气密检漏仪检测标准气密检漏仪-中析研究所检测

(CMA)

(CNAS)

(ISO)

(高新技术企业)

气密检漏仪相关标准参考信息

GB/T 31473-2015 卤素气体检漏仪
简介：本标准规定了卤素气体检漏仪(以下简称检漏仪)的分类、技术要求、试验方法、检验规则以及标志、包装、运输和贮存。本标准适用于化工、制冷等行业检测卤素气体泄漏量及报警的检漏仪，不适用于质谱型检漏仪。
信息：ICS：17.020 CCS：N50 发布：2015-05-15 实施：2016-01-01

DL/T 1140-2012 电气设备六氟化硫激光检漏仪通用技术条件
简介：本标准规定了电气设备六氟化硫激光检漏仪（以下简称“SF激光检漏仪”）的基本参数、技术要求、试验方法、检验规则及铭牌、标志和使用说明书等。本标准适用于SF激光检漏仪的设计定型、生产与检验。
信息：ICS：29.020 CCS：F20 发布：2012-01-04 实施：2012-03-01

KS A 0083-2002 质谱计式检漏仪校准
简介：이 규격은 질량 분석계를 검지기로 사용하고, 그 분석관을 작동 가능한 진공 상태로 유지하기
信息：ICS：23.16 CCS：A50 发布：2002-07-04 实施：2002-07-04

GB/T 25752-2010 差压式气密检漏仪
简介：本标准规定了压差式气密检漏仪的术语和定义、分类、结构与基本参数、试验条件、试验方法、检验规则、标志、包装、运输和贮存。本标准适用于以压差传感器为感压元件检测被测物和基准物之间压力差来确定被测物是否存在泄露和漏率大小的各类压差式气密检漏仪（以下简称检漏仪）。
信息：ICS：23.160 CCS：J78 发布：2010-12-23 实施：2011-10-01

ANSI/ASHRAE 173P-2012 卤化碳制冷剂检漏仪性能测定试验方法
简介：
信息：ICS：27.200 CCS：J73 发布：2012 实施：

GB/T 13979-2008 质谱检漏仪
简介：本标准规定了质谱检漏仪（以下简称检漏仪）的要求、试验方法、检验规则、标志、包装、运输、贮存、质量保证等。本标准适用于以质谱分析法作为检测手段的检漏仪。
信息：ICS：71.040.10 CCS：N60 发布：2008-07-28 实施：2009-02-01

ASTM E493/E493M-11 在内向外测试模式下使用质谱检漏仪的泄漏标准实践
简介：
信息：ICS：19.100 CCS：发布：2011-07-01 实施：

ASTM E499-95(2000) 在探测器-探针模式下使用质谱仪检漏仪进行泄漏的标准试验方法
简介：
信息：ICS：19.100 CCS：发布：2000-07-10 实施：

GB/T 18193-2000 真空技术质谱检漏仪校准
简介：本标准规定了质谱检漏仪的校准程序。它仅适用于校准将灵敏元件处于高真空系统中的检漏仪。因此这个方法没有制订完整的验收试验。本标准规定探索气体使用氦-4。但在适当的预防措施下，可以使用其他探索气体，如氩-40。本标准的应用受到检漏仪不能测定小于10Pa·m·s漏率漏孔限制。本标准程序提出了测定最小可检漏率和最小可检浓度比的两个要点。它分别应用于高真空和压力大于一个大气压的检漏仪上。
信息：ICS：23.160 CCS：J78 发布：2000-09-26 实施：2001-02-01

ASTM E2024/E2024M-11 用热导检漏仪测量大气泄漏的标准实施规程
简介：
信息：ICS：19.100 CCS：发布：2011-07-01 实施：

ASTM E498-95(2000) 在示踪探针模式下使用质谱检漏仪或残余气体分析仪进行泄漏的标准试验方法
简介：
信息：ICS：19.100 CCS：发布：2000-07-10 实施：

