燃料实验室检测标准燃料实验室-中析研究所检测

(CMA)

(CNAS)

(ISO)

(高新技术企业)

燃料实验室相关标准参考信息

GB/T 21452-2008 中间馏分燃料颗粒物含量的测定.实验室过滤法
简介：警告：本标准可能涉及某些危险材料、操作和设备，但并未对使用中涉及到的所有安全问题都提出建议。因此在使用本标准前，用户有责任建立合适的安全和健康措施并制定相应的管理制度。本标准适用于测定闭口闪点不低于38℃（采用GB/T 261测定）的中间馏分燃料的颗粒物含量，不适用于测定轻馏分燃料（如汽油）或喷气燃料。对于柴油发动机和民用的中间馏分燃料中颗粒物含量的限制，可以防止过滤器堵塞以及其他操作问题。本标准测定范围不大于25g/m。
信息：ICS：75.160.20 CCS：E31 发布：2008-02-13 实施：2008-09-01

GOST 33510-2015 固体再生燃料. 实验室样品的试样制备方法
简介：
信息：ICS：75.160.10 CCS：D20 发布：2015 实施：2017-01-01

ASTM D7717-2011(2017) 制备实验室分析用变性燃料乙醇和汽油混合基料体积混合的标准实施规程
简介：5.1x00a0;Typically, denatured fuel ethanol is added to gasoline blendstocks after production. For laboratories to test a sample that is similar to the finished fuel available in the market, it is important to provide a laboratory practice that standardizes the preparation of a blend of denatured fuel ethanol and gasoline blendstock. 5.2x00a0;The laboratory blend shall be prepared volumetrically to yield a fuel similar to that produced for consumer use. 5.3x00a0;When applicable, blends shall meet requirements of CFR 40.80, Subpart Dx2014;Reformulated Gasoline. 1.1x00a0;This practice covers and provides instructions on making a volumetric blend of denatured fuel ethanol with gasoline blendstocks, such as a reformulated gasoline blendstock for oxygenate blending (RBOB) or a conventional gasoline blendstock for oxygenate blending (CBOB). 1.2x00a0;This practice does not preclude the use of automated volumetric blending systems. 1.3x00a0;The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.5x00a0;This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
信息：ICS：75.160.20 CCS：E31 发布：2011 实施：

ASTM D6792-22 石油产品、液体燃料和润滑剂试验实验室质量管理体系的标准实施规程
简介：
信息：ICS：75.080 CCS：发布：2022-07-01 实施：

GOST 33509-2015 固体再生燃料. 实验室样品的制备方法
简介：
信息：ICS：75.160.10 CCS：D20 发布：2015 实施：2017-01-01

ASTM D6217-2011 实验室过滤法测定中间馏分燃料的颗粒物污染的标准试验方法
简介：This is the first ASTM standard test method for assessing the mass quantity of particulates in middle distillate fuels. Test Method D5452 and its predecessor Test Method D2276 were developed for aviation fuels and used 1 gal or 5 L of fuel sample. Using 1 gal of a middle distillate fuel, which can contain greater particulate levels, often required excessive time to complete the filtration. This test method used about a quarter of the volume used in the aviation fuel methods. The mass of particulates present in a fuel is a significant factor, along with the size and nature of the individual particles, in the rapidity with which fuel system filters and other small orifices in fuel systems can become plugged. This test method provides a means of assessing the mass of particulates present in a fuel sample. The test method can be used in specifications and purchase documents as a means of controlling particulate contamination levels in the fuels purchased. Maximum particulate levels are specified in several military fuel specifications.1.1 This test method covers the determination of the mass of particulate contamination in a middle distillate fuel by filtration. This test method is suitable for all No. 1 and No. 2 grades in Specifications D396, D975, D2880 and D3699 and for grades DMA and DMB in Specification D2069. 1.2 This test method is not suitable for fuels whose flash point as determined by Test Methods D56, D93 or D3828 is less than 38x00B0;C. Note 18212;Middle distillate fuels with flash points less than 38x00B0;C have been ignited by discharges of static electricity when the fuels have been filtered through inadequately bonded or grounded membrane filter systems. See Test Methods D2276 and D5452 for means of determining particulate contamination in Specification D1655 aviation turbine fuels and other similar aviation fuels. See Guide D4865 for a more detailed discussion of static electricity formation and discharge. 1.3 This test method has not been validated for testing biodiesel, such as meeting Specification D6751 or blends of middle distillates and biodiesel, such as meeting Specification D7467, or both. Test Method D7321 has been determined to be suitable for testing B100 and all blends of middle distillates......
信息：ICS：75.160.20 (Liquid fuels) CCS：E31 发布：2011 实施：

