钢电壶检测标准钢电壶-中析研究所检测

(CMA)

(CNAS)

(ISO)

(高新技术企业)

钢电壶相关标准参考信息

ASTM B200-22 钢和铁合金上铅和铅锡合金电沉积涂层的标准规范
简介：
信息：ICS：25.220.40 CCS：发布：2022-11-15 实施：

ASTM A1079-2013e2 通过热浸法的复相(CP)、双相(DP)和相变诱导塑性(TRIP)、镀锌(电锌)或锌铁合金涂层(镀锌扩散处理)钢片的标准规格
简介：1.1x00a0;This specification covers steel sheet, complex phase (CP) grade, dual phase (DP) grade, and transformation induced plasticity (TRIP) grade, zinc-coated (galvanized) or zinc-iron alloy-coated (galvannealed) by the hot-dip process in coils and cut lengths. 1.2x00a0;The product is produced in various zinc or zinc-iron alloy-coating masses or coating designations as shown in Table 1. 1.3x00a0;Product furnished under this specification shall conform to the applicable requirements of the latest issue of Specification A924/A924M, unless otherwise provided herein. 1.4x00a0;The product is available in a number of designations and grades with mandatory chemical requirements and mandatory mechanical properties that are achieved through thermal or thermal-mechanical treatments, and are designed to be compatible with automotive application requirements. 1.5x00a0;The grade designation nomenclature of the product differs from other hot-dip sheet products having mandatory mechanical properties in that ordering is to tensile, rather than yield strength values. 1.6x00a0;The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.7x00a0;The text of this specification references notes and footnotes that provide explanatory material. These notes and footnotes, excluding those in tables and figures, shall not be considered as requirements of this specification. 1.8x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：77.140.50 (Flat steel products and semi-products) CCS：发布：2013 实施：

IEC 60981:2004 超重型重型钢电导体
简介：
信息：ICS：29.120.10 CCS：发布：2004-05-18 实施：

ISO 24319-2022 船舶和海上技术.使用电伴热的小型钢舱口的设计和试验要求
简介：
信息：ICS：47.020.10 CCS：发布：2022-06-24 实施：

ASTM A677-12 无取向电钢全加工类型的标准规范
简介：
信息：ICS：77.140.50 CCS：发布：2012-11-01 实施：

ASTM B200-85(2004) 铅和铅锡合金在钢和铁合金上的电沉积涂层的标准规范
简介：
信息：ICS：25.220.40 CCS：发布：2004-04-01 实施：

HS/T 63-2019 《硅电钢平板轧材取向性的定性分析方法》
简介：
信息：ICS：71.040.40 CCS：G10/14 发布：2019-12-19 实施：2020-06-01

ASTM B633-11 锌和锌钢电沉积涂层标准规范
简介：
信息：ICS：25.220.40 CCS：发布：2011-10-01 实施：

ASTM B869-2004 用于CATV用户引入线的包铜钢电导线的标准规范
简介：1.1 This specification covers 21 % conductivity hard-drawn round copper-clad steel wire for coaxial cable center conductors (Note 1). Note 18212;Wire ordered to this specification is not intended for redrawing since it is furnished in the hard-drawn temper. If wire is desired for the purpose, the manufacturer should be consulted.1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
信息：ICS：29.060.10 (Wires) CCS：K11 发布：2004 实施：

IEC 60981:2019 超重型重型钢电导体
简介：
信息：ICS：29.120.10 CCS：发布：2019-08-20 实施：

IEC 60404-3-2010 电磁材料.第3部分:用单片钢板测试仪测量电钢带和钢片磁性能的方法
简介：The object of this part is to define the general principles and the technical details of themeasurement of the magnetic properties of magnetic sheets by means of a single sheettester.
信息：ICS：17.220.20; 29.030 CCS：H53 发布：2010-04 实施：

ASTM B869-2002 用于CATV用户引线的包铜钢电导线的标准规范
简介：1.1 This specification covers 21 % conductivity hard-drawn round copper-clad steel wire for coaxial cable center conductors (Note 1). Note 18212;Wire ordered to this specification is not intended for redrawing since it is furnished in the hard-drawn temper. If wire is desired for the purpose, the manufacturer should be consulted.1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
信息：ICS：29.060.10 (Wires) CCS：K12 发布：2002 实施：

IEC 60981-2019 超重型重型钢电导体
简介：
信息：ICS：29.120.10 CCS：发布：2019-08-20 实施：

ASTM B200-85(2009) 铅和铅锡合金在钢和铁合金上的电沉积涂层的标准规范
简介：
信息：ICS：25.220.40 CCS：发布：2009-09-01 实施：