GB/T 13979-1992 氦质谱检漏仪
简介：本标准规定了氦质谱检漏仪的技术要求、试验方法、检验规则和包装贮运要求。本标准适用于以氦-4做为示漏气体，以质谱分析法作为检测手段的检漏仪（以下简称仪器）。
信息：ICS：17.020 CCS：N54 发布：1992-12-17 实施：1993-07-01

ASTM E1603/E1603M-11 使用质谱检漏仪或残留气体分析仪进行泄漏测量的标准实践
简介：
信息：ICS：23.040.99 CCS：发布：2011-07-01 实施：

ASTM E427-95(2000) 用卤素检漏仪（碱离子二极管）检测泄漏的标准实施规程
简介：
信息：ICS：31.080.01 CCS：发布：2000-07-10 实施：

JJF 1986-2022 差压式气密检漏仪校准规范
简介：
信息：ICS： CCS：发布：2022-09-26 实施：2023-03-26

ASTM E498/E498M-11 在示踪探针模式下使用质谱仪检漏仪或残余气体分析仪检漏的标准实施规程
简介：
信息：ICS：19.100 CCS：发布：2011-07-01 实施：

ASTM E2024-99 用热导检漏仪测定大气泄漏的标准试验方法
简介：
信息：ICS：19.100 CCS：发布：1999-06-10 实施：

ASTM E1603/E1603M-11(2022) 在罩模式下使用质谱检漏仪或残余气体分析仪进行泄漏测量的标准实施规程
简介：
信息：ICS：23.040.99 CCS：发布：2022-06-01 实施：

HJB 399.13-2007 JL-1潜地战略导弹技术阵地保障装备修理检验验收规程第13部分：氦质谱检漏仪
简介：
信息：ICS：95.020 CCS：U30 发布：2007-04-30 实施：2007-07-01

ASTM E1603-99 用质谱仪检漏仪或罩式残余气体分析仪进行泄漏测量的标准试验方法
简介：
信息：ICS：23.040.99 CCS：发布：1999-06-10 实施：

JJF 1964-2022 卤素检漏仪校准规范
简介：
信息：ICS： CCS：XXX 发布：2022-04-29 实施：2022-10-29

ASTM D7392-2007(2013) 用于验证符合水泥厂设计和性能规格的永磁探测器和袋检漏仪制造商的标准实施规程
简介：5.1x00a0;EPA regulations require Portland cement plants that burn hazardous waste to use BLDs or PMDs to provide either a relative or an absolute indication of PM concentration and to alert the plant operator of the need to inspect PM control equipment or initiate corrective action. EPA and others have not established for these applications specific design and performance specifications for these instruments. The design and performance specifications and test procedures contained in this practice will help ensure that measurement systems are capable of providing reliable monitoring data. 5.2x00a0;This practice identifies relevant information and operational characteristics of BLD and PMD monitoring devices for Portland cement kiln systems. This practice will assist equipment suppliers and users in the evaluation and selection of appropriate monitoring equipment. 5.3x00a0;This practice requires that tests be conducted to verify manufacturerx2019;s published specifications for detection limit, linearity, thermal stability, insensitivity to supply voltage variations and other factors so that purchasers can rely on the manufacturerx2019;s published specifications. Purchasers are also assured that the specific instrument has been tested at the point of manufacture and shown to meet selected design and performance specifications prior to shipment. 5.4x00a0;This practice requires that the manufacturer develop and provide to the user written procedures for installation start-up, operation, maintenance, and quality assurance of the equipment. This practice requires that these same procedures are used for a field performance demonstration of the BLD or PMD monitoring equipment at a Portland cement plant. 5.5x00a0;The applicable test procedures and specifications of this practice are selected to address the equipment and activities that are within the control of the manufacturer. 5.6x00a0;This practice also may serve as the basis for third party independent audits of the certification procedures used by manufacturers of PMD or BLD equipment. 1.1x00a0;This practice covers the procedure for certifying particulate matter detectors (PMDs) and bag leak detectors (BLDs) that are used to monitor particulate matter (PM) emissions from kiln systems at Portland cement plants that burn hazardous waste. It includes design specifications, performance specifications, test procedures, and information requirements to ensure that these continuous monitors meet minimum requirements, necessary in part, to monitor reliably PM concentrations to indicate the need for inspection or corrective action of the types of air pollution control devices that are used at Portland cement plants that burn hazardous waste. 1.2x00a0;This practice applies specifically to the original manufacturer, or to those involved in the repair, remanufacture, or resale of PMDs or BLDs. 1.3x00a0;This practice applies to (a) wet or dry process cement kilns equipped with electrostatic precipitators, and (
信息：ICS：13.040.40 (Stationary source emissions); 91.200 (C CCS：发布：2007 实施：