ASTM D6792-21c 石油产品、液体燃料和润滑剂试验实验室质量管理体系的标准实施规程
简介：
信息：ICS：75.080 CCS：发布：2021-12-01 实施：

GOST 33510-2015 固体再生燃料. 实验室样品的试样制备方法
简介：
信息：ICS：75.160.10 CCS：发布：2015 实施：2017-01-01

ASTM D7321-2011 用实验室过滤法测定生物柴油(B100)混合燃料生物柴油酯和生物柴油混合燃料中颗粒状污染物的标准试验方法
简介：The mass of particulates present in a fuel is a significant factor, along with the size and nature of the individual particles, in the rapidity with which fuel system filters and other small orifices in fuel systems can become plugged. This test method provides a means of assessing the mass of particulates present in a fuel sample. The test method can be used in specifications and purchase documents as a means of controlling particulate contamination levels in the fuels purchased.1.1 This test method covers the determination of the mass of particulate contamination in B100 biodiesel in accordance with Specification D6751 and BXX blends that are prepared against all No. 1 and No. 2 grade fuels allowed within Specifications D396 and D975. Note 18212;Middle distillate fuels with flash points less than 38x00B0;C have been ignited by discharges of static electricity when the fuels have been filtered through inadequately bonded or grounded glass fiber filter systems. See Guide D4865 for a more detailed discussion of static electricity formation and discharge. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：75.160.20 CCS：E31 发布：2011 实施：

ASTM D6792-21b 石油产品、液体燃料和润滑剂试验实验室质量管理体系的标准实施规程
简介：
信息：ICS：75.080 CCS：发布：2021-11-15 实施：

GOST 33132-2014 变性燃料酒精. 用于实验室分析的汽油混合燃料的体积混合物的制备实施规程
简介：
信息：ICS：75.160.20 CCS：发布：2014 实施：2016-07-01

ASTM D6217-10 实验室过滤中馏分燃料颗粒污染的标准试验方法
简介：
信息：ICS：75.160.20 CCS：发布：2010-08-01 实施：

ASTM D6217-21 实验室过滤法测定中间馏分燃料中微粒污染的标准试验方法
简介：
信息：ICS：75.160.20 CCS：发布：2021-10-01 实施：

GOST 8.616-2013 确保测量一致性的国家系统. 用于控制液化烃燃料气体组成成分的实验室和流色谱仪. 验证方法
简介：
信息：ICS：17.020;17.040.30 CCS：发布：2013 实施：2015-02-01

GOST R 54274-2010 (2019) 航空燃料.微粒子污染的实验室过滤测定法
简介：
信息：ICS： CCS：发布：2010-01-01 实施：2010-01-01

ASTM D7717-11(2021) 实验室分析用变性燃料乙醇和汽油混合料容量混合制备的标准实施规程
简介：
信息：ICS：75.160.20 CCS：发布：2021-10-01 实施：

