IEC-60331检测标准IEC-60331-中析研究所检测

(CMA)

(CNAS)

(ISO)

(高新技术企业)

IEC-60331相关标准参考信息

GOST IEC 60331-2-2021
简介：
信息：ICS：13.220.40 CCS：发布：2021-00-00 实施：2022-01-01

IEC 60331-3 (REDLINE + STANDARD)-2018
简介：
信息：ICS：/ CCS：/ 发布：2018-03-01 实施：2018-03-30

IEC 60331-11:1999+AMD1:2009 CSV 着火条件下电缆的试验.电路完整性.第11部分:设备.在至少750°C的火焰温度下单独着火
简介：
信息：ICS：29.060.20 CCS：发布：2009-07-08 实施：

GOST IEC 60331-3-2021
简介：
信息：ICS：13.220.40 CCS：发布：2021-00-00 实施：2022-01-01

VDE 0482-331-21-2017 Tests for electric cables under fire conditions - Circuit integrity - Part 21: Procedures and requirements - Cables of rated voltage up to and including 0@6/1@0 kV (IEC 60331-21:1999)
简介：
信息：ICS：/ CCS：/ 发布：2017-06-01 实施：2017-05-27

IEC 60331-11-1999+AMD1-2009 CSV 着火条件下电缆的试验.电路完整性.第11部分:设备.在至少750°C的火焰温度下单独着火
简介：
信息：ICS：29.060.20 CCS：发布：2009-07-08 实施：

GOST IEC 60331-1-2021
简介：
信息：ICS：13.220.40 CCS：发布：2021-00-00 实施：2022-01-01

KS C IEC 60331-21-2015 着火条件下电缆的试验.线路完整性.第21部分:过程和要求.额定电压达到和包括0.6/1.0kV的电缆？
简介：
信息：ICS：13.220.40;29.020;29.060.20 CCS：K13 发布：2015-08-04 实施：

IEC 60331-11-2009 Essais pour c?bles électriques soumis au feu – Intégrité des circuits – Partie 11: Appareillage – Incendie seul avec flamme à une température d’au moins 750 degré C (Edition 1.1 Consolidated Reprint)
简介：This part of IEC 60331 specifies the test apparatus to be used for testing cables required to maintain circuit integrity when subject to fire alone where the test condition is based upon a flame with a controlled heat output corresponding to a temperature of at least 750 ??It also provides in annex A the method of verification of the burner and control system used for the test.
信息：ICS：/ CCS：/ 发布：2009-07-01 实施：2009-07-13

KS C IEC 60331-11-2019 着火条件下电缆的试验.电路完整性.第11部分:仪器.在至少750℃的火焰温度下单独着火
简介：
信息：ICS： CCS：发布：2019-12-31 实施：

KS C IEC 60331-21-2015(2020) 着火条件下电缆的试验电路完整性第21部分:额定电压0.6/1.0kV及以下电缆的规程和要求
简介：
信息：ICS： CCS：发布：2015-08-04 实施：

IEC 60331-11 Edition 1.1-2009 电缆在着火条件下的试验.电路完整性.第11部分:仪器.火焰温度等于高于750 °C时的孤立火焰
简介：
信息：ICS：13.220.40;29.020;29.060.20 CCS：K13 发布：2009-07 实施：

IEC 60331-2:2018 着火条件下电缆的试验.电路完整性.第2部分:额定电压0.6/1.0千伏及以下电缆在至少830℃温度下的冲击着火试验方法
简介：
信息：ICS：13.220.40 CCS：发布：2018-03-28 实施：

KS C IEC 60331-3-2014(2019) 着火条件下电缆的试验.电路完整性.第3部分:在金属外壳中试验的额定电压0.6/1.0kV及以下的电缆在至少830℃温度下的冲击着火的试验方法
简介：
信息：ICS： CCS：发布：2014-10-03 实施：

