A568/A568M检测标准

A568/A568M相关标准参考信息

ASTM A568/A568M-19a 热轧和冷轧低合金结构和高强度碳素钢薄板的一般要求
简介：
信息：ICS：77.140.50 CCS： 发布：2019-11-01 实施：

ASTM A568/A568M-2011 结构和高强度低合金热轧和冷轧碳钢薄板材的一般要求用标准规格
简介：1.1 This specification covers the general requirements for steel sheet in coils and cut lengths. It applies to the following specifications that describe carbon steel, structural steel, and high-strength, low-alloy steel (HSLA) furnished as hot-rolled sheet and cold-rolled sheet: Specifications A414/A414M, A424, A606, A659/A659M, A794, A1008/A1008M, A1011/A1011M, and A1039/A1039M. 1.2 This specification is not applicable to hot-rolled heavy-thickness carbon sheet coils (Specification A635/A635M). 1.3 In case of any conflict in requirements, the requirements of the individual material specification shall prevail over those of this general specification. 1.4 For the purposes of determining conformance with this and the appropriate product specification referenced in 1.1, values shall be rounded to the nearest unit in the right hand place of figures used in expressing the limiting values in accordance with the rounding method of Practice E29. 1.5 Annex A1 lists permissible variations in dimensions and mass (see Note 1) in SI [metric] units. The values listed are not exact conversions of the values listed in the inch-pound tables, but instead are rounded or rationalized values. Conformance to Annex A1 is mandatory when the x201C;Mx201D; specification is used. Note 18212;The term weight is used when inch-pound units are the standard. However, under SI the preferred term is mass. 1.6 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.7 This specification and the applicable material specifications are expressed in both inch-pound units and SI units. However, unless the order specifies the applicable x201C;Mx201D; specification designation (SI units), the material shall be furnished to inch-pound units.
信息：ICS：77.140.50 CCS：H46 发布：2011 实施：

ASTM A568/A568M-2004a
简介：1.1 This specification covers the general requirements for steel sheet in coils and cut lengths. It applies to the following specifications that describe carbon steel, structural steel, and high-strength, low-alloy steel (HSLA) furnished as hot-rolled sheet and cold-rolled sheet: Specifications A 414/A 414M, A 424, A 606, A 659/A 659M, A 794, A 1008/A 1008M, and A 1011/A 1011M. 1.2 This specification is not applicable to hot-rolled heavy-thickness carbon sheet coils (Specification A 635/A 635M).1.3 In case of any conflict in requirements, the requirements of the individual material specification shall prevail over those of this general specification. 1.4 For the purposes of determining conformance with this and the appropriate product specification referenced in , values shall be rounded to the nearest unit in the right hand place of figures used in expressing the limiting values in accordance with the rounding method of Practice E 29.1.5 lists permissible variations in dimensions and mass (see Note 0) in SI [metric] units. The values listed are not exact conversions of the values listed in the inch-pound tables, but instead are rounded or rationalized values. Conformance to is mandatory when the "M" specification is used. The term weight is used when inch-pound units are the standard. However, under SI the preferred term is mass. 1.6 The values stated in either inch-pound units or SI units are to be regarded as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.1.7 This specification and the applicable material specifications are expressed in both inch-pound units and SI units. However, unless the order specifies the applicable "M" specification designation (SI units), the material shall be furnished to inch-pound units.
信息：ICS：77.140.50 (Flat steel products and semi-products) CCS： 发布：2004 实施：

ASTM A568/A568M-19 热轧和冷轧低合金结构和高强度碳素钢薄板的一般要求
简介：
信息：ICS：77.140.50 CCS： 发布：2019-09-01 实施：

ASTM A568/A568M-2011a 结构和高强度低合金热轧和冷轧碳钢薄板材的一般要求用标准规格
简介：1.1 This specification covers the general requirements for steel sheet in coils and cut lengths. It applies to the following specifications that describe carbon steel, structural steel, and high-strength, low-alloy steel (HSLA) furnished as hot-rolled sheet and cold-rolled sheet: Specifications A414/A414M, A424, A606, A659/A659M, A794, A1008/A1008M, A1011/A1011M, and A1039/A1039M. 1.2 This specification is not applicable to hot-rolled heavy-thickness carbon sheet coils (Specification A635/A635M). 1.3 In case of any conflict in requirements, the requirements of the individual material specification shall prevail over those of this general specification. 1.4 For the purposes of determining conformance with this and the appropriate product specification referenced in 1.1, values shall be rounded to the nearest unit in the right hand place of figures used in expressing the limiting values in accordance with the rounding method of Practice E29. 1.5 Annex A1 lists permissible variations in dimensions and mass (see Note 1) in SI [metric] units. The values listed are not exact conversions of the values listed in the inch-pound tables, but instead are rounded or rationalized values. Conformance to Annex A1 is mandatory when the x201C;Mx201D; specification is used. Note 18212;The term weight is used when inch-pound units are the standard. However, under SI the preferred term is mass. 1.6 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.7 This specification and the applicable material specifications are expressed in both inch-pound units and SI units. However, unless the order specifies the applicable x201C;Mx201D; specification designation (SI units), the material shall be furnished to inch-pound units.
信息：ICS：77.140.50 (Flat steel products and semi-products) CCS：H46 发布：2011 实施：

