粉末直压检测标准粉末直压-中析研究所检测

(CMA)

(CNAS)

(ISO)

(高新技术企业)

粉末直压相关标准参考信息

GB/T 11106-2022 金属粉末用圆柱形压坯的压缩测定压坯强度的方法
简介：
信息：ICS：77.160 CCS：H16 发布：2022-03-09 实施：2022-10-01 00:00:00.0

ASTM E1652-2010 金属包覆铂阻温度计、贱金属热电偶和贵金属热电偶制造用氧化镁和氧化铝粉末以及可压扁绝缘体标准规范
简介：1.1 This specification covers the requirements for magnesium oxide (MgO) and aluminum oxide (Al2O3) powders and crushable insulators used to manufacture metal-sheathed platinum resistance thermometers (PRTs), noble metal thermocouples, base metal thermocouples, and their respective cables. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：29.035.30 CCS：N11 发布：2010 实施：

NEN-ISO 3995-1993 ISO 3995-1985 金属粉末．用矩形压坯的横向断裂测定压坯强度
简介：
信息：ICS： CCS：发布：1993 实施：1993

GB/T 11105-2012 金属粉末压坯的拉托拉试验
简介：本标准规定了测定金属粉末成形性的拉托拉试验方法、本标准适用于粉末压坯的耐磨性和端角部分的耐撞击性的测定、
信息：ICS：77.160 CCS：H16 发布：2012-12-31 实施：2013-10-01

ASTM B933-2009 粉末冶金学(P/M)材料微压痕硬度用标准试验方法
简介：Microindentation hardness testing provides a measure of the hardness of the microstructural constituents of a porous material. It indicates the hardness the material would have if there were no pores present and the material was tested using macroindentation hardness methods. Microindentation hardness tests allow the evaluation of specific phases, microstructural constituents, and regions or gradients too small for macroindentation hardness testing.1.1 This test method covers the determination of the microindentation hardness of powder metallurgy (PM) materials. The test method differs from the approach used for pore-free materials in terms of the precautions required to deal with the porosity. 1.2 A method for converting the directly measured indentation lengths to other hardness scales, for example, HRC is described in Appendix X1. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：77.160 (Powder metallurgy) CCS：H70 发布：2009 实施：

DIN ISO 3995-1991 金属粉末.用矩形粉末压制坯块的横向断裂测定压坯强度
简介：This standard specifies a method for the determination of green strength by measuring the transverse rupture strength of compacts of rectangular cross-section.
信息：ICS：77.160 CCS：H22 发布：1991-05 实施：

GB/T 5160-2002 金属粉末生坯强度的测定矩形压坯横向断裂法
简介：本标准规定了用矩形截面压坯的横向断裂强度来测定生坯强度的方法。
信息：ICS：77.040.10 CCS：H71 发布：2002-08-23 实施：2003-03-01

