合金钢螺钉检测标准合金钢螺钉-中析研究所检测

(CMA)

(CNAS)

(ISO)

(高新技术企业)

合金钢螺钉相关标准参考信息

GB/T 41157.1-2022 核电厂用紧固件第1部分：合金钢螺栓、螺钉和螺柱
简介：
信息：ICS：21.060.10 CCS：J13 发布：2022-03-09 00:00:00.0 实施：2022-10-01 00:00:00.0

JIS B1051-2014 碳钢和合金钢制成的紧固件的机械特性. 指定属性种类的螺栓, 螺钉和螺柱. 粗牙和细牙螺纹
简介：This Standard specifies mechanical and physical properties of bolts,screws and studs made of carbon steel and alloy steel when tested at an ambient temperature range of 10℃ to 35℃. Fasteners (the term used when bolts,screws and studs are considered all together) that conform to the requirements of this Standard are evaluated at that ambient temperature range. They might not retain the specified mechanical and physical properties at elevated temperatures (see Annex B) and/or lower temperatures.
信息：ICS：21.060.10 CCS：J13 发布：2014-09-22 实施：

ASTM A574M-2011 合金钢内六角螺钉的标准规格［米制］
简介：1.1 This specification covers the requirements for quenched and tempered alloy steel hexagon socket-head cap screws, 1.6 mm through 48 mm in diameter having a minimum ultimate tensile strength of 1220 MPa. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. Note 18212;This specification is the metric companion of Specification A574. 1.3 The following hazard caveat pertains only to the test method portions, sections 5.1, 5.6, 8, and 12, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：21.060.10 CCS：J13 发布：2011 实施：

ASTM A574-21 合金钢内六角螺钉标准规范
简介：
信息：ICS：21.060.10 CCS：发布：2021-12-01 实施：

ASTM A574-2011 合金钢内六角螺钉的标准规格
简介：1.1 This specification covers the requirements for quenched and tempered alloy steel hexagon socket-head cap screws, 0.060 through 4 in. in diameter where high strength is required. 1.2 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard. Note 18212;A complete metric companion to Specification A574 has been developedA574M; therefore no metric equivalents are presented in this specification. 1.3 The following hazard caveat pertains only to the test method portions, sections 5.1, 5.6, 8, and 12, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：21.060.10 (Bolts, screws, studs) CCS：J13 发布：2011 实施：

ASTM F835-20 合金钢内六角头螺钉和平头沉头螺钉的标准规范
简介：
信息：ICS：21.060.10 CCS：发布：2020-08-01 实施：

JIS B1053-2014 碳钢和合金钢制成的紧固件的机械特性. 指定硬度种类的定位螺钉和类似螺纹紧固件. 粗牙和细牙螺纹
简介：
信息：ICS：21.060.10 CCS：J13 发布：2014-09-22 实施：

ASTM F2329-2011 碳素钢和合金钢螺栓,螺钉,垫圈,螺母和特殊螺纹紧固件的锌层,热浸及应用要求的标准规范
简介：1.1 This specification covers the requirements for hot-dip zinc coating applied to carbon steel and alloy steel bolts, screws, washers, nuts, and special threaded fasteners applied by the hot-dip coating process. Nails and rivets are not included in this specification. 1.2 It is intended to be applicable to fasteners that are centrifuged or otherwise handled to remove excess galvanizing bath metal (free zinc). 1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：25.220.40 (Metallic coatings) CCS：J13;A29 发布：2011 实施：

ASTM F835-18 合金钢内六角头螺钉和平头沉头螺钉的标准规范
简介：
信息：ICS：21.060.10 CCS：发布：2018-12-01 实施：

ASTM F835-13 合金钢内六角头螺钉和平头沉头螺钉的标准规范
简介：
信息：ICS：21.060.10 CCS：发布：2013-11-01 实施：

DIN EN 4161-2010 航空航天系列.镀镉合金钢长螺纹粗公差标称柄偏头十字形凹槽平头螺钉.等级:1100 MPa(室温)/235℃.德文和英文版本EN 4161-2009 + AC-2010
简介：The document specifies the characteristics of screws, pan head, offset cruciform recess, coarse tolerance normal shank, long thread, in alloy steel, cadmium plated. Classification: 1100 MPa/235 ФC.
信息：ICS：49.030.20 CCS：V20 发布：2010-08-01 实施：

