ISO/TS 10303-1179:2005: a individual product, document, person, organization or other activity that is involved in an individual activity.
信息：ICS：35.240.50 CCS：N18 发布：2005-11 实施：

ISO 1179-1:2013 通用和流体动力连接件——带ISO 228-1弹性体或金属对金属密封螺纹的端口和螺柱端第1部分:螺纹端口
简介：
信息：ICS：23.100.40 CCS：发布：2013-10-22 实施：

LST EN ISO 1179-3-2008
简介：
信息：ICS：23.100.40 CCS：发布：2008-07-29 实施：2008-07-29

ISO 1179:1981 符合ISO 228/1的螺纹管接头用于工业应用中的平端钢和其他金属管
简介：
信息：ICS：23.100.40 CCS：发布：1981-10-01 实施：

ISO 1179-2:2013 通用和流体动力连接件——带ISO 228-1弹性或金属对金属密封螺纹的端口和螺柱端第2部分:带弹性密封的重型（S系列）和轻型（L系列）螺柱端（E型）
简介：
信息：ICS：23.100.40 CCS：发布：2013-10-22 实施：

LST EN ISO 1179-2-2008
简介：
信息：ICS：23.100.40 CCS：发布：2008-07-29 实施：2008-07-29

ISO 1179-1981 符合ISO 228/1螺纹的工业用平端钢管和其他金属管接头
简介：This second edition cacncels replaces the first edition (1973). Establishes a limited range of threads for connenction of tubes to machines or equipment and indicates the related outside diameters of the tubes. The outside diameters ranging from 4 mm up to and including 50 mm.
信息：ICS：21.040.20 CCS：J15 发布：1981-10 实施：

EN ISO 1179-2-2013
简介：Dieser Teil von ISO 1179 legt Mase, Leistungsanforderungen und Prufverfahren fur Einschraubzapfen der schweren Reihe (S-Reihe) und der leichten Reihe (L-Reihe) mit Gewinde nach ISO 228-1 und Elastomerdichtung (Form E) fest. Einschraubzapfen der schweren Reihe (S-Reihe) mit Dichtung der Form E, die diesem Teil von ISO 1179 entsprechen, konnen bei Arbeitsdrucken bis 63 MPa (630 bar) eingesetzt werden. Einschraubzapfen der leichten Reihe (L-Reihe) mit Dichtung der Form E, die diesem Teil von ISO 1179 entsprechen, konnen bei Arbeitsdrucken bis 25 MPa (250 bar) eingesetzt werden. Der zulassige Arbeitsdruck ist von Grose, Werkstoffen, Konstruktion, Betriebsbedingungen, Anwendung, usw. abhangig. Ubereinstimmung mit den Masangaben in diesem Teil von ISO 1179 garantiert keine Nennleistung. Es liegt in der Verantwortung jedes Herstellers, Prufungen entsprechend den Festlegungen dieses Teils von ISO 1179 durchfuhren, um sicherzustellen, dass die nach diesem Teil von ISO 1179 hergestellten Bauteile mit den Nennleistungen ubereinstimmen. ANMERKUNG 1 Dieser Teil von ISO 1179 gilt fur Verschraubungen nach ISO 8434-1 und ISO 8434-2. ANMERKUNG 2 Die Einleitung dieses Teils von ISO 1179 enthalt Empfehlungen fur Einschraublocher und -zapfen fur Neukonstruktionen in hydraulischen und pneumatischen Kraftubertragungsanlagen.
信息：ICS：23.100.40 CCS：发布：2013 实施：