ASME SEC II A SA-568/SA-568M-2003 热轧和冷轧低合金碳素和高强度板钢通用要求规范.ASTM A 568/A 568M-02
简介：Boiler and Pressure Vessel,Specification for Steel, Sheet, Carbon and High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, General Requirements For ASTM A 568/A 568M-02
信息：ICS： CCS：H46 发布：2003-07-01 实施：

ASTM A568/A568M-17a 热轧和冷轧低合金结构和高强度碳素钢薄板的一般要求
简介：
信息：ICS：77.140.50 CCS： 发布：2017-11-01 实施：

ASTM A568/A568M-2011b 高强度低合金热轧及冷轧结构性碳素钢板材和带材的标准规格.一般要求
简介：1.1 This specification covers the general requirements for steel sheet in coils and cut lengths. It applies to the following specifications that describe carbon steel, structural steel, and high-strength, low-alloy steel (HSLA) furnished as hot-rolled sheet and cold-rolled sheet: Specifications A414/A414M, A424, A606, A659/A659M, A794, A1008/A1008M, A1011/A1011M, and A1039/A1039M. 1.2 This specification is not applicable to hot-rolled heavy-thickness carbon sheet coils (Specification A635/A635M). 1.3 In case of any conflict in requirements, the requirements of the individual material specification shall prevail over those of this general specification. 1.4 For the purposes of determining conformance with this and the appropriate product specification referenced in 1.1, values shall be rounded to the nearest unit in the right hand place of figures used in expressing the limiting values in accordance with the rounding method of Practice E29. 1.5 Annex A1 lists permissible variations in dimensions and mass (see Note 1) in SI [metric] units. The values listed are not exact conversions of the values listed in the inch-pound tables, but instead are rounded or rationalized values. Conformance to Annex A1 is mandatory when the x201C;Mx201D; specification is used. Note 18212;The term weight is used when inch-pound units are the standard. However, under SI the preferred term is mass. 1.6 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.7 This specification and the applicable material specifications are expressed in both inch-pound units and SI units. However, unless the order specifies the applicable x201C;Mx201D; specification designation (SI units), the material shall be furnished to inch-pound units.
信息：ICS：77.140.50 (Flat steel products and semi-products) CCS：H46 发布：2011 实施：

ASTM A568/A568M-03 热轧和冷轧碳素钢薄板和低合金高强度钢的一般要求
简介：
信息：ICS：77.140.50 CCS： 发布：2003-03-10 实施：

ASTM A568/A568M-17 热轧和冷轧低合金结构和高强度碳素钢薄板的一般要求
简介：
信息：ICS：77.140.50 CCS： 发布：2017-09-01 实施：

ASTM A568/A568M-09a 热轧和冷轧低合金结构和高强度碳素钢薄板的一般要求
简介：
信息：ICS：77.140.50 CCS： 发布：2009-11-01 实施：

ASTM A568/A568M-2003
简介：1.1 This specification covers the general requirements for steel sheet in coils and cut lengths. It applies to the following specifications that describe carbon steel and high-strength, low-alloy steel (HSLA) furnished as hot-rolled sheet and cold-rolled sheet: Specifications A 414/A 414M, A 424, A 606, A 659/A 659M, A 794, A 1008/A 1008M, and A 1011/A 1011M. 1.2 This specification is not applicable to hot-rolled heavy-thickness carbon sheet coils (ASTM Specification A 635/A 635M). 1.3 In case of any conflict in requirements, the requirements of the individual material specification shall prevail over those of this general specification. 1.4 For the purposes of determining conformance with this and the appropriate product specification referenced in , values shall be rounded to the nearest unit in the right hand place of figures used in expressing the limiting values in accordance with the rounding method of Practice E 29.1.5 lists permissible variations in dimensions and mass (see Note 1) in SI [metric] units. The values listed are not exact conversions of the values listed in the inch-pound tables, but instead are rounded or rationalized values. Conformance to is mandatory when the "M" specification is used. Note 18212;The term weight is used when inch-pound units are the standard. However, under SI the preferred term is mass. 1.6 The values stated in either inch-pound units or SI units are to be regarded as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.1.7 This specification and the applicable material specifications are expressed in both inch-pound units and SI units. However, unless the order specifies the applicable "M" specification designation (SI units), the material shall be furnished to inch-pound units.
信息：ICS：77.140.50 (Flat steel products and semi-products) CCS： 发布：2003 实施：

