动态剪切流变仪检测标准动态剪切流变仪-中析研究所检测

(CMA)

(CNAS)

(ISO)

(高新技术企业)

动态剪切流变仪相关标准参考信息

GB/T 33061.10-2016 塑料动态力学性能的测定第10部分：使用平行平板振荡流变仪测定复数剪切黏度
简介：
信息：ICS：83.080.01 CCS：G31 发布：2016-10-13 实施：2017-05-01 00:00:00.0

ASTM D7405-15 使用动态剪切流变仪的沥青粘合剂的多重应力蠕变和回收（MSCR）的标准测试方法
简介：
信息：ICS：91.100.50 CCS：发布：2015-12-01 实施：

ASTM D7654/D7654M-2010 使用动态剪切流变仪测定屋顶铺设用沥青的标准规范
简介：1.1 This specification covers two types of asphalt intended for use in built-up roof construction, construction of some modified bitumen systems, construction of bituminous vapor retarder systems, and for adhering insulation boards used in various types of roof systems. The specification is intended for general classification purposes only and does not imply restrictions on the slope at which an asphalt must be used. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：91.100.50 CCS：E43 发布：2010 实施：

ASTM D7552-22 使用动态剪切流变仪测定沥青混合料复合剪切模量（G*）的标准试验方法
简介：
信息：ICS：75.140 CCS：发布：2022-12-15 实施：

ASTM D6601-15 橡胶性能的标准试验方法&x2014；使用无转子剪切流变仪测量固化和固化后动态特性
简介：
信息：ICS：83.060 CCS：发布：2015-11-01 实施：

ASTM D7605-2010 用无转子剪切流变仪测量聚合物熔体流变性能和冻结动态性能的热塑性弹性体x2014; 的标准试验方法
简介：This test method is used to measure viscoelastic properties of thermoplastic elastomer polymer melts at elevated temperatures as well as the dynamic properties of the respective congealed thermoplastic elastomer specimens measured at lower temperatures. These polymer melt viscoelastic properties may relate to factory processing behavior while the dynamic properties of the respective congealed specimen may relate to product performance. This test method may be used for quality control in thermoplastic elastomer manufacturing processes, for quality control of received shipments of thermoplastic elastomers, and for research and development testing of thermoplastic elastomers. This method may also be used for evaluating processing and product performance differences resulting from the use of different compounding materials and process conditions in the making of these thermoplastic elastomers.1.1 This test method covers the use of a rotorless oscillating shear rheometer for the measurement of the flow properties of polymer melts and their respective congealed dynamic properties for thermoplastic elastomers (TPE) which includes thermoplastic vulcanizates (TPV). These flow properties and congealed dynamic properties are related to factory processing and product performance. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：83.100 CCS：H26;G32 发布：2010 实施：

ASTM D8059-19(2022) 用密封腔无转子剪切流变仪测量橡胶化合物未硫化动态应变软化（Payne效应）的标准试验方法
简介：
信息：ICS：83.060 CCS：发布：2022-11-01 实施：

BS ISO 6721-10-2015 塑料.动态机械性能的测定.使用平板振荡流变仪测定复合剪切粘度
简介：
信息：ICS：83.080.01 CCS：G31 发布：2015-10-31 实施：2015-10-31

ASTM D7405-2010a 使用动态剪切流变仪测定沥青粘合剂的多应力重复蠕变和恢复(MSCR)的标准试验方法
简介：This test method is used to identify the presence of elastic response in a binder and the change in elastic response at two different stress levels. Non-recoverable creep compliance has been shown to be an indicator of the resistance of an asphalt binder to permanent deformation under repeated load. This test method is also useful as a surrogate for other test methods used to measure elasticity in asphalt binders such as Test Method D5801 (Toughness and Tenacity), Test Method D6084 (Elastic Recovery), and Test Method D7175 (DSR phase angle).1.1 This test method covers the determination of percent recovery and non-recoverable creep compliance of asphalt binders by means of Multiple Stress Creep and Recovery (MSCR) testing. The MSCR test is conducted using the Dynamic Shear Rheometer (DSR) at a specified temperature. 1.2 This standard is appropriate for unaged material, material aged in accordance with Test Method D2872 (RTFO), material aged in accordance with Practice D6521 (PAV), and material aged in accordance with both Test Method D2872 and Practice D6521. Note 18212;The majority of development work on this test method was performed on material aged in accordance with Test Method D2872 (RTFO). 1.3 The percent recovery is intended to provide a means to determine the presence of elastic response and stress dependence of polymer modified and unmodified asphalt binders. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：91.100.50 CCS：E43 发布：2010 实施：

