铸件规格检测标准铸件规格-中析研究所检测

(CMA)

(CNAS)

(ISO)

(高新技术企业)

铸件规格相关标准参考信息

ASTM F1199-2021 铸件 (所有温度和压力) 和焊接管线过滤器 (最大值150 psig和150 ℉) 的标准规格
简介：1.1?This specification covers all cast strainers and welded strainers in services up to 150 psig and 150��F (1 MPa and 65��C). For welded strainers used in services above 150 psig and 150��F, see Specification F1200. 1.2?This standard provides the minimum requirements for the d
信息：ICS： CCS：Q81 发布：2021 实施：

ASTM A781/A781M-2016 一般工业用通用要求的钢和合金铸件的标准规格
简介：1.1x00a0;This specification covers a group of requirements that are mandatory requirements of the following steel casting specifications issued by ASTM. If the product specification specifies different requirements, the product specification shall prevail. ASTM Designation 8201; Title of Specification A27/A27M Steel Castings, Carbon, for General Application A128/A128M Steel Castings, Austenitic Manganese A148/A148M Steel Castings, High Strength, for Structural Purposes A297/A297M Steel Castings, Iron-Chromium and Iron-Chromium-Nickel, Heat Resistant for General Application A447/A447M Steel Castings, Chromium-Nickel-Iron Alloy (25-12 Class), for High-Temperature Service A494/A494M Castings, Nickel and Nickel Alloy A560/A560M Castings, Chromium-Nickel Alloy A743/A743M Castings, Iron-Chromium, Iron-Chromium-Nickel, Corrosion Resistant, for General Application A744/A744M Castings, Iron-Chromium-Nickel, Corrosion Resistant, for Severe Service A747/A747M Steel Castings, Stainless, Precipitation Hardening
信息：ICS：77.140.80 CCS：J31 发布：2016 实施：

ASTM A216/A216M-2014 高温设备用适合于熔焊的碳钢铸件标准规格
简介：1.1x00a0;This specification2 covers carbon steel castings for valves, flanges, fittings, or other pressure-containing parts for high-temperature service and of quality suitable for assembly with other castings or wrought-steel parts by fusion welding. 1.2x00a0;Three grades, WCA, WCB, and WCC, are covered in this specification. Selection will depend upon design and service conditions, mechanical properties, and the high temperature characteristics. 1.3x00a0;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
信息：ICS：77.140.80 (Iron and steel castings) CCS：发布：2014 实施：

ASTM A995/A995M-2018 承压部件用奥氏体-奥氏铬铁(双炼)不锈钢铸件的标准规格
简介：1.1x00a0;This specification covers austenitic-ferritic (duplex) stainless steel castings for valves, flanges, fittings, and other pressure-containing parts. 1.2x00a0;The duplex stainless steels offer a combination of enhanced mechanical properties and corrosion resistance when properly balanced in composition and properly heat treated. Ferrite levels are not specified, but these grades will develop a range of approximately 30 to 608201;% ferrite with the balance austenite. It is the responsibility of the purchaser to determine which grade shall be furnished depending on design and service conditions, mechanical properties, and corrosion-resistant characteristics. Note 1:x00a0;Because of the possibility of precipitation of embrittling phases, the grades included in this specification are not recommended for service at temperatures above 6008201;x00b0;F [3158201;x00b0;C]. 1.3x00a0;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.4x00a0;This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
信息：ICS：77.140.80 CCS：J31 发布：2018 实施：

ASTM B62-15 组成青铜或盎司金属铸件的标准规格
简介：
信息：ICS：77.150.30 CCS：发布：2015-05-01 实施：

ASTM A985/A985M-2014 承压部件的钢熔模铸件通用要求的标准规格
简介：1.1x00a0;This specification covers a group of common requirements that are mandatory for steel castings produced by the investment casting process for pressure-containing parts under each of the following ASTM Specifications: x00a0; Title of Specification ASTM Designation x00a0; x00a0; x00a0; Steel Castings, Carbon, Suitable for Fusion Welding, A216/A216M x00a0; for High-Temperature Service x00a0; Steel Castings, Martensitic Stainless and Alloy, for A217/A217M x00a0; Pressure-Containing Parts, Suitable for High- x00a0; x00a0; Temperature Service x00a0; Castings, Austenitic, Austenitic-Ferritic (Duplex), A351/A351M x00a0; for Pressure-Containing Parts x00a0; Steel Castings, Ferritic and Martensitic, for Pressure-
信息：ICS：49.025.10 CCS：发布：2014 实施：

ASTM B62-17 组成青铜或盎司金属铸件的标准规格
简介：
信息：ICS：77.150.30 CCS：发布：2017-04-01 实施：

ASTM A351/A351M-2015 承压部件的奥氏体铸件的标准规格
简介：1.1x00a0;This specification2 covers austenitic steel castings for valves, flanges, fittings, and other pressure-containing parts (Note 1). Note 1:x00a0;Carbon steel castings for pressure-containing parts are covered by Specification A216/A216M, low-alloy steel castings by Specification A217/A217M, and duplex stainless steel castings by Specification A995/A995M. 1.2x00a0;A number of grades of austenitic steel castings are included in this specification. Since these grades possess varying degrees of suitability for service at high temperatures or in corrosive environments, it is the responsibility of the purchaser to determine which grade shall be furnished. Selection will depend on design and service conditions, mechanical properties, and high-temperature or corrosion-resistant characteristics, or both. 1.2.1x00a0;Because of thermal instability, Grades CE20N, CF3A, CF3MA, and CF8A are not recommended for service at temperatures above 800x00b0;F [425x00b0;C]. 1.3x00a0;Supplementary requirements of an optional nature are provided for use at the option of the purchaser. The Supplementary requirements shall apply only when specified individually by the purchaser in the purchase order or contract. 1.4x00a0;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4.1x00a0;This specification is expressed in both inch-pound units and in SI units; however, unless the purchase order or contract specifies the applicable M specification designation (SI units), the inch-pound units shall apply. Within the text, the SI units are shown in brackets or parentheses.
信息：ICS：77.140.80 CCS：H43 发布：2015 实施：

ASTM B763/B763M-2014 阀门应用铜合金砂铸件标准规格
简介：1.1x00a0;This specification establishes requirements for copper alloy sand castings for valve applications. Nominal compositions of the alloys defined by this specification are shown in Table 1.2 TABLE 1 Nominal Compositions Classification Copper Alloy UNS No. Commercial Designation Copper Tin Lead Zinc Nickel Iron Alumi- num Man- ganese Sili- con Bismuth Sele- nium Leaded red brass C83450 x00a0;......
信息：ICS：77.150.30 (Copper products) CCS：J16 发布：2014 实施：