ASTM A568/A568M-2017 通用热轧和冷轧高强度低合金结构碳素钢薄板的标准规格
简介：1.1x00a0;This specification covers the general requirements for steel sheet in coils and cut lengths. It applies to the following specifications that describe carbon steel, structural steel, and high-strength, low-alloy steel (HSLA) furnished as hot-rolled sheet and cold-rolled sheet: Specifications A414/A414M, A424, A606, A659/A659M, A794, A1008/A1008M, A1011/A1011M, and A1039/A1039M. 1.2x00a0;This specification is not applicable to hot-rolled heavy-thickness carbon sheet coils (Specification A635/A635M). 1.3x00a0;In case of any conflict in requirements, the requirements of the individual material specification shall prevail over those of this general specification. 1.4x00a0;For the purposes of determining conformance with this and the appropriate product specification referenced in 1.1, values shall be rounded to the nearest unit in the right hand place of figures used in expressing the limiting values in accordance with the rounding method of Practice E29. 1.5x00a0;Annex A1 lists permissible variations in dimensions and mass (see Note 1) in SI [metric] units. The values listed are not exact conversions of the values listed in the inch-pound tables, but instead are rounded or rationalized values. Conformance to Annex A1 is mandatory when the x201c;Mx201d; specification is used. Note 1:x00a0;The term weight is used when inch-pound units are the standard. However, under SI the preferred term is mass. 1.6x00a0;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.7x00a0;This specification and the applicable material specifications are expressed in both inch-pound units and SI units. However, unless the order specifies the applicable x201c;Mx201d; specification designation (SI units), the material shall be furnished to inch-pound units. 1.8x00a0;This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade
信息：ICS：77.140.50 CCS：H46 发布：2017 实施：

ASTM A568/A568M-09 热轧和冷轧低合金结构和高强度碳素钢薄板的一般要求
简介：
信息：ICS：77.140.50 CCS： 发布：2009-05-01 实施：

ASTM A568/A568M-00b 热轧和冷轧碳素钢薄板和低合金高强度钢的一般要求
简介：
信息：ICS：77.140.50 CCS： 发布：2002-03-10 实施：

ASTM A568/A568M-2017a 热轧和冷轧的结构型和高强度低合金碳钢薄板材的标准规格, 通用要求
简介：1.1x00a0;This specification covers the general requirements for steel sheet in coils and cut lengths. It applies to the following specifications that describe carbon steel, structural steel, and high-strength, low-alloy steel (HSLA) furnished as hot-rolled sheet and cold-rolled sheet: Specifications A414/A414M, A424, A606, A659/A659M, A794, A1008/A1008M, A1011/A1011M, and A1039/A1039M. 1.2x00a0;This specification is not applicable to hot-rolled heavy-thickness carbon sheet coils (Specification A635/A635M). 1.3x00a0;In case of any conflict in requirements, the requirements of the individual material specification shall prevail over those of this general specification. 1.4x00a0;For the purposes of determining conformance with this and the appropriate product specification referenced in 1.1, values shall be rounded to the nearest unit in the right hand place of figures used in expressing the limiting values in accordance with the rounding method of Practice E29. 1.5x00a0;Annex A1 lists permissible variations in dimensions and mass (see Note 1) in SI [metric] units. The values listed are not exact conversions of the values listed in the inch-pound tables, but instead are rounded or rationalized values. Conformance to Annex A1 is mandatory when the x201c;Mx201d; specification is used. Note 1:x00a0;The term weight is used when inch-pound units are the standard. However, under SI the preferred term is mass. 1.6x00a0;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.7x00a0;This specification and the applicable material specifications are expressed in both inch-pound units and SI units. However, unless the order specifies the applicable x201c;Mx201d; specification designation (SI units), the material shall be furnished to inch-pound units. 1.8x00a0;This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade
信息：ICS：77.140.50 CCS：H46 发布：2017 实施：

ASTM A568/A568M-2009
简介：1.1 This specification covers the general requirements for steel sheet in coils and cut lengths. It applies to the following specifications that describe carbon steel, structural steel, and high-strength, low-alloy steel (HSLA) furnished as hot-rolled sheet and cold-rolled sheet: Specifications A 414/A 414M, A 424, A 606, A 659/A 659M, A 794, A 1008/A 1008M, A 1011/A 1011M, and A 1039/A 1039M. 1.2 This specification is not applicable to hot-rolled heavy-thickness carbon sheet coils (Specification A 635/A 635M). 1.3 In case of any conflict in requirements, the requirements of the individual material specification shall prevail over those of this general specification. 1.4 For the purposes of determining conformance with this and the appropriate product specification referenced in 1.1, values shall be rounded to the nearest unit in the right hand place of figures used in expressing the limiting values in accordance with the rounding method of Practice E 29. 1.5 Annex A1 lists permissible variations in dimensions and mass (see Note 1) in SI [metric] units. The values listed are not exact conversions of the values listed in the inch-pound tables, but instead are rounded or rationalized values. Conformance to Annex A1 is mandatory when the x201C;Mx201D; specification is used. Note 18212;The term weight is used when inch-pound units are the standard. However, under SI the preferred term is mass. 1.6 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.7 This specification and the applicable material specifications are expressed in both inch-pound units and SI units. However, unless the order specifies the applicable x201C;Mx201D; specification designation (SI units), the material shall be furnished to inch-pound units.
信息：ICS：77.140.50 (Flat steel products and semi-products) CCS： 发布：2009 实施：

ASTM A568/A568M-02 热轧和冷轧碳素钢薄板和低合金高强度钢的一般要求
简介：
信息：ICS：77.140.50 CCS： 发布：2002-03-10 实施：

ASTM A568/A568M-15 热轧和冷轧低合金结构和高强度碳素钢薄板的一般要求
简介：
信息：ICS：77.140.50 CCS： 发布：2015-11-01 实施：

