涂层重量检测标准涂层重量-中析研究所检测

(CMA)

(CNAS)

(ISO)

(高新技术企业)

涂层重量相关标准参考信息

GB/T 34190-2017 电工钢表面涂层的重量（厚度） X射线光谱测试方法
简介：
信息：ICS：77.040.99 CCS：H21 发布：2017-09-07 00:00:00.0 实施：2018-06-01 00:00:00.0

ASTM A90/A90M-2013 锌或锌合金涂层钢铁制品涂层重量[质量]的标准试验方法
简介：3.1x00a0;This test method provides a standard method for determining the weight [mass] of coating for comparison with specification requirements. A coating of zinc on iron or steel articles provides protection against corrosion. As the protection is provided by sacrificial loss of zinc, the degree of protection is proportional to the weight [mass] of zinc coating. Specifications for zinc-coated articles frequently provide for different classes of coating so that the purchaser can select the coating weight [mass] most suitable to his needs. 1.1x00a0;This test method covers procedures for determining the weight [mass] of coating on iron or steel sheet, wire, and other articles in which the coating is zinc or a zinc alloy, such as zinc-58201;% aluminum (including zinc-58201;% aluminum-mischmetal and zinc-58201;% aluminum-0.18201;% magnesium), zinc-aluminum-magnesium (including zinc-5 to 98201;% aluminum-magnesium and zinc-9 to 138201;% aluminum-magnesium) or 558201;% aluminum-zinc. In the body of this test method, reference to zinc coating shall be interpreted to also include zinc alloy coating except where specifically stated otherwise. 1.2x00a0;The final results determined by this test method shall be expressed in inch-pound units or SI units, depending on the units used in the material specification to which the results are to be compared. Certain portions of the procedure involving determination of specimen weight [mass] have traditionally been performed in SI units, and corresponding inch-pound units are not included. 1.3x00a0;For sheet products, the final results are expressed as either coating weight [mass] total both sides, or coating weight [mass] separately on each side, depending on the specified requirements. 1.4x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazards statements see 5.1.
信息：ICS：25.220.40 (Metallic coatings) CCS：A29;H62 发布：2013 实施：

ASTM A90/A90M-07 用锌或锌合金涂层的钢铁制品涂层重量[质量]的标准试验方法
简介：
信息：ICS：25.220.40 CCS：发布：2007-05-01 实施：

ASTM D7232-06(2022) 用重量损失法快速测定涂层非挥发性含量的标准试验方法
简介：
信息：ICS：87.040 CCS：发布：2022-12-01 实施：

KS D ISO 10111-2012(2022) 金属和其他无机涂层单位面积质量的测量重量分析和化学分析方法综述
简介：
信息：ICS： CCS：发布：2012-11-10 实施：

ASTM A309-01(2007) 用三点试验法测定薄钢板涂层重量和成分的标准试验方法
简介：
信息：ICS：77.140.50 CCS：发布：2007-05-01 实施：

KS D ISO 17925-2021 钢上的锌和/或铝基涂层.单位面积涂层质量和化学成分的测定.重量分析法电感耦合等离子体原子发射光谱法和火焰原子吸收光谱法
简介：
信息：ICS： CCS：发布：2021-10-27 实施：

KS D ISO 10111-2012(2017) 金属和其他无机涂层 - 大众的每单位面积的测量 - 的重量和化学分析方法评述
简介：
信息：ICS： CCS：发布：2012-11-10 实施：

ASTM F2217-02(2007) 涂层/粘合剂重量测定的标准实践
简介：
信息：ICS：25.220.20 CCS：发布：2007-04-01 实施：

ASTM B767-88(2021) 用重量分析和其他化学分析程序测定电沉积和相关涂层单位面积质量的标准指南
简介：
信息：ICS：25.220.40 CCS：发布：2021-10-01 实施：

ASTM F2217-02(2012) 涂层/粘合剂重量测定的标准实践
简介：
信息：ICS：25.220.20 CCS：发布：2012-11-01 实施：

TCVN 7665-2007 金属涂层.黑色金属材料上的热浸镀锌层.用重量测定法测定单位面积重量
简介：
信息：ICS： CCS：发布：2007 实施：

ASTM A754/A754M-21 用X射线荧光法测定钢上金属涂层的涂层重量[质量]的标准试验方法
简介：
信息：ICS：17.040.20 CCS：发布：2021-05-01 实施：

