ISO 8434-1检测标准

发布时间：2023-02-04 09:26:33 • 阅读量： • 来源：中析研究所

ISO 8434-1相关标准参考信息

ISO 12151-2-2022 液压传动和通用连接件.软管配件.第2部分:带ISO 8434-1 24°锥形连接器端部和O形圈的软管配件
简介：
信息：ICS：23.100.40 CCS：发布：2022-10-14 实施：

DIN EN ISO 8434-1-2018
简介：The document specifies general and dimensional requirements for the design and performance of 24° compression fittings which are suitable for the use with tubes with outside diameters from 4 mm to 42 mm.
信息：ICS：23.100.40 CCS：发布：2018-11-00 实施：

BS EN ISO 8434-1-2018 液压传动和通用金属管连接. 24度角连接器
简介：
信息：ICS：23.100.40 CCS：J15 发布：2018-09-06 实施：2018-09-06

EN ISO 8434-1-2018
简介：
信息：ICS：23.100.40 CCS：发布：2018-08-01 实施：

ISO 8434-1:2018 流体动力和一般用途的金属管连接件.第1部分:24度；锥形连接器
简介：
信息：ICS：23.100.40 CCS：发布：2018-07-27 实施：

ISO 8434-1-2018 液压传动和通用金属管连接件.第1部分:24°锥形接头
简介：
信息：ICS：23.100.40 CCS：J15 发布：2018-0701 实施：

DIN EN ISO 8434-1 Berichtigung 1-2009 液压传动和一般用途的金属管连接件.第1部分:24度锥形连接件(ISO 8434-1-2007).德文版本EN ISO 8434-1-2007,DIN EN ISO 8434-1-2008-02标准的勘误表.德文版本EN ISO 8434-1-2007/AC-2009
简介：
信息：ICS：23.100.40 CCS：J20 发布：2009-09 实施：

LST EN ISO 8434-1-2007/AC-2009
简介：
信息：ICS：23.100.40 CCS：发布：2009-07-27 实施：2009-07-27

DS/EN ISO 8434-1-2009
简介：This part of ISO 8434 specifies the general and dimensional requirements for 24° cone connectors using cutting ring and O-ring seal cone (referred to as DKO) suitable for use with ferrous and non-ferrous tubes with outside diameters from 4 mm to 42 mm inclusive. These connectors are for use in fluid power and general applications within the limits of pressure and temperature specified in this part of ISO 8434.They are intended for the connection of plain end tubes and hose fittings to ports in accordance withISO 6149-1, ISO 1179-1 and ISO 9974-1. (See ISO 12151-2 for related hose fitting specification.)These connectors provide full-flow connections in hydra
信息：ICS：23.100.40 CCS：发布：2009-07-24 实施：2009-07-24

DIN EN ISO 8434-1-2008 液压传动和通用金属管连接件.第1部分:24度锥形接头(ISO 8434-1-2007).德文版本EN ISO 8434-1-2007
简介：This pad of ISO 8434 specifies the general and dimensional requirements for 24' cone connectors usingcutting ring and O-ring seal cone (referred to as DKO) suitable for use with ferrous and non-ferrous tubes withoutside diameters from 4 mm to 42 mm inclusive. These connectors are for use in fluid power and generalapplications within the limits of pressure and temperature specified in this part of ISO 8434.They are intended for the connection of plain end tubes and hose fittings to ports in accordance withISO 6149-1, ISO 1179-1 and ISO 9974-1. (See ISO 12151-2 for related hose fitting specification.)These connectors provide full-flow connections in hydraulic systems operating to the working pressuresshown in Table 1. Because many factors influence the pressure at which a system performs satisfactorily,these values are not to be understood as guaranteed minimums. For every application, sufficient testing willneed to be conducted and reviewed by both the user and manufacturer to ensure that required performancelevels are met.NOTE 1 For new designs in hydraulic fluid power applications, see the requirements given in 9.6. Where therequirements of the application allow for the use of elastomeric seals, connector designs that conform to InternationalStandards and incorporate elastomeric sealing are preferred.NOTE 2 For use under conditions outside the pressure and/or temperature limits specified, see 5.4.This part of ISO 8434 also specifies a performance and qualification test for these connectors.
信息：ICS：23.100.40 CCS：J15 发布：2008-02 实施：

LST EN ISO 8434-1-2007
简介：
信息：ICS：23.100.40 CCS：发布：2007-12-28 实施：2007-12-28

DS/EN ISO 8434-1-2007
简介：This part of ISO 8434 specifies the general and dimensional requirements for 24° cone connectors using cutting ring and O-ring seal cone (referred to as DKO) suitable for use with ferrous and non-ferrous tubes with outside diameters from 4 mm to 42 mm inclusive. These connectors are for use in fluid power and general applications within the limits of pressure and temperature specified in this part of ISO 8434.They are intended for the connection of plain end tubes and hose fittings to ports in accordance withISO 6149-1, ISO 1179-1 and ISO 9974-1. (See ISO 12151-2 for related hose fitting specification.)These connectors provide full-flow connections in hydra
信息：ICS：23.100.40 CCS：发布：2007-12-02 实施：2007-12-02