ASTM D5452-12 实验室过滤对航空燃料颗粒污染的标准试验方法
简介：
信息：ICS：75.160.20 CCS：发布：2012-06-01 实施：

ASTM D6217-2010 实验室过滤法测定中间馏分燃料的颗粒物污染的标准试验方法
简介：This is the first ASTM standard test method for assessing the mass quantity of particulates in middle distillate fuels. Test Method D5452 and its predecessor Test Method D2276 were developed for aviation fuels and used 1 gal or 5 L of fuel sample. Using 1 gal of a middle distillate fuel, which can contain greater particulate levels, often required excessive time to complete the filtration. This test method used about a quarter of the volume used in the aviation fuel methods. The mass of particulates present in a fuel is a significant factor, along with the size and nature of the individual particles, in the rapidity with which fuel system filters and other small orifices in fuel systems can become plugged. This test method provides a means of assessing the mass of particulates present in a fuel sample. The test method can be used in specifications and purchase documents as a means of controlling particulate contamination levels in the fuels purchased. Maximum particulate levels are specified in several military fuel specifications.1.1 This test method covers the determination of the mass of particulate contamination in a middle distillate fuel by filtration. This test method is suitable for all No. 1 and No. 2 grades in Specifications D396, D975, D2880 and D3699 and for grades DMA and DMB in Specification D2069. 1.2 This test method is not suitable for fuels whose flash point as determined by Test Methods D56, D93 or D3828 is less than 38x00B0;C. Note 18212;Middle distillate fuels with flash points less than 38x00B0;C have been ignited by discharges of static electricity when the fuels have been filtered through inadequately bonded or grounded membrane filter systems. See Test Methods D2276 and D5452 for means of determining particulate contamination in Specification D1655 aviation turbine fuels and other similar aviation fuels. See Guide D4865 for a more detailed discussion of static electricity formation and discharge. 1.3 This test method has not been validated for testing biodiesel, such as meeting Specification D6751 or blends of middle distillates and biodiesel, such as meeting Specification D7467, or both. Test Method D7321 has been determined to be suitable for testing B100 and all blends of middle distillates......
信息：ICS：75.160.20 CCS：E31 发布：2010 实施：

ASTM D6792-21a 石油产品、液体燃料和润滑剂试验实验室质量管理体系的标准实施规程
简介：
信息：ICS：75.080 CCS：发布：2021-08-01 实施：

ANSI/ASTM D5452-2012 通过实验室过滤的航空燃料中颗粒污染物用试验方法
简介：
信息：ICS：75.160.20 CCS：E31 发布：2012 实施：

GOST R 54274-2010 航空燃料.微粒子污染的实验室过滤测定法
简介：
信息：ICS：75.160.20 CCS：发布：2010 实施：2012-07-01

ASTM D6792-21 石油产品、液体燃料和润滑剂试验实验室质量管理体系的标准实施规程
简介：
信息：ICS：75.080 CCS：发布：2021-07-01 实施：

ASTM D5452-2012 用实验室过滤法测定航空燃料中颗粒污染物的标准试验方法
简介：5. Significance and UseTop Bottom 5.1 This test method provides a gravimetric measurement of the particulate matter present in a sample of aviation turbine fuel delivered to a laboratory for evaluation. The objective is to minimize these contaminants to avoid filter plugging and other operational problems. Although tolerable levels of particulate contaminants have not yet been established for all points in fuel distribution systems, the total contaminant measurement is normally of most interest. 1.1 This test method covers the gravimetric determination by filtration of particulate contaminant in a sample of aviation turbine fuel delivered to a laboratory. 1.1.1 The sample is filtered through a test membrane and a control membrane using vacuum. The mass change difference identifies the contaminant level per unit volume. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see 4.2, 7.3, 7.5, 11.2, and X1.7.2. Before using this standard, refer to supplierx0027;s safety labels, material safety data sheets, and technical literature.
信息：ICS：75.160.20 (Liquid fuels) CCS：E31 发布：2012 实施：

GOST R 54229-2010 固体回收燃料.实验室样品中试验样品的制备方法
简介：
信息：ICS：75.160.10 CCS：发布：2010 实施：2012-07-01

ASTM D6792-20 石油产品液体燃料和润滑油检测实验室质量管理体系的标准实践
简介：
信息：ICS：75.080 CCS：发布：2020-09-15 实施：