ASTM A90/A90M-11 用锌或锌合金涂层的钢铁制品涂层重量[质量]的标准试验方法
简介：
信息：ICS：25.220.40 CCS：发布：2011-11-01 实施：

ASTM A90/A90M-06 用锌或锌合金涂层的钢铁制品涂层重量[质量]的标准试验方法
简介：
信息：ICS：25.220.40 CCS：发布：2006-11-15 实施：

ASTM A90/A90M-21 用锌或锌合金涂层的钢铁制品涂层重量[质量]的标准试验方法
简介：
信息：ICS：25.220.40 CCS：发布：2021-05-01 实施：

BS EN ISO 2106-2011 铝及铝合金阳极氧化.阳极氧化涂层每单位面积质量(表面密度)的测定.重量法
简介：This International Standard specifies a gravimetric method for determining the mass per unit area (surfacedensity) of anodic oxidation coatings on aluminium and its alloys.The method is applicable to all oxidation coatings formed by anodizing aluminium and its alloys, either cast orwrought, and is suitable for most aluminium alloys, except those in which the copper content is greater than6 %.NOTE 1 A high content of copper in the alloy can lead to increased dissolution of the basis aluminium.NOTE 2 If the thickness is known with sufficient precision (for example, using the method specified in ISO 2128),determination of the mass per unit area (surface density) of the coatings will enable its apparent density to be calculated.Conversely, if the conditions of application of the coating and its density are known, the determination of its mass per unitarea (surface density) can permit calculation of the average mass and an approximate evaluation of the thickness (see theNote in Clause 6).
信息：ICS：25.220.20;77.120.10 CCS：A29 发布：2011-03-31 实施：2011-03-31

ASTM A428/A428M-06 镀铝铁或钢制品上涂层重量[质量]的标准试验方法
简介：
信息：ICS：25.220.40 CCS：发布：2006-11-01 实施：

ASTM A428/A428M-21 镀铝铁或钢制品上涂层重量[质量]的标准试验方法
简介：
信息：ICS：25.220.40 CCS：发布：2021-05-01 实施：

EN ISO 2106-2011 铝及铝合金阳极氧化.阳极氧化涂层每单位面积质量(表面密度)的测定.重量法
简介：This International Standard specifies a gravimetric method for determining the mass per unit area (surface density) of anodic oxidation coatings on aluminium and its alloys
信息：ICS：25.220.20 CCS：发布：2011-03-01 实施：

KS D ISO 17925-2006 钢上锌和/或铝基涂层.单位面积涂层质量和化学组分的测定.重量分析法、感应耦合等离子体原子辐射光谱测定法和火焰原子吸收光谱测定法
简介：이 규격은 무게 측정으로 단위 면적당 도금 질량을 측정하고, 유도 결합 플라스마 원자 방출
信息：ICS：25.220.40;77.080.20 CCS：A29 发布：2006-01-18 实施：2006-01-18

ASTM A90/A90M-2021 钢铁制品上锌或锌合金涂层重量[质量]的标准试验方法
简介：1.1?This test method covers procedures for determining the weight [mass] of coating on iron or steel sheet, wire, and other articles in which the coating is zinc or a zinc alloy, such as zinc-5 % aluminum (including zinc-5 % aluminum-mischmetal and zinc-5 % aluminum-0.1 % magnes
信息：ICS： CCS：发布：2021 实施：

ISO 2106:2011 铝及其合金的阳极氧化——阳极氧化涂层单位面积质量（表面密度）的测定——重量法
简介：
信息：ICS：25.220.20 CCS：发布：2011-02-23 实施：

KS D ISO 17925-2006(2016) 钢上锌和/或铝基涂层单位面积涂层质量和化学成分的测定重量法、电感耦合等离子体原子发射光谱法和火焰原子吸收光谱法
简介：
信息：ICS： CCS：发布：2006-01-18 实施：

