全封闭风扇冷却式检测标准全封闭风扇冷却式-中析研究所检测

(CMA)

(CNAS)

(ISO)

(高新技术企业)

全封闭风扇冷却式相关标准参考信息

T/CAMS /CICEIA110-2022 内燃机塑料冷却风扇产品质量分等分级规范
简介：产品的质量分等分级技术指标及相应的检验方法、检验规则和等级评定等。
信息：ICS：27.020 CCS：C341 发布：2022-08-02 实施：2022-09-08

SAE J1342-2012 发动机冷却风扇传动系统的功率消耗测定用试验方法
简介：The technique outlined in this SAE Recommended Practice was developed as part of an overall program for determining and evaluating fuel consumption of heavy-duty trucks and buses, but is applicable to off highway vehicles as well. It is recommended that the specific operating conditions be carefully reviewed on the basis of actual installation data. Cooling requirements are affected by all heat exchangers that are cooled by the fan-drive system. These may include radiators, condensers, charge air coolers, oil coolers, and others. Because of the variation in size, shape, configuration, and mountings available in cooling fans and fan drive systems, specific test devices have not been included. Using known power/speed relationships for a given fan, this procedure can be used to calculate the fan drive system's power consumption for engine cooling systems using fixed ratio, viscous or speed modulating, and mechanical on/off fan drives including electronically activated fan drives. This power consumption may than be used in determining engine net power per SAE J1349. For fan power/speed relationships, refer to SAE J1339. The purpose of this document is to provide a recommended method for determining and comparing the power consumption of fan drives over a variety of operating conditions. The resulting power consumption data is useful in predicting the fuel consumption of engines using these fan drives and in comparing one fan drive to another on the basis of power consumption. There is no known comparable ISO specification.
信息：ICS：43.060.30 CCS：T14 发布：2012-06-19 实施：

JB/T 50198-2000 冷凝式内燃机冷却风扇产品质量分等
简介：
信息：ICS： CCS：J96 发布：2000-08-31 实施：2000-12-01

DB31/T 1252-2020 交流电动机冷却风扇节能改造技术指南
简介：
信息：ICS：27.010 CCS：F01 发布：2020-11-13 实施：2021-02-01

SAE J1390-2012 发动机冷却风扇结构分析
简介：Three levels of fan structural analysis are included in this practice: 1. Initial Structural Integrity, 2. in-vehicle Testing, 3. Durability Test Methods. The Initial Structural Integrity section describes analytical and test methods used to predict potential resonance and, therefore, possible fatigue accumulation. The In-vehicle (or machine) section enumerates the general procedure used to conduct a fan strain gage test. Various considerations that may affect the outcome of strain gage data have been described for the user of this procedure to adapt/discard depending on the particular application. The Durability Test Methods section describes the detailed test procedures that may be used depending on type of fan, equipment availability, and end objective. Each of the previous levels builds upon information derived from the previous level. Engineering judgment is required as to the applicability of each level to a different vehicle environment or a new fan design. This SAE Recommended Practice is applicable to medium and heavy-duty trucks, buses, construction equipment, industrial, and agricultural equipment. It does not necessarily include passenger cars and light trucks. The usage of nonmetallic construction necessitates areas of evaluation not required by metallic designs. Chief among these are temperature extremes, moisture content, impact resistance, chemical attack, material purity/homogeneity, and aging.weathering. Areas of evaluation affecting both metallic and nonmetallic fans, but requiring somewhat different approaches with nonmetallic parts, include natural frequency determination and durability testing. The purpose of this document is to identify the general methodology for the structural analysis of engine cooling fans, and to provide expanded information on subset practices within the general methodology, such that a user of this practice can adapt specific subsets related to a vehicle class.
信息：ICS：43.060.30 CCS：T14 发布：2012-01-09 实施：

JB/T 50138-1999 推土机用金属冷却风扇产品质量分等
简介：
信息：ICS： CCS：P97 发布：1999-12-30 实施：2000-06-01

JB/T 13987-2020 内燃机冷却风扇塑料护风圈技术条件
简介：
信息：ICS：27.020 CCS：J96 发布：2020-08-31 实施：2021-04-01

