运动黏度检测标准运动黏度检测标准-中析研究所检测

(CMA)

(CNAS)

(ISO)

(高新技术企业)

运动黏度检测标准相关信息

GB/T 30515-2014 透明和不透明液体石油产品运动黏度测定法及动力黏度计算法
简介：本标准规定了采用玻璃毛细管运动黏度计测定液体石油产品运动黏度的方法,及其动力黏度的计算方法。本标准适用于透明和不透明的液体石油产品。
信息：ICS：75.080 CCS：E30 发布：2014-02-19 实施：2014-06-01

GB/T 30514-2014 玻璃毛细管运动黏度计规格和操作说明
简介：本标准规定了玻璃毛细管运动黏度计的规格和操作说明,也规定了这些黏度计的校准方法。本标准适用于按GB/T 30515步骤应用于石油产品运动黏度测定的玻璃毛细管黏度计。本标准所规定的黏度计类型为改进型奥斯特瓦尔德(Ostwald)(奥氏)黏度计(附录A)、悬液式黏度计(附录B)和逆流黏度计(附录C)。其他可满足GB/T 30515运动黏度测定精密度要求的玻璃毛细管黏度计也可使用。
信息：ICS：75.080;17.060.00 CCS：E30 发布：2014-02-19 实施：2014-06-01

GB/T 1660-2008 增塑剂运动黏度的测定
简介：本标准A法适用于运动黏度在1厘泊～15000厘泊的液体增塑剂运动黏度的测定，当黏度大于15000厘泊时，应选用直径为5.0mm或6.0mm的品氏黏度计测定。B法适用于运动黏度在10000厘泊以下的液体增塑剂运动黏度的测定。
信息：ICS：71.100;83.040.30 CCS：G70 发布：2008-06-18 实施：2009-02-01

SH/T 0956-2017 透明和不透明液体运动黏度的测定折管式自动黏度计法
简介：
信息：ICS：ICS75.080 CCS：E30 发布：2017-12-27 实施：2018-06-01

T/CEC 127-2016 变压器油、涡轮机油运动黏度测定法胡隆黏度计法
简介：变压器油、涡轮机油运动黏度测定法胡隆黏度计法
信息：ICS：27.100 CCS：D4411 发布：2016-10-21 实施：

DB35/T 1586-2016 石油产品运动黏度全自动测定方法
简介：本标准规定了采用自动仪器测定液体石油产品运动黏度的方法。本标准适用于测定透明和不透明的液体石油产品。
信息：ICS：17.060 CCS：E 04 发布：2016-06-28 实施：2016-09-28

NB/SH/T 0912-2015 发动机台架试验油100℃运动黏度测定法
简介：本标准规定了采用芬斯克逆流毛细管黏度计测定在用油100℃运动黏度的方法。本标准适用于含有烟炱的发动机台架试验油100℃运动黏度的测定。
信息：ICS：75.100 CCS：E34 发布：2015-10-27 实施：2016-03-01

JB/T 11945-2014 自动运动黏度测定仪技术条件和测试评价方法
简介：本标准规定了自动运动黏度测定仪的术语和定义、基本原理、技术要求、试验方法、检验规则及包装与随机文件、运输和贮存。本标准适用于测定透明或不透明石油和液体石油产品（指牛顿流体）运动黏度的自动运动黏度测定仪（以下简称测定仪）。
信息：ICS：17.040.30 CCS：N10;N19 发布：2014-05-06 实施：2014-10-01

NB/SH/T 0870-2013 石油产品的动力黏度和密度的测定及运动黏度的计算斯塔宾格黏度计法
简介：本标准规定了同时测定透明和不透明液体石油产品以及原油的动力黏度(η)和密度(ρ)的方法。运动黏度(υ)可由动力黏度(η)除以相同温度下的密度(ρ)得到。本标准适用于透明和不透明液体石油产品以及原油动力黏度和密度的测定及运动黏度的计算。本标准的测试结果取决于样品的性质,适用于剪切应力和剪切速率成比例(即牛顿流体)的液体。本标准仅进行了基础油的精密度考察,温度为40℃时,样品动力黏度范围为2.05mPa · s ~ 456mPa · s;温度为100℃时,样品动力黏度范围为0.83mPa · s ~ 31.6mPa · s;温度为15℃时,样品密度范围为0.82 g/cm ~ 0.92g/cm (见15.4)。本标准也可适用于超出上述的样品种类、黏度、密度和温度条件的测定,但第15章的精密度和偏差可能不适用。
信息：ICS：75.080 CCS：E30 发布：2013-06-08 实施：2013-10-01

