划格检测标准划格检测标准-中析研究所检测

(CMA)

(CNAS)

(ISO)

(高新技术企业)

划格检测标准相关信息

GB/T 9286-2021 色漆和清漆划格试验
简介：
信息：ICS：87.040 CCS：G50 发布：2021-08-20 00:00:00.0 实施：2022-03-01 00:00:00.0

GB/T 31586.2-2015 防护涂料体系对钢结构的防腐蚀保护涂层附着力/内聚力(破坏强度)的评定和验收准则第2部分:划格试验和划叉试验
简介：GB/T 31586的本部分规定了以直角网格图形（划格）或以×形（划叉）切割涂层并穿透至基材来评定涂层体系抗性等级的试验方法。本部分仅在规定了划格方法或划叉方法以及合适的等级表中等级的情况下才适用。本部分也规定了适用的设备、定义了检查区域、抽样方案和接受/拒绝准则。本部分没有规定特定涂层体系的等级。
信息：ICS：87.040 CCS：G50 发布：2015-07-03 实施：2016-02-01

GB/T 9286-1998 色漆和清漆漆膜的划格试验
简介： 本标准规定了在以直角网格图形切割涂层穿透至底材时来评定涂层从底材上脱离的抗性的一种试验方法。用这种经验性的试验程序测得的性能，除了取决于该涂料对上道涂层或底材的附着力外，还取决于其他各种因素。所以不能将这个试验程序看作是测定附着力的一种方法。注1：虽然本试验主要规定用于实验室，但也适用于现场试验。所规定的方法可用作通过/不通过，或在适宜的场合，可用作一种六级分级试验。当用于多层涂层体系时，可用来评定该涂层体系中各道涂层从每道其他涂层脱离的抗性。本试验可在涂有罩面漆的物体上和/或特制试样上进行。虽然本试验方法适用于硬质底材（钢）和软质底材（木材和塑料）上的涂料，但这些不同底材需要采用一种不同的试验步骤。本试验方法不适用于涂膜厚度大于250μm的涂层，也不适用于有纹理的涂层。注2：当应用于设计成凹凸不平的图案表面的涂层时，该方法所得的结果会有较大的偏差。
信息：ICS：87.040 CCS：G50 发布：1998-11-04 实施：1999-06-01

DIN EN ISO 2409-2013 涂料和清漆.划格试验(ISO 2409-2013).德文版本EN ISO 2409-2013
简介：
信息：ICS：87.040 CCS：G51 发布：2013-06 实施：

BS EN ISO 2409-2013 涂料和清漆.划格试验
简介：
信息：ICS：87.040 CCS：G51 发布：2013-02-28 实施：2013-02-28

ISO 2409-2013 涂料和清漆.划格试验
简介：
信息：ICS：87.040 CCS：G51 发布：2013-02 实施：

GOST R 54563-2011 涂装材料.胶黏剂的划格测定方法
简介：
信息：ICS：87.040 CCS：发布：2011 实施：2013-01-01

SANS 2409-2008 油漆及清漆.划格试验
简介：Describes a test method for assessing the resistance of paint coatings to separation from substrates when a right-angle lattice pattern is cut into the coating, penetrating through to the substrate. The property measured by this empirical test procedure
信息：ICS：87.040 CCS：G51 发布：2008-05-09 实施：

DIN EN ISO 2409-2007 涂料和清漆.划格试验(ISO 2409-2007)
简介：This International Standard describes a test method for assessing the resistance of paint coatings toseparation from substrates when a right-angle lattice pattern is cut into the coating, penetrating through to thesubstrate. The property measured by this empirical test procedure depends, among other factors, on theadhesion of the coating to either the preceding coat or the substrate. This procedure is not to be regarded,however, as a means of measuring adhesion.Where a measurement of adhesion is required, attention is drawn to the method described in ISO 4624.NOTE 1 Although the test is primarily intended for use in the laboratory, the test is also suitable for field testing.The method described may be used either as a pass/fail test or, where circumstances are appropriate, as asix-step classification test. When applied to a multi-coat system, assessment of the resistance to separation ofindividual layers of the coating from each other may be made.The test can be carried out on finished objects and/or on specially prepared test specimens.Although the method is applicable to paint on hard (e.g. metal) and soft (e.g. wood and plaster) substrates,these different substrates need a different test procedure (see Clause 6).The method is not suitable for coatings of total thickness greater than 250 pm or for textured coatings.NOTE 2 The method, when applied to coatings designed to give a rough patterned surface, will give results which willshow too much variation (see also ISO 16276-2).
信息：ICS：87.040 CCS：G51 发布：2007-08 实施：