NF X34-227-2011 固体回收燃料.从实验室样本中试样的制备方法.
简介：
信息：ICS：75.160.10 CCS：D21 发布：2011-11-01 实施：2011-11-19

GOST R 54228-2010 固体回收燃料.实验室样品制备方法
简介：
信息：ICS：75.160.10 CCS：发布：2010 实施：2012-07-01

ASTM D5452-20 实验室过滤对航空燃料颗粒污染的标准试验方法
简介：
信息：ICS：75.160.20 CCS：发布：2020-09-01 实施：

DIN EN 15413-2011 固体回收燃料.从实验室样品中制备试验样品的方法;德文版本EN 15413-2011
简介：
信息：ICS：75.160.10 CCS：D20 发布：2011-11 实施：

API RP 1543-2009 (2019) 从炼油厂到机场运送期间航空燃料的文献、监测和实验室试验
简介：
信息：ICS： CCS：发布：2009-01-01 实施：2009-01-01

ISO/TS 20048-1-2020 固体生物燃料.排气和耗氧特性的测定.第1部分:用封闭容器测定排气和耗氧的实验室方法
简介：
信息：ICS： CCS：发布：2020-03-31 实施：

BS EN 15413-2011 固体回收燃料.利用实验室样品制备试验样品的方法
简介：
信息：ICS：75.160.10 CCS：D20 发布：2011-09-30 实施：2011-09-30

ASTM D6217-98(2008) 实验室过滤中馏分燃料颗粒污染的标准试验方法
简介：
信息：ICS：75.160.20 CCS：发布：2008-12-01 实施：

ASTM D6217-18 实验室过滤中馏分燃料颗粒污染的标准试验方法
简介：
信息：ICS：75.160.20 CCS：发布：2018-07-01 实施：

EN 15413-2011 固体回收燃料.利用实验室样品制备试验样品的方法
简介：This European Standard specifies the correct sequence of operations to ensure the representativity of the test portions that have been taken according to the sampling plan, prior to physical and/or chemical analysis (e. g. extractions, digestion and/or analytical determinations) of solid samples.This European Standard specifies the correct sequence of operations and treatments to be applied to the laboratory sample in order to obtain suitable test portions in compliance with the specific requirements defined in the corresponding analytical procedures.
信息：ICS：75.160.10 CCS：发布：2011-09-01 实施：

ASTM D5452-08 实验室过滤对航空燃料颗粒污染的标准试验方法
简介：
信息：ICS：75.160.20 CCS：发布：2008-05-01 实施：

ANSI/ASTM D6792-2017 石油产品, 液态燃料和润滑剂测试实验室质量管理体系的标准实施规程
简介：
信息：ICS：75.100 CCS：E30 发布：2017-05-01 实施：

NF X34-229-2011 固体可回收燃料的实验室样品制备方法.
简介：
信息：ICS：75.160.10 CCS：D21 发布：2011-08-01 实施：2011-08-06

ASTM D7321-2008 用实验室过滤法测试生物柴油B100调合生物柴油酯和生物柴油混合燃料的颗粒污染的标准试验方法
简介：The mass of particulates present in a fuel is a significant factor, along with the size and nature of the individual particles, in the rapidity with which fuel system filters and other small orifices in fuel systems can become plugged. This test method provides a means of assessing the mass of particulates present in a fuel sample. The test method can be used in specifications and purchase documents as a means of controlling particulate contamination levels in the fuels purchased.1.1 This test method covers the determination of the mass of particulate contamination in B100 biodiesel in accordance with Specification D 6751 and BXX blends that are prepared against all No. 1 and No. 2 grade fuels allowed within Specifications D 396, D 975, D 2880, and D 3699. Note 18212;Middle distillate fuels with flash points less than 38x00B0;C have been ignited by discharges of static electricity when the fuels have been filtered through inadequately bonded or grounded glass fiber filter systems. See Guide D 4865 for a more detailed discussion of static electricity formation and discharge. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：75.160.20 CCS：E31 发布：2008 实施：