ASTM A568/A568M-2009a 结构和高强度低合金热轧和冷轧碳钢薄板材的一般要求用标准规范
简介：1.1 This specification covers the general requirements for steel sheet in coils and cut lengths. It applies to the following specifications that describe carbon steel, structural steel, and high-strength, low-alloy steel (HSLA) furnished as hot-rolled sheet and cold-rolled sheet: Specifications A414/A414M, A424, A606, A659/A659M, A794, A1008/A1008M, A1011/A1011M, and A1039/A1039M. 1.2 This specification is not applicable to hot-rolled heavy-thickness carbon sheet coils (Specification A635/A635M). 1.3 In case of any conflict in requirements, the requirements of the individual material specification shall prevail over those of this general specification. 1.4 For the purposes of determining conformance with this and the appropriate product specification referenced in 1.1, values shall be rounded to the nearest unit in the right hand place of figures used in expressing the limiting values in accordance with the rounding method of Practice E29. 1.5 Annex A1 lists permissible variations in dimensions and mass (see Note 1) in SI [metric] units. The values listed are not exact conversions of the values listed in the inch-pound tables, but instead are rounded or rationalized values. Conformance to Annex A1 is mandatory when the x201C;Mx201D; specification is used. Note 18212;The term weight is used when inch-pound units are the standard. However, under SI the preferred term is mass. 1.6 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.7 This specification and the applicable material specifications are expressed in both inch-pound units and SI units. However, unless the order specifies the applicable x201C;Mx201D; specification designation (SI units), the material shall be furnished to inch-pound units.
信息：ICS：77.140.50 (Flat steel products and semi-products) CCS：H46 发布：2009 实施：

ASTM A568/A568M-01 热轧和冷轧碳素钢薄板和低合金高强度钢的一般要求
简介：
信息：ICS：77.140.50 CCS： 发布：2002-03-10 实施：

ASTM A568/A568M-2015 热轧和冷轧的结构型和高强度低合金碳钢薄板材的标准规格, 通用要求
简介：1.1x00a0;This specification covers the general requirements for steel sheet in coils and cut lengths. It applies to the following specifications that describe carbon steel, structural steel, and high-strength, low-alloy steel (HSLA) furnished as hot-rolled sheet and cold-rolled sheet: Specifications A414/A414M, A424, A606, A659/A659M, A794, A1008/A1008M, A1011/A1011M, and A1039/A1039M. 1.2x00a0;This specification is not applicable to hot-rolled heavy-thickness carbon sheet coils (Specification A635/A635M). 1.3x00a0;In case of any conflict in requirements, the requirements of the individual material specification shall prevail over those of this general specification. 1.4x00a0;For the purposes of determining conformance with this and the appropriate product specification referenced in 1.1, values shall be rounded to the nearest unit in the right hand place of figures used in expressing the limiting values in accordance with the rounding method of Practice E29. 1.5x00a0;Annex A1 lists permissible variations in dimensions and mass (see Note 1) in SI [metric] units. The values listed are not exact conversions of the values listed in the inch-pound tables, but instead are rounded or rationalized values. Conformance to Annex A1 is mandatory when the x201c;Mx201d; specification is used. Note 1:x00a0;The term weight is used when inch-pound units are the standard. However, under SI the preferred term is mass. 1.6x00a0;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.7x00a0;This specification and the applicable material specifications are expressed in both inch-pound units and SI units. However, unless the order specifies the applicable x201c;Mx201d; specification designation (SI units), the material shall be furnished to inch-pound units.
信息：ICS：77.140.50 CCS： 发布：2015 实施：

ASTM A568/A568M-2009ae1
简介：1.1 This specification covers the general requirements for steel sheet in coils and cut lengths. It applies to the following specifications that describe carbon steel, structural steel, and high-strength, low-alloy steel (HSLA) furnished as hot-rolled sheet and cold-rolled sheet: Specifications A414/A414M, A424, A606, A659/A659M, A794, A1008/A1008M, A1011/A1011M, and A1039/A1039M. 1.2 This specification is not applicable to hot-rolled heavy-thickness carbon sheet coils (Specification A635/A635M). 1.3 In case of any conflict in requirements, the requirements of the individual material specification shall prevail over those of this general specification. 1.4 For the purposes of determining conformance with this and the appropriate product specification referenced in 1.1, values shall be rounded to the nearest unit in the right hand place of figures used in expressing the limiting values in accordance with the rounding method of Practice E29. 1.5 Annex A1 lists permissible variations in dimensions and mass (see Note 1) in SI [metric] units. The values listed are not exact conversions of the values listed in the inch-pound tables, but instead are rounded or rationalized values. Conformance to Annex A1 is mandatory when the x201C;Mx201D; specification is used. Note 18212;The term weight is used when inch-pound units are the standard. However, under SI the preferred term is mass. 1.6 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.7 This specification and the applicable material specifications are expressed in both inch-pound units and SI units. However, unless the order specifies the applicable x201C;Mx201D; specification designation (SI units), the material shall be furnished to inch-pound units.
信息：ICS：77.140.50 CCS： 发布：2009 实施：