SY/T 6368-1998 地下金属管道防腐层检漏仪
简介：本标准规定了地下金属管道防腐层检漏仪的组成要求、试验方法、检验规则、打击、包装、运输和贮存。本标准适用于仪器的制造、检验和质量评价
信息：ICS： CCS：E92 发布：1999-03-03 实施：1999-10-01

T/GDCKCJH 046-2021 氦质谱检漏仪性能要求与检测方法
简介：本文件规定了氦质谱检漏仪的术语和定义、性能要求及检测方法。
信息：ICS：17.120.01 CCS：M732 发布：2021-12-17 实施：2021-12-17

ASTM E498-95(2006) 在示踪探针模式下使用质谱检漏仪或残余气体分析仪进行泄漏的标准试验方法
简介：
信息：ICS：19.100 CCS：发布：2006-12-01 实施：

SAE J1628-1998 采用电子冷媒检漏仪对移动空调系统进行维修服务的技术程序
简介：This SAE Recommended Practice applies to the use of generally available electronic leak detection methods to service motor vehicle passenger compartment air conditioning systems.
信息：ICS：43.040.60 CCS：发布：1998-11-01 实施：

T/CEC 356-2020 电气设备六氟化硫红外检漏仪通用技术条件
简介：
信息：ICS： CCS：发布：2020-06-30 实施：

ASTM E499-95(2006) 在探测器-探针模式下使用质谱仪检漏仪进行泄漏的标准试验方法
简介：
信息：ICS：71.060.01 CCS：发布：2006-12-01 实施：

AIR FORCE A-A-59355-1998 氦检漏仪
简介：This Amendment forms a part of Military SpecificationMIL-S-45428D(MU)* dated 7 May 1969, and is approvedby the US Army Armament Research and DevelopmentCommand, and is available for use by all Departmentsand Agencies of the Departmen
信息：ICS： CCS：N56 发布：1998 实施：

T/CEC 356-2020 电气设备六氟化硫红外检漏仪通用技术条件
简介：本文件规定了电气设备六氟化硫红外检漏仪(以下简称检漏仪)的技术要求、试验方法、检验规则、标识和随行文件、包装、运输和贮存的要求。本文件适用于电气设备六氟化硫红外检漏仪的生产和检验。
信息：ICS：29.240.99 CCS：D4420 发布：2020-06-30 实施：2022-06-10

ASTM E493-06 用质谱仪检漏仪在内外测试模式下进行泄漏的标准试验方法
简介：
信息：ICS：19.100 CCS：发布：2006-02-01 实施：

AIR FORCE A-A-59110-1997 燃料系统检漏仪
简介：This amendment forms a part of MIL-C-50861A (AR), dated 29 March 1976, and is approved for use by the US Army Armament, Munitions, and Chemical Command, and is available for use by all Departments and Agencies of the Department of Defense.
信息：ICS：75.160.20 CCS：Q82 发布：1997-07-02 实施：

ASTM E2024/E2024M-11(2019) 用热导检漏仪测量大气泄漏的标准实施规程
简介：
信息：ICS：19.100 CCS：发布：2019-05-01 实施：