DIN V 42673-2-2010 全封闭风扇冷却式鼠笼三相异步电动机.带轴承的感应电动机B3、感应电动机B5和感应电动机B14的设计.第2部分:关联外框尺寸.增强安全"e"型防护设备的额定输出功率
简介：
信息：ICS：29.160.30 CCS：K22 发布：2010-05 实施：

JB/T 6723.3-1999 内燃机冷却风扇.第3部分：冷凝式内燃机冷却风扇.技术条件
简介：本标准规定了冷凝式内燃机冷却风扇的分类、命名、技术要求、检验规则以及标志、包装和贮存。本标准适用于冷凝式内燃机带发电机及不带发电机的两种冷却风扇。
信息：ICS： CCS：J96 发布：1999-09-17 实施：2000-01-01

JB/T 13596-2018 拖拉机冷却风扇
简介：
信息：ICS：65.060.10 CCS：T61 发布：2018-12-21 实施：2019-10-01

DIN V 42673-3-2010 全封闭风扇冷却式鼠笼三相异步电动机.带轴承的感应电动机B3、感应电动机B5和感应电动机B14的设计.第3部分:关联外框尺寸.防火"d"型外壳设备的额定输出功率
简介：
信息：ICS：29.160.30 CCS：K22 发布：2010-05 实施：

JB/T 6723.4-1999 内燃机冷却风扇.第4部分：冷凝式内燃机冷却风扇.试验方法
简介：本标准规定了冷凝式内燃机冷却风扇的试验项目、方法、内容、数据计算、结果分析以及文件整理的要求。本标准适用于冷凝式内燃机带发电机及不带发电机的两种冷却风扇。
信息：ICS： CCS：J96 发布：1999-09-17 实施：2000-01-01

T/ZZB 0396-2018 节能型商用车冷却风扇总成
简介：本标准规定了节能型商用车冷却风扇总成（以下简称节能风扇）的术语和定义、分类、代号和型号规格、基本要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存及质量承诺。本标准适用于商用车及商用车柴油机，外径为φ600mm～φ750mm的节能型塑料冷却风扇总成。
信息：ICS：27.020 CCS：C346 发布：2018-07-20 实施：2019-03-06

SAE J1339-2009 测量发动机冷却风扇功率消耗的试验方法
简介：This SAE Recommended Practice is intended for use in testing and evaluating the approximate performance of engine cooling fans. This performance would include flow, pressure, and power. This flow and pressure information is used to estimate the engine cooling performance. This power consumption is used to estimate net engine power per SAE J1349. The procedure also provides a general description of equipment necessary to measure the approximate fan performance. The test conditions in the procedure generally will not match those of the installation for which cooling and fuel consumption information is desired. The performance of a given fan depends on the geometric details of the installation, including the shroud and its clearance. These details should be duplicated in the test setup if accurate performance measurement is expected. The performance at a given air density and speed also depend on the volumetric flow rate, or the pressure rise across the fan, since these two parameters are mutually dependent. These parameters depend on the pressure drop across the radiator core and the ram pressure due to vehicle motion. For these reasons, the test procedure should be recognized as providing only an approximate measure of installed fan performance. Although the test procedure is based on running the fan with a motoring dynamometer, the actual installation can be used as a test fixture if an accurate torque meter is available. In this case, the same qualifications discussed apply. Finally, for the effect of a fan clutch in reducing fan use and power consumption, which is not a part of this procedure, refer to SAE J1342. This document provides a recommended test procedure for measuring and comparing the performance of fans over a range of pressure and speeds. The resulting performance data are intended for predicting the cooling performance and fuel consumption of engines using these fans, and in comparing one fan versus another.
信息：ICS：19.080;43.060.30 CCS：T14 发布：2009-09-03 实施：

ARMY MIL-F-62564 NOTICE 1-1998 涡轮风扇发动机冷却
简介：MlL-F-62564(AT) is inactive for new design and is no longer used, except for replacement purposes.
信息：ICS：27.020 CCS：J91 发布：1998-02-27 实施：

JB/T 6723.3-2018 内燃机冷却风扇第3部分：冷凝式内燃机冷却风扇技术条件
简介：
信息：ICS：27.02 CCS：J96 发布：2018-07-04 实施：2019-05-01