ASTM F912-11(2017) 合金钢套筒螺钉标准规格
简介：
信息：ICS：21.060.10 CCS：发布：2017-06-01 实施：

NF E25-100-1-2013 碳钢和合金钢紧固件的机械性能.第1部分:具备规定的性能等级的螺栓,螺钉和螺杆.粗牙螺纹和细牙螺纹
简介：
信息：ICS：21.060.10 CCS：J13 发布：2013-05-03 实施：2013-05-03

NF L24-169-2010 航空航天系列.镀镉的合金钢长螺纹粗公差标准柄偏置十字形凹槽平头螺钉.分类:1100 PMa(室温)/235℃
简介：
信息：ICS：49.030.20 CCS：V20 发布：2010-06-01 实施：2010-06-12

ASTM A574-17 合金钢插头螺栓螺钉标准规范
简介：
信息：ICS：21.060.10 CCS：发布：2017-06-01 实施：

ASTM A574-13 合金钢插头螺栓螺钉标准规范
简介：
信息：ICS：21.060.10 CCS：发布：2013-04-01 实施：

DIN EN 4163-2010 航空航天系列.镀镉合金钢长螺纹粗公差标称柄偏移十字形凹槽100°沉孔标准头螺钉.等级:1100MPa(室温)/235℃
简介：This document specifies the characteristics of srews, 100Ф countersunk normal head, offset cruciform recess, coarse tolerance normal shank, long thread, in alloy steel, cadmium plated. Classification: 1100 MPa/235 ФC.
信息：ICS：49.030.20 CCS：V20 发布：2010-04 实施：

DIN EN 4162-2017 航空航天系列.镀镉合金钢中长度螺纹粗公差标称柄偏十字形凹槽埋头100°螺钉.分类:1100MPa(室温)/235℃
简介：
信息：ICS：49.030.20 CCS：V20 发布：2017-01 实施：

EN ISO 898-1-2013 紧固件的机械性能由碳钢和合金钢.第1部分:螺栓,螺钉和螺栓与指定的属性类,粗牙螺纹和细牙螺纹
简介：This part of ISO 898 specifies mechanical and physical properties of bolts, screws and studs made of carbon steel and alloy steel when tested at an ambient temperature range of 10 °C to 35 °C. Fasteners (the term used when bolts, screws and studs are considered all together) that conform to the requirements of this part of ISO 898 are evaluated at that ambient temperature range. They might not retain the specified mechanical and physical properties at elevated temperatures (see Annex B) and/or lower temperatures.NOTE 1 Fasteners conforming to the requirements of this part of ISO 898 are used in applications ranging from −50 °C to +150 °C. Users are advised
信息：ICS：21.060.10 CCS：发布：2013-01-01 实施：

DIN EN 4073-2010 航空航天系列.镀镉合金钢中等长度螺纹粗公差标称柄六瓣凹槽平头螺钉.等级:1100 MPa(室温)/235℃.德文和英文版本EN 4073-2009
简介：This European Standard specifies the characteristics of screws, pan head, six lobe recess, coarse tolerance normal shank, medium length thread, in alloy steel, cadmium plated. Classification: 1100 MPa / 235 ФC.
信息：ICS：49.030.20 CCS：V20 发布：2010-04 实施：

ASTM F2882/F2882M-2017 最小拉伸强度170 ksi和1170 MPa(英制和公制)的热处理合金钢螺钉的标准规格
简介：1.1x00a0;This specification covers the requirements for quenched and tempered alloy steel screws 0.060 through 11/2x00a0;in. and 1.6 through 48 mm in diameter having a minimum ultimate tensile strength of 170 KSI or 1170 MPa. 1.2x00a0;The values are stated in inch-pound units for inch fasteners and SI metric units for metric fasteners. The values stated in each system may not be exact equivalents; therefore each system shall be used independently of the other. Combining values from the two systems may result in non-conformance to the standard. 1.3x00a0;The following hazard caveat pertains only to the test method portion, Section 10, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.4x00a0;This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
信息：ICS：21.060.10 CCS：J13 发布：2017 实施：