LST EN ISO 1179-1-2008
简介：
信息：ICS：23.100.40 CCS：发布：2008-07-29 实施：2008-07-29

ISO 1179:1973 标题缺失-遗留纸质文档
简介：
信息：ICS： CCS：发布：1973-01-01 实施：

EN ISO 1179-2-2013 通用和液压传动用连接件.带弹性体密封或金属对金属密封的ISO 228-1标准螺纹的端口和螺柱端.第2部分:带弹性体密封件(E型)的重型(S系列)和轻型(L系列)螺柱端头
简介：Dieser Teil von ISO 1179 legt Mase, Leistungsanforderungen und Prufverfahren fur Einschraubzapfen der schweren Reihe (S-Reihe) und der leichten Reihe (L-Reihe) mit Gewinde nach ISO 228-1 und Elastomerdichtung (Form E) fest. Einschraubzapfen der schweren Reihe (S-Reihe) mit Dichtung der Form E, die diesem Teil von ISO 1179 entsprechen, konnen bei Arbeitsdrucken bis 63 MPa (630 bar) eingesetzt werden. Einschraubzapfen der leichten Reihe (L-Reihe) mit Dichtung der Form E, die diesem Teil von ISO 1179 entsprechen, konnen bei Arbeitsdrucken bis 25 MPa (250 bar) eingesetzt werden. Der zulassige Arbeitsdruck ist von Grose, Werkstoffen, Konstruktion, Betriebsbedingungen, Anwendung, usw. abhangig. Ubereinstimmung mit den Masangaben in diesem Teil von ISO 1179 garantiert keine Nennleistung. Es liegt in der Verantwortung jedes Herstellers, Prufungen entsprechend den Festlegungen dieses Teils von ISO 1179 durchfuhren, um sicherzustellen, dass die nach diesem Teil von ISO 1179 hergestellten Bauteile mit den Nennleistungen ubereinstimmen. ANMERKUNG 1 Dieser Teil von ISO 1179 gilt fur Verschraubungen nach ISO 8434-1 und ISO 8434-2. ANMERKUNG 2 Die Einleitung dieses Teils von ISO 1179 enthalt Empfehlungen fur Einschraublocher und -zapfen fur Neukonstruktionen in hydraulischen und pneumatischen Kraftubertragungsanlagen.
信息：ICS：23.100.40 CCS：J15 发布：2013 实施：2013

DS/EN ISO 1179-1-2008
简介：This part of ISO 1179 specifies dimensions for ports with ISO 228-1 threads for use with non-adjustable stud ends shown in ISO 1179-2, ISO 1179-3 and ISO 1179-4 and with adjustable stud ends shown in ISO 1179-3.Ports in accordance with this part of ISO 1179 may be used:. with ISO 1179-2 heavy-duty (S series) stud ends with type E sealing at working pressures up to 63 MPa (630 bar) and light-duty (L series) stud ends at working pressures up to 25 MPa (250 bar);. with ISO 1179-3 light-duty (L series) stud ends with type G sealing at working pressures up to 31,5 MPa (315 bar), and with ISO 1179-3 light-duty (L series) adjustable stud ends with type H sealing a
信息：ICS：23.100.40 CCS：发布：2008-06-06 实施：2008-06-06

ISO 1179-1973 标题缺失-遗留纸质文档
简介：
信息：ICS： CCS：发布：1973-01-01 实施：

EN ISO 1179-1-2013
简介：Dieser Teil von ISO 1179 legt die Mase fur Einschraublocher mit Gewinde nach ISO 228-1 fur den Einsatz mit nicht richtungseinstellbaren Einschraubzapfen nach ISO 1179-2, ISO 1179-3 und ISO 1179-4 sowie mit richtungseinstellbaren Einschraubzapfen nach ISO 1179-3 fest. Einschraublocher, die diesem Teil von ISO 1179 entsprechen, durfen verwendet werden mit Einschraubzapfen der schweren Reihe (S-Reihe) mit Dichtung der Form E bei Arbeitsdrucken bis 63 MPa (630 bar) und Einschraubzapfen der leichten Reihe (L-Reihe) bei Arbeitsdrucken bis 25 MPa (250 bar) nach ISO 1179-2, Einschraubzapfen der leichten Reihe (L-Reihe) mit Dichtung der Form G bei Arbeitsdrucken bis 31,5 MPa (315 bar) nach ISO 1179-3 und richtungseinstellbaren Einschraubzapfen der leichten Reihe (L-Reihe) mit Dichtung der Form H bei Arbeitsdrucken bis 20 MPa (200 bar) nach ISO 1179-3, und Einschraubzapfen mit Dichtung der Form B bei Arbeitsdrucken bis 40 MPa (400 bar) fur die S-Reihe, bis 25 MPa (250 bar) fur die L-Reihe und bis 10 MPa (100 bar) fur die LL-Reihe nach ISO 1179-4. Ausgenommen sind G2-Einschraublocher, die in hydraulischen Kraftubertragungsanlagen hauptsachlich mit Druckspeichern eingesetzt werden und fur die in ISO 1179-3 und ISO 1179-4 keine Einschraubzapfen festgelegt sind. Der zulassige Arbeitsdruck ist von Grose, Werkstoffen, Konstruktion, Betriebsbedingungen, Anwendung usw. abhangig. Anwender dieses Teils von ISO 1179 sollten sicherstellen, dass der Werkstoff um das Einschraubloch fur die Beibehaltung des Druckes ausreicht. ANMERKUNG Die Einleitung dieses Teils von ISO 1179 enthalt Empfehlungen fur Einschraublocher und -zapfen fur Neukonstruktionen in hydraulischen und pneumatischen Kraftubertragungsanlagen.
信息：ICS：23.100.40 CCS：发布：2013 实施：