ASTM A568/A568M-2002
简介：1.1 This specification covers the general requirements for steel sheet in coils and cut lengths. It applies to the following specifications that describe carbon steel and high-strength, low-alloy steel (HSLA) furnished as hot-rolled sheet and cold-rolled sheet: Specifications A 414/A 414M, A 424, A 606, A 659/A 659M, A 794, A 1008/A 1008M, and A 1011/A 1011M. 1.2 This specification is not applicable to hot-rolled heavy-thickness carbon sheet coils (ASTM Specification A 635/A 635M). 1.3 In case of any conflict in requirements, the requirements of the individual material specification shall prevail over those of this general specification. 1.4 For the purposes of determining conformance with this and the appropriate product specification referenced in , values shall be rounded to the nearest unit in the right hand place of figures used in expressing the limiting values in accordance with the rounding method of Practice E 29.1.5 lists permissible variations in dimensions and mass (see Note 1) in SI [metric] units. The values listed are not exact conversions of the values listed in the inch-pound tables, but instead are rounded or rationalized values. Conformance to is mandatory when the "M" specification is used. Note 18212;The term weight is used when inch-pound units are the standard. However, under SI the preferred term is mass. 1.6 The values stated in either inch-pound units or SI units are to be regarded as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.1.7 This specification and the applicable material specifications are expressed in both inch-pound units and SI units. However, unless the order specifies the applicable "M" specification designation (SI units), the material shall be furnished to inch-pound units.
信息：ICS：77.140.50 (Flat steel products and semi-products) CCS： 发布：2002 实施：

ASTM A568/A568M-14 热轧和冷轧低合金结构和高强度碳素钢薄板的一般要求
简介：
信息：ICS：77.140.50 CCS： 发布：2014-10-01 实施：

ASTM A568/A568M-07a 热轧和冷轧低合金结构和高强度碳素钢薄板的一般要求
简介：
信息：ICS：77.140.50 CCS： 发布：2007-11-01 实施：

ASTM A568/A568M-2001
简介：1.1 This specification covers the general requirements for steel sheet in coils and cut lengths. It applies to the following specifications that describe carbon steel and high-strength, low-alloy steel (HSLA) furnished as hot-rolled sheet and cold-rolled sheet: Specifications A 414/A 414M, A 424, A 606, A 659/A 659M, A 794, A 1008/A 1008M, and A 1011/A 1011M. 1.2 This specification is not applicable to hot-rolled heavy-thickness carbon sheet coils (ASTM Specification A 635/A 635M). 1.3 In case of any conflict in requirements, the requirements of the individual material specification shall prevail over those of this general specification. 1.4 For the purposes of determining conformance with this and the appropriate product specification referenced in , values shall be rounded to the nearest unit in the right hand place of figures used in expressing the limiting values in accordance with the rounding method of Practice E 29.1.5 lists permissible variations in dimensions and mass (see Note 1) in SI [metric] units. The values listed are not exact conversions of the values listed in the inch-pound tables, but instead are rounded or rationalized values. Conformance to is mandatory when the "M" specification is used. Note 18212;The term weight is used when inch-pound units are the standard. However, under SI the preferred term is mass. 1.6 The values stated in either inch-pound units or SI units are to be regarded as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.1.7 This specification and the applicable material specifications are expressed in both inch-pound units and SI units. However, unless the order specifies the applicable "M" specification designation (SI units), the material shall be furnished to inch-pound units.
信息：ICS：77.140.50 (Flat steel products and semi-products) CCS： 发布：2001 实施：

ASTM A568/A568M-2014 热轧和冷轧的结构型和高强度低合金碳钢薄板材的标准规格, 通用要求
简介：1.1x00a0;This specification covers the general requirements for steel sheet in coils and cut lengths. It applies to the following specifications that describe carbon steel, structural steel, and high-strength, low-alloy steel (HSLA) furnished as hot-rolled sheet and cold-rolled sheet: Specifications A414/A414M, A424, A606, A659/A659M, A794, A1008/A1008M, A1011/A1011M, and A1039/A1039M. 1.2x00a0;This specification is not applicable to hot-rolled heavy-thickness carbon sheet coils (Specification A635/A635M). 1.3x00a0;In case of any conflict in requirements, the requirements of the individual material specification shall prevail over those of this general specification. 1.4x00a0;For the purposes of determining conformance with this and the appropriate product specification referenced in 1.1, values shall be rounded to the nearest unit in the right hand place of figures used in expressing the limiting values in accordance with the rounding method of Practice E29. 1.5x00a0;Annex A1 lists permissible variations in dimensions and mass (see Note 1) in SI [metric] units. The values listed are not exact conversions of the values listed in the inch-pound tables, but instead are rounded or rationalized values. Conformance to Annex A1 is mandatory when the x201c;Mx201d; specification is used. Note 1:x00a0;The term weight is used when inch-pound units are the standard. However, under SI the preferred term is mass. 1.6x00a0;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.7x00a0;This specification and the applicable material specifications are expressed in both inch-pound units and SI units. However, unless the order specifies the applicable x201c;Mx201d; specification designation (SI units), the material shall be furnished to inch-pound units.
信息：ICS：77.140.50 CCS：H46 发布：2014 实施：

ASTM A568/A568M-07 热轧和冷轧低合金结构和高强度碳素钢薄板的一般要求
简介：
信息：ICS：77.140.50 CCS： 发布：2007-09-01 实施：