ASTM B312-2009 金属粉末密压试样未烧结强度的标准试验方法
简介：5.1 The green strength value determined under the conditions specified by this test method is influenced by the characteristics of the powder, how it compacts under the specified conditions (i.e., the particle to particle bonding that exists following compacting), and the lubrication system used. 5.2 Knowledge of the green strength value is useful to the production, characterization and utilization of metal powders in the manufacture of PM structural parts and bearings. The test for green strength of a compacted metal powder can be used to: Relate the resistance of a pressed compact to breakage or damage due to handling. Compare the quality of a metal powder or powder mixture from lot to lot. Determine the effect of the addition of a lubricant or other powders to a base powder. Evaluate powder mixing or blending variables. nbsp;nbsp;nbsp;Factors that are known to influence the green strength of a metal powder are particle shape, particle size distribution and compressibility of the metal powder. 5.5 The amount and type of lubricant or other additives and the mixing procedures have a strong effect on the green strength of specimens produced from metal powder mixtures.1.1 This standard covers a test method that may be used to measure the transverse rupture strength of a compacted but unsintered (green) test specimen produced from lubricated or unlubricated metal powders or powder mixtures. 1.2 Green strength is measured by a quantitative laboratory procedure in which the fracture strength is calculated from the force required to break an unsintered test specimen supported as a simple beam while subjected to a uniformly increasing three-point transverse load under controlled conditions. 1.3 This test method is a companion standard to Test Method B 528 that covers the measurement of the transverse rupture strength of sintered PM test specimens. 1.4 With the exception of density values, for which the g/cm3 unit is the industry standard, and mass measurements used to calculate density, the values stated in inch-pound units are to be regarded as the standard. The SI equivalents shown in parentheses have been converted in accordance with IEEE/ASTM Standard SI 10, may be approximate and are only included for information. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. ^REFERENCE: ASTM Standards: B 215 Practices for Sampling Metal Powders B 243 Terminology of Powder Metallurgy B 528 Test Method for Transverse Rupture Strength of Metal Powder Specimens B 925 Practices for Production and Preparation of Powder Metallurgy x00028;PMx00029; Test Specimens B 962 Test Methods for Density of Compacted or Sintered Powder Metallurgy x00028;PMx00029; Products Using Archimedesx02019; Principle E 691 Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
信息：ICS：77.160 (Powder metallurgy) CCS：H70 发布：2009 实施：

PN H04931-1991 金属粉末．紧压（压缩）的测定
简介：Przedmiotem normy jest me-toda oznaczania zg?szczalno?ci proszków metalicznych.
信息：ICS：0359 CCS：发布：1991 实施：

GB/T 11106-1989 金属粉末用圆柱形压坯的压缩测定压坯强度的方法
简介：本标准规定了用圆柱形压坯的压缩测定压坯强度的方法。本标准适用于测定金属粉末的成形性。
信息：ICS：77.040.10 CCS：H23 发布：1989-03-31 实施：1990-03-01

ASTM D6683-2008 测量粉末和其他散装固体松密度的标准试验方法.压应力的作用
简介：The data from this test can be used to estimate the bulk density of materials in bins and hoppers and for material handling applications such as feeders. The test results can be greatly affected by the sample selected for testing. For meaningful results it is necessary to select a representative sample of the particulate solid with respect to moisture (water) content, particle-size distribution and temperature. For the tests an appropriate size sample should be available, and fresh material should be used for each individual test specimen. Initial bulk density, (x03C1;b)initial, may or may not be used as the minimum bulk density. This will depend on the material being tested. For example, the two are often close to the same for coarse (most particles larger than about 6 mm), free-flowing bulk solids, but not for fine, aeratable powders. Bulk density values may be dependent upon the magnitude of the applied mass increments. Traditionally, the applied mass is doubled for each increment resulting in an applied mass increment ratio of 1. Smaller than standard increment ratios may be desirable for materials that are highly sensitive to the applied mass increment ratio. An example of the latter is a material whose bulk density increases 10% or more with each increase in applied mass. Bulk density values may be dependent upon the duration of each applied mass. Traditionally, the duration is the same for each increment and equal to 15 s. For some materials, the rate of compression is such that complete compression (no change in volume with time at a given applied compressive stress) will require significantly more than 15 s. Note 18212;The quality of the result produced by this standard is dependent on the competence of personnel performing it, and the suitability of the equipment and facilities used. Agencies that meet the criteria of Practice D 3740 are generally considered capable of competent and objective testing/sampling/inspection/etc. Users of this standard are cautioned that compliance with Practice D 3740 does not in itself assure reliable results. Reliable results depend on many factors; Practice D 3740 provides a means of evaluating some of those factors. Practice D 3740 was developed for agencies engaged in the testing or inspection (or both) of soil and rock. As such it is not totally applicable to agencies performing this standard. However, users of this standard should recognize that the framework of Practice D 3740 is appropriate for evaluating the quality of an agency performing this standard. Currently there is no known qualifying national authority that inspects agencies that perform this standard.1.1 This test method covers an apparatus and procedure for determining a range of bulk densities of powders and other bulk solids as a function of compressive stress. 1.2 This test method should be performed in the laboratory under controlled conditions of temperature and humidity. 1.3 All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D 6026. 1.3.1 The procedures used to specify how data are collected/recorded or calculated in this standard are regarded as the industry standard. In addition, they are representative of the significant digits that generally should be retained. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the userx2019;s objectives, and it is common practice to increase or reduce significant digits of reported data to be commensurate with these con......
信息：ICS：19.120 (Particle size analysis. Sieving) CCS：A42 发布：2008 实施：