ASTM D6792-17 石油产品液体燃料和润滑油检测实验室质量管理体系的标准实践
简介：
信息：ICS：75.080 CCS：发布：2017-05-01 实施：

ASTM D6217-11 实验室过滤中馏分燃料颗粒污染的标准试验方法
简介：
信息：ICS：75.160.20 CCS：发布：2011-06-01 实施：

ASTM D5452-2008 用实验室过滤法测定航空燃料中颗粒污染物的试验方法
简介：This test method provides a gravimetric measurement of the particulate matter present in a sample of aviation turbine fuels delivered to a laboratory for evaluation. The objective is to minimize these contaminants to avoid filter plugging and other operational problems. Although tolerable levels of particulate contaminants have not yet been established for all points in fuel distribution systems, the total contaminant measurement is normally of most interest.1.1 This test method covers the gravimetric determination by filtration of particulate contaminant in a sample of aviation turbine fuel delivered to a laboratory. 1.1.1 The sample is filtered through a test membrane and a control membrane using vacuum. The mass change difference identifies the contaminant level per unit volume. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see 4.2, 7.3, 7.5, 11.2, and X1.7.2. Before using this standard, refer to supplier's safety labels, material safety data sheets, and technical literature.
信息：ICS：75.160.20 (Liquid fuels) CCS：E31 发布：2008 实施：

ASTM D7717-11(2017) 制备用于实验室分析的变性燃料乙醇和汽油混合物的体积共混物的标准实践
简介：
信息：ICS：75.160.20 CCS：发布：2017-05-01 实施：

ASTM D7717-11 制备用于实验室分析的变性燃料乙醇和汽油混合物的体积共混物的标准实践
简介：
信息：ICS：75.160.20 CCS：发布：2011-06-01 实施：

BS DD CEN/TS 15443-2006 固体再生燃料.实验室样品制备方法
简介：This Technical Specification describes methods for reducing combined samples to laboratory samples and laboratory samples to sub-samples and general analysis samples, and is applicable to solid recovered fuels that are either: fine and regularly-shaped particulate materials, particle sizes up to about 10 mm that can be sampledusing a scoop or pipe, for example: soft and hard pellets;? coarse or irregularly-shaped particulate materials, particle sizes up to about 200 mm that can be sampled using a shovel, for example: fluff, chips and chunks;? large pieces with nominal top size above 200 mm.The methods described in this Technical Specification may be used for sample preparation, for example, when the samples are to be tested for bulk density, biomass determination, durability, particle size distribution, moisture content, ash content, ash melting behaviour, calorific value, chemical composition, and impurities. The methods are not intended to be applied to the very large samples required for the testing of bridging properties.
信息：ICS：75.160.10 CCS：D20 发布：2007-02-28 实施：2007-02-28

ASTM D6792-2017 石油产品, 液态燃料和润滑剂测试实验室质量管理体系的标准实施规程
简介：4.1x00a0;A petroleum products, liquid fuels, and lubricants testing laboratory plays a crucial role in product quality management and customer satisfaction. It is essential for a laboratory to provide quality data. This document provides guidance for establishing and maintaining a quality management system in a laboratory. 4.1.1x00a0;The word x2018;customerx2019; can refer to both customers internal and external to the laboratory or organization. 1.1x00a0;This practice covers the establishment and maintenance of the essentials of a quality management system in laboratories engaged in the analysis of petroleum products, liquid fuels, and lubricants. It is designed to be used in conjunction with Practice D6299. Note 1:x00a0;This practice is based on the quality management concepts and principles advocated in ANSI/ISO/ASQ Q9000 standards, ISO/IEC 17025, ASQ Manual,2 and ASTM standards such as D3244, D4182, D4621, D6299, D6300, D7372, E29, E177, E456, E548, E882, E994, E1301, E1323, STP 15D,3 and STP 1209.4 1.2x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use. 1.3x00a0;This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
信息：ICS：75.080 ; 75.100 CCS：E30 发布：2017 实施：