JJF 1274-2011 运动黏度测定器校准规范
简介：本规范适用于测量黏度范围为0.3mm/s～30000mm/s，温度范围为20℃～100℃摄氏度的运动黏度测定器的校准。
信息：ICS： CCS：N51 发布：2011-01-21 实施：2011-04-21

SN/T 2639-2010 运动黏度换算至赛波特通用黏度标准方法
简介：本标准规定了石油及石油产品在任一温度下运动黏度（mm/s），利用表和方程式换算至相应温度下赛波特通用黏度（SUS)的换算方法。运动黏度值以20℃水的运动黏度值1.0034mm/s为基准。本标准适用于赛波特通用黏度（SUS)与运动黏度国际单位制之间互换计算。本标准中运动黏度采用国际单位制mm/s，温度为℉。
信息：ICS： CCS：E30 发布：2010-05-27 实施：2010-12-01

NB/SH/T 0837-2010 矿物绝缘油低温运动黏度测定法
简介：1.1本标准规定了透明及不透明矿物绝缘油在经历至少20h的某一恒定低温冷浸时间后，测定一定体积的试样在重力的作用下通过一支经检定毛细管黏度计的时间来测定其低温运动黏度的方法。1.2本标准适用于在某一恒定温度下测定运动黏度不大于20000mm／s的牛顿及非牛顿流体，特别适用于测定低温条件下液体的运动黏度。在低温(-40℃)或温度介于浊点与倾点(典型值-20℃)之间，一些液体在充分冷却的条件下可能会出现超高黏度。
信息：ICS：75.140 CCS：E38 发布：2010-05-01 实施：2010-10-01

KS M ISO 3104-2008 石油产品.透明和不透明液体.运动粘度的测定和动力黏度的计算
简介：이 규격은 교정된 유리제 모세관식 점도계를 가지고, 중력하에서 흐르는 일정한 부피의 유체에
信息：ICS：75.080 CCS：E30 发布：2008-03-31 实施：2008-03-31

ASTM D7279-2008 用自动黏度计法测定透明与不透明液体运动粘度的标准试验方法
简介：Many petroleum products and some non-petroleum products are used as lubricants in the equipment, and the correct operation of the equipment depends upon the appropriate viscosity of the lubricant being used. Additionally, the viscosity of many petroleum fuels is important for the estimation of optimum storage, handling, and operational conditions. Thus, the accurate determination of viscosity is essential to many product specifications. The viscosity of used oils is a commonly determined parameter in the oil industry to assess the effect of engine wear on the lube oils used, as well as the degradation of the engine parts during operation. The Houillon viscometer tube method offers automated determination of kinematic viscosity. Typically a sample volume of less than 1 mL is required for the analysis.1.1 This test method covers the measurement of the kinematic viscosity of transparent and opaque liquids such as fresh and used lubricating oils using a Houillon viscometer in automated mode. 1.2 The range of kinematic viscosity capable of being measured by this test method is from 2 to 1500 mm2/s (see Fig. 1). The range is dependent on the tube constant utilized. The temperature range that the apparatus is capable of achieving is between 20x00B0;C and 150x00B0;C, inclusive; however, the precision has only been determined for the viscosity range 25 to 150 mm2/s at 40x00B0;C and 5 to 16 mm2/s at 100x00B0;C for the materials listed in the precision section. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see Section 6.
信息：ICS：17.060 (Measurement of volume, mass, density, visc CCS：N51 发布：2008 实施：

ASTM D7279-2006 用自动黏度计法测定透明与不透明液体运动粘度的标准试验方法
简介：Many petroleum products and some non-petroleum products are used as lubricants in the equipment, and the correct operation of the equipment depends upon the appropriate viscosity of the lubricant being used. Additionally, the viscosity of many petroleum fuels is important for the estimation of optimum storage, handling, and operational conditions. Thus, the accurate determination of viscosity is essential to many product specifications. The viscosity of used oils is a commonly determined parameter in the oil industry to assess the effect of engine wear on the lube oils used, as well as the degradation of the engine parts during operation. The Houillon viscometer tube method offers automated determination of kinematic viscosity. Typically a sample volume of less than 1 mL is required for the analysis.1.1 This test method covers the measurement of the kinematic viscosity of transparent and opaque liquids such as fresh and used lubricating oils using a Houillon viscometer in automated mode.1.2 The range of kinematic viscosity covered by this test method is from 0.2 to 1000 mm2/s in the temperature range between 20176;C and 150176;C; however, the precision has only been determined for the materials, viscosity range, and temperatures as stated in the precision section (viscosity range 25 to 150 mm2/s at 40176;C and 5 to 16 mm2/s at 100176;C).1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see Section 6.
信息：ICS：17.060 (Measurement of volume, mass, density, visc CCS：N51 发布：2006 实施：