ASTM D7605-11(2022) 用无转子剪切流变仪测量聚合物熔体流变特性和凝固动态特性的热塑性弹性体的标准试验方法
简介：
信息：ICS：83.100 CCS：发布：2022-10-01 实施：

ASTM D7552-09 用动态剪切流变仪测定沥青混合物复剪切模量（G*）的标准试验方法
简介：
信息：ICS：75.140 CCS：发布：2009-07-01 实施：

ASTM D7405-20 使用动态剪切流变仪的沥青粘合剂的多重应力蠕变和回收（MSCR）的标准测试方法
简介：
信息：ICS：91.100.50 CCS：发布：2020-03-01 实施：

ISO 6721-10:2015 塑料 - 动态力学性能的测定 - 第10部分:使用平行板振荡流变仪的复合剪切粘度
简介：
信息：ICS：83.080.01 CCS：发布：2015-09-21 实施：

ASTM D7552-2009(2014) 采用动态剪切流变仪测定沥青混合物的复数切变模量 (G*) 用标准试验方法
简介：5.1x00a0;The complex shear modulus of bituminous mixtures is a fundamental property of the material. Test results at critical temperatures (Tcritical) are used for specifications for some mixes. Mixtures with stiffer binders, aged mixtures, mixtures with higher amounts of fines (material finer than 75x00b5;), and mixtures with lower voids all tend to have higher complex shear modulus values than mixtures with less stiff binders, unaged mixes, mixtures with low levels of fines and higher air voids. In general, mixtures with higher complex shear modulus values at a given service temperature will exhibit lower permanent deformation values than similar mixtures tested at the same temperature that have lower complex shear modulus values. Note 2:x00a0;The quality of the results produced by this standard are dependent on the competence of the personnel performing the procedure and the capability, calibration, and maintenance of the equipment used. Agencies that meet the criteria of Practice D3666 are generally considered capable of competent and objective testing/sampling/inspection/etc. Users of this standard are cautioned that compliance with Practice D3666 alone does not completely assure reliable results. Reliable results depend on many factors; following the suggestions of Practice D3666 or some similar acceptable guideline provides a means of evaluating and controlling some of those factors. 1.1x00a0;This test method covers the determination of the complex shear modulus of bituminous mixtures using torsion rectangular geometry on a dynamic shear rheometer (DSR). It is applicable to bituminous mixtures having complex shear modulus values greater than 1 x00d7; 104 Pa when tested over a range of temperatures from 10x00b0;C to 76x00b0;C at frequencies of 0.01 to 25 Hz and strains of 0.0018201;% to 0.18201;%. The determination of complex shear modulus is typically determined at 20x00b0;C to 70x00b0;C at 0.01% strain at 10 discrete frequency values covering 0.01 to 10 Hz. From these data, temperature or frequency master curves can be generated as required. This test method is intended for determining the complex shear modulus of bituminous mixtures as required for specification testing or quality control of bituminous mixture production. 1.2x00a0;This test method is appropriate for laboratory prepared and compacted mixtures, field produced and laboratory compacted mixtures or field cores, regardless of binder type or grade and regardless of whether RAP is used in the mixture. Due to the geometry of the specimens being tested this test method is not applicable to open-graded or SMA mixtures. It has been found to be appropriate for dense-graded mixtures, whether coarse- or fine-graded, with 19 mm or smaller nominal maximum aggregate size. 1.3x00a0;The between-laboratory reproducibility of this test method is being determined and will be available on or before June 2012. Therefore, this test method should not be used for acceptance or rejection of materials for purchasing purposes. 1.4x00a0;The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
信息：ICS：75.140;91.100.50 CCS：发布：2009 实施：

KS F 2393-2019 用于使用动态剪切流变仪沥青粘合剂的流变性能的标准试验方法
简介：
信息：ICS：75.140 CCS：发布：2019-12-31 实施：

ISO 6721-10-2015 塑料动态机械性能的测定第10部分:使用平板振荡流变仪测定复合剪切粘度
简介：
信息：ICS：83.080.01 CCS：G31 发布：2015-09 实施：

ASTM D7175-08 使用动态剪切流变仪测定沥青粘合剂的流变性能的标准测试方法
简介：
信息：ICS：93.080.20 CCS：发布：2008-07-15 实施：