DIN EN 15443-2011 固体回收燃料.实验室样品的备制方法;德文版本EN 15443-2011
简介：This European Standard specifies methods for reducing combined samples to laboratory samples and laboratory samples to sub-samples and general analysis samples.The methods described in this European Standard may be used for sample preparation, for example, when the samples are to be tested for bulk density, biomass determination, durability, particle size distribution,moisture content, ash content, ash melting behaviour, calorific value, chemical composition, and impurities.the methods are not intended to be applied to the very large samples required for the testing of bridging properties.
信息：ICS：75.160.10 CCS：D20 发布：2011-05 实施：

ASTM D5452-06 实验室过滤对航空燃料颗粒污染的标准试验方法
简介：
信息：ICS：75.160.20 CCS：发布：2006-12-01 实施：

ASTM D6217-11(2016) 实验室过滤中馏分燃料颗粒污染的标准试验方法
简介：
信息：ICS：75.160.20 CCS：发布：2016-12-01 实施：

BS EN 15443-2011 固体回收燃料.实验室样品的制备方法
简介：This European Standard specifies methods for reducing combined samples to laboratory samples andlaboratory samples to sub-samples and general analysis samples.The methods described in this European Standard may be used for sample preparation, for example, whenthe samples are to be tested for bulk density, biomass determination, durability, particle size distribution,moisture content, ash content, ash melting behaviour, calorific value, chemical composition, and impurities.The methods are not intended to be applied to the very large samples required for the testing of bridgingproperties.
信息：ICS：75.160.10 CCS：D20 发布：2011-03-31 实施：2011-03-31

BS DD CEN/TS 15413-2006 固体再生燃料.从实验室样品取样制备试样的方法
简介：This Technical Specification specifies the correct sequence of operations to ensure the representativity of thetest portions that has been taken according to the sampling plan, prior to physical and/or chemical analysis(e.g. extractions, digestion and/or analytical determinations) of solid samples.This Technical Specification specifies the correct sequence of operations and treatments to be applied to thelaboratory sample in order to obtain suitable test portions in compliance with the specific requirements definedin the corresponding analytical procedures.
信息：ICS：75.160.10 CCS：D20 发布：2006-10-31 实施：2006-10-31

ASTM E829-16 准备垃圾衍生燃料（RDF）实验室样品进行分析的标准实践
简介：
信息：ICS：13.030.50 CCS：发布：2016-02-01 实施：

EN 15443-2011 固体回收燃料.实验室样品的备制方法
简介：This European Standard specifies methods for reducing combined samples to laboratory samples and laboratory samples to sub-samples and general analysis samples. The methods described inThis European Standard may be used for sample preparation, for example, when the samples are to be tested for bulk density, biomass determination, durability, particle size distribution, moisture content, ash content, ash melting behaviour, calorific value, chemical composition, and impurities. The methods are not intended to be applied to the very large samples required for the testing of bridging properties.
信息：ICS：75.160.10 CCS：发布：2011-03-01 实施：

ASTM D5452-2006 实验室过滤法测定航空燃料中粒状污染物的标准试验方法
简介：This test method provides a gravimetric measurement of the particulate matter present in a sample of aviation turbine fuels delivered to a laboratory for evaluation. The objective is to minimize these contaminants to avoid filter plugging and other operational problems. Although tolerable levels of particulate contaminants have not yet been established for all points in fuel distribution systems, the total contaminant measurement is normally of most interest.1.1 This test method covers the gravimetric determination by filtration of particulate contaminant in a sample of aviation turbine fuel delivered to a laboratory.1.1.1 The sample is filtered through a test membrane and a control membrane using vacuum. The mass change difference identifies the contaminant level per unit volume.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see 4.2, 7.3, 7.5, 11.3, and X1.7.2. Before using this standard, refer to supplier's safety labels, material safety data sheets, and technical literature.
信息：ICS：75.160.20 (Liquid fuels) CCS：E31 发布：2006 实施：