ASTM A494/A494M-2017 镍和镍合金铸件的标准规格
简介：1.1x00a0;This specification covers nickel, nickel-copper, nickel-copper-silicon, nickel-molybdenum, nickel-chromium, and nickel-molybdenum-chromium alloy castings for corrosion-resistant service. 1.2x00a0;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.
信息：ICS：77.150.40 CCS：H43;J31 发布：2017 实施：

ASTM A148/A148M-2015 建筑结构用高强度钢铸件的标准规格
简介：1.1x00a0;This specification covers carbon steel, alloy steel, and martensitic stainless steel castings that are to be subjected to higher mechanical stresses than those covered in Specification A27/A27M. 1.2x00a0;Several grades of steel castings are covered, having the chemical composition and mechanical properties prescribed in Tables 1 and 2. 1.3x00a0;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3.1x00a0;Within the text, the SI units are shown in brackets.
信息：ICS：77.140.80 CCS：J31;H48;H41 发布：2015 实施：

ASTM F1108-2014 外科植入物用钛-6铝-4钒合金铸件的标准规格 (UNS R56406)
简介：1.1x00a0;This specification covers the chemical, mechanical, and metallurgical requirements for cast titanium-6aluminum-4vanadium alloy (UNS R56406). 1.2x00a0;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.
信息：ICS：11.040.40 CCS：发布：2014 实施：

ASTM B240-2017 铸造和压模铸件用铸锭结构中锌和锌铝(ZA)合金的标准规格
简介：1.1x00a0;This specification covers commercial zinc and zinc-aluminum (ZA) alloys in ingot form for remelting for the manufacture of pressure die castings, foundry castings and continuous cast bar stock as designated and specified in Table 1. Seven alloy compositions are specified, designated as follows: Common Traditional ASTMA UNSA x00a0; x00a0; x00a0; x00a0; Alloy 3 Zamak 3 AG 40A Z33524 Alloy 7 Zamak 7 AG 40B Z33526 Alloy 5 Zamak 5 AC 41A Z35532 Alloy 2 Zamak 2 AC 43A Z35544 ZA-8 ZA-8x2007; ... Z35637 ZA-12 ZA-12
信息：ICS：77.150.60 CCS：H62 发布：2017 实施：

ASTM B66-2015 蒸汽机车易损件用青铜铸件的标准规格
简介：1.1x00a0;This specification establishes requirements for bronze castings for steam locomotive wearing parts. The following Copper Alloy UNS Nos. are specified: C93200, C93400, C93600, C93700, C93800, C94300, C94400, C94500, and C95400.2 Note 1:x00a0;Historically, the alloys in this specification have been used in the applications listed in the Appendix. Actual practice may vary according to locomotive type and service. 1.2x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：77.150.30 CCS：发布：2015 实施：

ASTM B26/B26M-2014e1 铝合金砂模铸件的标准规格
简介：1.1x00a0;This specification2 covers aluminum-alloy sand castings designated as shown in Table 1. (A)x00a0;Contains silver 0.40x2013;1.08201;%.(B)x00a0;If iron exceeds 0.458201;%, manganese content shall not be less than one half of the iron content.(C)x00a0;Contains beryllium 0.003x2013;0.0078201;%, boron 0.0058201;% max.(D)x00a0;710.0 formerly A712.0, 712.0 formerly D712.0, 851.0 formerly A850.0, 852.0 formerly B850.0.(E)x00a0;ASTM alloy designations are recorded in Practice B275.(F)x00a0;x201c;Othersx201d; includes listed elements for which no specific limit is shown as well as unlisted metallic elements. The producer may analyze samples for trace elements not specified in the specification. However, such analysis is not required and may not cover all metallic x201c;Othersx201d; elements. Should any analysis by the producer or the purchaser establish that an x201c;Othersx201d; element exceeds the limit of x201c;Eachx201d; or that the aggregate of several x201c;Othersx201d; elements exceeds the limit of x201c;Total,x201d; the material shall be considered nonconforming.(G)x00a0;Other Elementsx2013;Total shall be the sum of unspecified metallic elements 0.0108201;% or more, rounded to the second decimal before determining the sum. 1.2x00a0;This specification is for aluminum-alloy sand castings used in general purpose applications. It may not address the mechanical properties, integrity testing, and verification required for highly loaded or safety critical applications. 1.3x00a0;Alloy and temper designations are in accordance with ANSI H35.1/H35.1M. Unified Numbering System alloy designations are in accordance with Practice E527. 1.4x00a0;Unless the order specifies the x201c;Mx201d; specification designation, the material shall be furnished to the inch-pound units. 1.5x00a0;For acceptance criteria for inclusion of new aluminum and aluminum alloys and their properties in this specification, see Annex A1 and Annex A2. 1.6x00a0;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact......
信息：ICS：77.150.10 CCS：发布：2014 实施：

ASTM A703/A703M-2017a 承压部件的钢铸件通用要求的标准规格
简介：1.1x00a0;This specification2 covers a group of common requirements that, unless otherwise specified in an individual specification, shall apply to steel castings for pressure-containing parts under each of the following ASTM specifications: x00a0; Title of Specification ASTM Designation x00a0; x00a0; x00a0; Steel Castings, Carbon, Suitable for Fusion Welding, A216/A216M x00a0; for High-Temperature Service x00a0; Steel Castings, Martensitic Stainless and Alloy, for A217/A217M x00a0; Pressure-Containing Parts, Suitable for High- x00a0; x00a0; Temperature Service x00a0; Castings, Austenitic, Austenitic-Ferritic (Duplex), A351/A351M x00a0; Pressure-Containing Parts x00a0; Steel Castings, Ferritic and Martensitic, for Pressure-
信息：ICS：77.140.80 CCS：J31 发布：2017 实施：

ASTM A148/A148M-2015a 结构用高强度钢铸件的标准规格
简介：1.1x00a0;This specification covers carbon steel, alloy steel, and martensitic stainless steel castings that are to be subjected to higher mechanical stresses than those covered in Specification A27/A27M. 1.2x00a0;Several grades of steel castings are covered, having the chemical composition and mechanical properties prescribed in Tables 1 and 2. 1.3x00a0;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3.1x00a0;Within the text, the SI units are shown in brackets.
信息：ICS：77.140.80 CCS：H41 发布：2015 实施：

ASTM A487/A487M-2014e1 受压钢铸件的标准规格
简介：1.1x00a0;This specification2 covers low-alloy steels and martensitic stainless steels in the normalized and tempered, or quenched and tempered, condition suitable for pressure-containing parts. The weldability of the classes in this specification varies from readily weldable to weldable only with adequate precautions, and the weldability of each class should be considered prior to assembly by fusion welding. 1.2x00a0;Selection will depend on design, mechanical, and service conditions. Users should note that hardenability of some of the grades mentioned may restrict the maximum size at which the required mechanical properties are obtained. 1.3x00a0;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3.1x00a0;Within the text, the SI units are shown in brackets. 1.4x00a0;This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
信息：ICS：77.140.80 CCS：J31 发布：2014 实施：