ASTM A568/A568M-2000b
简介：1.1 This specification covers the general requirements for steel sheet in coils and cut lengths. It applies to the following specifications that describe carbon steel and high-strength, low-alloy steel (HSLA) furnished as hot-rolled sheet and cold-rolled sheet: Specifications A 414/A 414M, A 424, A 606, A 659/A 659M, A 794, A 1008/A 1008M, and A 1011/A 1011M. 1.2 This specification is not applicable to hot-rolled heavy-thickness carbon sheet coils (ASTM Specification A 635/A 635M). 1.3 In case of any conflict in requirements, the requirements of the individual material specification shall prevail over those of this general specification. 1.4 For the purposes of determining conformance with this and the appropriate product specification referenced in , values shall be rounded to the nearest unit in the right hand place of figures used in expressing the limiting values in accordance with the rounding method of Practice E 29.1.5 lists permissible variations in dimensions and mass (see Note 1) in SI [metric] units. The values listed are not exact conversions of the values listed in the inch-pound tables, but instead are rounded or rationalized values. Conformance to is mandatory when the "M" specification is used. Note 18212;The term weight is used when inch-pound units are the standard. However, under SI the preferred term is mass. 1.6 The values stated in either inch-pound units or SI units are to be regarded as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.1.7 This specification and the applicable material specifications are expressed in both inch-pound units and SI units. However, unless the order specifies the applicable "M" specification designation (SI units), the material shall be furnished to inch-pound units.
信息：ICS：77.140.50 (Flat steel products and semi-products) CCS： 发布：2000 实施：

ASTM A568/A568M-13ae1 热轧和冷轧低合金结构和高强度碳素钢薄板的一般要求
简介：
信息：ICS：77.140.50 CCS： 发布：2013-10-01 实施：

ASTM A568/A568M-2007a
简介：1.1 This specification covers the general requirements for steel sheet in coils and cut lengths. It applies to the following specifications that describe carbon steel, structural steel, and high-strength, low-alloy steel (HSLA) furnished as hot-rolled sheet and cold-rolled sheet: Specifications A 414/A 414M, A 424, A 606, A 659/A 659M, A 794, A 1008/A 1008M, A 1011/A 1011M, and A 1039/A 1039M. 1.2 This specification is not applicable to hot-rolled heavy-thickness carbon sheet coils (Specification A 635/A 635M). 1.3 In case of any conflict in requirements, the requirements of the individual material specification shall prevail over those of this general specification. 1.4 For the purposes of determining conformance with this and the appropriate product specification referenced in 1.1, values shall be rounded to the nearest unit in the right hand place of figures used in expressing the limiting values in accordance with the rounding method of Practice E 29. 1.5 Annex A1 lists permissible variations in dimensions and mass (see Note 1) in SI [metric] units. The values listed are not exact conversions of the values listed in the inch-pound tables, but instead are rounded or rationalized values. Conformance to Annex A1 is mandatory when the x201C;Mx201D; specification is used. Note 18212;The term weight is used when inch-pound units are the standard. However, under SI the preferred term is mass. 1.6 The values stated in either inch-pound units or SI units are to be regarded as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. 1.7 This specification and the applicable material specifications are expressed in both inch-pound units and SI units. However, unless the order specifies the applicable x201C;Mx201D; specification designation (SI units), the material shall be furnished to inch-pound units.
信息：ICS：77.140.50 (Flat steel products and semi-products) CCS： 发布：2007 实施：

简介： 信息：

ASTM A568/A568M-13a 热轧和冷轧低合金结构和高强度碳素钢薄板的一般要求
简介：
信息：ICS：77.140.50 CCS： 发布：2013-10-01 实施：

ASTM A568/A568M-2007
简介：1.1 This specification covers the general requirements for steel sheet in coils and cut lengths. It applies to the following specifications that describe carbon steel, structural steel, and high-strength, low-alloy steel (HSLA) furnished as hot-rolled sheet and cold-rolled sheet: Specifications A 414/A 414M, A 424, A 606, A 659/A 659M, A 794, A 1008/A 1008M, A 1011/A 1011M, and A 1039/A 1039M. 1.2 This specification is not applicable to hot-rolled heavy-thickness carbon sheet coils (Specification A 635/A 635M). 1.3 In case of any conflict in requirements, the requirements of the individual material specification shall prevail over those of this general specification. 1.4 For the purposes of determining conformance with this and the appropriate product specification referenced in , values shall be rounded to the nearest unit in the right hand place of figures used in expressing the limiting values in accordance with the rounding method of Practice E 29.1.5 lists permissible variations in dimensions and mass (see Note 1) in SI [metric] units. The values listed are not exact conversions of the values listed in the inch-pound tables, but instead are rounded or rationalized values. Conformance to is mandatory when the "M" specification is used. Note 1 - The term weight is used when inch-pound units are the standard. However, under SI the preferred term is mass. 1.6 The values stated in either inch-pound units or SI units are to be regarded as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.1.7 This specification and the applicable material specifications are expressed in both inch-pound units and SI units. However, unless the order specifies the applicable "M" specification designation (SI units), the material shall be furnished to inch-pound units.
信息：ICS： CCS： 发布：2007 实施：