ANSI/IEEE 841-2009 石油和化学工业标准.全封闭风扇冷却式(TEFC)高效重载鼠笼式感应电动机.最高达370 kW(500 hp)
简介：The purpose of this standard is to define a specification that deals with mechanical and electrical performance, electrical insulation systems, corrosion protection, and electrical and mechanical testing for severe duty TEFC squirrel cage polyphase induction motors, up to and including 370 kW (500 hp), for petroleum and chemical industry application.
信息：ICS：29.160.30 CCS：K26 发布：2009 实施：

TB/T 2709-1996 内燃机车冷却风扇技术条件
简介：本标准规定了铁路内燃机车轴流式冷却风扇(简称冷却风扇)技术条件、试验方法、检查验收等。本标准适用于铁路内燃机车新造轴流式冷却风扇。
信息：ICS： CCS：S42 发布：1997-01-03 实施：1997-07-01

JB/T 6723.4-2018 内燃机冷却风扇第4部分：冷凝式内燃机冷却风扇试验方法
简介：
信息：ICS：27.02 CCS：J96 发布：2018-07-04 实施：2019-05-01

IEEE 841-2009 石油和化学工业用标准.最高达370kW(500hp)的全封闭风扇冷却式鼠笼式感应电动机
简介：This standard applies to premium-efficiency totally enclosed fan-cooled (TEFC), horizontal and vertical,single-speed, squirrel cage polyphase induction motors, up to and including 370 kW (500 hp), and 4000 Vnominal, in National Electrical Manufacturers Association (NEMA) frame sizes 143T and larger, forpetroleum, chemical, and other severe-duty applications (commonly referred to as premium-efficiencysevere-duty motors). Excluded from the scope of this standard are motors with sleeve bearings andadditional specific features required for explosion-proof motors.
信息：ICS：29.160.30 CCS：K20 发布：2009 实施：

WJ 2226-1994 风冷柴油机冷却风扇通用规范
简介：
信息：ICS： CCS：J72 发布：1994 实施：1995-06-01

JB/T 6723.1-2018 内燃机冷却风扇第1部分：金属冷却风扇技术条件
简介：
信息：ICS：27.02 CCS：J96 发布：2018-07-04 实施：2019-05-01

JB/T 6723.3-2008 内燃机冷却风扇.第3部分:冷凝式内燃机冷却风扇技术条件
简介：JB/T 6723的本部分规定了冷凝式内燃机冷却风扇的分类、命名、技术要求、检验规则以及标志。本部分适用于冷凝式内燃机带发电机及不带发电机的两种冷却风扇（以下总称风扇）。
信息：ICS：27.020 CCS：J96 发布：2008-06-04 实施：2008-11-01

NEN 3321-1993 旋转电机．全封闭风扇冷却型三相鼠笼式电动机的尺寸和额定输出功率
简介：De norm is van toepassing op uitwendig gekoelde draaistroom-kooiankermotoren voor spanningen tot en met 690 V met een frequentie van 50 Hz, bestemd voor continu bedrijf, in voet- en/of flensuitvoering.
信息：ICS： CCS：发布：1993-10 实施：1993-10

T/CCMA 0049-2017 土方机械冷却风扇声功率级的测定半消声室试验方法
简介：本标准规定了土方机械冷却风扇声功率级试验的术语和定义、要求、方法及数据处理。本标准适用于在半消声室内进行直径大于254mm且小于2135mm的　土方机械用冷却风扇声功率级的试验。
信息：ICS：53.100 CCS：C351 发布：2017-07-07 实施：2020-03-25

JB/T 6723.4-2008 内燃机.冷却风扇.第4部分:冷凝式内燃机冷却风扇试验方法
简介：JB/T 6723的本部分规定了冷凝式内燃机冷却风扇的试验项目、方法、内容、数据计算、结果分析以及文件整理的要求。本部分适用于冷凝式内燃机带发电机及不带发电机的两种冷却风扇（以下总称风扇）。
信息：ICS：27.020 CCS：J96 发布：2008-06-04 实施：2008-11-01