ASTM A754/A754M-2021 用X射线荧光测定钢上金属涂层涂层重量(质量)的标准试验方法
简介：1.1?This test method covers the use of X-ray fluorescence (XRF) for determining the coating weight [mass] of metallic coatings on steel sheet. The test method is intended to be used for “on-line” measurements of coating on continuous production lines and includes procedures for
信息：ICS： CCS：发布：2021 实施：

SAE AS 22759/180-2011 150℃、600V电线、聚四氟乙烯/聚酰亚胺绝缘的轻重量的锡涂层、铜导线
简介：This specification has been developed at the request of Naval Air Systems Command and the United States Air Force. This product is based on AS22759/80 with additional requirements including a smooth outer fluoropolymer surface.
信息：ICS：49.060 CCS：发布：2011-02-15 实施：

DIN EN ISO 1460-2020 金属涂层. 黑色金属材料上的热浸镀锌涂层. 单位面积质量的重量测定(ISO 1460-2020); 德文版 EN ISO 1460-2020
简介：This document specifies a method of determining the mass per unit area of hot dip galvanized coatings on ferrous materials.
信息：ICS：25.220.40 CCS：发布：2020-12-01 实施：

ASTM A754/A754M-2011(2016) 采用X射线荧光法测定钢金属涂层的涂层重量 (质量) 的标准试验方法
简介：1.1x00a0;This test method covers the use of X-ray fluorescence (XRF) for determining the coating weight (mass) of metallic coatings on steel sheet. The test method is intended to be used for x201c;on-linex201d; measurements of coating on continuous production lines. 1.2x00a0;This test method is applicable to the coatings covered by the following ASTM specifications: A599/A599M, A623, A623M, A653/A653M, A792/A792M, A875/A875M, A879/A879M, A918, A924/A924M, A1046/A1046M, and A1063/A1063M. It may be applicable to other coatings, providing that the elemental nature of the coating and substrate are compatible with the technical aspects of XRF such as the absorption coefficient of the system, primary radiation, fluorescent radiation, type of detection. 1.3x00a0;This test method includes the procedure for developing a single standard determination of coating weight (mass). 1.4x00a0;This test method includes procedures for both X-ray tube and isotope coating weight (mass) measuring instruments. 1.5x00a0;The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. 1.6x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：17.040.20 CCS：发布：2011 实施：

ASTM A90/A90M-2006 带有锌或锌合金涂层的钢铁上的涂层重量[质量]的标准试验方法
简介：1.1 This test method covers procedures for determining the weight [mass] of coating on iron or steel sheet, wire, and other articles in which the coating is zinc or a zinc alloy, such as zinc-5 % aluminum (including zinc-5 % aluminum-mischmetal and zinc-5 % aluminum-0.1 % magnesium) or 55 % aluminum-zinc. In the body of this test method, reference to zinc coating shall be interpreted to also include zinc alloy coating except where specifically stated otherwise. 1.2 The final results determined by this test method shall be expressed in inch-pound units or SI units, depending on the units used in the material specification to which the results are to be compared. Certain portions of the procedure involving determination of specimen weight [mass] have traditionally been performed in SI units, and corresponding inch-pound units are not included. 1.3 For sheet products, the final results are expressed as either coating weight [mass] total both sides, or coating weight [mass] separately on each side, depending on the specified requirements.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazards statements see 5.1.
信息：ICS：25.220.40 (Metallic coatings) CCS：发布：2006 实施：

ISO 1460:2020 金属涂层 - 黑色金属材料上的热浸镀锌涂层 - 重量确定单位面积质量
简介：
信息：ICS：25.220.40 CCS：发布：2020-09-14 实施：