DS/EN ISO 1179-2-2008
简介：This part of ISO 1179 specifies dimensions, performance requirements and test procedures for heavy-duty (S series) and light-duty (L series) stud ends with ISO 228-1 threads and the elastomeric sealing (type E) that is used with them.Heavy-duty (S series) stud ends with type E sealing in accordance with this part of ISO 1179 may be used at working pressures up to 63 MPa (630 bar). Light-duty (L series) stud ends with type E sealing in accordance with this part of ISO 1179 may be used at working pressures up to 25 MPa (250 bar). The permissible working pressure depends upon size, materials, design, working conditions, application, etc. Conformance to the dim
信息：ICS：23.100.40 CCS：发布：2008-06-06 实施：2008-06-06

ISO/R 1179-1970 标题缺失-遗留纸质文档
简介：
信息：ICS： CCS：发布：1970-01-01 实施：

EN ISO 1179-1-2013 通用和液压传动用连接件.带弹性体密封或金属对金属密封的ISO 228-1标准螺纹的端口和螺柱端.第1部分:带螺纹端口
简介：Dieser Teil von ISO 1179 legt die Mase fur Einschraublocher mit Gewinde nach ISO 228-1 fur den Einsatz mit nicht richtungseinstellbaren Einschraubzapfen nach ISO 1179-2, ISO 1179-3 und ISO 1179-4 sowie mit richtungseinstellbaren Einschraubzapfen nach ISO 1179-3 fest. Einschraublocher, die diesem Teil von ISO 1179 entsprechen, durfen verwendet werden mit Einschraubzapfen der schweren Reihe (S-Reihe) mit Dichtung der Form E bei Arbeitsdrucken bis 63 MPa (630 bar) und Einschraubzapfen der leichten Reihe (L-Reihe) bei Arbeitsdrucken bis 25 MPa (250 bar) nach ISO 1179-2, Einschraubzapfen der leichten Reihe (L-Reihe) mit Dichtung der Form G bei Arbeitsdrucken bis 31,5 MPa (315 bar) nach ISO 1179-3 und richtungseinstellbaren Einschraubzapfen der leichten Reihe (L-Reihe) mit Dichtung der Form H bei Arbeitsdrucken bis 20 MPa (200 bar) nach ISO 1179-3, und Einschraubzapfen mit Dichtung der Form B bei Arbeitsdrucken bis 40 MPa (400 bar) fur die S-Reihe, bis 25 MPa (250 bar) fur die L-Reihe und bis 10 MPa (100 bar) fur die LL-Reihe nach ISO 1179-4. Ausgenommen sind G2-Einschraublocher, die in hydraulischen Kraftubertragungsanlagen hauptsachlich mit Druckspeichern eingesetzt werden und fur die in ISO 1179-3 und ISO 1179-4 keine Einschraubzapfen festgelegt sind. Der zulassige Arbeitsdruck ist von Grose, Werkstoffen, Konstruktion, Betriebsbedingungen, Anwendung usw. abhangig. Anwender dieses Teils von ISO 1179 sollten sicherstellen, dass der Werkstoff um das Einschraubloch fur die Beibehaltung des Druckes ausreicht. ANMERKUNG Die Einleitung dieses Teils von ISO 1179 enthalt Empfehlungen fur Einschraublocher und -zapfen fur Neukonstruktionen in hydraulischen und pneumatischen Kraftubertragungsanlagen.
信息：ICS：23.100.40 CCS：J15 发布：2013 实施：2013

DS/EN ISO 1179-3-2008
简介：This part of ISO 1179 specifies dimensions, performance requirements and test procedures for non-adjustable and adjustable light-duty (L series) stud ends with ISO 228-1 threads with sealing by O-ring with retaining ring (types G and H, respectively).Light-duty (L series) stud ends in accordance with this part of ISO 1179 may be used at working pressures up to 31,5 MPa (315 bar) for non-adjustable stud ends (type G) and up to 20 MPa (200 bar) for adjustable stud ends (type H). The permissible working pressure depends upon size, materials, design, working conditions, application, etc.Conformance to the dimensional information in this part of ISO 1179 does no
信息：ICS：23.100.40 CCS：发布：2008-06-06 实施：2008-06-06