JB/T 6723.2-1993 内燃机冷却风扇.第二部分：塑料冷却风扇技术条件
简介：本标准规定了内燃机塑料冷却风扇产品分类，产品标记方法，技术要求，检验规则，标志、包装、运输及贮存。本标准适用于外径不大于750mm的水冷式、油冷式内燃机塑料冷却风扇。
信息：ICS： CCS：J96 发布：1993-07-29 实施：1994-01-01

BS EN 16430-3-2014 风扇辅助散热器, 对流散热器以及沟槽式对流散热器. 冷却能力的试验方法和等级评定
简介：
信息：ICS：91.140.10 CCS：Q83 发布：2014-12-31 实施：2014-12-31

JB/T 6723.2-2008 内燃机冷却风扇.第2部分:塑料冷却风扇.技术条件
简介：JB/T 6723的本部分规定了内燃机塑料冷却风扇产品分类、代号、产品型号规格标记方法、技术要求、检验方法、检验规则、标志、包装、运输及贮存。本部分适用于外径不大于1000mm的水冷式、风冷式内燃机(汽油机、柴油机)冷却系统用塑料冷却风扇(以下简称风扇)。
信息：ICS：27.020 CCS：J96 发布：2008-02-01 实施：2008-07-01

JB/T 6723.1-1993 内燃机冷却风扇.第一部分：金属冷却风扇技术条件
简介：本标准规定了内燃机金属冷却风扇产品分类，产品标记，技术要求，检验规则及标志、包装、运输、贮存的要求。本标准适用于外径不大于750mm的水冷式、油冷式内燃机金属冷却风扇。
信息：ICS： CCS：J96 发布：1993-07-29 实施：1994-01-01

JB/T 6723.1-2008 内燃机冷却风扇.第1部分:金属冷却风扇.技术条件
简介：JB/T 6723的本部分规定了内燃机金属冷却风扇产品分类、代号、产品型号规格标记方法、技术要求、检验方法、检验规则、标志、包装、运输及贮存。本部分适用于外径不大于750mm的水冷式、风冷式内燃机(汽油机、柴油机)冷却系统用金属冷却风扇(以下简称风扇)。
信息：ICS：27.020 CCS：J96 发布：2008-02-01 实施：2008-07-01

TIS 978-1990 汽车用发动机冷却风扇标准
简介：
信息：ICS： CCS：发布：1990-06-26 实施：

EN 16430-3-2014 有风扇辅助的散热器,对流散热器及沟槽对流散热器.第3部分:对冷却能力的测试方法及评价等级
简介：This European Standard applies to the testing of the dry cooling capacity with no condensation of fan assisted radiators, convectors and trench convectors which are factory assembled or kits, i.e. - fan assisted radiators and convectors, provided the cooler has a dedicated fan or fans; - radiators and convectors without dedicated fan(s); - trench convectors with and without fan(s), provided the cooler and the fan(s) are dedicated.
信息：ICS：91.140.10 CCS：J96 发布：2014-12 实施：

TB/T 2709-2007 内燃机车用冷却风扇
简介：本标准规定了内燃机车用轴流式冷却风扇（以下简称冷却风扇）的技术要求、试验方法、检验规则以及标志、包装、运输、贮存等要求。本标准适用于内燃机车用新造冷却风扇。内燃动车及发电机组用冷却风扇也可参照本标准执行。
信息：ICS：45.060.10 CCS：S42 发布：2007-04-23 实施：2007-10-01

ARMY MIL-F-62564-1988 涡轮风扇发动机冷却
简介：This specification covers a vaneaxial fan which is acomponent of the engine cooling system in ground combat vehicles.axial fan will be referred to by the term "fan"(see 6.1).The vane
信息：ICS：27.020 CCS：J91 发布：1988-04-28 实施：