ASTM E1603-99(2006) 用质谱仪检漏仪或罩式残余气体分析仪进行泄漏测量的标准试验方法
简介：
信息：ICS：23.040.99 CCS：发布：2006-02-01 实施：

ASTM E493-97 用质谱仪检漏仪在内外测试模式下进行泄漏的标准试验方法
简介：
信息：ICS：19.100 CCS：发布：1997-01-01 实施：

DL/T 846.6-2018 高电压测试设备通用技术条件第6部分：六氟化硫气体检漏仪
简介：
信息：ICS：29.020 CCS：K60 发布：2018-12-25 实施：2019-05-01

KS R 5035-2005(2010) LPG气体检漏仪汽车
简介：
信息：ICS：43.040.30 CCS：发布：2005-12-30 实施：

ASTM F78-1997(2002) 使用副标准件校准氦检漏仪的试验方法
简介：1.1 This test method covers a procedure for calibrating a mass spectrometer-type helium leak detector with a series of commercially available calibrated leaks without need for recourse to a primary standard.1.2 Leak detector parameters determined by this test method include:1.2.1 Minimum detectable signal, drift noise (8.5, with recorder; 8.6, without recorder),1.2.2 Response time,1.2.3 Minimum detectable leak rate, and1.2.4 Sensitivity.1.3 This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：31.080.01 CCS：L41 发布：1997 实施：

ASTM E499/E499M-11(2017) 检测器探头模式下使用质谱检漏仪的泄漏标准实践
简介：
信息：ICS：71.060.01 CCS：发布：2017-06-01 实施：

GJB/J 5461-2005 数字式差压检漏仪检定规程
简介：本检定规程规定了数字式压差检漏仪（以下简称检漏仪）的检定技术要求、检定条件、检定项目、检定方法和检定结果处理及检定周期。本检定规程适用于新制造、使用中和修理后的检漏仪的检定。其他数字式检漏仪的检定也可参照使用。
信息：ICS： CCS：A53 发布：2005-12-12 实施：2006-05-01

JJG 914-1996 六氟化硫检漏仪检定规程
简介：
信息：ICS： CCS：A61 发布：1996 实施：1997-05-01

ASTM E498/E498M-11(2017) 使用质谱仪检漏仪或残留气体分析仪进行探测模式的泄漏标准实践
简介：
信息：ICS：19.100 CCS：发布：2017-06-01 实施：

ASTM E2024-05 用热导检漏仪测定大气泄漏的标准试验方法
简介：
信息：ICS：19.100 CCS：发布：2005-12-01 实施：

ASTM E427-1995(2006) 用卤素检漏仪(碱离子二极管)试验泄漏的标准实施规程
简介：Halogen leak testing can be used to indicate the presence, location and magnitude of leaks in a closed vessel. This test method is normally used for production examination. Its use with halogenated refrigerant gases has been declining because of concerns about the effect of these gases on the ozone layer.1.1 This practice covers procedures for testing and locating the sources of gas leaking at the rate of 2.2 10 14 mol/s (5 1010 Std cm3/s). The test may be conducted on any device or component across which a pressure differential of halogen tracer gas may be created, and on which the effluent side of the area to be leak tested is accessible for probing with the halogen leak detector.1.2 Five methods are described:1.2.1 Method A - Direct probing with no significant halogen contamination in the atmosphere.1.2.2 Method B - Direct probing with significant halogen contamination in the atmosphere.1.2.3 Method C - Shroud test.1.2.4 Method D - Air-curtain shroud test.1.2.5 Method E Accumulation test.1.3 The values stated in inch-pound units are to be regarded as the standard. The metric equivalents of inch-pound units may be approximate.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：31.080.01 CCS：A42 发布：1995 实施：

ASTM E493/E493M-11(2017) 在内向外测试模式下使用质谱检漏仪的泄漏标准实践
简介：
信息：ICS：19.100 CCS：发布：2017-06-01 实施：