ASTM B969/B969M-2017 用模压铸造, 触变铸造和流变铸造半固体铸件法生产的铝合金铸件的标准规格
简介：1.1x00a0;This specification covers aluminum-alloy castings, produced by the thixocast, rheocast, semi-solid, and squeeze casting processes shown in Table 1. (A)x00a0;When single units are shown, they indicate the maximum amounts permitted.(B)x00a0;Analysis shall be made for the elements for which limits are shown in this table.(C)x00a0;The following applies to all specified limits in this table: For purposes of determining conformance to these limits, an observed value or a calculated value obtained from analysis shall be rounded to the nearest unit in the last right-hand place of figures used in expressing the specified limit in accordance with the rounding-off method of Practice E29.(D)x00a0;In case of discrepancy between the values listed in Table 1 and those listed in the x201c;x009c;Designations and Composition Limits for Aluminum Alloys in the Form of Castings and Ingot (known as the x201c;x009c;Pink Sheetsx201d;)x201d;x0080;x009c;, the composition limits registered with the Aluminum Association and published in the x201c;x009c;Pink Sheetsx201d; shall be considered the controlling composition.(E)x00a0;x201c;Othersx201d; includes listed elements for which no specific limit is shown as well as unlisted metallic elements. The producer may analyze samples for trace elements not specified in the specification. However, such analysis is not required and may not cover all metallic x201c;Othersx201d; elements. Should any analysis by the producer or the purchaser establish that an x201c;Othersx201d; element exceeds the limit of x201c;Eachx201d; or that the aggregate of several x201c;Othersx201d; elements exceeds the limit of x201c;Total,x201d; the material shall be considered nonconforming.(F)x00a0;Other Elementsx2014;Total shall be the sum of unspecified metallic elements 0.0108201;% or more, rounded to the second decimal before determining the sum.(G)x00a0;If iron exceeds 0.45, manganese content shall not be less than one-half iron content.(H)x00a0;The Aluminum Association ruling on the number of decimal places to which Mg percent is expressed is exempted for some long standing alloys. See A2.2.6.(I)x00a0;For a cross reference of current and former alloy designations see the Aluminum Associationx2019;x0080;x0099;s x201c;Designations and Chemical Composition Limits for Aluminum Alloys in the Form of Castings and Ingot (The Pink Sheets)x201d;.
信息：ICS：77.150.10 CCS：H61 发布：2017 实施：

ASTM A757/A757M-2015 低温用承压及其他应用使用铁素体和马氏体钢铸件的标准规格
简介：1.1x00a0;This specification covers carbon and alloy steel castings for pressure-containing and other applications intended primarily for petroleum and gas pipelines in areas subject to low-ambient temperatures. Castings shall be heat treated by normalizing and tempering or liquid quenching and tempering. All classes are weldable under proper conditions. Hardenability of some grades may limit usable section size. 1.2x00a0;The values stated in either inch-pound units or SI units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.2.1x00a0;Unless the order specifies an x201c;Mx201d; designation, the material shall be furnished to inch-pound units. 1.3x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：77.140.80 CCS：发布：2015 实施：

ASTM B686/B686M-2014 高强度铝合金铸件的标准规格
简介：1.1x00a0;This specification covers aluminum-alloy high-strength castings designated as shown in Table 1. (A)x00a0;x201c;Othersx201d; includes listed elements for which no specific limit is shown as well as unlisted metallic elements. The producer may analyze samples for trace elements not specified in the specification. However, such analysis is not required and may not cover all metallic x201c;Othersx201d; elements. Should any analysis by the producer or the purchaser establish that an x201c;Othersx201d; element exceeds the limit of x201c;Eachx201d; or that the aggregate of several x201c;Othersx201d; elements exceeds the limit of x201c;Total,x201d; the material shall be considered nonconforming.(B)x00a0;Other Elementsx2014;Total shall be the sum of unspecified metallic elements 0.0108201;% or more, rounded to the second decimal before determining the sum.(C)x00a0;Silver 0.40 to 1.08201;%.(D)x00a0;Beryllium 0.04x2013;0.07. 1.2x00a0;Castings covered by this specification are intended for use in airframe, missile, and other critical applications where high strength, ductility, and sound castings are required. 1.3x00a0;Alloy and temper designations are in accordance with ANSI H35.1/H35.18201;(M). The equivalent Unified Numbering System alloy designations are in accordance with Practice E527. 1.4x00a0;Unless the order specifies the x201c;Mx201d; specification designation, the material shall be furnished to the inch-pound units. 1.5x00a0;For acceptance criteria for inclusion of new aluminum and aluminum alloys and their properties in this specification, see Annex A1 and Annex A2. 1.6x00a0;Unitsx2014;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.7x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regular limitations prior to use.
信息：ICS：77.150.10 CCS：发布：2014 实施：

ASTM A352/A352M-2017 适用于低温服务的承压部件的钢铸件, 铁素体和马氏体的标准规格
简介：1.1x00a0;This specification2 covers steel castings for valves, flanges, fittings, and other pressure-containing parts intended primarily for low-temperature service. 1.2x00a0;Several grades of ferritic steels and one grade of martensitic steel are covered. Selection of analysis will depend on design and service conditions (Note 1). The temperature shown is the lowest temperature at which the material ordinarily is required to meet the impact requirements of this specification (see Supplementary Requirement S22, Impact Test Temperatures). Users should note that hardenability of some of the grades mentioned may restrict the maximum size at which the required mechanical properties are obtainable (see Appendix X1). Grade Usual Minimum Testing Temperatures, x00b0;F [x00b0;C] LCA x2212;25 [x2013;32] LCB x2212;50 [x2013;46] LCC x2212;50 [x2013;46] LC1 x2212;75 [x2013;59] LC2 x2212;100 [x2013;73] LC2x2013;1 x2212;100 [x2013;73] LC3 x2212;150 [x2013;101] LC4 x2212;175 [x2013;115] LC9 x2212;320 [x2013;196] CA6NM x2212;100 [x2212;73]
信息：ICS：77.140.80 CCS：J31 发布：2017 实施：

ASTM B271/B271M-2015 离心铸造铜基合金铸件的标准规格
简介：1.1x00a0;This specification establishes requirements for centrifugal castings of copper-base alloys having the nominal compositions shown in Table 1. (A)x00a0;Phosphorus 0.13 1.2x00a0;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
信息：ICS：77.150.30 CCS：发布：2015 实施：