SAE J2867-2014 轻型汽车电动冷却风扇组件的气流性能的实验室测试
简介：This SAE Recommended Practice is intended for use in testing and evaluating the performance of Light Duty automotive electric engine cooling fans. These Electric Cooling Fan (ECF) Assemblies are purchased by Light Duty Truck and Passenger Car OEM's from suppliers. They are purchased as complete assemblies, consisting of the fan(s), motor(s), and shroud (see Figure 1); this Recommended Practice will only consider such complete assemblies. Some purchased assemblies using brush-type motors may also include control devices such as power resistors or pulse width modulation (PWM) electronics for speed control. In the case of brushless motor technology, the contro
信息：ICS：43.040.10 CCS：发布：2014-08-28 实施：

DLA A-A-50506 A VALID NOTICE 2-2006 冷却电子设备用微型轴流式风扇
简介：A-A-50506A, dated 06 August 2001, has been reviewed anddetermined to be valid for use in acquisition.
信息：ICS：49.060 CCS：V76 发布：2006-06-14 实施：

DIN 42673-3-1983 IMB3型带滚动轴承全密封风扇冷却鼠笼三相感应电机.相关框架尺寸.防火外壳"d"型输出功率
简介：Totally enclosed fan-cooled three-phase induction motors with squirrel-cage, type IM B 3, with rolling bearings; relationship frame sizes - output ratings for type of protection flameproof enclosure ?dZusammenhang mit dem vom Europ?ischen Komitee für El
信息：ICS：29.160.30 CCS：K22 发布：1983-04 实施：

SAE AS 194B-2014 命名.发动机冷却风扇
简介：This Aerospace Standard (AS) covers the requirements for polytetrafluoroethylene (PTFE) hose assemblies for use in aerospace hydraulic fuel, and lubricating oil systems at temperatures between -67 degrees F and 450 degrees F for Class I assemblies, -67 degrees F and 275 degrees F for Class II assemblies, and at nominal pressures up to 1500 psi. The hose assemblies are also suitable for use within the same temperature and pressure limitations in aerospace pneumatic systems where some gaseous diffusion through the wall of the PTFE liner can be tolerated. The use of these hose assemblies in pneumatic storage systems is not recommended. In addition, installatio
信息：ICS：01.040.49;49.050 CCS：V31 发布：2014-08-12 实施：

SN/T 1669-2005 进出口汽车用电动冷却风扇检验规程
简介：本标准规定了进出口汽车用电动冷却风扇的技术要求、检验及判定。本标准适用于额定电压为12V的汽车用电动冷却风扇。对评价电动冷却风扇性能的各项参数的额定值，本标准不作规定。本标准应与产品相关的技术条件一起使用，本标准未规定的其他要求，可参照产品相关的技术条件。
信息：ICS： CCS：T36 发布：2005-09-30 实施：2006-05-01

DIN 42673-2-1983 IMB3型带滚动轴承全密封风扇冷却鼠笼三相感应电机.相关框架尺寸.防爆高安全"E"型输出功率
简介：Totally enclosed fan-cooled three-phase induction motors with squirrel-cage, type IM B3, with rolling bearings; relationship frame sizes - output ratings for type of protection increased safety ?eZusammenhang mit dem vom Europ?ischen Komitee für Elektro
信息：ICS：29.160.30 CCS：K22 发布：1983-04 实施：

QB/T 4676-2014 蒸发式冷风扇用冷却填料
简介：本标准规定了蒸发式冷风扇用冷却填料的术语和定义、产品分类与型号命名、要求、试验方法、检验规则、标志、包装、运输和贮存。本标准适用于通过水蒸发进行降温、加湿的家用和类似用途蒸发式冷风扇用纤维类冷却填料(以下简称“填料”)。
信息：ICS：97.030 CCS：Y61 发布：2014-07-09 实施：2014-11-01

SAE J1390-2003 发动机冷却风扇结构分析
简介：Three levels of fan structural analysis are included in this practice: (a) Initial Structural Integrity (b) in-vehicle Testing (c) Durability Test Methods. The Initial Structural Integrity section describes analytical and test methods used to predict potential resonance and, therefore, possible fatigue accumulation. The In-vehicle (or machine) section enumerates the general procedure used to conduct a fan strain gage test. Various considerations that may affect the outcome of strain gage data have been described for the user of this procedure to adapt/discard depending on the particular application. The Durability Test Methods section describes the detailed test procedures that may be used depending on type of fan, equipment availability, and end objective. Each of the previous levels builds upon information derived from the previous level. Engineering judgment is required as to the applicability of each level to a different vehicle environment or a new fan design. This SAE Recommended Practice is applicable to medium and heavy-duty trucks, buses, construction equipment, industrial, and agricultural equipment. It does not necessarily include passenger cars and light trucks. The purpose of this document is to identify the general methodology for the structural analysis of engine cooling fans, and to provide expanded information on subset practices within the general methodology, such that a user of this practice can adapt specific subsets related to a vehicle class.
信息：ICS：43.060.30 CCS：T14 发布：2003-04-01 实施：