ASTM G188-2005(2011) 黄铜和其他铜合金用检漏仪溶液的标准规范
简介：DESIG: G188 05 ^TITLE: Standard Specification for Leak Detector Solutions Intended for Use on Brasses and Other Copper Alloys ^SCOPE:1. Scope 1.1 This specification covers the requirements for leak detector solutions suitable for use in checking the leakage of valves, pipes, fittings, joints, and so forth of a pressurized gas system fabricated from brasses and other copper alloys.1.2 This specification deals with the stress corrosion cracking aspect of leak detector solutions. The effectiveness, chemical, physical and mechanical properties of leak detector solutions are not within the scope of this specification.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.
信息：ICS：77.120.30 CCS：H62 发布：2005 实施：

ASTM F78-97 用二次标准校准氦检漏仪的标准试验方法
简介：
信息：ICS： CCS：发布：1991-01-01 实施：

ASTM E1603/E1603M-11(2017) 使用质谱检漏仪或残留气体分析仪进行泄漏测量的标准实践
简介：
信息：ICS：23.040.99 CCS：发布：2017-06-01 实施：

ASTM G188-2005 黄铜和其他铜合金用检漏仪溶液的标准规范
简介：DESIG: G188 05 ^TITLE: Standard Specification for Leak Detector Solutions Intended for Use on Brasses and Other Copper Alloys ^SCOPE:1. Scope 1.1 This specification covers the requirements for leak detector solutions suitable for use in checking the leakage of valves, pipes, fittings, joints, and so forth of a pressurized gas system fabricated from brasses and other copper alloys.1.2 This specification deals with the stress corrosion cracking aspect of leak detector solutions. The effectiveness, chemical, physical and mechanical properties of leak detector solutions are not within the scope of this specification.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.
信息：ICS：77.120.30 (Copper and copper alloys) CCS：J04 发布：2005 实施：

ISO 3530:1979 真空技术——质谱仪型检漏仪校准
简介：
信息：ICS：23.160 CCS：发布：1979-09-01 实施：

JB/T 20180-2017 隔离装置用手套检漏仪
简介：
信息：ICS：11.120.30 CCS：C95 发布：2017-01-09 实施：2017-07-01

DL/T 846.6-2004 高电压测试设备通用技术条件.第6部分: 六氟化硫气体检漏仪
简介：
信息：ICS：27.100 CCS：F24 发布：2004-03-09 实施：2004-06-01

ISO 3530-1979 真空技术质谱仪型检漏仪校准
简介：Only leak detectors are described which have an integral high vacuum system to maintain the sensing element of the mass spectrometer at a low pressure. Two procedures are outlined, one to determine the minimum detectable leak rate and the other for determination of the minimum detectable concentration ratio.
信息：ICS：23.160 CCS：J78 发布：1979-09 实施：

KS A 0083-2013 质谱计式检漏仪校准
简介：이 표준은 질량 분석계를 검지기로 사용하고, 그 분석관을 작동 가능한 진공 상태로 유지하기 위한진공 배기계를 내장하는 질량 분석계형 누출 탐지기(이하 누출 탐지기라 한다.)의 교정 방식에 대하여 규정한다.다만, 이 방법은 주로 헬륨 4를 사용하는 것에 대하여 적용한다.또한 다른 가스를 사용하는 것에도 준용한다.
信息：ICS：01.040.17;23.160 CCS：A50 发布：2013-11-05 实施：2013-11-05

KS B ISO 3530-2002 真空技术.质谱仪型检漏仪校准
简介：이 규격은 질량 분광계형 누설 탐지기의 교정에 사용되는 절차를 규정한다. 이 규격
信息：ICS：23.16 CCS：J78 发布：2002-12-31 实施：2002-12-31

AIR FORCE MIL-V-26115 A-1957 AF-E34T-1型真空系统辅助检漏仪
简介：This specification Covors the requirements for one type of auxiliary leak detector vacuum system, designated AP/E34T-1.
信息：ICS： CCS：Q82 发布：1957-07-12 实施：