ASTM B824-2014 铜合金铸件通用要求的标准规格
简介：14.1x00a0;For the purpose of determining compliance with the specified limits for requirements of the properties listed in the following table, an observed value or a calculated value shall be rounded as indicated in accordance with the rounding method of Practice E29. Property Rounded Limit for Observed or Calculated Value x00a0; Chemical Composition Hardness Electrical Resistivity Electrical Conductivity nearest unit in the last right-hand significance digit used in expressing the limiting value x00a0; x00a0; Tensile Strength nearest ksi (5 MPa) Yield Strength x00a0; x00a0; Elongation nearest 18201;% x00a0; x00a0; Grain Size: x00a0; 8201;Under 0.060 mm nearest multiple of 0.005 mm 8201;0.060 mm and over nearest 0.01 mm 1.1x00a0;This specification establishes general requirements common to ASTM copper alloy casting specifications B22, B61, B62, B66, B67, B148, B176, B271/B271M, B369, B427, B505/B505M, B584, B763/B763M, B770, and B806. These requirements apply to the casting specifications to the extent referenced therein. 1.1.1x00a0;In the event of conflict between this specification and a casting specification, the requirements of the casting specification shall take precedence. 1.2x00a0;The chemical composition and other requirements not included in this specification shall be prescribed in the casting product specifications. 1.3x00a0;Unitsx2014;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions......
信息：ICS：6800; 77.150.30 (Copper products) CCS：H62 发布：2014 实施：

ASTM A743/A743M-2017 通用铁铬和铁铬镍耐腐蚀铸件的标准规格
简介：1.1x00a0;This specification covers iron-chromium and iron-chromium-nickel alloy castings for general corrosion-resistant application. The grades covered by this specification represent types of alloy castings suitable for broad ranges of application which are intended for a wide variety of corrosion environments. Note 1:x00a0;For alloy castings for severe corrosion-resistant service, reference should be made to Specification A744/A744M. For general heat-resistant alloy castings, reference should be made to Specification A297/A297M. For nickel alloy castings for corrosion-resistant service, reference should be made to Specification A494/A494M. 1.2x00a0;The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. Inch-pound units are applicable for material ordered to Specification A743 and SI units for material ordered to Specification A743M. 1.3x00a0;This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
信息：ICS：77.140.80 CCS：J31 发布：2017 实施：

ASTM A957/A957M-2015 一般工业用途的通用要求钢及合金熔模铸件的标准规格
简介：1.1x00a0;This specification covers a group of requirements that are mandatory for castings produced by the investment casting process to meet the metallurgical requirements of the following steel casting specifications issued by ASTM. ASTM Designation Title of Specification A27/A27M Steel Castings, Carbon, for General Application A128/A128M Steel Castings, Austenitic Manganese A148/A148M Steel Castings, High-Strength, for Structural Purposes A297/A297M Steel Castings, Iron-Chromium and Iron-Chromium-Nickel, Heat-Resistant, for General Application A447/A447M Steel Castings, Chromium-Nickel-Iron Alloy (25-12 Class), for High-Temperature Service A494/A494M Castings, Nickel and Nickel Alloy A560/A560M Castings, Chromium-Nickel Alloy A732/A732M Castings, Investment, Carbon and Low Alloy Steel for General Application, and Cobalt Alloy for High Strength at Elevated Temperatures A743/A743M Castings, Iron-Chromium, Iron-Chromium-Nickel, Corrosion-Resistant, for General Application A744/A744M Castings, Iron-Chromium-Nickel, Corrosion Resistant, for ......
信息：ICS：77.100 CCS：发布：2015 实施：

ASTM A351/A351M-2014 承压件用奥氏体铸件标准规格
简介：1.1x00a0;This specification2 covers austenitic steel castings for valves, flanges, fittings, and other pressure-containing parts (Note 1). Note 1x2014;Carbon steel castings for pressure-containing parts are covered by Specification A216/A216M, low-alloy steel castings by Specification A217/A217M, and duplex stainless steel castings by Specification A995/A995M. 1.2x00a0;A number of grades of austenitic steel castings are included in this specification. Since these grades possess varying degrees of suitability for service at high temperatures or in corrosive environments, it is the responsibility of the purchaser to determine which grade shall be furnished. Selection will depend on design and service conditions, mechanical properties, and high-temperature or corrosion-resistant characteristics, or both. 1.2.1x00a0;Because of thermal instability, Grades CE20N, CF3A, CF3MA, and CF8A are not recommended for service at temperatures above 800x00b0;F [425x00b0;C]. 1.3x00a0;Supplementary requirements of an optional nature are provided for use at the option of the purchaser. The Supplementary requirements shall apply only when specified individually by the purchaser in the purchase order or contract. 1.4x00a0;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4.1x00a0;This specification is expressed in both inch-pound units and in SI units; however, unless the purchase order or contract specifies the applicable M specification designation (SI units), the inch-pound units shall apply. Within the text, the SI units are shown in brackets or parentheses.
信息：ICS：77.140.80 (Iron and steel castings) CCS：发布：2014 实施：

ASTM A494/A494M-2017a 镍和镍合金铸件的标准规格
简介：1.1x00a0;This specification covers nickel, nickel-copper, nickel-copper-silicon, nickel-molybdenum, nickel-chromium, and nickel-molybdenum-chromium alloy castings for corrosion-resistant service. 1.2x00a0;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.3x00a0;This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
信息：ICS：77.150.40 CCS：H62 发布：2017 实施：

ASTM A958/A958M-2015 带有拉伸要求和与标准锻造等级相似的化学要求的碳和合金钢铸件的标准规格
简介：1.1x00a0;This specification covers carbon and low-alloy steel castings having chemical analyses similar to that of the standard wrought grades. 1.2x00a0;Several classes are covered and are designated by chemical composition as shown in Table 1. 1.3x00a0;Options for tensile properties are shown in Tables 2 and 3. (A)x00a0;x201c;Xx201d; denotes that the properties may be achieved by at least one of the heat treatments referenced in 5. The effect of section thickness should be considered in making grade selections. The heat treatment requirements do not imply that all section thicknesses will be through hardened.(B)x00a0;These grades significantly exceed the minimum strength levels; therefore, they may be unsuitable for use due to weldability, and machinability issues. 1.4x00a0;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4.1x00a0;Within the text, the SI units are shown in brackets.
信息：ICS：77.100 CCS：发布：2015 实施：