IEC 60331-1:2009 着火条件下电缆的试验.电路完整性.第1部分:额定电压0.6/1.0千伏及以下总直径超过20毫米的电缆在至少830℃的温度下受冲击着火的试验方法
简介：
信息：ICS：13.220.40 CCS：发布：2009-05-19 实施：

IEC 60331-1-2018 RLV 着火条件下电缆的试验.电路完整性.第1部分:额定电压0.6/1.0 kV及以下总直径超过20 mm的电缆在至少830°C温度下冲击着火的试验方法
简介：
信息：ICS：13.220.40 CCS：发布：2018-03-28 实施：

KS C IEC 60331-1-2013 在火焰条件下电缆的线路完整性试验.第1部分:额定电压0.6/1.0kV及以下、总直径大于20mm电缆在温度不低于830℃冲击火焰下的试验方法
简介：KS C IEC 60331의 제1부는 시험 장치 및 절차를 규정하고 정격 전압이 최대 0.6/1.0 kV인 저전압 전력 케이블과 규정 조건 하에 화재 및 기계 충격을 받을 때 회로 보존성을 유지하기 위해 요구되는정격 전압을 가진 제어 케이블에 대해 권장되는 화염 적용 시간을 포함하여 성능 요구조건을 수록한다. 이 표준은 완성 바깥지름이 20 mm를 초과하는 케이블에 대하여 적용한다.이 표준은 시편 준비 방법, 연속성 점검 배열, 전기 시험 절차, 케이블 연소 방법, 충격 발생 방법을설명하고 시험 결과 평가를 위한 요구조건을 제공한다.부속서 A는 시험에 이용되는 버너 및 제어 계통의 검증 방식을 설명한다.이 표준의 준수 여부를 나타내기 위해 케이블에 마킹할 수도 있는 식별 요구조건을 명시한다.
信息：ICS：29.060.20 CCS：K01 发布：2013-09-18 实施：2013/9/18

IEC 60331-11:1999/AMD1:2009 修改件1.着火条件下电缆的试验.电路完整性.第11部分:仪器.在至少750°C的火焰温度下单独着火
简介：
信息：ICS：13.220.40 CCS：发布：2009-05-19 实施：

IEC 60331-3:2018 RLV 着火条件下电缆的试验.电路完整性.第3部分:在金属外壳中试验的额定电压0.6/1.0 kV及以下电缆在至少830°C温度下冲击着火的试验方法
简介：
信息：ICS：13.220.40 CCS：发布：2018-03-28 实施：

IEC 60331-2:2009 耐火条件下的电缆测试 - 电路完整性 - 第2部分:对于额定电压高达并包括0,6/1.0 kV的电缆在至少830°C的温度下具有冲击的火灾测试方法直径不超过20毫米
简介：
信息：ICS：13.220.40 CCS：发布：2009-05-19 实施：

IEC 60331-1:2018 RLV 着火条件下电缆的试验.电路完整性.第1部分:额定电压0.6/1.0 kV及以下总直径超过20 mm的电缆在至少830°C温度下冲击着火的试验方法
简介：
信息：ICS：13.220.40 CCS：发布：2018-03-28 实施：

KS C IEC 60331-2-2013(2018) 着火条件下电缆的试验电路完整性第2部分:额定电压0.6/1.0kV及以下、总直径不超过20mm的电缆在830℃以上温度冲击着火的试验方法
简介：
信息：ICS：29.060.20 CCS：发布：2013-09-18 实施：

IEC 60331-3:2009 着火条件下电缆的试验.电路完整性.第3部分:电缆在至少830℃温度下冲击着火的试验方法额定电压小于等于0.6/1.0 kV 在金属外壳中进行试验
简介：
信息：ICS：13.220.40 CCS：发布：2009-05-19 实施：

IEC 60331-3-2018 着火条件下电缆的试验.电路完整性.第3部分:电缆在至少830℃温度下冲击着火的试验方法额定电压小于等于0.6/1.0 kV 在金属外壳中进行试验
简介：
信息：ICS：13.220.40 CCS：发布：2018-03-28 实施：