ASTM A90/A90M-2011 锌或锌合金涂层钢铁制品涂层重量[质量]的标准试验方法
简介：This test method provides a standard method for determining the weight [mass] of coating for comparison with specification requirements. A coating of zinc on iron or steel articles provides protection against corrosion. As the protection is provided by sacrificial loss of zinc, the degree of protection is proportional to the weight [mass] of zinc coating. Specifications for zinc-coated articles frequently provide for different classes of coating so that the purchaser can select the coating weight [mass] most suitable to his needs. 1.1 This test method covers procedures for determining the weight [mass] of coating on iron or steel sheet, wire, and other articles in which the coating is zinc or a zinc alloy, such as zinc-5 % aluminum (including zinc-5 % aluminum-mischmetal and zinc-5 % aluminum-0.1 % magnesium), zinc-aluminum-magnesium (including zinc-5 to 9 % aluminum-magnesium and zinc-9 to 13 % aluminum-magnesium) or 55 % aluminum-zinc. In the body of this test method, reference to zinc coating shall be interpreted to also include zinc alloy coating except where specifically stated otherwise. 1.2 The final results determined by this test method shall be expressed in inch-pound units or SI units, depending on the units used in the material specification to which the results are to be compared. Certain portions of the procedure involving determination of specimen weight [mass] have traditionally been performed in SI units, and corresponding inch-pound units are not included. 1.3 For sheet products, the final results are expressed as either coating weight [mass] total both sides, or coating weight [mass] separately on each side, depending on the specified requirements. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazards statements see 5.1.
信息：ICS：25.220.40 (Metallic coatings) CCS：A29 发布：2011 实施：

ASTM D3708-88(2005) 窗帘涂层操作中蜡重量的标准试验方法
简介：
信息：ICS：85.060 CCS：发布：2005-05-01 实施：

ISO 2106:2019 铝及其合金的阳极氧化 - 阳极氧化涂层单位面积质量（表面密度）的测定 - 重量法
简介：
信息：ICS：25.220.20 CCS：发布：2019-11-29 实施：

ASTM A754/A754M-2011 钢表面金属涂层重量(质量)X射线荧光测量的标准试验方法
简介：1.1 This test method covers the use of X-ray fluorescence (XRF) for determining the coating weight (mass) of metallic coatings on steel sheet. The test method is intended to be used for x201C;on-linex201D; measurements of coating on continuous production lines. 1.2 This test method is applicable to the coatings covered by the following ASTM specifications: A599/A599M, A623, A623M, A653/A653M, A792/A792M, A875/A875M, A879/A879M, A918, A924/A924M, A1046/A1046M, and A1063/A1063M. It may be applicable to other coatings, providing that the elemental nature of the coating and substrate are compatible with the technical aspects of XRF such as the absorption coefficient of the system, primary radiation, fluorescent radiation, type of detection. 1.3 This test method includes the procedure for developing a single standard determination of coating weight (mass). 1.4 This test method includes procedures for both X-ray tube and isotope coating weight (mass) measuring instruments. 1.5 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：17.040.20 (Properties of surfaces) CCS：A29 发布：2011 实施：

ASTM E1659-2005 电镀镍锌合金薄钢板的涂层重量和化学分析的标准试验方法
简介：These test methods for the chemical analysis of zinc-nickel alloy coating on sheet steel are primarily intended as referee methods to test such materials for compliance with compositional specifications such as found in Specification A 918, particularly those under the jurisdiction of ASTM Committee A05 on Metallic-Coated Iron and Steel Products. It is assumed that all who use these test methods will be trained analysts capable of performing common laboratory procedures skillfully and safely. It is expected that work will be performed in a properly equipped laboratory under appropriate quality control practices such as those described in Guide E 882. These test methods must be applied twice, once to each side of the specimen if coating weight and composition are required for both sides of a coated sheet. Two separate specimens are required for this purpose.1.1 These test methods cover independently the chemical analysis of each surface of zinc-nickel alloy electrolytically coated on steel sheet. The coatings have chemical compositions within the following limits:AnalyteConcentration RangeCoating Weight0.0 to 80 g/m2Nickel7.0 to 17.0 %1.2 These test methods are in the following sections:SectionsCoating Weight, by the Weigh-Strip-Weigh Method (20.0 to 45.0 g/m2)Nickel by the Atomic Absorption Method (11.0 to 13.5 % of Coating Weight Ranging from 20 to 45 g/m2)1.3 The values stated in SI units are to be regarded as standard. In some cases, exceptions allowed in Practice E 380 are also used.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.4 This test method provides a procedure for determining independently the weight of coating on each surface of zinc-nickel alloy-coated sheet steel, in coating masses from 20 to 45 g/m2 (Note 0).Note 0The upper limit of the scope has been set at 45 g/m2 because test materials with higher coating weight were not available for testing in accordance with Practice E 173. However, recognizing the simplicity of the weigh-strip-weigh technique, materials with higher coating weights can be tested following this procedure. Users of this test method are cautioned that use of it for coating weight determinations above 45 g/m 2 is not supported by interlaboratory testing.1.5 This test method covers the determination of nickel in concentrations from 11.0 to 13.5 % in zinc-nickel coatings (). Note 2The upper limit of the scope has been set at 13.5 % because sufficient test materials containing higher nickel were unavailable in accordance with Practice E 173. However, recognizing the calibration technique of atomic absorption spectrophotometer, materials with higher nickel content may be tested following this procedure. Users of this test method are cautioned that use of it for nickel determination out of the scope is not supported by the interlaboratory testing.
信息：ICS：25.220.40 (Metallic coatings) CCS：A29 发布：2005 实施：