ASTM B108/B108M-2014 铝合金永久型模铸件的标准规格
简介：1.1x00a0;This specification2 covers aluminum-alloy permanent mold castings designated as shown in Table 1. (A)x00a0;When single units are shown, these indicate the maximum amounts permitted.(B)x00a0;Analysis shall be made for the elements for which limits are shown in this table.(C)x00a0;The following applies to all specified limits in this table: For purposes of determining conformance to these limits, an observed value or a calculated value obtained from analysis shall be rounded to the nearest unit in the last right-hand place of figures used in expressing the specified limit in accordance with the rounding method of Practice E29.(D)x00a0;ASTM alloy designations are recorded in Practice B275.(E)x00a0;Others includes listed elements for which no specific limit is shown as well as unlisted metallic elements. The producer may analyze samples for trace elements not specified in the specification. However, such analysis is not required and may not cover all metallic Others elements. Should any analysis by the producer or the purchaser establish that an Others element exceeds the limit of Each or that the aggregate of several Others elements exceeds the limit of Total, the material shall be considered nonconforming.(F) Other Elementsx2014;Total shall be the sum of unspecified metallic elements 0.0108201;% or more, rounded to the second decimal before determining the sum.(G)x00a0;336.0 formerly A332.0, 332.0 formerly F332.0, 513.0 formerly A514.0, 711.0 formerly C712.0, 851.0 formerly A850.0, 852.0 formerly B850.0.(H)x00a0;If the iron content exceeds 0.458201;%, manganese content shall not be less than one half of the iron.(I)x00a0;Beryllium 0.04x2013;0.07.(J)x00a0;Beryllium 0.002 max
信息：ICS：77.150.10 (Aluminium products) CCS：发布：2014 实施：

BS EN ISO 11970-2016 用于钢铸件生产焊接的焊接流程的规格和资格
简介：
信息：ICS：25.160.10;77.140.80 CCS：J33 发布：2016-04-30 实施：2016-04-30

ASTM A957/A957M-2015a 一般工业用通用要求的熔模钢和合金铸件的标准规格
简介：1.1x00a0;This specification covers a group of requirements that are mandatory for castings produced by the investment casting process to meet the metallurgical requirements of the following steel casting specifications issued by ASTM. ASTM Designation Title of Specification A27/A27M Steel Castings, Carbon, for General Application A128/A128M Steel Castings, Austenitic Manganese A148/A148M Steel Castings, High-Strength, for Structural Purposes A297/A297M Steel Castings, Iron-Chromium and Iron-Chromium-Nickel, Heat-Resistant, for General Application A447/A447M Steel Castings, Chromium-Nickel-Iron Alloy (25-12 Class), for High-Temperature Service A494/A494M Castings, Nickel and Nickel Alloy A560/A560M Castings, Chromium-Nickel Alloy A732/A732M Castings, Investment, Carbon and Low Alloy Steel for General Application, and Cobalt Alloy for High Strength at Elevated Temperatures A743/A743M Castings, Iron-Chromium, Iron-Chromium-Nickel, Corrosion-Resistant, for General Application A744/A744M Castings, Iron-Chromium-Nickel, Corrosion Resistant, for ......
信息：ICS：77.100 CCS：发布：2015 实施：

ASTM A703/A703M-2014 承压部件的钢铸件通用要求的标准规格
简介：1.1x00a0;This specification2 covers a group of common requirements that, unless otherwise specified in an individual specification, shall apply to steel castings for pressure-containing parts under each of the following ASTM specifications: x00a0; Title of Specification ASTM Designation x00a0; x00a0; x00a0; Steel Castings, Carbon, Suitable for Fusion Welding, A216/A216M x00a0; for High-Temperature Service x00a0; Steel Castings, Martensitic Stainless and Alloy, for A217/A217M x00a0; Pressure-Containing Parts, Suitable for High- x00a0; x00a0; Temperature Service x00a0; Castings, Austenitic, Austenitic-Ferritic (Duplex), A351/A351M x00a0; Pressure-Containing Parts x00a0; Steel Castings, Ferritic and Martensitic, for Pressure-
信息：ICS：77.140.80 CCS：H43;J31 发布：2014 实施：

ASTM A356/A356M-2016 蒸汽涡轮机用碳素, 低合金, 不锈钢, 厚壁钢铸件的标准规格
简介：1.1x00a0;This specification covers one grade of martensitic stainless steel and several grades of ferritic steel castings for cylinders (shells), valve chests, throttle valves, and other heavy-walled castings for steam turbine applications. 1.2x00a0;Optional supplementary requirements (S1 through S5) shall apply as selected by and specified by the purchaser. 1.3x00a0;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.3.1x00a0;Within the text, the SI units are shown in brackets.
信息：ICS：77.140.80 CCS：H40 发布：2016 实施：

ASTM F1108-14 用于外科植入物的钛-6A铝-4钒合金铸件标准规格（UNS R56406）
简介：
信息：ICS：11.040.40 CCS：发布：2014-11-01 实施：

ASTM B989-2014 薄壁压铸件用锭形高流动性(HF)锌铝合金的标准规格
简介：1.1x00a0;This specification covers a commercial zinc-aluminum alloy in ingot form for remelting for the manufacture of thin wall pressure die castings as designated and specified in Table 1.TABLE 1 Chemical and North American Color Code Requirements Common Name HF AlloyA,B,C UNS to be assigned Color CodeD Red/Brown Element x00a0; Aluminum 4.3x2013;4.7 Magnesium 0.005x2013;0.012 Copper, max 0.035 Iron, max 0.03 Lead, max 0.003 Cadmium, max 0.002 Tin, max 0.001 ZincE Remainder A Zinc alloy ingots for die casting may contain nickel, chromium, silicon, and manganese in amounts of up to 0.01, 0.01, 0.01, and 0.01 %, respectively. No harmful effects have ever been noted due to the presence of these elements in up to these concentrations and, therefore, analyses are not required for these elements.B The last digit of a UNS number differentiates between alloys of similar composition. UNS designations for ingot and casting versions of an alloy were not assigned in the same sequence for alloys.C For purposes of acceptance and rejection, the observed value or cal......
信息：ICS：77.120.10 (Aluminium and aluminium alloys) CCS：发布：2014 实施：

ASTM A351/A351M-2016 承压部件的奥氏体铸件的标准规格
简介：1.1x00a0;This specification2 covers austenitic steel castings for valves, flanges, fittings, and other pressure-containing parts (Note 1). Note 1:x00a0;Carbon steel castings for pressure-containing parts are covered by Specification A216/A216M, low-alloy steel castings by Specification A217/A217M, and duplex stainless steel castings by Specification A995/A995M. 1.2x00a0;A number of grades of austenitic steel castings are included in this specification. Since these grades possess varying degrees of suitability for service at high temperatures or in corrosive environments, it is the responsibility of the purchaser to determine which grade shall be furnished. Selection will depend on design and service conditions, mechanical properties, and high-temperature or corrosion-resistant characteristics, or both. 1.2.1x00a0;Because of thermal instability, Grades CE20N, CF3A, CF3MA, and CF8A are not recommended for service at temperatures above 800x00b0;F [425x00b0;C]. 1.3x00a0;Supplementary requirements of an optional nature are provided for use at the option of the purchaser. The Supplementary requirements shall apply only when specified individually by the purchaser in the purchase order or contract. 1.4x00a0;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4.1x00a0;This specification is expressed in both inch-pound units and in SI units; however, unless the purchase order or contract specifies the applicable M specification designation (SI units), the inch-pound units shall apply. Within the text, the SI units are shown in brackets or parentheses.
信息：ICS：77.140.80 CCS：发布：2016 实施：