简介： 信息：

ASTM A568/A568M-13 热轧和冷轧低合金结构和高强度碳素钢薄板的一般要求
简介：
信息：ICS：77.140.50 CCS： 发布：2013-05-01 实施：

ASTM A568/A568M-06a 热轧和冷轧低合金结构和高强度碳素钢薄板的一般要求
简介：
信息：ICS：77.140.50 CCS： 发布：2006-05-15 实施：

简介： 信息：

ASTM A568/A568M-2013a 高强度低合金热轧及冷轧结构性碳素钢板材和片材的标准规格.通用要求
简介：1.1x00a0;This specification covers the general requirements for steel sheet in coils and cut lengths. It applies to the following specifications that describe carbon steel, structural steel, and high-strength, low-alloy steel (HSLA) furnished as hot-rolled sheet and cold-rolled sheet: Specifications A414/A414M, A424, A606, A659/A659M, A794, A1008/A1008M, A1011/A1011M, and A1039/A1039M. 1.2x00a0;This specification is not applicable to hot-rolled heavy-thickness carbon sheet coils (Specification A635/A635M). 1.3x00a0;In case of any conflict in requirements, the requirements of the individual material specification shall prevail over those of this general specification. 1.4x00a0;For the purposes of determining conformance with this and the appropriate product specification referenced in 1.1, values shall be rounded to the nearest unit in the right hand place of figures used in expressing the limiting values in accordance with the rounding method of Practice E29. 1.5x00a0;Annex A1 lists permissible variations in dimensions and mass (see Note 1) in SI [metric] units. The values listed are not exact conversions of the values listed in the inch-pound tables, but instead are rounded or rationalized values. Conformance to Annex A1 is mandatory when the x201c;Mx201d; specification is used. Note 1x2014;The term weight is used when inch-pound units are the standard. However, under SI the preferred term is mass. 1.6x00a0;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.7x00a0;This specification and the applicable material specifications are expressed in both inch-pound units and SI units. However, unless the order specifies the applicable x201c;Mx201d; specification designation (SI units), the material shall be furnished to inch-pound units.
信息：ICS：77.140.50 (Flat steel products and semi-products) CCS：H46 发布：2013 实施：

ASTM A568/A568M-06 热轧和冷轧低合金结构和高强度碳素钢薄板的一般要求
简介：
信息：ICS：77.140.50 CCS： 发布：2006-03-01 实施：

简介： 信息：

ASTM A568/A568M-2013 高强度低合金热轧及冷轧结构性碳素钢板材和带材的标准规格.通用要求
简介：1.1x00a0;This specification covers the general requirements for steel sheet in coils and cut lengths. It applies to the following specifications that describe carbon steel, structural steel, and high-strength, low-alloy steel (HSLA) furnished as hot-rolled sheet and cold-rolled sheet: Specifications A414/A414M, A424, A606, A659/A659M, A794, A1008/A1008M, A1011/A1011M, and A1039/A1039M. 1.2x00a0;This specification is not applicable to hot-rolled heavy-thickness carbon sheet coils (Specification A635/A635M). 1.3x00a0;In case of any conflict in requirements, the requirements of the individual material specification shall prevail over those of this general specification. 1.4x00a0;For the purposes of determining conformance with this and the appropriate product specification referenced in 1.1, values shall be rounded to the nearest unit in the right hand place of figures used in expressing the limiting values in accordance with the rounding method of Practice E29. 1.5x00a0;Annex A1 lists permissible variations in dimensions and mass (see Note 1) in SI [metric] units. The values listed are not exact conversions of the values listed in the inch-pound tables, but instead are rounded or rationalized values. Conformance to Annex A1 is mandatory when the x201c;Mx201d; specification is used. Note 1x2014;The term weight is used when inch-pound units are the standard. However, under SI the preferred term is mass. 1.6x00a0;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.7x00a0;This specification a......
信息：ICS：77.140.50 (Flat steel products and semi-products) CCS：H46 发布：2013 实施：

ASTM A568/A568M-05a 热轧和冷轧碳素结构钢薄板和高强度低合金钢薄板的一般要求
简介：
信息：ICS：77.140.50 CCS： 发布：2005-12-01 实施：

简介： 信息：

ASTM A568/A568M-2013ae1 高强度低合金热轧及冷轧结构性碳素钢片材的标准规格.通用要求
简介：1.1x00a0;This specification covers the general requirements for steel sheet in coils and cut lengths. It applies to the following specifications that describe carbon steel, structural steel, and high-strength, low-alloy steel (HSLA) furnished as hot-rolled sheet and cold-rolled sheet: Specifications A414/A414M, A424, A606, A659/A659M, A794, A1008/A1008M, A1011/A1011M, and A1039/A1039M. 1.2x00a0;This specification is not applicable to hot-rolled heavy-thickness carbon sheet coils (Specification A635/A635M). 1.3x00a0;In case of any conflict in requirements, the requirements of the individual material specification shall prevail over those of this general specification. 1.4x00a0;For the purposes of determining conformance with this and the appropriate product specification referenced in 1.1, values shall be rounded to the nearest unit in the right hand place of figures used in expressing the limiting values in accordance with the rounding method of Practice E29. 1.5x00a0;Annex A1 lists permissible variations in dimensions and mass (see Note 1) in SI [metric] units. The values listed are not exact conversions of the values listed in the inch-pound tables, but instead are rounded or rationalized values. Conformance to Annex A1 is mandatory when the x201c;Mx201d; specification is used. Note 1x2014;The term weight is used when inch-pound units are the standard. However, under SI the preferred term is mass. 1.6x00a0;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.7x00a0;This specification and the applicable material specifications are expressed in both inch-pound units and SI units. However, unless the order specifies the applicable x201c;Mx201d; specification designation (SI units), the material shall be furnished to inch-pound units.
信息：ICS：77.140.50 (Flat steel products and semi-products) CCS： 发布：2013 实施：