ASTM A428/A428M-10(2019) 镀铝铁或钢制品上涂层重量[质量]的标准试验方法
简介：
信息：ICS：25.220.40 CCS：发布：2019-05-01 实施：

ASTM A428/A428M-10 镀铝铁或钢制品上涂层重量[质量]的标准试验方法
简介：
信息：ICS：25.220.40 CCS：发布：2010-05-01 实施：

ISO 17925-2004 钢上锌和/或铝基涂层.单位面积涂层质量和化学组分的测定.重量分析法、感应耦合等离子体原子辐射光谱测定法和火焰原子吸收光谱测定法
简介：This International Standard specifies methods of determining the coating mass per unit area by gravimetry and chemical composition on one side-surface of zinc- and/or aluminium-based coatings on steel by means of inductively coupled plasma atomic emission spectrometric or flame atomic absorption spectrometry. For example, this test method applies for zinc and/or aluminium based coatings on steel such as galvanize (hot dip and electrolytic), galvaneal (hot-dip), zinc-nickel electrolytic, zinc-5 % aluminium coating (hot-dip) and zinc-55 % aluminium coating (hot-dip). Galvanizing gives a pure zinc coating. Galvanealling gives a zinc-iron alloyed coating. Zinc-nickel electrolytic methods give zinc-nickel alloyed coatings.This method is applicable to zinc contents between 40 % (mass fraction) and 100 % (mass fraction); aluminium contents between 0,02 % (mass fraction) and 60 % (mass fraction); nickel contents between 7 % (mass fraction) and 20 % (mass fraction); iron contents between 0,2 % (mass fraction) and 20 % (mass fraction); silicon contents between 0,2 % (mass fraction) and 10 % (mass fraction); lead contents between 0,005 % (mass fraction) and 2 % (mass fraction). For example, the applicable elements for these products are as follows: galvanizing is specified for iron and aluminium; galvanealling is specified for zinc, iron and aluminium; zinc-nickel electrolytic methods are specified for zinc, iron and nickel; zinc-5 % aluminium coating is specified for zinc, iron, aluminium and silicon; zinc-55 % aluminium is specified for zinc, iron, aluminium and silicon.FAAS determination for the chemical composition of a coating layer is not applicable for zinc.These test methods are intended as referee methods to test such materials for compliance with mass per unit area and compositional specifications of International Standards.
信息：ICS：25.220.40;77.080.20 CCS：A29 发布：2004-11 实施：

ASTM F2217/F2217M-13(2018) 涂层/粘合剂重量测定的标准实践
简介：
信息：ICS：25.220.20 CCS：发布：2018-09-01 实施：

ISO 6179:2010 硫化橡胶或热塑性橡胶——橡胶板和橡胶涂层织物——挥发性液体透过率的测定（重量分析法）
简介：
信息：ICS：83.140.10 CCS：发布：2010-03-01 实施：

ISO 17925:2004 钢上的锌和/或铝基涂层——单位面积涂层质量和化学成分的测定——重量法、电感耦合等离子体原子发射光谱法和火焰原子吸收光谱法
简介：
信息：ICS：25.220.40 CCS：发布：2004-10-29 实施：