DIN 42677-3-1983 带滚动轴承的IM B 5、 IMB10、IMB14型全密封风扇冷却鼠笼式三相感应电机.相关框架规格－防火外壳体“d"型的额定输出功率
简介：
信息：ICS：29.160.30 CCS：K22 发布：1983-04 实施：

JB/T 6723.2-2014 内燃机冷却风扇第2部分:塑料冷却风扇技术条件
简介：JB/T 6723的本部分规定了内燃机塑料冷却风扇的产品分类、代号、产品型号规格标记方法、技术要求、检验方法、检验规则、标志、包装、运输和贮存。本部分适用于外径不大于φ 1 000 mm的水冷式、风冷式内燃机（汽油机、柴油机）冷却系统用塑料冷却风扇总成（以下简称风扇）。
信息：ICS：27.020 CCS：J96 发布：2014-05-06 实施：2014-10-01

JB/T 9545-2002 变压器冷却风扇用三相异步电动机技术条件
简介：本标准规定了YBF系列变压器冷却风扇用三相异步电动机的型式、基本参数及尺寸、技术要求、试验方法与检验规则以及标志、包装、运输与贮存的要求。本标准适用于YBF系列变压器冷却风扇用三相异步电动机。
信息：ICS：29.160 CCS：K20 发布：2002-12-27 实施：2003-04-01

DIN 42677-2-1983 带滚动轴承的IM B 5、 IMB10、IMB14型全密封风扇冷却鼠笼式三相感应电机.相关框架规格－提高防护安全性"E"型的额定输出功率
简介：
信息：ICS：29.160.30 CCS：K22 发布：1983-04 实施：

JB/T 9545-2013 变压器冷却风扇用三相异步电动机技术条件
简介：本标准规定了YBF系列变压器冷却风扇用三相异步电动机的型式、基本参数与尺寸、技术要求、试验方法、检验规则、标志、包装、运输与贮存的要求。本标准适用于YBF系列变压器冷却风扇用三相异步电动机(以下简称电动机),凡属于本系列电动机所派生的其他类似用途各种电动机也可参照执行。
信息：ICS：29.160.30 CCS：K22 发布：2013-12-31 实施：2014-07-01

IEEE 841 INT 1-2-2002 IEEE Std 841™-1994用IEEE标准解释文件.石油和化学工业强重型完全闭合式风扇冷却(TEFC)的小于等于500 hp贮藏笼感应电动机用IEEE标准
简介：IEEE Standards InterpretationforIEEE Std 841™-1994IEEE Standard for the Petroleum andChemical Industry-Severe Duty TotallyEnclosed Fan-Cooled (TEFC) Squirrel CageInduction Motors-Up to and Including 500 hp
信息：ICS： CCS：J73 发布：2002-10-09 实施：

DLA A-A-50506 A-1982 冷却电子设备用微型轴流式风扇
简介：The General Services Administration has authorized the use of this commercial item description as a replacement for Military Specifications MIL-V-16720E and MIL-V-16721D which are cancelled.
信息：ICS：49.060 CCS：V76 发布：1982 实施：

JB/T 7697-2013 工程机械用金属冷却风扇技术条件
简介：本标准规定了工程机械用金属冷却风扇的分类、要求、试验方法、检验规则、标志、包装和贮存。本标准适用于直径大于254 mm的工程机械用金属冷却风扇。
信息：ICS：53.100 CCS：P97 发布：2013-04-25 实施：2013-09-01