ASTM F2329-2013 碳钢和合金钢螺栓, 螺钉, 垫圈, 螺母和特殊螺纹紧固件应用的热镀锌要求的标准规范
简介：1.1x00a0;This specification covers the requirements for hot-dip zinc coating applied to carbon steel and alloy steel bolts, screws, washers, nuts, and special threaded fasteners. It also provides for minor coating repairs. Nails and rivets are not included in this specification. 1.2x00a0;It is intended to be applicable to fasteners that are centrifuged or otherwise handled to remove excess galvanizing bath metal (free zinc). 1.3x00a0;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：25.220.40 (Metallic coatings) CCS：J13 发布：2013 实施：

DIN EN 4138-2010 航空航天系列.镀镉合金钢中长螺纹粗公差标称柄偏移十字形凹槽平头螺钉.等级:1100 MPa(室温)/235℃.德文版本EN 4138-2009
简介：The document specifies the characteristics of screws, pan head, offset cruciform recess, coarse tolerance normal shank, medium length thread, in alloy steel, cadmium plated. Classification: 1100 MPa/235 ФC.
信息：ICS：49.030.20 CCS：V20 发布：2010-04 实施：

ASTM F835-16 合金钢内六角头螺钉和平头沉头螺钉的标准规范
简介：
信息：ICS：21.060.10 CCS：发布：2016-12-01 实施：

ASTM F835-2013 合金钢凹圆头螺钉和平埋头帽螺钉的标准规范
简介：1.1x00a0;This specification covers the requirements for quenched and tempered alloy steel hexagon socket button (SBHCS) 0.060 through 0.625 thread sizes and flat countersunk (SFHCS) 0.060 through 1.5 thread sizes head cap screws having material properties for high-strength requirements. 1.2x00a0;Fasteners meeting this specification are intended for shear-type applications and have tensile requirements ranging from 122 to 150 ksi. 1.3x00a0;The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard. 1.4x00a0;The hazard statement applies only to the test method section, Section 11, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：21.060.10 (Bolts, screws, studs) CCS：J13 发布：2013 实施：

DIN EN 4162-2010 航空航天系列.1100 MPa(室温下)/235°C镀镉合金钢中等长度螺纹粗糙公差标准柄的、偏置式十字槽100°埋头标准头螺钉.德文和英文版本EN 4162-2009
简介：This document specifies the characteristics of srews, 100Ф countersunk normal head, offset cruciform recess, coarse tolerance normal shank, medium lenth thread, in alloy steel, cadmium plated. Classification: 1100 MPa/235 ФC.
信息：ICS：49.030.20 CCS：V20 发布：2010-04 实施：

ASTM A574-16 合金钢插头螺栓螺钉标准规范
简介：
信息：ICS：21.060.10 CCS：发布：2016-10-01 实施：

ASTM A574-2013 合金钢内六角螺钉的标准规格
简介：1.1x00a0;This specification covers the requirements for quenched and tempered alloy steel hexagon socket-head cap screws, 0.060 through 4 in. in diameter where high strength is required. 1.2x00a0;The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.Note 1x2014;A complete metric companion to Specification A574 has been developedx2014;A574M; therefore no metric equivalents are presented in this specification. 1.3x00a0;The following hazard caveat pertains only to the test method portions, sections 5.1, 5.6, 8, and 12, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：21.060.10 (Bolts, screws, studs) CCS：J13 发布：2013 实施：

BS EN 4073-2009 航空航天系列.镀铬的合金钢中等长度螺纹、粗公差标准柄六瓣凹槽平头螺钉.等级1100MPa(室温)/235℃
简介：This European Standard specifies the characteristics of screws, pan head, six lobe recess, coarse tolerancenormal shank, medium length thread, in alloy steel, cadmium plated.Classification: 1 100 MPa 1) / 235 °C 2).
信息：ICS：49.030.20 CCS：V20 发布：2010-01-31 实施：2010-01-31

NF L24-174-2016 航空航天系列.镀铬的合金钢中等长度螺纹、粗公差标准柄六瓣凹槽平头螺钉.等级1100MPa(室温)/235℃
简介：
信息：ICS：49.030.20 CCS：V20 发布：2016-09-30 实施：2016-09-30

DIN EN ISO 898-5-2012 碳钢和合金钢制成的紧固件的机械特性. 第5部分: 指定硬度种类的定位螺钉和类似螺纹紧固件. 粗牙和细牙螺纹(ISO 898-5-2012); 德文版本EN ISO 898-5-2012
简介：
信息：ICS：21.060.10 CCS：J13 发布：2012-09 实施：