简介： 信息：

GOST R ISO/TS 10303-1179-2012 工业自动化系统和集成. 产品数据表示和交换. 第1179部分. 应用模块. 应用模块. 个体行为参与
简介：
信息：ICS：35.240.50 CCS：发布：2012 实施：2013-07-01

DS/EN ISO 1179-4-2008
简介：This part of ISO 1179 specifies dimensions, performance requirements and test procedures for stud ends with ISO 228-1 threads and metal-to-metal sealing for general use only. These stud ends should not be used for leak-free hydraulic fluid power applications.Stud ends in accordance with this part of ISO 1179 may be used at working pressures up to 40 MPa (400 bar) for the S series, up to 25 MPa (250 bar) for the L series, and up to 10 MPa (100 bar) for the LL series. The permissible working pressure depends upon size, materials, design, working conditions, application, etc.Conformance to the dimensional information in this part of ISO 1179 does not guarantee
信息：ICS：23.100.40 CCS：发布：2008-06-06 实施：2008-06-06

简介： 信息：

BS EN ISO 1179-3-2008 通用和液压传动用连接件.带弹性体密封件或金属对金属密封件的ISO 228-1螺纹端口和螺柱端头.带扣环O型密封圈(G型和H型)密封的轻型(L系列)螺柱端头
简介：This part of ISO 1179 specifies dimensions, performance requirements and test procedures for non-adjustableand adjustable light-duty (L series) stud ends with ISO 228-1 threads with sealing by O-ring with retaining ring(types G and H, respectively).Light-duty (L series) stud ends in accordance with this part of ISO 1179 may be used at working pressures upto 31,5 MPa (315 bar) for non-adjustable stud ends (type G) and up to 20 MPa (200 bar) for adjustable studends (type H). The permissible working pressure depends upon size, materials, design, working conditions,application, etc.Conformance to the dimensional information in this part of ISO 1179 does not guarantee rated performance.Each manufacturer shall perform testing according to the specification contained in this part of ISO 1179 toassure that components made to this part of ISO 1179 comply with the performance ratings.
信息：ICS：23.100.40 CCS：J10 发布：2009-02-28 实施：2009-02-28

EN ISO 1179-1-2008 通用和液压传动用连接件.带弹性体密封或金属对金属密封的ISO 228-1螺纹的孔口和螺柱端.第1部分:带螺纹的孔口
简介：This part of ISO 1179 specifies dimensions for ports with ISO 228-1 threads for use with non-adjustable stud ends shown in ISO 1179-2; ISO 1179-3 and ISO 1179-4 and with adjustable stud ends shown in ISO 1179-3.
信息：ICS：23.100.40 CCS：发布：2008-04-01 实施：

简介： 信息：

BS EN ISO 1179-4-2008 通用和液压传动用连接件.带弹性体密封件或金属对金属密封件的ISO 228-1螺纹端口和螺柱端头.通用只带金属对金属密封件(B型)的螺柱端头
简介：This part of ISO 1179 specifies dimensions, performance requirements and test procedures for stud ends withISO 228-1 threads and metal-to-metal sealing for general use only. These stud ends should not be used forleak-free hydraulic fluid power applications.Stud ends in accordance with this part of ISO 1179 may be used at working pressures up to 40 MPa (400 bar)for the S series, up to 25 MPa (250 bar) for the L series, and up to 10 MPa (100 bar) for the LL series. Thepermissible working pressure depends upon size, materials, design, working conditions, application, etc.Conformance to the dimensional information in this part of ISO 1179 does not guarantee rated performance.Each manufacturer shall perform tests according to the specification contained in this part of ISO 1179 inorder to ensure that components made to this part of ISO 1179 comply with the performance ratings.
信息：ICS：23.100.40 CCS：J15 发布：2009-02-28 实施：2009-02-28

EN ISO 1179-2-2008 通用和液压传动用连接件.带弹性体密封或金属对金属密封的ISO 228-1螺纹的孔口和螺柱端.第2部分:带弹性体密封(E型)的重型(S系列)和轻型(L系列)螺柱端
简介：This part of ISO 1179 specifies dimensions; performance requirements and test procedures for heavy-duty (S series) and light-duty (L series) stud ends with ISO 228-1 threads and the elastomeric sealing (type E) that is used with them.
信息：ICS：23.100.40 CCS：发布：2008-04-01 实施：