KS C IEC 60331-2-2013 在火焰条件下电缆的线路完整性试验.第2部分:额定电压0.6/1.0kV及以下、总直径不大于20mm电缆在温度不低于830℃冲击火焰下的试验方法
简介：KS C IEC 60331의 제2부는 시험 장치 및 절차를 규정하고 정격 전압이 최대 0.6/1.0 kV인 저전압 전력 케이블과 규정 조건 하에 화재 및 기계 충격을 받을 때 회로 보존성을 유지하기 위해 요구되는정격 전압을 가진 제어 케이블에 대해 권장되는 화염 적용 시간을 포함하여 성능 요구사항을 수록한다. 이 표준은 완성 바깥지름이 20 mm를 초과하지 않는 케이블에 대하여 적용한다.이 표준은 시편 준비 방법, 회로연결 검사 장치, 전기 시험 절차, 케이블 연소 방법, 충격 발생 방법을 설명하고 시험 결과 평가를 위한 요구사항을 제공한다.부속서 A는 시험에 이용되는 버너 및 제어 시스템의 인증 방식을 설명한다.이 표준의 준수 여부를 나타내기 위해 케이블에 마킹할 수도 있는 식별 요구사항을 명시한다.
信息：ICS：29.060.20 CCS：K01 发布：2013-09-18 实施：2013-09-18

IEC 60331-11-1999/AMD1-2009 修改件1.着火条件下电缆的试验.电路完整性.第11部分:仪器.在至少750°C的火焰温度下单独着火
简介：
信息：ICS：13.220.40 CCS：发布：2009-05-19 实施：

IEC 60331-2-2018 RLV 着火条件下电缆的试验.电路完整性.第2部分:额定电压0.6/1.0 kV及以下总直径不超过20 mm的电缆在至少830°C温度下冲击着火的试验方法
简介：
信息：ICS：13.220.40 CCS：发布：2018-03-28 实施：

IEC 60331-11 AMD 1-2009 AMENDEMENT 1 Essais pour c?bles électriques soumis au feu – Intégrité des circuits – Partie 11: Appareillage – Incendie seul avec flamme à une température d’au moins 750 degrés C (Edition 1.0)
简介：This part of IEC 60331 specifies the test apparatus to be used for testing cables required to maintain circuit integrity when subject to fire alone where the test condition is based upon a flame with a controlled heat output corresponding to a temperature of at least 750 ??It also provides in annex A the method of verification of the burner and control system used for the test.
信息：ICS：/ CCS：/ 发布：2009-05-01 实施：2009-07-13

IEC 60331-3-2018 RLV 着火条件下电缆的试验.电路完整性.第3部分:在金属外壳中试验的额定电压0.6/1.0 kV及以下电缆在至少830°C温度下冲击着火的试验方法
简介：
信息：ICS：13.220.40 CCS：发布：2018-03-28 实施：

KS C IEC 60331-1-2013(2018) 着火条件下电缆的试验电路完整性第1部分:额定电压0.6/1.0kV及以下、总直径大于20mm的电缆在830℃以上温度冲击着火的试验方法
简介：
信息：ICS：29.060.20 CCS：发布：2013-09-18 实施：