JIS G7123-2000 生产镀锌板或电镀铬/氧化铬镀层钢的卷状冷轧黑钢板
简介：この規格は，JIS G 7121又はJIS G 7122に従う，ぶりき及び電解クロムノクロム酸化物めっき鋼板(以下，ECCSと記す。)の製造を目的とした，コイル状の一回及び二回冷間圧延ぶりき原板の要求事項について規定する。
信息：ICS：77.140.50 CCS：H40 发布：2000-01-20 实施：

ASTM B957/B957M-19 用于架空电导体的超高强度和超高强度镀锌（镀锌）钢芯线的标准规范
简介：
信息：ICS：77.140.65 CCS：发布：2019-03-01 实施：

ASTM B498/B498M-08 用于架空电导体的镀锌（镀锌）钢芯线的标准规范
简介：
信息：ICS：29.060.01 CCS：发布：2008-11-01 实施：

JIS G7122-2000 冷轧电镀铬/氧化铬镀层钢
简介：この規格は，シート状又は後でンートにカットするためのコイル状の，一回及びニ回冷間圧延電解クロムノクロム酸化物めっき鋼板(以下，ECCSという。)に対する要求事項について規定する。
信息：ICS：77.140.50 CCS：H40 发布：2000-01-20 实施：

ASTM B498/B498M-19 用于架空电导体的镀锌（镀锌）钢芯线的标准规范
简介：
信息：ICS：29.240.20 CCS：发布：2019-03-01 实施：

ASTM B957-08 用于架空电导体的超高强度和超高强度镀锌（镀锌）钢芯线的标准规范
简介：
信息：ICS：77.140.65 CCS：发布：2008-11-01 实施：

ASTM A677/A677M-99 无取向电钢全加工类型的标准规范
简介：
信息：ICS：77.140.50 CCS：发布：1999-12-10 实施：

ASTM B957/B957M-16 用于架空电导体的超高强度和超高强度镀锌（镀锌）钢芯线的标准规范
简介：
信息：ICS：77.140.65 CCS：发布：2016-12-01 实施：

ASTM B957/B957M-08e1 用于架空电导体的超高强度和超高强度镀锌（镀锌）钢芯线的标准规范
简介：
信息：ICS：77.140.65 CCS：发布：2008-11-01 实施：

ASTM B200-85(1999) 铅和铅锡合金在钢和铁合金上的电沉积涂层的标准规范
简介：
信息：ICS：25.220.40 CCS：发布：1999-03-10 实施：

ASTM B498/B498M-08(2016) 用于架空电导体的镀锌（镀锌）钢芯线的标准规范
简介：
信息：ICS：29.240.20 CCS：发布：2016-10-01 实施：

ASTM A677-07 无取向电钢全加工类型的标准规范
简介：
信息：ICS：77.140.50 CCS：发布：2007-11-01 实施：

ASTM B633-98e1 锌和锌钢电沉积涂层标准规范
简介：
信息：ICS：25.220.40 CCS：发布：1998-11-10 实施：

ASTM A677-16 无取向电钢全加工类型的标准规范
简介：
信息：ICS：77.140.50 CCS：发布：2016-04-01 实施：

ASTM B633-07 锌和锌钢电沉积涂层标准规范
简介：
信息：ICS：25.220.40 CCS：发布：2007-01-15 实施：

ASTM B633-98 锌和锌钢电沉积涂层标准规范
简介：
信息：ICS： CCS：发布：1998-11-10 实施：

ASTM B957/B957M-2016 架空电导线用过高强度和超高强度镀锌(镀锌的)钢芯线的标准规格
简介：1.1x00a0;This specification covers round, extra-high-strength and ultra-high-strength, Class A zinc-coated (galvanized), steel core wire used for use in Overhead Electrical Conductors. 1.2x00a0;This specification covers wire of diameter from 0.0500 to 0.1900 in. inclusive or 1.27 to 4.82 mm inclusive. 1.3x00a0;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：77.140.65 CCS：F21 发布：2016 实施：

ASTM B869-2007(2013) 有线电视(CATV)停经片用包铜钢电导线的标准规格
简介：1.1x00a0;This specification covers 218201;% conductivity hard-drawn round copper-clad steel wire for coaxial cable center conductors (Note 1). Note 1x2014;Wire ordered to this specification is not intended for redrawing since it is furnished in the hard-drawn temper. If wire is desired for the purpose, the manufacturer should be consulted. 1.2x00a0;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
信息：ICS：29.060.10 (Wires) CCS：K11 发布：2007 实施：