ASTM A568/A568M-05 热轧和冷轧碳素钢薄板和低合金高强度钢的一般要求
简介：
信息：ICS：77.140.50 CCS： 发布：2005-05-01 实施：

简介： 信息：

ASTM A568/A568M-11b 热轧和冷轧低合金结构和高强度碳素钢薄板的一般要求
简介：
信息：ICS：77.140.50 CCS： 发布：2011-10-01 实施：

ASTM A568/A568M-2005
简介：1.1 This specification covers the general requirements for steel sheet in coils and cut lengths. It applies to the following specifications that describe carbon steel, structural steel, and high-strength, low-alloy steel (HSLA) furnished as hot-rolled sheet and cold-rolled sheet: Specifications A 414/A 414M, A 424, A 606, A 659/A 659M, A 794, A 1008/A 1008M, and A 1011/A 1011M. 1.2 This specification is not applicable to hot-rolled heavy-thickness carbon sheet coils (Specification A 635/A 635M).1.3 In case of any conflict in requirements, the requirements of the individual material specification shall prevail over those of this general specification. 1.4 For the purposes of determining conformance with this and the appropriate product specification referenced in , values shall be rounded to the nearest unit in the right hand place of figures used in expressing the limiting values in accordance with the rounding method of Practice E 29.1.5 lists permissible variations in dimensions and mass (see Note 0) in SI [metric] units. The values listed are not exact conversions of the values listed in the inch-pound tables, but instead are rounded or rationalized values. Conformance to is mandatory when the "M" specification is used. The term weight is used when inch-pound units are the standard. However, under SI the preferred term is mass. 1.6 The values stated in either inch-pound units or SI units are to be regarded as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.1.7 This specification and the applicable material specifications are expressed in both inch-pound units and SI units. However, unless the order specifies the applicable "M" specification designation (SI units), the material shall be furnished to inch-pound units.
信息：ICS：77.140.50 (Flat steel products and semi-products) CCS： 发布：2005 实施：

简介： 信息：

ASTM A568/A568M-11a 热轧和冷轧低合金结构和高强度碳素钢薄板的一般要求
简介：
信息：ICS：77.140.50 CCS： 发布：2011-05-01 实施：

ASTM A568/A568M-04a 热轧和冷轧碳素钢薄板和低合金高强度钢的一般要求
简介：
信息：ICS：77.140.50 CCS： 发布：2004-12-01 实施：

简介： 信息：

ASTM A568/A568M-11 热轧和冷轧低合金结构和高强度碳素钢薄板的一般要求
简介：
信息：ICS：77.140.50 CCS： 发布：2011-04-01 实施：

ASTM A568/A568M-04 热轧和冷轧碳素钢薄板和低合金高强度钢的一般要求
简介：
信息：ICS：77.140.50 CCS： 发布：2004-10-01 实施：

简介： 信息：

ASTM A568/A568M-09ae1 热轧和冷轧低合金结构和高强度碳素钢薄板的一般要求
简介：
信息：ICS：77.140.50 CCS： 发布：2011-02-09 实施：

ASTM A568/A568M-2004
简介：1.1 This specification covers the general requirements for steel sheet in coils and cut lengths. It applies to the following specifications that describe carbon steel, structural steel, and high-strength, low-alloy steel (HSLA) furnished as hot-rolled sheet and cold-rolled sheet: Specifications A 414/A 414M, A 424, A 606, A 659/A 659M, A 794, A 1008/A 1008M, and A 1011/A 1011M. 1.2 This specification is not applicable to hot-rolled heavy-thickness carbon sheet coils (Specification A 635/A 635M).1.3 In case of any conflict in requirements, the requirements of the individual material specification shall prevail over those of this general specification. 1.4 For the purposes of determining conformance with this and the appropriate product specification referenced in , values shall be rounded to the nearest unit in the right hand place of figures used in expressing the limiting values in accordance with the rounding method of Practice E 29.1.5 lists permissible variations in dimensions and mass (see Note 0) in SI [metric] units. The values listed are not exact conversions of the values listed in the inch-pound tables, but instead are rounded or rationalized values. Conformance to is mandatory when the "M" specification is used. The term weight is used when inch-pound units are the standard. However, under SI the preferred term is mass. 1.6 The values stated in either inch-pound units or SI units are to be regarded as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.1.7 This specification and the applicable material specifications are expressed in both inch-pound units and SI units. However, unless the order specifies the applicable "M" specification designation (SI units), the material shall be furnished to inch-pound units.
信息：ICS：77.140.50 (Flat steel products and semi-products) CCS： 发布：2004 实施：

简介： 信息：