BS EN 4161-2010 航空航天系列.镀镉合金钢长螺纹粗公差标称柄偏十字形凹槽平头螺钉.等级:1100MPa(室温)/235℃
简介：
信息：ICS：49.030.20 CCS：发布：2010-01-31 实施：2010-01-31

DIN EN 4163-2016 航空航天系列.镀镉合金钢长螺纹粗公差标称柄偏十字形凹槽埋头100°螺钉.分类:1100MPa(室温)/235℃.德文和英文版本EN 4163-2016
简介：
信息：ICS：49.030.20 CCS：V20 发布：2016-09 实施：

ASTM F835-12 合金钢内六角头螺钉和平头沉头螺钉的标准规范
简介：
信息：ICS：21.060.10 CCS：发布：2012-05-01 实施：

BS EN 4161-2009 航空航天系列.镀镉合金钢长螺纹粗公差标称柄偏十字形凹槽平头螺钉.等级:1100MPa(室温)/235℃
简介：This European Standard specifies the characteristics of screws, pan head, offset cruciform recess, coarsetolerance normal shank, long thread, in alloy steel, cadmium plated.Classification: 1 100 MPa / 235 °C.
信息：ICS：49.030.20 CCS：V20 发布：2010-01-31 实施：2010-01-31

BS EN 4163-2016 航空航天系列.镀镉合金钢长螺纹粗公差标称柄偏十字形凹槽埋头100°螺钉.分类:1100MPa(室温)/235℃
简介：
信息：ICS：49.030.20 CCS：V20 发布：2016-03-31 实施：2016-03-31

ASTM A574-12 合金钢插头螺栓螺钉标准规范
简介：
信息：ICS：21.060.10 CCS：发布：2012-04-01 实施：

BS EN 4163-2009 航空航天系列.镀镉合金钢长螺纹粗公差标称柄偏十字形凹槽埋头100°螺钉.1100MPa(室温)/235℃
简介：This European Standard specifies the characteristics of screws, 100° countersunk normal head, offsetcruciform recess, coarse tolerance normal shank, long thread, in alloy steel, cadmium plated.Classification : 1 100 MPa1) / 235 °C2).
信息：ICS：49.030.20 CCS：V20 发布：2010-01-31 实施：2010-01-31

EN 4163-2016 航空航天系列-1100MPa(室温下)/235°C镀镉合金钢长度螺纹粗糙公差标准柄的-分类:偏置式十字槽100°埋头标准头螺钉
简介：This European Standard specifies the characteristics of screws, 100° countersunk normal head, offset cruciform recess, coarse tolerance normal shank, long thread, in alloy steel, cadmium plated. Classification: 1100 MPa/235 °C.
信息：ICS：49.030.20 CCS：V11 发布：2016-03 实施：

ASTM F835-2012 合金钢凹圆头螺钉和平沉头螺钉的标准规范
简介：1.1 This specification covers the requirements for quenched and tempered alloy steel hexagon socket button (SBHCS) 0.060 through 0.625 thread sizes and flat countersunk (SFHCS) 0.060 through 1.5 thread sizes head cap screws having material properties for high-strength requirements. 1.2 Fasteners meeting this specification are intended for shear-type applications and have tensile requirements ranging from 122 to 150 ksi. 1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 The hazard statement applies only to the test method section, Section 11, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：21.060.10 (Bolts, screws, studs) CCS：J13 发布：2012 实施：

BS EN 4162-2009 航空航天系列.镀镉合金钢中长度螺纹粗公差标称柄偏十字形凹槽埋头100°螺钉.1100MPa(室温)/235℃
简介：This European Standard specifies the characteristics of screws, 100° countersunk normal head, offsetcruciform recess, coarse tolerance normal shank, medium length thread, in alloy steel, cadmium plated.Classification: 1 100 MPa1) / 235 °C2).
信息：ICS：49.030.20 CCS：V20 发布：2010-01-31 实施：2010-01-31

EN 4162-2016 航空航天系列-1100MPa(室温下)/235°C镀镉合金钢中等长度螺纹粗糙公差标准柄的-分类:偏置式十字槽100°埋头标准头螺钉
简介：This European Standard specifies the characteristics of screws, 100° countersunk normal head, offset cruciform recess, coarse tolerance normal shank, medium length thread, in alloy steel, cadmium plated. Classification: 1100 MPa/235 °C.
信息：ICS：49.030.20 CCS：V11 发布：2016-03 实施：