ASTM D8059-19 橡胶化合物的标准试验方法&x2014；使用密封腔无转子剪切流变仪测量未硫化动态应变软化（佩恩效应）
简介：
信息：ICS：83.060 CCS：发布：2019-11-01 实施：

ASTM D7175-15 使用动态剪切流变仪测定沥青粘合剂的流变性能的标准测试方法
简介：
信息：ICS：93.080.20 CCS：发布：2015-07-01 实施：

ASTM D7405-08a 使用动态剪切流变仪测定沥青粘合剂多重应力蠕变和恢复（MSCR）的标准试验方法
简介：
信息：ICS：91.100.50 CCS：发布：2008-07-01 实施：

ASTM D8189-19 用动态剪切流变仪（DSR）测定沥青粘合剂和乳化沥青残渣粘性的标准试验方法
简介：
信息：ICS：91.100.50 CCS：发布：2019-07-01 实施：

ASTM D7175-2015 采用动态剪切流变仪测定沥青粘结剂流变特性的标准试验方法
简介：5.1x00a0;The test temperature for this test is related to the temperature experienced by the pavement in the geographical area for which the asphalt binder is intended to be used. 5.2x00a0;The complex shear modulus is an indicator of the stiffness or resistance of asphalt binder to deformation under load. The complex shear modulus and the phase angle define the resistance to shear deformation of the asphalt binder in the linear viscoelastic region. The complex modulus and the phase angle are used to calculate performance-related criteria in accordance with Specification D6373 or AASHTO Standard M320. 1.1x00a0;This test method covers the determination of the dynamic shear modulus and phase angle of asphalt binders when tested in dynamic (oscillatory) shear using parallel plate geometry. It is applicable to asphalt binders having dynamic shear modulus values in the range from 100 Pa to 10 MPa. This range in modulus is typically obtained between 4 and 88x00b0;C at 10 rad/s. This test method is intended for determining the linear viscoelastic properties of asphalt binders as required for specification testing and is not intended as a comprehensive procedure for the full characterization of the viscoelastic properties of asphalt binders. 1.2x00a0;This standard is appropriate for unaged materials, material aged in accordance with Test Method D2872, material aged in accordance with Practice D6521, or material aged in accordance with both Test Method D2872 and Practice D6521. This procedure is limited to asphalt binders that contain particles with largest dimension less than 250 x03bc;m. 1.3x00a0;The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4x00a0;This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：93.080.20 CCS：发布：2015 实施：

ASTM D6601-02(2008) 橡胶性能的标准试验方法使用无转子剪切流变仪测量固化和固化后动态特性
简介：
信息：ICS：83.060 CCS：发布：2008-05-01 实施：

ASTM D6601-19 橡胶性能的标准试验方法&x2014；使用无转子剪切流变仪测量固化和固化后动态特性
简介：
信息：ICS：83.060 CCS：发布：2019-05-01 实施：

ASTM D6601-2015 橡胶特性的标准试验方法. 采用无转子剪切流变仪测量橡胶在固化和固化后的动态特性
简介：5.1x00a0;This test method is used to determine the vulcanization characteristics of (vulcanizable) rubber compounds under selected test conditions of strain and frequency which do not significantly affect the cured dynamic properties. In the same test, this test method also will measure the dynamic properties of the vulcanizate at temperatures significantly below the cure temperature. These lower temperature measurements are necessary in order to more effectively relate to rubber product service conditions. 5.2x00a0;This test method may be used for quality control in rubber manufacturing processes and for research and development testing of rubber compounds containing curatives. This test method also may be used for evaluating cure and dynamic property differences resulting from the use of different compounding ingredients. 5.3x00a0;For additional information regarding the significance of dynamic testing of vulcanized rubber, the reader may wish to reference Guide D5992. 1.1x00a0;This test method covers the use of a rotorless oscillating shear rheometer for measuring after cure dynamic properties at predetermined temperature(s) below the cure temperature. 1.2x00a0;Specified cure conditions that approximate a x201c;static curex201d; also are covered to minimize effects on cured rubber compound dynamic properties. This test method is not intended to replace Test Method D5289. 1.3x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.4x00a0;Warningx2014;Compounds based on silicone or fluoroelastomers may have high levels of thermal contraction or poor adhesion to the dies when cooled after the cure portion of this test method, causing slippage during strain sweeps. If this occurs, the results will not be reliable.
信息：ICS：83.060 CCS：发布：2015 实施：