ASTM B869-1996 用于CATV用户引线的包铜钢电导线的标准规范
简介：1.1 This specification covers 21% conductivity hard-drawn round copper-clad steel wire for coaxial cable center conductors (Note 1). Note 1-Wire ordered to this specification is not intended for redrawing since it is furnished in the hard-drawn temper. If wire is desired for the purpose, the manufacturer should be consulted. 1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
信息：ICS：29.060.10 (Wires) CCS：K12 发布：1996 实施：

ASTM B633-15 锌和锌钢电沉积涂层标准规范
简介：
信息：ICS：25.220.40 CCS：发布：2015-12-01 实施：

ASTM B869-2007 共用天线电视(CATV)停经片用包铜钢电导线的标准规范
简介：1.1 This specification covers 21 % conductivity hard-drawn round copper-clad steel wire for coaxial cable center conductors (Note 1). Note 1 - Wire ordered to this specification is not intended for redrawing since it is furnished in the hard-drawn temper. If wire is desired for the purpose, the manufacturer should be consulted.1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
信息：ICS：29.060.10 (Wires) CCS：K11 发布：2007 实施：

NF A05-650-1993 电化学防腐保护.因离散工业电流产生的电影响的测量和中和.埋地或水下镀层刚或无镀层钢钢管管线以及同化金属制品
简介：Electrochemical anticorrosion protection - Measurement and neutralization of the electrical influences due to stray industrial currents - Buried or immersed coated or uncoated steel tubing pipelines as well as the assimilated metallic works
信息：ICS： CCS：A29 发布：1993-07-01 实施：

ASTM B200-85(2015) 铅和铅锡合金在钢和铁合金上的电沉积涂层的标准规范
简介：
信息：ICS：25.220.40 CCS：发布：2015-03-01 实施：

SAE AMS 5719D-2006 11.8Cr 2.5Ni 1.8Mo 0.33V (0.08-0.15C)退火、真空电弧或电渣熔融的耐腐蚀钢棒材、线材、锻件、管材、环形材和挤压件
简介：This specification covers a premium aircraft-quality corrosion-resistant steel in the form of bars, wire, forgings, mechanical tubing, flash welded rings, extrusions, and stock for forging, flash welded rings, or extruding. These products are used typically for parts, such as compressor wheels and structural members, requiring high strength and oxidation resistance up to 800 °F (427 °C), but usage is not limited to such applications.
信息：ICS：49.025.10 CCS：H40;V11 发布：2006-09-01 实施：

NBN-EN 10202-1992 冷轧电镀铬/氧化铬镀层钢
简介：
信息：ICS： CCS：发布：1992-6-23 实施：

EN 4721-2014 航空航天系列.钢X4crnimo16-5-1（1.4418）.熔炼和电渣重熔（ESR）.硬化和回火.巴.De <= 200 mm.900 MPa <= Rm 1050 MPa
简介：This European Standard specifies the requirements relating to: Steel X4CrNiMo16-5-1 (1.4418), air melted and electroslag remelted (ESR), hardened and tempered, bar, De
信息：ICS：49.025.10 CCS：V11 发布：2014-10 实施：

SAE AMS 5925A-2006 15.5Cr 1.8Mo 0.20N (0.37 - 0.45 C)电渣重熔的耐腐蚀钢棒材、线材和锻件
简介：This specification covers a premium aircraft-quality, corrosion-resistant steel in the form of bars, wire, forgings, and forging stock. These products have been used typically for anti-friction bearing components requiring resistance to both corrosion and wear with hardness not lower than 58 HRC after hardening and tempering, but usage is not limited to such applications.
信息：ICS：49.025.10 CCS：V11 发布：2006-08-01 实施：

ISO 9556-1989 钢和铁.全碳量的测定.电感应炉中燃烧后红外线吸收法
简介：The method is applicable to carbon contents between 0,003% (m/m) and 4,5 % (m/m). Specifies principle, reagents, apparatus, sampling, procedure, expression of results and test report. The annexes give additional information on the international co-operative tests, a graphical representation of precision data and features of induction furnaces and carbon analysers.
信息：ICS：77.040.30 CCS：H11 发布：1989-07 实施：1989-07-15