BS EN ISO 8434-1-2007 液压传动和通用金属管连接.24度角连接器
简介：This part of ISO 8434 specifies the general and dimensional requirements for 24° cone connectors using cutting ring and O-ring seal cone (referred to as DKO) suitable for use with ferrous and non-ferrous tubes with outside diameters from 4 mm to 42 mm inclusive. These connectors are for use in fluid power and general applications within the limits of pressure and temperature specified in this part of ISO 8434. They are intended for the connection of plain end tubes and hose fittings to ports in accordance with ISO 6149-1, ISO 1179-1 and ISO 9974-1. (See ISO 12151-2 for related hose fitting specification.) These connectors provide full-flow connections in hydraulic systems operating to the working pressures shown in Table 1. Because many factors influence the pressure at which a system performs satisfactorily, these values are not to be understood as guaranteed minimums. For every application, sufficient testing will need to be conducted and reviewed by both the user and manufacturer to ensure that required performance levels are met. NOTE 1 For new designs in hydraulic fluid power applications, see the requirements given in 9.6. Where the requirements of the application allow for the use of elastomeric seals, connector designs that conform to International Standards and incorporate elastomeric sealing are preferred. NOTE 2 For use under conditions outside the pressure and/or temperature limits specified, see 5.4. This part of ISO 8434 also specifies a performance and qualification test for these connectors.
信息：ICS：23.100.40 CCS：J15 发布：2007-09-28 实施：2007-09-28

EN ISO 8434-1-2007 液压传动和通用金属管连接件.第1部分:24度锥形接头.合并勘误表-2009年4月
简介：This part of ISO 8434 specifies cutting ring and O-ring seal cone outside diameters from 4 mm toThe general (referred to and dimensional requirements for 240 cone connectors using as DKO) suitable for use with ferrous and non-ferrous tubes with 42 mm inclusive.These connectors are for use in fluid power and general applications withinThe limits of pressure and temperature specified inThis part of ISO 8434.
信息：ICS：23.100.40 CCS：发布：2007-09-01 实施：

ISO 8434-1-2007 液压传动和通用金属管连接件.第1部分:24°锥形接头
简介：This part of ISO 8434 specifies the general and dimensional requirements for 24° cone connectors usingcutting ring and O-ring seal cone (referred to as DKO) suitable for use with ferrous and non-ferrous tubes withoutside diameters from 4 mm to 42 mm inclusive. These connectors are for use in fluid power and generalapplications within the limits of pressure and temperature specified in this part of ISO 8434.They are intended for the connection of plain end tubes and hose fittings to ports in accordance withISO 6149-1, ISO 1179-1 and ISO 9974-1. (See ISO 12151-2 for related hose fitting specification.)These connectors provide full-flow connections in hydraulic systems operating to the working pressuresshown in Table 1. Because many factors influence the pressure at which a system performs satisfactorily,these values are not to be understood as guaranteed minimums. For every application, sufficient testing willneed to be conducted and reviewed by both the user and manufacturer to ensure that required performancelevels are met.NOTE 1 For new designs in hydraulic fluid power applications, see the requirements given in 9.6. Where therequirements of the application allow for the use of elastomeric seals, connector designs that conform to InternationalStandards and incorporate elastomeric sealing are preferred.NOTE 2 For use under conditions outside the pressure and/or temperature limits specified, see 5.4.This part of ISO 8434 also specifies a performance and qualification test for these connectors.
信息：ICS：23.100.40 CCS：J15 发布：2007-09 实施：

ISO 8434-1:2007 流体动力和通用金属管接头第1:24度锥形接头
简介：
信息：ICS：23.100.40 CCS：发布：2007-08-23 实施：

NF E48-079-2-2007 液压传动和通用联接件.软管接头.第2部分:带ISO 8434-1和ISO 8434-4的O形圈的圆锥形连接器末端的软管接头
简介：
信息：ICS：23.040.70;23.100.40 CCS：J20 发布：2007-01-01 实施：2007-01-05

KS B ISO 12151-2-2006(2016) 液压油功率连接和一般用途 - 软管接头 - 第2部分:带Iso 8434-1和Iso 8434-4的软管接头带O形圈的24度锥形连接器端
简介：
信息：ICS： CCS：发布：2006-06-13 实施：

KS B ISO 12151-2-2006 液压传动和通用连接件.软管接头.第2部分:使用O形圈的KS B ISO 8434-1与KS B ISO 8434-4.24°锥形末端的软管接头
简介：이 규격은 KS B ISO 8434-1 및 KS B ISO 8434-4에 따라 적용하는 O
信息：ICS：23.040.70;23.100.40 CCS：J10 发布：2006-06-13 实施：2006-06-13