ASTM D7405-08 使用动态剪切流变仪的沥青粘合剂的多重应力蠕变和回收（MSCR）的标准测试方法
简介：
信息：ICS：91.100.50 CCS：发布：2008-02-01 实施：

ASTM D7654/D7654M-10(2018) 用动态剪切流变仪测量的屋面沥青的标准规范
简介：
信息：ICS：91.100.50 CCS：发布：2018-05-01 实施：

ASTM D7405-2015 使用动态剪切流变仪测定沥青粘合剂的多应力蠕变和恢复 (MSCR) 的标准试验方法
简介：5.1x00a0;This test method is used to identify the presence of elastic response in a binder and the change in elastic response at two different stress levels. Non-recoverable creep compliance has been shown to be an indicator of the resistance of an asphalt binder to permanent deformation under repeated load. 5.2x00a0;This test method is also useful as a surrogate for other test methods used to measure elasticity in asphalt binders such as Test Method D5801 (Toughness and Tenacity), Test Method D6084 (Elastic Recovery), and Test Method D7175 (DSR phase angle). 1.1x00a0;This test method covers the determination of percent recovery and non-recoverable creep compliance of asphalt binders by means of Multiple Stress Creep and Recovery (MSCR) testing. The MSCR test is conducted using the Dynamic Shear Rheometer (DSR) at a specified temperature. 1.2x00a0;This standard is appropriate for unaged material, material aged in accordance with Test Method D2872 (RTFO), material aged in accordance with Practice D6521 (PAV), and material aged in accordance with both Test Method D2872 and Practice D6521. Note 1:x00a0;The majority of development work on this test method was performed on material aged in accordance with Test Method D2872 (RTFO). 1.3x00a0;The percent recovery is intended to provide a means to determine the presence of elastic response and stress dependence of polymer modified and unmodified asphalt binders. 1.4x00a0;The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：91.100.50 CCS：发布：2015 实施：

AASHTO T 315-2008 用动态剪切流变仪测量沥青胶泥流变特性的标准方法(DSR)
简介：
信息：ICS： CCS：发布：2008-01-01 实施：

GOST R 57950-2017 塑料. 动态力学性能的测定. 第2部分: 用平行板振荡流变仪测量复合剪切粘度
简介：
信息：ICS：83.080.01 CCS：发布：2017-00-00 实施：2018-06-01

ASTM D6601-12 橡胶性能的标准试验方法&x2014；使用无转子剪切流变仪测量固化和固化后动态特性
简介：
信息：ICS：83.060 CCS：发布：2012-12-01 实施：

ASTM D7175-2008 用动态剪切流变仪测定沥青粘结剂流变特性的标准试验方法
简介：The test temperature for this test is related to the temperature experienced by the pavement in the geographical area for which the asphalt binder is intended to be used. The complex shear modulus is an indicator of the stiffness or resistance of asphalt binder to deformation under load. The complex shear modulus and the phase angle define the resistance to shear deformation of the asphalt binder in the linear viscoelastic region. The complex modulus and the phase angle are used to calculate performance-related criteria in accordance with Specification D 6373 or AASHTO Standard M320.1.1 This test method covers the determination of the dynamic shear modulus and phase angle of asphalt binders when tested in dynamic (oscillatory) shear using parallel plate geometry. It is applicable to asphalt binders having dynamic shear modulus values in the range from 100 Pa to 10 MPa. This range in modulus is typically obtained between 4 and 88x00B0;C at 10 rad/s. This test method is intended for determining the linear viscoelastic properties of asphalt binders as required for specification testing and is not intended as a comprehensive procedure for the full characterization of the viscoelastic properties of asphalt binders. 1.2 This standard is appropriate for unaged materials, material aged in accordance with Test Method D 2872, material aged in accordance with Practice D 6521, or material aged in accordance with both Test Method D 2872 and Practice D 6521. This procedure is limited to asphalt binders that contain particles with largest dimension less than 250 x03BC;m. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：93.080.20 (Road construction materials) CCS：E43 发布：2008 实施：

KS M ISO 6721-10-2016(2021) 塑料动态机械性能的测定第10部分:用平行板振荡流变仪测定复合剪切粘度
简介：
信息：ICS：83.080.01 CCS：发布：2016-12-28 实施：

NF T66-074-2012 沥青和沥青粘合剂.复合剪切模量和相位角的测定.动态剪切流变仪(DSR)
简介：
信息：ICS：75.140;91.100.50 CCS：Q27;E43 发布：2012-08-01 实施：2012-08-18