ASTM A574-2012 合金钢内六角螺钉的标准规格
简介：1.1 This specification covers the requirements for quenched and tempered alloy steel hexagon socket-head cap screws, 0.060 through 4 in. in diameter where high strength is required. 1.2 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard. Note 18212;A complete metric companion to Specification A574 has been developedA574M; therefore no metric equivalents are presented in this specification. 1.3 The following hazard caveat pertains only to the test method portions, sections 5.1, 5.6, 8, and 12, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：21.060.10 (Bolts, screws, studs) CCS：J13 发布：2012 实施：

BS EN 4138-2009 航空航天系列.镀镉合金钢中等长度螺纹粗公差普通柄偏十字凹槽平头螺钉.分类:1100MPa(室温)/235℃
简介：This European Standard specifies the characteristics of screws, pan head, offset cruciform recess, coarsetolerance normal shank, medium length thread, in alloy steel, cadmium plated.Classification: 1 100 MPa1) / 235 °C2).
信息：ICS：49.030.20 CCS：V20 发布：2010-01-31 实施：2010-01-31

EN 4073-2016 航空航天系列-镀铬的合金钢中等长度螺纹,粗公差标准柄内六角凹槽平头螺钉-等级:1100MPa(室温)/235℃
简介：This European Standard specifies the characteristics of screws, pan head, six lobe recess, coarse tolerance shank, medium length thread, in alloy steel, cadmium plated. Classification: 1100 MPa 1) / 235 °C 2).
信息：ICS：49.030.20 CCS：V11 发布：2016-03 实施：

ASTM F912-11 合金钢套筒螺钉标准规格
简介：
信息：ICS：21.060.10 CCS：发布：2011-11-01 实施：

SAE AS 7454A-2009 规格化和回火处理带滚压螺纹的抗拉强度135000 psi的耐高温低合金钢螺栓和螺钉
简介：This procurement specification covers aircraft quality bolts and screws made from a low alloy, heat resistant steel of the type identified under the Unified Numbering System as UNS K14675. AS7454 135 000 psi ultimate tensile strength at room temperture. AS7454-1 135 000 psi ultimate tensile strength at room temperture, nickel-cadmium plated. Primarily for aerospace propulsion system applications where good strength at temperatures up to approximately 900 °F is required and the part is protected against corrosion.
信息：ICS：49.030.20 CCS：V20 发布：2009-07-14 实施：

EN 4138-2016 航空航天系列-镀镉合金钢中长螺纹粗公差标称柄偏移十字形凹槽平头螺钉-等级:1100MPa(室温)/235℃
简介：This European Standard specifies the characteristics of screws, pan head, offset cruciform recess, coarse tolerance normal shank, medium length thread, in alloy steel, cadmium plated. Classification: 1100 MPa / 235 °C.
信息：ICS：49.030.20 CCS：V11 发布：2016-03 实施：

ASTM A574-11 合金钢插头螺栓螺钉标准规范
简介：
信息：ICS：21.060.10 CCS：发布：2011-05-01 实施：

SAE AS 7455A-2009 硬化和淬火轧制螺纹低合金钢耐热螺栓和螺钉
简介：This procurement specification covers aircraft quality bolts and screws made from a low alloy, heat resistant steel of the type identified under the Unified Numbering System as UNS K14675. The following specification designations and their properities are covered: AS7455 140 000 to 195 000 psi ultimate tensile strength at room temperture; AS7455-1 140 000 to 195 000 psi ultimate tensile strength at room temperature, nickel-cadmium plated. Primarily for aerospace propulsion system applications where high strength at temperatures up to approximately 900 °F is required and the part is protected against corrosion.
信息：ICS：49.030.20 CCS：V20 发布：2009-07-10 实施：

ASTM A574-2016 合金钢套筒头螺钉的标准规格
简介：1.1x00a0;This specification covers the requirements for quenched and tempered alloy steel hexagon socket-head cap screws, 0.060 through 4 in. in diameter where high strength is required. 1.2x00a0;The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard. 1.3x00a0;The following hazard caveat pertains only to the test method portions, sections 5.1, 5.6, 8, and 12, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：21.060.10 CCS：J13 发布：2016 实施：