ASTM B955/B955M-2014 铝合金离心铸件的标准规格
简介：1.1x00a0;This specification covers aluminum-alloy centrifugal castings designated as shown in Table 1. (A)x00a0;When single units are shown, these indicate the maximum amounts permitted.(B)x00a0;Analysis shall be made for the elements for which limits are shown in this table.(C)x00a0;The following applies to all specified limits in this table: For purposes of determining conformance to these limits, an observed value or a calculated value obtained from analysis shall be rounded to the nearest unit in the last right-hand place of figures used in expressing the specified limit in accordance with the rounding method of Practice E29.(D)x00a0;ASTM alloy designations are defined in ANSI H35.1/H35.1 (M).(E) Others includes listed elements for which no specific limit is shown as well as unlisted metallic elements. The producer may analyze samples for trace elements not specified in the specification. However, such analysis is not required and may not cover all metallic Others elements. Should any analysis by the producer or the purchaser establish that an Others element exceeds the limit of Each or that the aggregate of several Others elements exceeds the limit of Total, the material shall be considered nonconforming.(F) 2Other Elementsx2014;Total shall be the sum of unspecified metallic elements 0.0108201;% or more, rounded to the second decimal before determining the sum.(G)x00a0;If the iron content exceeds 0.458201;%, manganese content shall not be less than one half of the iron. 1.2x00a0;This specification is not intended for aluminum-alloy centrifugal castings used in aerospace applications. 1.3x00a0;Alloy and temper designations are in accordance with ANSI H35.1/H35.1 (M). The equivalent unified numbering system alloy designations are in accordance with Practice E527. 1.4x00a0;Unless the order specifies the x201c;Mx201d; specification designation, the material shall be furnished to the inch-pound units.
信息：ICS：77.150.10 CCS：发布：2014 实施：

ASTM A747/A747M-2016 沉淀硬化不锈钢铸件的标准规格
简介：1.1x00a0;This specification covers iron-chromium-nickel-copper corrosion-resistant steel castings, capable of being strengthened by precipitation hardening heat treatment. 1.2x00a0;These castings may be used in services requiring corrosion resistance and high strengths at temperatures up to 600x00b0;F [315x00b0;C]. They may be machined in the solution-annealed condition and subsequently precipitation hardened to the desired high-strength mechanical properties specified in Table S14.1 with little danger of cracking or distortion. 1.3x00a0;The material is not intended for use in the solution-annealed condition. Note 1:x00a0;If the service environment in which the material is to be used is considered conducive to stress-corrosion cracking, precipitation hardening should be performed at a temperature that will minimize the susceptibility of the material to this type of attack. 1.4x00a0;Supplementary requirements of an optional nature are provided for use at the option of the purchaser. The Supplementary requirements shall apply only when specified individually by the purchaser in the purchase order or contract. 1.5x00a0;This specification is expressed in both inch-pound units and in SI units; however, unless the purchase order or contract specifies the applicable M specification designation (SI units), the inch-pound units shall apply. 1.6x00a0;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.6.1x00a0;Within the text, the SI units are shown in brackets.
信息：ICS：77.140.80 CCS：发布：2016 实施：

ASTM A990/A990M-2014 耐腐用保压零件用特殊控制用铁铬镍和铬合金铸件的标准规格
简介：1.1x00a0;This specification covers iron-nickel-chromium and nickel alloy castings specially processed with restricted melt practices, weldability testing, and nondestructive examination (NDE) requirements. 1.2x00a0;A number of grades of iron-nickel-chromium and nickel alloy castings are included in this specification. Since these grades possess varying degrees of suitability for service in corrosive environments, it is the responsibility of the purchaser to determine which grade shall be furnished. Selection will depend on design and service conditions, mechanical properties, and corrosion-resistant characteristics. 1.3x00a0;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3.1x00a0;This specification is expressed in both inch-pound units and in SI units; however, unless the purchase order or contract specifies the applicable M specification designation (SI units), the inch-pound units shall apply. Within the text, the SI units are shown in brackets or parentheses. 1.4x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：77.120.40 (Nickel, chromium and their alloys) CCS：发布：2014 实施：

ASTM B792-2016 空壳铸件用锭锌合金的标准规格
简介：1.1x00a0;This specification covers commercial zinc alloys in ingot form for remelting for the manufacture of castings from the alloys as specified and designated as shown in Table 1. (A)x00a0;The following applies to all specified limits in this table. For purposes of determining conformance with this specification, the observed or calculated value obtained from analysis shall be rounded off x201c;to the nearest unitx201d; in the last right-hand place of figures used in expressing the specified limit, in accordance with the rounding method of Practice E29.(B)x00a0;UNS designations were established in accordance with Practice E527.(C)x00a0;Refer to Practice B908. (Note: Colors indicated are for North American applications.) 1.2x00a0;Slush casting alloys are used primarily for the manufacture of hollow castings such as lighting fixtures, lamp bases, and small statues. 1.3x00a0;This specification covers two zinc alloys which are specified and designated as follows: UNS ASTM Z34510 Slush Casting Alloy A Z30500 Slush Casting Alloy B 1.4x00a0;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.
信息：ICS：77.150.60 CCS：发布：2016 实施：

ASTM B148-2014 铝青铜砂型铸件标准规格
简介：1.1x00a0;This specification establishes requirements for sand castings produced from copper-base alloys having the alloy numbers,2 commercial designations, and nominal compositions shown in Table 1.TABLE 1 Nominal Compositions Copper Alloy UNS No. Old Designation Commercial Designation Nominal Composition, % Copper Nickel Iron Aluminum Silicon Manganese 8199;8199;C95200 9A Grade A 88.0 . . . 3.0 9.0 . . . . . . 8199;8199;C95300A 9B Grade B
信息：ICS：77.150.10 (Aluminium products) CCS：D42 发布：2014 实施：