ASTM D7175-07 使用动态剪切流变仪测定沥青粘合剂的流变性能的标准测试方法
简介：
信息：ICS：93.080.20 CCS：发布：2007-12-01 实施：

ASTM D7605-11(2016) 热塑性弹性体的标准试验方法&x2014；用无转子剪切流变仪测量聚合物熔体流变特性和凝固动态特性
简介：
信息：ICS：83.100 CCS：发布：2016-11-01 实施：

DIN EN 14770-2012 沥青和沥青粘合剂.复合剪切模量和相位角的测定.动态剪切流变仪(DSR).德文版本EN 14770-2012
简介：
信息：ICS：75.140;91.100.50 CCS：E43 发布：2012-08 实施：

AASHTO TP 70-2007 用动态剪切流变仪测试的沥青粘合剂(MSCR)的标准试验方法
简介：This practice covers the identification of elastomeric response of modified asphalt binders bymeans of percent recovery obtained in the Multiple Stress Creep Recovery (MSCR) test. TheMSCR test is conducted using the Dynamic Shear Rheometer (DSR) at th
信息：ICS：43.020 CCS：R00 发布：2007-01-01 实施：

ASTM D8059-16 橡胶化合物的标准试验方法&x2014；使用密封腔无转子剪切流变仪测量未硫化动态应变软化（佩恩效应）
简介：
信息：ICS：83.060 CCS：发布：2016-07-01 实施：

BS EN 14770-2012 沥青和沥青粘合剂.复合剪切模量和相位角的测定.动态剪切流变仪(DSR)
简介：
信息：ICS：75.140;91.100.50 CCS：E43 发布：2012-05-31 实施：2012-05-31

ASTM D7175-2007 动态剪切流变仪测定沥青粘结剂流变特性的标准试验方法
简介：The test temperature for this test is related to the temperature experienced by the pavement in the geographical area for which the asphalt binder is intended to be used. The complex shear modulus is an indicator of the stiffness or resistance of asphalt binder to deformation under load. The complex shear modulus and the phase angle define the resistance to shear deformation of the asphalt binder in the linear viscoelastic region. The complex modulus and the phase angle are used to calculate performance-related criteria in accordance with Specification D 6373 or AASHTO Standard M320.
信息：ICS：93.080.20 (Road construction materials) CCS：发布：2007 实施：

PNST 88-2016 一般用途汽车道路. 石油基沥青粘合剂. 采用动态剪切流变仪 (DSR) 测定多剪切应力 (MSCR) 冲击恢复特性的方法
简介：
信息：ICS：93.080.20 CCS：发布：2016 实施：2016-06-01

BS EN 14770-2012 (BS 2000-536-2012) 沥青和沥青粘合剂.复合剪切模量和相位角的测定.动态剪切流变仪(DSR)
简介：
信息：ICS： CCS：发布：2012-01-01 实施：2012-01-01

NF T66-074-2006 沥青和沥青粘合剂.复合剪切模量和相位角的测定.动态剪切流变仪(DSR)
简介：
信息：ICS：75.140;91.100.50 CCS：Q27 发布：2006-03-01 实施：2006-03-05

PNST 87-2016 一般用途汽车道路. 道路用粘性石油沥青. 使用动态剪切流变仪 (DSR) 测定性能的方法
简介：
信息：ICS：93.080.20 CCS：发布：2016 实施：2016-06-01

ASTM D7605-11 热塑性弹性体的标准试验方法使用无转子剪切流变仪测量聚合物熔体流变特性和凝固动态特性
简介：
信息：ICS：83.100 CCS：发布：2011-11-01 实施：

DIN EN 14770-2006 沥青和沥青粘合剂.复合剪切模量和相位角的测定.动态剪切流变仪(DSR)
简介：This European standard covers a number of methods using a dynamic shear rheometer (DSR) capable of measuring the rheological properties of bitumen and bituminous binders. The procedure involves determining the complex shear modulus and phase angle of binders over a range of test frequencies and test temperatures when tested in oscillatory shear. From the test, the norm of the complex shear modulus, IG; I, and its phase angle, d, at a given temperature and frequency can be calculated, as well as their components G', G'', J' and J''. This method is applicable to unaged, aged and recovered bituminous binders, cut backs and bituminous binders recovered from emulsions. It is not applicable where the rheometer cannot control both plates at the test temperature. This method is also applicable to modified binders.
信息：ICS：75.140;91.100.50 CCS：E43 发布：2006-01 实施：