ASTM A90/A90M-13(2018) 用锌或锌合金涂层的钢铁制品涂层重量[质量]的标准试验方法
简介：
信息：ICS：25.220.40 CCS：发布：2018-05-01 实施：

SAE AS 22759/180-2010 150℃、600V电线、四氟乙烯/聚酰亚胺绝缘的轻重量的锡涂层、铜导线
简介：This specification has been developed at the request of Naval Air Systems Command and the United States Air Force. This product is based on AS22759/80 with additional requirements including a smooth outer fluoropolymer surface.
信息：ICS：49.060 CCS：V40 发布：2010-02-15 实施：

ASTM A630-2003 电镀锡薄板锡涂层重量测定的标准试验方法
简介：This test method covers determination of the total tin in the sample tested and does not apportion the tin to one or the other side of the test specimen. The calculations appearing in Section 27 assume uniform distribution of tin over the two surfaces. This test method does not differentiate between free tin on the tinplate surface, tin combined with iron in the intermediate alloy layer, or tin alloyed with the steel as a residual tramp element. 1.1 These test methods include four methods for the determination of tin coating weights for electrolytic tin plate as follows:Test MethodSectionsA-Bendix Test Method3 to 9B-Constant-Current, Electrolytic Test Method (Referee Method)10 to 18C-Sellar's Test Method19 to 28D-Titration Test Method29 to 371.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：25.220.40 (Metallic coatings) CCS：A29 发布：2003 实施：

ASTM A754/A754M-2018 用X射线荧光测定钢上金属涂层涂层重量(质量)的标准试验方法
简介：1.1x00a0;This test method covers the use of X-ray fluorescence (XRF) for determining the coating weight (mass) of metallic coatings on steel sheet. The test method is intended to be used for x201c;on-linex201d; measurements of coating on continuous production lines. 1.2x00a0;This test method is applicable to the coatings covered by the following ASTM specifications: A463/A463M, A599/A599M, A623, A623M, A653/A653M, A792/A792M, A875/A875M, A879/A879M, A918, A924/A924M, A1046/A1046M, A1063/A1063M, and A1079. It may be applicable to other coatings, providing that the elemental nature of the coating and substrate are compatible with the technical aspects of XRF such as the absorption coefficient of the system, primary radiation, fluorescent radiation, type of detection. 1.3x00a0;This test method includes the procedure for developing a single standard determination of coating weight (mass). 1.4x00a0;This test method includes procedures for both X-ray tube and isotope coating weight (mass) measuring instruments. 1.5x00a0;The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. 1.6x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7x00a0;This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
信息：ICS：17.040.20 CCS：A29 发布：2018 实施：

ASTM A428/A428M-2010 铝涂层钢铁产品上的镀层重量的标准试验方法
简介：This test method provides a standard method of determining the weight [mass] of coating for comparison with specification requirements. A coating of aluminum on iron or steel articles provides protection against corrosion by forming a relatively inert barrier. Specifications for aluminum-coated articles occasionally provide for different classes (weights) [masses] of coating so that the purchaser can select the coating weight [mass] most suited to his needs. The heavier coating will provide greater protection against mechanical damage which may break the coating. 1.1 This test method covers procedures for determining the weight [mass] of coating on aluminum-coated iron or steel sheets and wire, and on other aluminum-coated iron and steel articles. 1.2 The final results determined by this test method shall be expressed in inch-pound units or SI units, depending on the units used in the material specification to which the results are to be compared. Certain portions of the procedure involving determination of specimen weight [mass] have traditionally been performed in SI units, and corresponding inch-pound units are not included. 1.3 For sheet products, the final results are expressed as either coating weight [mass] total both sides, or coating weight [mass] separately on each side, depending on the specified requirements. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For a specific precautionary statement, see Note 1.
信息：ICS：25.220.40 CCS：A29 发布：2010 实施：