IEC 60331-3-2009 Essais pour c?bles électriques soumis au feu – Intégrité des circuits – Partie 3: Méthode d’essai au feu pour les c?bles de tension assignée au plus égale à 0@6/1@0 kV@ essayés sous conduit métallique avec chocs@ à une température d’au moins 830 degrés C
简介：This part of IEC 60331 specifies the test procedure and gives the performance requirement@ including a recommended flame application time@ for cables of rated voltage up to and including 0@6/1@0 kV required to maintain circuit integrity when subjected to fire and mechanical shock under specified conditions. It is intended for use when testing cables of greater than 20 mm overall diameter. It describes the means of sample preparation@ the continuity checking arrangements@ the electrical testing procedure@ the method of burning the cables and the method of shock production@ and gives requirements for evaluating test results. This part of IEC 60331 is applicable to low-voltage power cables@ and control cables with a rated voltage. NOTE Although the scope is restricted to cables with rated voltage up to and including 0@6/1@0 kV@ the procedure may be used@ with the agreement of the manufacturer and the purchaser@ for cables with rated voltage up to and including 3@3 kV@ provided that suitable fuses are used.
信息：ICS：/ CCS：/ 发布：2009-05-01 实施：2018-03-30

IEC 60331-1:2018 着火条件下电缆的试验.电路完整性.第1部分:额定电压0.6/1.0千伏及以下总直径超过20毫米的电缆在至少830℃的温度下受冲击着火的试验方法
简介：
信息：ICS：13.220.40 CCS：发布：2018-03-28 实施：

SNI IEC 60331-2-2013
简介：
信息：ICS：11.040.50 CCS：发布：2013 实施：

IEC 60331-1-2009 Essais pour c?bles électriques soumis au feu – Intégrité des circuits – Partie 1: Méthode d’essai au feu avec chocs pour les c?bles de tension assignée au plus égale à 0@6/1@0 kV et de diamètre externe supérieur à 20 mm@ à une température d’au moins 830 d
简介：This part of IEC 60331 specifies the test apparatus to be used for testing cables required to maintain circuit integrity when subject to fire and mechanical shock where the test condition is based upon a flame with a controlled heat output corresponding to a temperature of a nominal 850 ?? It is intended for use when testing cables of greater than 20 mm overall diameter.It also provides@ in annex A@ the method of verification of the burner and control system used for the test.
信息：ICS：/ CCS：/ 发布：2009-05-01 实施：2018-03-30

IEC 60331-2:2018 RLV 着火条件下电缆的试验.电路完整性.第2部分:额定电压0.6/1.0 kV及以下总直径不超过20 mm的电缆在至少830°C温度下冲击着火的试验方法
简介：
信息：ICS：13.220.40 CCS：发布：2018-03-28 实施：

GOST IEC 60331-3-2013 着火条件下电缆的试验. 电路完整性. 第3部分. 在金属外壳中进行试验的额定电压小于等于0,6/1,0 kV的电缆在温度不低于830 ℃的冲击火焰下的试验方法
简介：
信息：ICS：13.220.40;29.060.20 CCS：发布：2013 实施：2015-07-01

IEC 60331-2-2009 Essais pour c?bles électriques soumis au feu – Intégrité des circuits – Partie 2: Méthode d’essai au feu avec chocs pour les c?bles de tension assignée au plus égale à 0@6/1@0 kV et de diamètre externe inférieur ou égal à 20 mm@ à une température d’au moi
简介：This part of IEC 60331 specifies the test apparatus to be used for testing cables required to maintain circuit integrity when subject to fire and mechanical shock where the test condition is based upon a flame with a controlled heat output corresponding to a temperature of a nominal 850 ?? It is intended for use when testing cables of greater than 20 mm overall diameter.It also provides@ in annex A@ the method of verification of the burner and control system used for the test.
信息：ICS：/ CCS：/ 发布：2009-05-01 实施：2018-03-30

IEC 60331-3:2018 着火条件下电缆的试验.电路完整性.第3部分:电缆在至少830℃温度下冲击着火的试验方法额定电压小于等于0.6/1.0 kV 在金属外壳中进行试验
简介：
信息：ICS：13.220.40 CCS：发布：2018-03-28 实施：

GOST IEC 60331-2-2013 着火条件下电缆的试验. 电路完整性. 第2部分. 额定电压小于等于0,6/1,0 kV且外径不超过20 mm的电缆在温度不低于830 ℃的冲击火焰下的试验方法"
简介：
信息：ICS：13.220.40;29.060.20 CCS：发布：2013 实施：2015-07-01