PNST 89-2016 一般用途汽车道路. 石油基沥青粘合剂. 使用动态剪切流变仪 (DSR) 测定低温性能的方法
简介：
信息：ICS：93.080.20 CCS：E43 发布：2016 实施：2016-06-01

ASTM D7654/D7654M-10 用动态剪切流变仪测量的屋面沥青的标准规范
简介：
信息：ICS：91.100.50 CCS：发布：2010-08-01 实施：

ASTM D7175-05 使用动态剪切流变仪测定沥青粘合剂的流变性能的标准测试方法
简介：
信息：ICS： CCS：发布：2005-09-15 实施：

PNST 89-2016 一般用途汽车道路. 石油基沥青粘合剂. 使用动态剪切流变仪 (DSR) 测定低温性能的方法
简介：
信息：ICS：93.080.20 CCS：发布：2016 实施：2016-06-01

ASTM D7405-10a 使用动态剪切流变仪测定沥青粘合剂多重应力蠕变和恢复（MSCR）的标准试验方法
简介：
信息：ICS：91.100.50 CCS：发布：2010-06-01 实施：

ASTM D7175-05e1 使用动态剪切流变仪测定沥青粘合剂的流变性能的标准测试方法
简介：
信息：ICS：93.080.20 CCS：发布：2005-09-15 实施：

PNST 87-2016 一般用途汽车道路. 道路用粘性石油沥青. 使用动态剪切流变仪 (DSR) 测定性能的方法
简介：
信息：ICS：93.080.20 CCS：E43 发布：2016 实施：2016-06-01

ASTM D7605-10 热塑性弹性体的标准试验方法使用无转子剪切流变仪测量聚合物熔体流变特性和凝固动态特性
简介：
信息：ICS：83.100 CCS：发布：2010-02-01 实施：

ASTM D7175-2005 用动态剪切流变仪测定沥青粘结剂流变特性的标准试验方法
简介：1.1 This test method covers the determination of the dynamic shear modulus and phase angle of asphalt binders when tested in dynamic (oscillatory) shear using parallel plate geometry. It is applicable to asphalt binders having dynamic shear modulus values in the range from 100 Pa to 10 MPa. This range in modulus is typically obtained between 4 and 88C at 10 rad/s. This test method is intended for determining the linear viscoelastic properties of asphalt binders as required for specification testing and is not intended as a comprehensive procedure for the full characterization of the viscoelastic properties of asphalt binders.1.2 This standard is appropriate for unaged materials, material aged in accordance with Test Method D 2872, material aged in accordance with Practice D 6521, or material aged in accordance with both Test Method D 2872 and Practice D 6521.1.3 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS： CCS：E43 发布：2005 实施：

PNST 88-2016 一般用途汽车道路. 石油基沥青粘合剂. 采用动态剪切流变仪 (DSR) 测定多剪切应力 (MSCR) 冲击恢复特性的方法
简介：
信息：ICS：93.080.20 CCS：E43 发布：2016 实施：2016-06-01

ASTM D7405-10 使用动态剪切流变仪测定沥青粘合剂多重应力蠕变和恢复（MSCR）的标准试验方法
简介：
信息：ICS：91.100.50 CCS：发布：2010-01-01 实施：

ASTM D7175-2005e1 用动态剪切流变仪测定沥青粘结剂流变特性的标准试验方法
简介：The test temperature for this test is related to the temperature experienced by the pavement in the geographical area for which the asphalt binder is intended to be used. The complex shear modulus is an indicator of the stiffness or resistance of asphalt binder to deformation under load. The complex shear modulus and the phase angle define the resistance to shear deformation of the asphalt binder in the linear viscoelastic region. The complex modulus and the phase angle are used to calculate performance-related criteria in accordance with Specification D 6373.1.1 This test method covers the determination of the dynamic shear modulus and phase angle of asphalt binders when tested in dynamic (oscillatory) shear using parallel plate geometry. It is applicable to asphalt binders having dynamic shear modulus values in the range from 100 Pa to 10 MPa. This range in modulus is typically obtained between 4 and 88C at 10 rad/s. This test method is intended for determining the linear viscoelastic properties of asphalt binders as required for specification testing and is not intended as a comprehensive procedure for the full characterization of the viscoelastic properties of asphalt binders.1.2 This standard is appropriate for unaged materials, material aged in accordance with Test Method D 2872, material aged in accordance with Practice D 6521, or material aged in accordance with both Test Method D 2872 and Practice D 6521.1.3 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：93.080.20 (Road construction materials) CCS：E43 发布：2005 实施：