PN H04946-1991 金属粉末．横向压断裂生坯强度的测定
简介：Przedmiotem normy jest ozna-czanie wytrzyma?o?ci na zginanie znormalizowanych wyprasek z proszków metalicznych, jako cechy charak-teryzuj?cej te proszki.
信息：ICS：0359 CCS：发布：1991 实施：

GB/T 11105-1989 金属粉末压坯的拉托拉试验
简介：本标准规定了测定金属粉末成形性的拉托拉试验方法。本标准适用于粉末压坯的耐磨性和端角部位的耐撞击性的测定。
信息：ICS：77.040.10 CCS：H22 发布：1989-03-31 实施：1990-03-01

KS B 2104-2005 金属粉末烧结轴承径向压应力常数测定方法
简介：이 규격은 다음의 금속 분말 소결 함침 베어링(이하 베어링이라 한다.)의 압괴 강도 상수
信息：ICS：21.100.20 CCS：J30 发布：2005-03-17 实施：2005-03-17

HB 5441.8-1989 粉末冶金制品和粉末的性能测试.烧结金属衬套径向压溃强度的测定
简介：本标准规定了圆筒形粉末冶金衬套径向压繥慷鹊牟舛ǚ椒ā?
信息：ICS： CCS：H70 发布：1990-04-11 实施：1990-06-01

GB 11105-1989 金属粉末压坯的拉托拉试验
简介：
信息：ICS： CCS：H23 发布：1989-03-31 实施：1990-03-01

KS B 2104-2005(2010) 烧结金属粉末的直径压坏强度常数确定方法轴承浸渍
简介：
信息：ICS：21.100.20 CCS：发布：2005-03-17 实施：

JUS C.A2.030-1990 金属粉末（不包括硬质合金粉末）．单轴向压缩时压塑性（压缩性）的测定
简介：
信息：ICS： CCS：发布：1990-01-01 实施：

ASTM E1652-21 用于制造贱金属热电偶、金属护套铂电阻温度计和贵金属热电偶的氧化镁和氧化铝粉末及可压碎绝缘子的标准规范
简介：
信息：ICS：17.200.20 CCS：发布：2021-11-01 实施：

SAE AMS 4993C-2004 6Al 4V钛合金混合粉末烧结的压坯
简介：This specification covers a titanium alloy in the form of compacts produced by pressing and sintering a blend of elemental titanium powder and aluminum-vanadium alloy powder. These compacts have been used typically for light weight nuts (B-nuts) used for connecting fluid lines to fittings and to equipment, but usage is not limited to such applications.
信息：ICS：49.025.30 CCS：V11 发布：2004-10-19 实施：

JUS C.A4.058-1990 金属粉末生坯强度的测定．矩形压坯横向断裂法
简介：
信息：ICS： CCS：发布：1990-01-01 实施：

ASTM E1652-2015 基金属热电耦, 金属外壳的铂电阻温度计和贵金属热电偶制造中使用的氧化镁和氧化铝粉末及压扁绝缘子的标准规格
简介：1.1x00a0;This specification covers the requirements for magnesium oxide (MgO) and aluminum oxide (Al2O3) powders and crushable insulators used to manufacture base metal thermocouples, metal-sheathed platinum resistance thermometers (PRTs), noble metal thermocouples, and their respective cables. 1.2x00a0;The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：17.200.20 CCS：发布：2015 实施：