ASTM F2217-02 涂层/粘合剂重量测定的标准实践
简介：
信息：ICS：25.220.20 CCS：发布：2002-12-10 实施：

ISO 6179-2017 橡胶硫化或热塑性橡胶板和橡胶涂层织物 - 挥发性液体透过率的测定（重量分析技术）
简介：
信息：ICS：83.140.10 CCS：发布：2017-07-31 实施：

ASTM A90/A90M-09 用锌或锌合金涂层的钢铁制品涂层重量[质量]的标准试验方法
简介：
信息：ICS：25.220.40 CCS：发布：2009-05-01 实施：

KS D ISO 3892-2002 金属材料上的转化涂层.单位面积涂层质量的测定.重量分析法
简介：이 규격은 금속 소지 위의 화성 처리 피막의 단위 면적당 질량 측정을 위한 중량법을 규정한
信息：ICS：25.220.20 CCS：A29 发布：2002-05-01 实施：2002-05-01

ASTM A428/A428M-10(2014) 镀铝铁或钢制品上涂层重量[质量]的标准试验方法
简介：
信息：ICS：25.220.40 CCS：发布：2014-08-01 实施：

BS EN 12373-7-2002 铝和铝合金.阳极化处理.通过测量浸入预先进行酸处理的磷酸/铬酸溶液中后的重量损失来评价密封阳极氧化涂层的质量
简介：This European Standard specifies a method of assessing the quality of sealed anodic oxidation coatings onaluminium and its alloys by measurement of the loss of mass after immersion in phosphoric acid/chromic acidsolution with prior acid treatment. A related standard (EN 12373-61)) describes the same method used without prioracid treatment.The method is particularly applicable to anodic oxidation coatings intended for architectural purposes. For lesssevere applications, the method described in EN 12373-61) may be more suitable.The method is not applicable to:? hard-type anodic oxidation coatings which normally are not sealed;? anodic oxidation coatings that have been sealed only in dichromate solutions;? anodic oxidation coatings produced in chromic acid solutions;? anodic oxidation coatings that have undergone a treatment to render them hydrophobic.The method is destructive and can serve as a reference method in case of doubt or dispute regarding the results ofthe test for loss of absorptive power (EN 12373-41)), or the measurement of admittance (EN 12373-51)).
信息：ICS：25.220.20;77.120.10 CCS：发布：2009-04-30 实施：2009-04-30

KS D ISO 1460-2002(2017) 钢铁材料的热浸镀锌涂层 - 每单位面积的质量的重量分析测定
简介：
信息：ICS： CCS：发布：2002-05-01 实施：

ASTM A90/A90M-13 用锌或锌合金涂层的钢铁制品涂层重量[质量]的标准试验方法
简介：
信息：ICS：25.220.40 CCS：发布：2013-04-01 实施：

ASTM A90/A90M-2009 带有锌或锌合金涂层的钢铁上的涂层重量[质量]的标准试验方法
简介：This test method provides a standard method for determining the weight [mass] of coating for comparison with specification requirements. A coating of zinc on iron or steel articles provides protection against corrosion. As the protection is provided by sacrificial loss of zinc, the degree of protection is proportional to the weight [mass] of zinc coating. Specifications for zinc-coated articles frequently provide for different classes of coating so that the purchaser can select the coating weight [mass] most suitable to his needs. 1.1 This test method covers procedures for determining the weight [mass] of coating on iron or steel sheet, wire, and other articles in which the coating is zinc or a zinc alloy, such as zinc-5 % aluminum (including zinc-5 % aluminum-mischmetal and zinc-5 % aluminum-0.1 % magnesium) or 55 % aluminum-zinc. In the body of this test method, reference to zinc coating shall be interpreted to also include zinc alloy coating except where specifically stated otherwise. 1.2 The final results determined by this test method shall be expressed in inch-pound units or SI units, depending on the units used in the material specification to which the results are to be compared. Certain portions of the procedure involving determination of specimen weight [mass] have traditionally been performed in SI units, and corresponding inch-pound units are not included. 1.3 For sheet products, the final results are expressed as either coating weight [mass] total both sides, or coating weight [mass] separately on each side, depending on the specified requirements. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazards statements see 5.1.
信息：ICS：25.220.40 (Metallic coatings) CCS：H40 发布：2009 实施：