IEC 60331-2-2009 着火条件下电缆的试验.电路完整性.第2部分:额定电压高达和包括0.6/1.0 KV,全径不超过20 mm的电缆在温度不低于830°C的冲击火焰下的试验方法
简介：
信息：ICS：13.220.40;29.020;29.060.20 CCS：K13 发布：2009-05 实施：

IEC 60331-2-2018 着火条件下电缆的试验.电路完整性.第2部分:额定电压高达和包括0.6/1.0 KV,全径不超过20 mm的电缆在温度不低于830°C的冲击火焰下的试验方法
简介：This part of IEC 60331 specifies the test method for cables which are required to maintain circuit integrity when subject to fire and mechanical shock under specified conditions. This document is applicable to cables of rated voltage not exceeding 600 V/1000 V, including those of rated voltage below 80 V, metallic data and telecom cables and optical fibre cables. It is intended for use when testing cables of not greater than 20 mm overall diameter. Cables of larger diameter are intended to be tested using the apparatus, procedure and requirements of IEC 60331-1. This document includes details for the specific point of failure, continuity checking arrangement, test sample, test procedure and test report relevant to electric power and control cables with rated voltage up to and including 600 V/1000 V. Details for the specific point of failure, continuity checking arrangement, test sample, test procedure and test report relevant to metallic data and telecom cables and optical fibre cables are not given by IEC 60331-2. Although the scope is restricted to cables with rated voltage up to and including 0,6/1,0 kV, the procedure can be used, with the agreement of the manufacturer and the purchaser, for cables with rated voltage up to and including 1,8/3 (3,3) kV, provided that suitable fuses are used. Annex A provides the method of verification of the burner and control system used for the test. Requirements are stated for an identification that may optionally be marked on the cable to signify compliance with this standard. CAUTION - The test given in this standard may involve the use of dangerous voltages and temperatures. Suitable precautions should be taken against the risk of shock, burning, fire and explosion that may be involved, and against any noxious fumes that may be produced.
信息：ICS：13.220.40;29.020;29.060.20 CCS：K13 发布：2018-0301 实施：

GOST IEC 60331-1-2013 "着火条件下电缆的试验. 电路完整性. 第1部分. 额定电压小于等于0,6/1,0 kV且外径超过20 mm的电缆在温度不低于830 ℃的冲击火焰下的试验方法"
简介：
信息：ICS：13.220.40;29.060.20 CCS：发布：2013 实施：2015-07-01

IEC 60331-1-2009 电缆在着火条件下的试验.电路完整性.第1部分:额定电压高达(和包括)0.6/1.0 KV，全径大于20 mm的电缆在温度不低于830°C的冲击火焰下的试验方法
简介：
信息：ICS：13.220.40;29.020;29.060.20 CCS：K13 发布：2009-05 实施：

IEC 60331-1-2018 电缆在着火条件下的试验.电路完整性.第1部分:额定电压高达(和包括)0.6/1.0 KV，全径大于20 mm的电缆在温度不低于830°C的冲击火焰下的试验方法
简介：This part of IEC 60331 specifies the test method for cables which are required to maintain circuit integrity when subject to fire and mechanical shock under specified conditions. This document is applicable to cables of rated voltage not exceeding 600 V/1000 V, including those of rated voltage below 80 V, metallic data and telecom cables and optical fibre cables. It is intended for use when testing cables of greater than 20 mm overall diameter. Cables of smaller diameter are intended to be tested using the apparatus, procedure and requirements of IEC 60331-2. This document includes details for the specific point of failure, continuity checking arrangement, test sample, test procedure and test report relevant to electric power and control cables with rated voltage up to and including 600 V/1000 V. Details for the specific point of failure, continuity checking arrangement, test sample, test procedure and test report relevant to metallic data and telecom cables and optical fibre cables are not given by IEC 60331-1. Although the scope is restricted to cables with rated voltage up to and including 0,6/1,0 kV, the procedure can be used, with the agreement of the manufacturer and the purchaser, for cables with rated voltage up to and including 1,8/3 (3,3) kV, provided that suitable fuses are used. Annex A provides the method of verification of the burner and control system used for the test. Requirements are stated for an identification that may optionally be marked on the cable to signify compliance with this document. CAUTION - The test given in this standard may involve the use of dangerous voltages and temperatures. Suitable precautions should be taken against the risk of shock, burning, fire and explosion that may be involved, and against any noxious fumes that may be produced.
信息：ICS：13.220.40;29.020;29.060.20 CCS：K13 发布：2018-0301 实施：