ASTM A957/A957M-2014 一般工业用通用要求的熔模钢和合金铸件的标准规格
简介：1.1x00a0;This specification covers a group of requirements that are mandatory for castings produced by the investment casting process to meet the metallurgical requirements of the following steel casting specifications issued by ASTM. ASTM Designation Title of Specification A27/A27M Steel Castings, Carbon, for General Application A128/A128M Steel Castings, Austenitic Manganese A148/A148M Steel Castings, High-Strength, for Structural Purposes A297/A297M Steel Castings, Iron-Chromium and Iron-Chromium-Nickel, Heat-Resistant, for General Application A447/A447M Steel Castings, Chromium-Nickel-Iron Alloy (25-12 Class), for High-Temperature Service A494/A494M Castings, Nickel and Nickel Alloy A560/A560M Castings, Chromium-Nickel Alloy A732/A732M Castings, Investment, Carbon and Low Alloy Steel for General Application, and Cobalt Alloy for High Strength at Elevated Temperatures A743/A743M Castings, Iron-Chromium, Iron-Chromium-Nickel, Corrosion-Resistant, for General Application A744/A744M Castings, Iron-Chromium-Nickel, Corrosion Resistant, for ......
信息：ICS：77.100 CCS：发布：2014 实施：

ASTM A216/A216M-2016 高温设备用适合熔焊的碳素钢铸件的标准规格
简介：1.1x00a0;This specification2 covers carbon steel castings for valves, flanges, fittings, or other pressure-containing parts for high-temperature service and of quality suitable for assembly with other castings or wrought-steel parts by fusion welding. 1.2x00a0;Three grades, WCA, WCB, and WCC, are covered in this specification. Selection will depend upon design and service conditions, mechanical properties, and the high temperature characteristics. 1.3x00a0;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
信息：ICS：77.140.80 CCS：H43 发布：2016 实施：

ASTM B176-2014 铜合金压铸件标准规格
简介：1.1x00a0;This specification establishes the requirements for copper-alloy die castings. The alloys specified are Copper Alloy UNS Nos. C85700, C85800, C86500, C87800, C99700, and C99750.2 1.2x00a0;Unitsx2014;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
信息：ICS：9750 CCS：H62 发布：2014 实施：

ASTM A990/A990M-2014a 耐腐用保压零件用特殊控制阀的铁铬镍和铬合金铸件的标准规格
简介：1.1x00a0;This specification covers iron-nickel-chromium and nickel alloy castings specially processed with restricted melt practices, weldability testing, and nondestructive examination (NDE) requirements. 1.2x00a0;A number of grades of iron-nickel-chromium and nickel alloy castings are included in this specification. Since these grades possess varying degrees of suitability for service in corrosive environments, it is the responsibility of the purchaser to determine which grade shall be furnished. Selection will depend on design and service conditions, mechanical properties, and corrosion-resistant characteristics. 1.3x00a0;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3.1x00a0;This specification is expressed in both inch-pound units and in SI units; however, unless the purchase order or contract specifies the applicable M specification designation (SI units), the inch-pound units shall apply. Within the text, the SI units are shown in brackets or parentheses. 1.4x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：77.120.40 CCS：发布：2014 实施：

ASTM B618/B618M-2014 铝合金熔模铸件的标准规格
简介：1.1x00a0;This specification covers aluminum-alloy investment castings designated as shown in Table 1. (A)x00a0;ASTM alloy designations are in Practice B275.(B)x00a0;x201c;Othersx201d; includes listed elements for which no specific limit is shown as well as unlisted metallic elements. The producer may analyze samples for trace elements not specified in the specification. However, such analysis is not required and may not cover all metallic x201c;Othersx201d; elements. Should any analysis by the producer or the purchaser establish that an x201c;Othersx201d; element exceeds the limit of x201c;Eachx201d; or that the aggregate of several x201c;Othersx201d; elements exceeds the limit of x201c;Total,x201d; the material shall be considered nonconforming.(C)x00a0;Other Elementsx2014;Total shall be the sum of unspecified metallic elements 0.0108201;% or more, rounded to the second decimal before determining the sum.(D)x00a0;Contains silver 0.40x2013;1.08201;%.(E)x00a0;If iron exceeds 0.458201;%, manganese content shall not be less than one half of the iron content.(F)x00a0;Contains beryllium 0.003x2013;0.0078201;%, boron 0.0028201;% max.(G)x00a0;710.0 formerly A712.0, 712.0 formerly D712.0, 851.0 formerly A850.0, 852.0 formerly B850.0. 1.2x00a0;This specification is for aluminum-alloy investment castings used in general purpose applications. It may not address the mechanical properties integrity testing and verification required for highly loaded or safety critical applications. 1.3x00a0;Alloy and temper designations are in accordance with ANSI H35.1/H35.18201;(M). The equivalent Unified Numbering System alloy designations are in accordance with Practice E527. 1.4x00a0;Unless the order specifies the x201c;Mx201d; specification designation, the material shall be furnished to the inch-pound units. 1.5x00a0;For acceptance criteria for inclusion of new aluminum and aluminum alloys and their properties in this specification, see Annex A1 and Annex A2. 1.6x00a0;Unitsx2014;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact......
信息：ICS：77.150.10 CCS：发布：2014 实施：

ASTM A985/A985M-2016 承压部件的钢熔模铸件通用要求的标准规格
简介：1.1x00a0;This specification covers a group of common requirements that are mandatory for steel castings produced by the investment casting process for pressure-containing parts under each of the following ASTM Specifications: x00a0; Title of Specification ASTM Designation x00a0; x00a0; x00a0; Steel Castings, Carbon, Suitable for Fusion Welding, A216/A216M x00a0; for High-Temperature Service x00a0; Steel Castings, Martensitic Stainless and Alloy, for A217/A217M x00a0; Pressure-Containing Parts, Suitable for High- x00a0; x00a0; Temperature Service x00a0; Castings, Austenitic, Austenitic-Ferritic (Duplex), A351/A351M x00a0; for Pressure-Containing Parts x00a0; Steel Castings, Ferritic and Martensitic, for Pressure-
信息：ICS：49.025.10 CCS：H40;J31 发布：2016 实施：

ASTM A494/A494M-2014a 镍和镍合金铸件的标准规格
简介：1.1x00a0;This specification covers nickel, nickel-copper, nickel-copper-silicon, nickel-molybdenum, nickel-chromium, and nickel-molybdenum-chromium alloy castings for corrosion-resistant service. 1.2x00a0;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
信息：ICS：77.150.40 CCS：H43;J32 发布：2014 实施：

ASTM A747/A747M-2016a 沉淀硬化的不锈钢铸件的标准规格
简介：1.1x00a0;This specification covers iron-chromium-nickel-copper corrosion-resistant steel castings, capable of being strengthened by precipitation hardening heat treatment. 1.2x00a0;These castings may be used in services requiring corrosion resistance and high strengths at temperatures up to 600x00b0;F [315x00b0;C]. They may be machined in the solution-annealed condition and subsequently precipitation hardened to the desired high-strength mechanical properties specified in Table S24.1 with little danger of cracking or distortion. 1.3x00a0;The material is not intended for use in the solution-annealed condition. Note 1:x00a0;If the service environment in which the material is to be used is considered conducive to stress-corrosion cracking, precipitation hardening should be performed at a temperature that will minimize the susceptibility of the material to this type of attack. 1.4x00a0;Supplementary requirements of an optional nature are provided for use at the option of the purchaser. The Supplementary requirements shall apply only when specified individually by the purchaser in the purchase order or contract. 1.5x00a0;This specification is expressed in both inch-pound units and in SI units; however, unless the purchase order or contract specifies the applicable M specification designation (SI units), the inch-pound units shall apply. 1.6x00a0;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.6.1x00a0;Within the text, the SI units are shown in brackets.
信息：ICS：77.140.80 CCS：发布：2016 实施：