BS EN ISO 16276-2-2007 防护涂料系统对钢结构的腐蚀防护.涂层粘附/粘聚(断裂强度)的评定和验收标准.划格测试和X切割测试
简介：ISO 16276-2:2007 specifies procedures for rating the resistance of coating systems when a cut in the form of a right-angle lattice pattern (cross-cut) or in the form of an X (X-cut) is made into the coating, penetrating through to the substrate.It also specifies suitable equipment and defines inspection areas, sampling plans and acceptance/rejection criteria.It does not specify ratings for particular coating systems.
信息：ICS：87.040 CCS：G51;A29 发布：2007-06-29 实施：2007-06-29

EN ISO 16276-2-2007 防护涂料系统对钢结构的腐蚀防护.涂层粘附粘聚(断裂应力) 的评定和验收标准.第2部分:划格测试和X切割测试
简介：
信息：ICS：87.040 CCS：发布：2007-05-01 实施：

ISO 2409-2007 涂料和清漆.划格试验
简介：This International Standard describes a test method for assessing the resistance of paint coatings toseparation from substrates when a right-angle lattice pattern is cut into the coating, penetrating through to thesubstrate. The property measured by this empirical test procedure depends, among other factors, on theadhesion of the coating to either the preceding coat or the substrate. This procedure is not to be regarded,however, as a means of measuring adhesion.Where a measurement of adhesion is required, attention is drawn to the method described in ISO 4624.NOTE 1 Although the test is primarily intended for use in the laboratory, the test is also suitable for field testing.The method described may be used either as a pass/fail test or, where circumstances are appropriate, as asix-step classification test. When applied to a multi-coat system, assessment of the resistance to separation ofindividual layers of the coating from each other may be made.The test can be carried out on finished objects and/or on specially prepared test specimens.Although the method is applicable to paint on hard (e.g. metal) and soft (e.g. wood and plaster) substrates,these different substrates need a different test procedure (see Clause 6).The method is not suitable for coatings of total thickness greater than 250 μm or for textured coatings.NOTE 2 The method, when applied to coatings designed to give a rough patterned surface, will give results which willshow too much variation (see also ISO 16276-2).
信息：ICS：87.040 CCS：G51 发布：2007-05 实施：

ISO 16276-2-2007 防护涂料系统对钢结构的腐蚀防护.涂层粘附/粘聚(断裂应力)的评定和验收标准.第2部分:划格测试和X切割测试
简介：This part of ISO 16276 specifies procedures for rating the resistance of coating systems when a cut in theform of a right-angle lattice pattern (cross-cut) or in the form of an X (X-cut) is made into the coating,penetrating through to the substrate.This part of ISO 16276 is only applicable if the cross-cut or X-cut test method is specified, together with therating from the appropriate rating scale.This part of ISO 16276 also specifies suitable equipment and defines inspection areas, sampling plans andacceptance/rejection criteria.It does not specify ratings for particular coating systems.
信息：ICS：87.020;87.040;91.080.10 CCS：A29 发布：2007-05 实施：

ISO 2409-1992 色漆和清漆划格试验
简介：Specifies a test method for assessing the resistance of paint coatings to separation from substrates when a right-angle lattice pattern is cut into the coating, penetrating through to the substrate. The method may be carried out as a "pass/fail" test or as a six-step classification test. Hard and soft substrates need a different test procedure. The property meassured depends, among other factors, on the adhesion of the coating to either the preceding coat or the substrate.
信息：ICS：87.040 CCS：G51 发布：1992-08 实施：

NEN 5337-1984 色漆和清漆．划格试验
简介：De norm is van toepassing op verflagen en verflaagsystemen aangebracht op een harde stijve ondergrond.
信息：ICS： CCS：发布：1984-4-1 实施：