GOST R IEC 60331-11-2012 着火条件下电缆和光缆的测试.线路完整性.第11部分:仪器.火焰温度达到750℃时的火况
简介：
信息：ICS：13.220.40;29.060.20 CCS：发布：2012-01-01 实施：2014-01-01

IEC 60331-3-2009 着火条件下电缆的试验.电路完整性.第3部分:额定电压高达(和包括)0.6/1.0 KV的电缆在金属外壳内、温度不低于830°C的冲击火焰下的试验方法
简介：
信息：ICS：13.220.40;29.020;29.060.20 CCS：K13 发布：2009-05 实施：

IEC 60331-1-2018
简介：This part of IEC 60331 specifies the test method for cables which are required to maintain circuit integrity when subject to fire and mechanical shock under specified conditions. This document is applicable to cables of rated voltage not exceeding 600 V/1 000 V@ including those of rated voltage below 80 V@ metallic data and telecom cables and optical fibre cables. It is intended for use when testing cables of greater than 20 mm overall diameter. Cables of smaller diameter are intended to be tested using the apparatus@ procedure and requirements of IEC 60331-2. This document includes details for the specific point of failure@ continuity checking arrangement@ test sample@ test procedure and test report relevant to electric power and control cables with rated voltage up to and including 600 V/1 000 V. Details for the specific point of failure@ continuity checking arrangement@ test sample@ test procedure and test report relevant to metallic data and telecom cables and optical fibre cables are not given by IEC 60331-1. Although the scope is restricted to cables with rated voltage up to and including 0@6/1@0 kV@ the procedure can be used@ with the agreement of the manufacturer and the purchaser@ for cables with rated voltage up to and including 1@8/3 (3@3) kV@ provided that suitable fuses are used. Annex A provides the method of verification of the burner and control system used for the test. Requirements are stated for an identification that may optionally be marked on the cable to signify compliance with this document. CAUTION ?C The test given in this standard may involve the use of dangerous voltages and temperatures. Suitable precautions should be taken against the risk of shock@ burning@ fire and explosion that may be involved@ and against any noxious fumes that may be produced.
信息：ICS：/ CCS：/ 发布：2018-03-01 实施：2018-03-30

GOST IEC 60331-21-2011 火焰条件下电缆与光缆测验.电路完整性.第21部分.规程和要求.电缆额定电压小于等于0.6/1.0 kV
简介：
信息：ICS：13.220.40;29.060.20 CCS：发布：2011 实施：2013-01-01