ASTM A781/A781M-2014 一般工业用一般要求的钢和合金铸件标准规格
简介：1.1x00a0;This specification covers a group of requirements that are mandatory requirements of the following steel casting specifications issued by ASTM. If the product specification specifies different requirements, the product specification shall prevail. ASTM Designation 8201; Title of Specification A27/A27M Steel Castings, Carbon, for General Application A128/A128M Steel Castings, Austenitic Manganese A148/A148M Steel Castings, High Strength, for Structural Purposes A297/A297M Steel Castings, Iron-Chromium and Iron-Chromium-Nickel, Heat Resistant for General Application A447/A447M Steel Castings, Chromium-Nickel-Iron Alloy (25-12 Class), for High-Temperature Service A494/A494M Castings, Nickel and Nickel Alloy A560/A560M Castings, Chromium-Nickel Alloy A743/A743M Castings, Iron-Chromium, Iron-Chromium-Nickel, Corrosion Resistant, for General Application A744/A744M Castings, Iron-Chromium-Nickel, Corrosion Resistant, for Severe A747/A747M Steel Castings, Stainless, Precipitation Hardening A890/A890M Castings, Iron-Chromium-Nickel-Molybdenum Corrosion-Resistant, Duplex (Austenitic/Ferritic) for General Application A915/A915M Steel Castings, Carbon and Alloy, Chemical Requirements Similar to Standard Wrought Grades A958 Steel Castings, Carbon and Alloy, with Tensile Requirements, C......
信息：ICS：77.140.80 (Iron and steel castings) CCS：发布：2014 实施：

ASTM B85/B85M-2014 铝合金压铸件的标准规格
简介：1.1x00a0;This specification covers aluminum-alloy die castings of all compositions. Thirteen of the most commonly die cast alloy compositions are specified, designated as shown in Table 1. (A)x00a0;Analysis shall ordinarily be made only for the elements mentioned in this table. If, however, the presence of other elements is suspected, or indicated in the course of routine analysis, further analysis shall be made to determine that the total of these other elements are not present in excess of specified limits.(B)x00a0;For purposes of acceptance and rejection, the observed value or calculated value obtained from analysis should be rounded off to the nearest unit in the last right-hand place of figures, used in expressing the specified limit, in accordance with the rounding procedure prescribed in Section 3 of Practice E29.(C)x00a0;Limits are in percent maximum unless shown otherwise.(D)x00a0;Alloys 360.0, 380.0, 413.0, C443.0 and 518.0 are suitable for the production of die casting by either the hot-chamber or the cold-chamber process. Die castings of alloys A360.0, A380.0, 383.0, 384.0 and A413.0 may be made only in cold-chamber machines. ASTM designations were established in accordance with Practice B275. ANSI designations were established in accordance with ANSI H35.1/H35.1 (M). UNS designations were established in accordance with Practice E527.(E)x00a0;x201d;Othersx201d; includes listed elements for which no specific limit is shown as well as unlisted metallic elements. The producer may analyze samples for trace elements not specified in the registration or specification. However, such analysis is not required and may not cover all metallic x201c;otherx201d; elements. Should any analysis by the producer or the purchaser establish that the aggregate of several x201c;othersx201d; elements exceeds the limit of the x201c;Totalx201d; the material shall be considered non-conforming.(F)x00a0;The sum of those x201c;othersx201d; metallic elements 0.010 percent or more, each expressed to the second decimal before determining the sum.(G)x00a0;With respect to mechanical properties, alloys A380.0, 383.0 and 384.0 are substantially interchangeable. 1.2x00a0;This specification is not intended for aluminum-alloy die castings used in aerospace applications. 1.3x00a0;Alloy and temper designations are in accordance with ANSI H35.1/H35.1(M). The equivalent unified numbering system alloy designations are in accordance with Practice E527.
信息：ICS：77.150.10 (Aluminium products) CCS：发布：2014 实施：

ASTM A1002-2016 镍铝有序合金铸件的标准规格
简介：1.1x00a0;This specification covers nickel-aluminum ordered alloy castings intended for elevated-temperature applications such as heat-resisting alloy furnace rollers, supports, hangers, and so forth, in environments up to 23008201;x00b0;F (12608201;x00b0;C). 1.2x00a0;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.2.1x00a0;The SI gage length for tension test specimens is in brackets and is considered standard.
信息：ICS：77.120.01 CCS：H60 发布：2016 实施：

ASTM B969/B969M-2014 用模压铸造, 触变铸造和流变铸造半固体铸件法生产的铝合金铸件的标准规格
简介：1.1x00a0;This specification covers aluminum-alloy castings, produced by the thixocast, rheocast, semi-solid, and squeeze casting processes, shown in Table 1. (A)x00a0;When single units are shown, these indicate the maximum amounts permitted.(B)x00a0;Analysis shall be made for the elements for which limits are shown in this table.(C)x00a0;The following applies to all specified limits in this table: For purposes of determining conformance to these limits, an observed value or a calculated value obtained from analysis shall be rounded to the nearest unit in the last right-hand place of figures used in expressing the specified limit in accordance with the rounding method of Practice E29.(D)x00a0;ASTM alloy designations are defined in ANSI H35.1/H35.18201;(M).(E)x00a0;Other includes listed elements for which no specific limit is shown as well as unlisted metallic elements. The producer may analyze samples for trace elements not specified in the specification. However, such analysis is not required and may not cover all metallic Other Elements. Should any analysis by the producer or the purchaser establish that an Other Elements exceeds the limit of Each or that the aggregate of several Other Elements exceeds the limit of Total, the material shall be considered nonconforming.(F)x00a0;Other Elementsx2014;Total shall be the sum of unspecified metallic elements 0.010 % or more, rounded to the second decimal before determining the sum.(G)x00a0;If the iron content exceeds 0.45 %, manganese content shall not be less than one half of the iron.(H)x00a0;The Aluminum Association ruling on the number of decimal places to which Mg percent is expressed is exempted for some long standing alloys. (See A2.2.6.) 1.2x00a0;This specification is not intended for castings used in aerospace applications. 1.3x00a0;Alloy and temper designations are in accordance with......
信息：ICS：77.150.10 CCS：发布：2014 实施：