EN 4720-2014 航空航天系列.钢X4crnimo16-5-1（1.4418）.熔炼和电渣重熔（ESR）.硬化和回火.巴.De <= 200 mm.1150 MPa <= Rm 1300 MPa
简介：This European Standard specifies the requirements relating to: Steel X4CrNiMo16-5-1 (1.4418), air melted and electroslag remelted (ESR), hardened and tempered, Bar, De
信息：ICS：49.025.10 CCS：V11 发布：2014-10 实施：

SAE AMS 6447F-2006 1.45Cr (0.98-1.10C)(SAE 52100)电渣重熔的钢棒材、锻件和管件
简介：This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock. These products have been used typically for bearing components requiring a through- hardening steel usually with hardness of approximately 60 HRC, section thickness under 0.50 inch (12.7 mm), and subject to very rigid inspection standards, but usage is not limited to such applications.
信息：ICS：49.025.10 CCS：H40 发布：2006-05-01 实施：

ISO 8110-1-1988 一次冷轧电镀铬/氧化铬的钢.第1部分:板材
简介：
信息：ICS：6035 CCS：H46 发布：1988-10 实施：1988-10-01

JB/T 11837-2014 大型曲轴电渣钢熔铸件技术条件
简介：本标准规定了主轴颈直径在160 mm~350 mm的大型曲轴电渣钢熔铸件的订货要求、制造工艺、技术要求、检验规则和试验方法、质量证明书、标志、包装和运输。本标准适用于主轴颈直径在160 mm~350 mm的大型曲轴电渣钢熔铸件的订货、制造、检验和验收。
信息：ICS：77.140.80 CCS：J31 发布：2014-05-06 实施：2014-10-01

SAE AMS 6277F-2006 符合SAE 8620规定的0.50Cr 0.55Ni 0.25Mo(0.18～0.23C)真空电弧或电渣重熔的钢合金棒、锻件和管件
简介：This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock. These products have been used typically for carburized parts requiring high minimum core hardness in sections 0.375 inch (9.52 mm) and under in nominal thickness, and which are subject to rigid magnetic particle standards, but usage is not limited to such applications. The core may or may not be machinable after hardening.
信息：ICS：49.025.10 CCS：V11 发布：2006-05-01 实施：

NBN C 27-002-1972 液态和气态电介质，关于绝缘油的电钢度的限定方法
简介：
信息：ICS： CCS：发布：1972-5-8 实施：

ASTM B633-13 锌和锌钢电沉积涂层标准规范
简介：
信息：ICS：25.220.40 CCS：发布：2013-05-15 实施：

ASTM A677-05 无取向电钢全加工类型的标准规范
简介：
信息：ICS：77.140.50 CCS：发布：2005-06-15 实施：

MSZ 17711-1969 电设备切割机的钢导线
简介：
信息：ICS： CCS：发布：1969-01-01 实施：

SAE AMS 6548-2013 高级航空品质电渣再熔化或自耗电极真空电弧再熔化钢棒,钢锻件和钢管1.0Cr 3.2Ni 0.2Mo (0.12 - 0.17C)
简介：This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
信息：ICS：49.025.10 CCS：V11 发布：2013-01-03 实施：

ASTM A677-05e1 无取向电钢全加工类型的标准规范
简介：
信息：ICS：77.140.50 CCS：发布：2005-06-15 实施：

ASTM B633-19 锌和锌钢电沉积涂层标准规范
简介：
信息：ICS：25.220.40 CCS：/ 发布：0000-00-00 实施：0000-00-00

SAE AMS 6408D-2013 电渣再熔化(ESR)或自耗电极真空电弧再熔化(VAR)退火钢制热加工用具,钢棒和钢锻件5.2Cr 1.5Mo 1.0V (0.35-0.45C) (H-13)
简介：This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, and forging stock. These products have been used typically for hotwork tooling or for parts requiring a steel capable of through-hardening to a minimum hardness of 50 HRC in section thicknesses up to 12 inches (305 mm) with relatively high levels of strength, fatigue resistance, ductility, and thermal stability for use in service from -100 to +1000 °F (-73 to 538 °C) and where such parts may require welding, but usage is not limited to such applications.
信息：ICS：49.025.10 CCS：V11 发布：2013-01-03 实施：

UL 797-2004 电金属管.钢
简介：
信息：ICS：29.120.10 CCS：H48;K14 发布：2004-06-30 实施：

ASTM B633-85e1 锌和锌钢电沉积涂层标准规范
简介：
信息：ICS： CCS：发布：实施：