IEC 60331-1 (REDLINE + STANDARD)-2018
简介：This part of IEC 60331 specifies the test method for cables which are required to maintain circuit integrity when subject to fire and mechanical shock under specified conditions. This document is applicable to cables of rated voltage not exceeding 600 V/1 000 V@ including those of rated voltage below 80 V@ metallic data and telecom cables and optical fibre cables. It is intended for use when testing cables of greater than 20 mm overall diameter. Cables of smaller diameter are intended to be tested using the apparatus@ procedure and requirements of IEC 60331-2. This document includes details for the specific point of failure@ continuity checking arrangement@ test sample@ test procedure and test report relevant to electric power and control cables with rated voltage up to and including 600 V/1 000 V. Details for the specific point of failure@ continuity checking arrangement@ test sample@ test procedure and test report relevant to metallic data and telecom cables and optical fibre cables are not given by IEC 60331-1. Although the scope is restricted to cables with rated voltage up to and including 0@6/1@0 kV@ the procedure can be used@ with the agreement of the manufacturer and the purchaser@ for cables with rated voltage up to and including 1@8/3 (3@3) kV@ provided that suitable fuses are used. Annex A provides the method of verification of the burner and control system used for the test. Requirements are stated for an identification that may optionally be marked on the cable to signify compliance with this document. CAUTION ?C The test given in this standard may involve the use of dangerous voltages and temperatures. Suitable precautions should be taken against the risk of shock@ burning@ fire and explosion that may be involved@ and against any noxious fumes that may be produced.
信息：ICS：/ CCS：/ 发布：2018-03-01 实施：2018-03-30

GOST IEC 60331-31-2011 火焰条件下电缆与光缆测验.电路完整性.第31部分.火焰带冲击条件下试验的规程和要求.电缆额定电压小于等于0.6/1.0 kV
简介：
信息：ICS：13.220.40;29.060.20 CCS：发布：2011 实施：2013-01-01

IEC 60331-3 (REDLINE + STANDARD)-2018
简介：
信息：ICS：/ CCS：/ 发布：2018-03-01 实施：2018-03-30

GOST IEC 60331-25-2011 火焰条件下电缆与光缆测验.电路完整性.第25部分.试验的进行及对其要求.光缆
简介：
信息：ICS：13.220.40;33.180.10 CCS：发布：2011 实施：2013-01-01

IEC 60331-3-2018
简介：This part of IEC 60331 specifies the test method for cables which are required to maintain circuit integrity when tested in a metal enclosure and when subject to fire and mechanical shock under specified conditions. This document is applicable to cables of rated voltage not exceeding 600 V/1 000 V@ including those of rated voltage below 80 V@ metallic data and telecom cables and optical fibre cables. It is intended for use when testing cables not greater than 20 mm overall diameter. This document includes details for the specific point of failure@ continuity checking arrangement@ test sample@ test procedure and test report relevant to electric power and control cables with rated voltage up to and including 600 V/1 000 V. Details for the specific point of failure@ continuity checking arrangement@ test sample@ test procedure and test report relevant to metallic data and telecom cables and optical fibre cables are not given by IEC 60331-3. Although the scope is restricted to cables with rated voltage up to and including 0@6/1@0 kV@ the procedure can be used@ with the agreement of the manufacturer and the purchaser@ for cables with rated voltage up to and including 1@8/3 (3@3) kV@ provided that suitable fuses are used. It is not assumed that cables successfully assessed by this method@ will also pass requirements for either IEC 60331-1 or IEC 60331-2. Testing to either of these two standards is to be carried out separately. Such additional performance can be recognised by the marking in accordance with IEC 60331-1:2018 Clause 11 or IEC 60331-2:2018 Clause 11. Annex A provides the method of verification of the burner and control system used for the test. CAUTION ?C The test given in this standard may involve the use of dangerous voltages and temperatures. Suitable precautions should be taken against the risk of shock@ burning@ fire and explosion that may be involved@ and against any noxious fumes that may be produced.
信息：ICS：/ CCS：/ 发布：2018-03-01 实施：2018-03-30

GOST IEC 60331-12-2011 火焰条件下电缆测验.电路完整性.第12部分.装置.至少830℃温度下火焰带冲击
简介：
信息：ICS：13.220.40;29.060.20 CCS：发布：2011 实施：2013-01-01

IEC 60331-11 AMD 1-2009 电缆在着火条件下的试验.电路完整性.第11部分:仪器.火焰温度等于高于750°C时的孤立火焰.修改件1
简介：
信息：ICS：13.220.40;29.020;29.060.20 CCS：K13 发布：2009-05 实施：