ASTM E829-2016 制备分析用废弃物衍生燃料 (RDF) 实验室样品的标准实施规程
简介：5.1x00a0;Using this procedure a sample of RDF can be converted into a physical form suitable for laboratory fuel analysis. 5.2x00a0;As indicated in Test Method E791, air-dry moisture, which is determined by this procedure, is essential to the calculation of other laboratory results on an as-received basis. The air-dry moisture value is used in conjunction with the results of the residual moisture determination in Test Method E790 to calculate total sample moisture. 1.1x00a0;This practice covers the preparation of RDF laboratory samples for analysis, the laboratory samples having been previously obtained from representative RDF samples. 1.2x00a0;The determination of the air-dry loss of the RDF is part of this preparation procedure and must be performed prior to the particle size reduction. 1.3x00a0;The practice given may also be used for other RDF types but additional sample preparation steps may be necessary prior to the application of this method. 1.4x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements are given in Section 7.
信息：ICS： CCS：发布：2016 实施：

ASTM D7717-2011 用于实验室分析的配制变性燃料酒精和汽油掺混油混合物的标准操作规程
简介：Typically, denatured fuel ethanol is added to gasoline blendstocks after production. For laboratories to test a sample that is similar to the finished fuel available in the market, it is important to provide a laboratory practice that standardizes the preparation of a blend of denatured fuel ethanol and gasoline blendstock. The laboratory blend shall be prepared volumetrically to yield a fuel similar to that produced for consumer use. When applicable, blends shall meet requirements of CFR 40.80, Subpart DReformulated Gasoline.1.1 This practice covers and provides instructions on making a volumetric blend of denatured fuel ethanol with gasoline blendstocks, such as a reformulated gasoline blendstock for oxygenate blending (RBOB) or a conventional gasoline blendstock for oxygenate blending (CBOB). 1.2 This practice does not preclude the use of automated volumetric blending systems. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：75.160.20 (Liquid fuels) CCS：E31 发布：2011 实施：

ASTM D5452-05 实验室过滤对航空燃料颗粒污染的标准试验方法
简介：
信息：ICS：75.160.20 CCS：发布：2005-12-01 实施：

GOST 33510-2015 固体再生燃料. 实验室样品的试样制备方法
简介：
信息：ICS：75.160.10 CCS：发布：2015 实施：2017-01-01

ASTM D7321-2011e1 采用实验室过滤法测试生物柴油B100调合生物柴油酯和生物柴油混合燃料的颗粒污染试验方法的标准试验方法
简介：5.1x00a0;The mass of particulates present in a fuel is a significant factor, along with the size and nature of the individual particles, in the rapidity with which fuel system filters and other small orifices in fuel systems can become plugged. This test method provides a means of assessing the mass of particulates present in a fuel sample. 5.2x00a0;The test method can be used in specifications and purchase documents as a means of controlling particulate contamination levels in the fuels purchased. 1.1x00a0;This test method covers the determination of the mass of particulate contamination in B100 biodiesel in accordance with Specification D6751 and BXX blends that are prepared against all No. 1 and No. 2 grade fuels allowed within Specifications D396 and D975.Note 1x2014;Middle distillate fuels with flash points less than 38x00b0;C have been ignited by discharges of static electricity when the fuels have been filtered through inadequately bonded or grounded glass fiber filter systems. See Guide D4865 for a more detailed discussion of static electricity formation and discharge. 1.2x00a0;The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：75.160.20 (Liquid fuels) CCS：E31 发布：2011 实施：

ASTM D5452-2005 用实验室过滤法测定航空燃料中颗粒污染物的标准试验方法
简介：1.1 This test method covers the gravimetric determination by filtration of particulate contaminant in a sample of aviation turbine fuel delivered to a laboratory. 1.1.1 The sample is filtered through a test membrane and a control membrane using vacuum. The mass change difference identifies the contaminant level per unit volume. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see 4.2, 7.3, 7.5, 11.3 and X1.7.2. Before using this standard, refer to supplier''s safety labels, material safety data sheets, and technical literature.
信息：ICS：75.160.20 (Liquid fuels) CCS：发布：2005 实施：