简介： 信息：

BS EN ISO 1179-2-2008 通用和液压传动用连接件.带弹性体密封件或金属对金属密封件的ISO 228-1螺纹端口或螺柱端头.带弹性体密封件(E型)的重型(S系列)和轻型(L系列)螺柱端头
简介：This part of ISO 1179 specifies dimensions, performance requirements and test procedures for heavy-duty(S series) and light-duty (L series) stud ends with ISO 228-1 threads and the elastomeric sealing (type E) thatis used with them.Heavy-duty (S series) stud ends with type E sealing in accordance with this part of ISO 1179 may be used atworking pressures up to 63 MPa (630 bar). Light-duty (L series) stud ends with type E sealing in accordancewith this part of ISO 1179 may be used at working pressures up to 25 MPa (250 bar). The permissible workingpressure depends upon size, materials, design, working conditions, application, etc.Conformance to the dimensional information in this part of ISO 1179 does not guarantee rated performance.Each manufacturer shall perform testing according to the specification contained in this part of ISO 1179 toassure that components made to this part of ISO 1179 comply with the performance ratings.
信息：ICS：23.100.40 CCS：J15 发布：2009-02-28 实施：2009-02-28

EN ISO 1179-3-2008 通用和液压传动用连接件.带弹性体密封或金属对金属密封的ISO 228-1螺纹的孔口和螺柱端.第3部分:带定位环(G和H型)O型密封圈密封的轻型(L系列)螺柱端
简介：This part of ISO 1179 specifies dimensions; performance requirements and test procedures for non-adjustable and adjustable light-duty (L series) stud ends with ISO 228-1 threads with sealing by O-ring with retaining ring (types G and H; respectively).
信息：ICS：23.100.40 CCS：发布：2008-04-01 实施：

简介： 信息：

BS EN ISO 1179-1-2008 通用和液压传动用连接件.带弹性体密封件或金属对金属密封件的ISO 228-1螺纹端口和螺柱端头.螺纹端口
简介：This part of ISO 1179 specifies dimensions for ports with ISO 228-1 threads for use with non-adjustable studends shown in ISO 1179-2, ISO 1179-3 and ISO 1179-4 and with adjustable stud ends shown in ISO 1179-3.Ports in accordance with this part of ISO 1179 may be used:? with ISO 1179-2 heavy-duty (S series) stud ends with type E sealing at working pressures up to 63 MPa(630 bar) and light-duty (L series) stud ends at working pressures up to 25 MPa (250 bar);? with ISO 1179-3 light-duty (L series) stud ends with type G sealing at working pressures up to 31,5 MPa(315 bar), and with ISO 1179-3 light-duty (L series) adjustable stud ends with type H sealing at workingpressures up to 20 MPa (200 bar);? with ISO 1179-4 stud ends with type B sealing at working pressures up to 40 MPa (400 bar) for the Sseries, up to 25 MPa (250 bar) for the L series, and up to 10 MPa (100 bar) for the LL series,except for the G2 size port, which in hydraulic fluid power systems is used mainly with accumulators and forwhich ISO 1179-2, ISO 1179-3 and ISO 1179-4 do not specify stud ends. The permissible working pressuredepends upon size, materials, design, working conditions, application, etc.Users of this part of ISO 1179 should ensure that there is sufficient material around the port to maintain thepressure.
信息：ICS：23.100.40 CCS：J15 发布：2009-02-28 实施：2009-02-28

EN ISO 1179-4-2008 通用和液压传动用连接件.带弹性体密封或金属对金属密封的ISO 228-1螺纹的孔口和螺柱端.第4部分:仅与金属对金属密封(B型)的通用螺柱端
简介：This part of ISO 1179 specifies dimensions; performance requirements and test procedures for stud ends with ISO 228-1 threads and metal-to-metal sealing for general use only. These stud ends should not be used for leak-free hydraulic fluid power applications.
信息：ICS：23.100.40 CCS：发布：2008-04-01 实施：

简介： 信息：

BS EN ISO 1179-1-2009
简介：
信息：ICS：23.100.40 CCS：发布：2009-02-28 实施：2009-02-28

ISO 1179-1:2007 通用和流体动力连接件.带ISO 228-1弹性或金属对金属密封螺纹的端口和螺柱端.第1部分:螺纹端口
简介：
信息：ICS：23.100.40 CCS：发布：2007-08-13 实施：

简介： 信息：

BS EN ISO 1179-3-2009
简介：
信息：ICS：23.100.40 CCS：发布：2009-02-28 实施：2009-02-28

ISO 1179-4:2007 通用和流体动力连接件——带ISO 228-1弹性体或金属对金属密封螺纹的端口和螺柱端第4部分:仅用于金属对金属密封的通用螺柱端（B型）
简介：
信息：ICS：23.100.40 CCS：发布：2007-08-13 实施：

简介： 信息：