ASTM A574M-11 合金钢内六角螺钉的标准规范[米制]
简介：
信息：ICS：21.060.10 CCS：发布：2011-05-01 实施：

AIA/NAS NAS 1352-2009 合金钢、不锈钢以及耐热钢UNRC-3A和UNRC-2A制穿孔或非穿孔、普通或自锁定圆柱头螺钉;修改件11
简介：
信息：ICS： CCS：发布：2009-06-22 实施：

ASTM F2329/F2329M-2015 碳钢和合金钢螺栓, 螺钉, 垫圈, 螺母和特殊螺纹紧固件应用的热镀锌要求的标准规格
简介：1.1x00a0;This specification covers the requirements for hot-dip zinc coating applied to carbon steel and alloy steel bolts, screws, washers, nuts, and special threaded fasteners. It also provides for minor coating repairs. Nails and rivets are not included in this specification. 1.2x00a0;It is intended to be applicable to fasteners that are centrifuged or otherwise handled to remove excess galvanizing bath metal (free zinc). 1.3x00a0;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：25.220.40 CCS：发布：2015 实施：

ASTM F835M-2011 合金钢底座钮扣及扁平沉头螺钉的标准规范(米制)
简介：1.1 This specification covers the requirements for quenched and tempered alloy steel hexagon socket button (SBHCS) and flat countersunk (SFHCS) head cap screws M3 through M20 thread sizes having material properties of ISO 898/1 Property Class 12.9. 1.2 Fasteners meeting this specification are intended for shear type applications and have tensile requirements equivalent to ISO 898/1 Property Class 10.9. 1.3 The hazard statement pertains only to the test method section, Section 11 of this specification. This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：21.060.10 (Bolts, screws, studs) CCS：J13 发布：2011 实施：

BS EN 4129-2009 航空航天系列.镀镉合金钢中等螺纹长度粗公差标称杆标准六角头螺钉.等级:1100 MPa(环境温度)/235℃
简介：This standard specifies the characteristics of bolts, normal hexagonal head, coarse tolerance normal shank,medium length thread, in alloy steel, cadmium plated.Classification: 1 100 MPa 1)/ 235 °C
信息：ICS：49.030.20 CCS：V20 发布：2009-05-31 实施：2009-05-31

BS EN ISO 898-1-2009 碳钢和合金钢紧固件的机械性能.具有特殊性能的螺栓,螺钉和螺柱.粗牙螺纹和细牙螺纹
简介：This part of ISO 898 specifies mechanical and physical properties of bolts, screws and studs made of carbonsteel and alloy steel when tested at an ambient temperature range of 10 °C to 35 °C. Fasteners — the termused when bolts, screws and studs are considered all together — that conform to the requirements of this partof ISO 898 are evaluated at that ambient temperature range. They might not retain the specified mechanicaland physical properties at elevated temperatures (see Annex B) and/or lower temperatures.NOTE 1 Fasteners conforming to the requirements of this part of ISO 898 are used in applications ranging from ?50 °Cto +150 °C. Users are advised to consult an experienced fastener metallurgist for temperatures outside the range of?50 °C to +150 °C and up to a maximum temperature of +300 °C when determining appropriate choices for a givenapplication.NOTE 2 Information for the selection and application of steels for use at lower and elevated temperatures is given, forexample, in EN 10269, ASTM F2281 and in ASTM A 320/A 320M.Certain fasteners might not fulfil the tensile or torsional requirements of this part of ISO 898-1 because thegeometry of their heads reduces the shear area in the head compared to the stress area in the thread. Theseinclude fasteners having a low head, with or without external driving feature, a low round or cylindrical headwith internal driving feature or a countersunk head with internal driving feature (see 8.2).This part of ISO 898 is applicable to bolts, screws and studsa) made of carbon steel or alloy steel,b) having triangular ISO metric screw thread according to ISO 68-1,c) with coarse pitch thread M1,6 to M39, and fine pitch thread M8×1 to M39×3,d) with diameter/pitch combinations according to ISO 261 and ISO 262,e) having thread tolerances according to ISO 965-1, ISO 965-2 and ISO 965-4.It is not applicable to set screws and similar threaded fasteners not under tensile stresses (see ISO 898-5).It does not specify requirements for such properties as- weldability,- corrosion resistance,- resistance to shear stress,- torque/clamp force performance, or- fatigue resistance.
信息：ICS：21.060.10 CCS：J13 发布：2009-04-30 实施：2009-04-30