DLA A-A-50506 A VALID NOTICE 1-2001 冷却电子设备用微型轴流式风扇
简介：A-A-50506A, dated 0 DECEMBER 1982, has been reviewed and determinedto be valid for use in acquisition.
信息：ICS：49.060 CCS：V76 发布：2001-08-06 实施：

SAE AS 194-1945 命名.发动机冷却风扇(对1973年8月9日之后的新型设计暂停使用)
简介：This Aerospace Standard (AS) covers the requirements for polytetrafluoroethylene (PTFE) hose assemblies for use in aerospace hydraulic fuel, and lubricating oil systems at temperatures between -67 degrees F and 450 degrees F for Class I assemblies, -67 degrees F and 275 degrees F for Class II assemblies, and at nominal pressures up to 1500 psi. The hose assemblies are also suitable for use within the same temperature and pressure limitations in aerospace pneumatic systems where some gaseous diffusion through the wall of the PTFE liner can be tolerated. The use of these hose assemblies in pneumatic storage systems is not recommended. In addition, installations in which the limits specified herein are exceeded, or in which the application is not covered specifically by this standard, for example oxygen, shall be subject to the approval of the purchaser.
信息：ICS：49.050 CCS：V31 发布：1945-01-01 实施：

TB/T 2709-2013 内燃机车用冷却风扇
简介：本标准规定了内燃机车用冷却风扇(以下简称“冷却风扇”)的环境条件、技术要求、检验方法、检验规则、RAMS要求、标志、包装、运输和储存。本标准适用于内燃机车用新造冷却风扇。内燃动车用新造冷却风扇可参照本标准执行。
信息：ICS：29.280 CCS：S42 发布：2013-03-13 实施：2013-07-01

JB/T 7697-2001 工程机械用金属冷却风扇.技术条件
简介：JB/T 7697-2001 本标准是对JB/T 7697-1995《推土机用金属冷却风扇技术条件》的修订。修订时增加了产品型号与规格，风扇叶片磁力探伤的工艺检测；补充了噪声等技术指标的试验方法和检验规则的内容。本标准规定了工程机械用金属冷却风扇的产品分类，技术要求，试验方法，检验规则及标志、包装、贮存。本标准适用于外径大于600mm的工程机械用金属冷却风扇。本标准于1995的首次发布，本次是第一次修订。
信息：ICS：91.220 CCS：P97 发布：2001-04-03 实施：2001-10-01

JB/T 6723.4-2018 内燃机冷却风扇.第4部分：冷凝式内燃机冷却风扇.试验方法
简介：本标准规定了冷凝式内燃机冷却风扇的试验项目、方法、内容、数据计算、结果分析以及文件整理的要求。本标准适用于冷凝式内燃机带发电机及不带发电机的两种冷却风扇。
信息：ICS： CCS：J96 发布：0000-00-00 实施：0000-00-00

DIN SPEC 42673-4-2012 全封闭风扇冷却鼠笼式三相异步电机.带有轴承的IM B3,IM B5,IM B14的设计.外壳最大尺寸规格
简介：
信息：ICS：29.160.30 CCS：K22 发布：2012-07 实施：

IEEE 841-2001 石油和化学工业.最高达370kW(500hp)的全封闭风扇冷却式重载鼠笼式感应电动机
简介：Covers mechanical and electrical design, electrical insulation systems, corrosion protection, and electrical and mechanical testing for severe-duty squirrel-cage polyphase induction motors for chemical industry applictions. Applies to high-efficiency, totally enclosed fan-cooled (TEFC), horizontal and vertical, single-speed, squirrel-cage polyphase induction motors, up to and including 370 kW (500 hp), in NEMA frame sizes 143T and larger, for petroleum, chemical, and other severe duty applications (commonly referred to as severe duty motors).
信息：ICS：29.160.30 CCS：K20 发布：2001 实施：

JB/T 6723.3-2018 内燃机冷却风扇.第3部分：冷凝式内燃机冷却风扇.技术条件
简介：本标准规定了冷凝式内燃机冷却风扇的分类、命名、技术要求、检验规则以及标志、包装和贮存。本标准适用于冷凝式内燃机带发电机及不带发电机的两种冷却风扇。
信息：ICS： CCS：J96 发布：0000-00-00 实施：0000-00-00