ASTM E1652-03 制造金属护套铂电阻温度计用氧化镁和氧化铝粉末及可压碎绝缘体的标准规范贱金属热电偶和贵金属热电偶
简介：
信息：ICS：17.200.20 CCS：发布：2003-05-10 实施：

SAE AMS 7880B-1987 烧结和压碎的钴涂覆的钨碳化粉末
简介：This specification covers tungsten carbide-cobalt in the form of powder.Primarily for producing plasma spray coatings to provide wear and fretting resistant surfaces.
信息：ICS：49.025.99 CCS：H63 发布：1987-04-01 实施：

ASTM B933-2014 粉末冶金学(P/M)材料微压痕硬度用标准试验方法
简介：5.1x00a0;Microindentation hardness testing provides a measure of the hardness of the microstructural constituents of a porous material. It indicates the hardness the material would have if there were no pores present and the material was tested using macroindentation hardness methods. 5.2x00a0;Microindentation hardness tests allow the evaluation of specific phases, microstructural constituents, and regions or gradients too small for macroindentation hardness testing. 1.1x00a0;This test method covers the determination of the microindentation hardness of powder metallurgy (PM) materials. The test method differs from the approach used for pore-free materials in terms of the precautions required to deal with the porosity. 1.2x00a0;A method for converting the directly measured indentation lengths to other hardness scales, for example, HRC is described in Appendix X1. 1.3x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：77.160 (Powder metallurgy) CCS：H70 发布：2014 实施：

ASTM E1652-2003 金属外壳的铂电阻温度表、基金属热电耦和贵金属温差热电偶制造中使用的氧化镁和氧化铝粉末及压扁绝缘子的标准规范
简介：1.1 This specification covers the requirements for magnesium oxide (MgO) and aluminum oxide (Al2O3) powders and crushable insulators used to manufacture metal-sheathed platinum resistance thermometers (PRTs), noble metal thermocouples, base metal thermocouples, and their respective cables.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：17.200.20 (Temperature-measuring instruments); 29. CCS：N11 发布：2003 实施：

ISO 3995:1985 金属粉末——用矩形压块横向断裂测定压坯强度
简介：
信息：ICS：77.040.10 CCS：发布：1985-07-04 实施：

ASTM D6683-2014 根据压应力函数测定粉末和其它松散固体的容积密度的标准试验方法
简介：5.1x00a0;The data from this test can be used to estimate the bulk density of materials in bins and hoppers and for material handling applications such as feeders. 5.2x00a0;The test results can be greatly affected by the sample selected for testing. For meaningful results it is necessary to select a representative sample of the particulate solid with respect to moisture (water) content, particle-size distribution and temperature. For the tests an appropriate size sample should be available, and fresh material should be used for each individual test specimen. 5.3x00a0;Initial bulk density, (x03c1;b)initial, may or may not be used as the minimum bulk density. This will depend on the material being tested. For example, the two are often close to the same for coarse (most particles larger than about 6 mm), free-flowing bulk solids, but not for fine, aeratable powders. 5.4x00a0;Bulk density values may be dependent upon the magnitude of the applied mass increments. Traditionally, the applied mass is doubled for each increment resulting in an applied mass increment ratio of 1. Smaller than standard increment ratios may be desirable for materials that are highly sensitive to the applied mass increment ratio. An example of the latter is a material whose bulk density increases 10% or more with each increase in applied mass. 5.5x00a0;Bulk density values may be dependent upon the duration of each applied mass. Traditionally, the duration is the same for each increment and equal to 15 s. For some materials, the rate of compression is such that complete compression (no change in volume with time at a given applied compressive stress) will require significantly more than 15 s.Note 1x2014;The quality of the result produced by this standard is dependent on the competence of personnel performing it, and the suitability of the equipment and facilities used. Agencies that meet the criteria of Practice D3740 are generally considered capable of competent and objective testing/sampling/inspection/etc. Users of this standard are cautioned that compliance with Practice D3740 does not in itself assure reliable results. Reliable results depend on many factors; Practice D3740 provides a means of evaluating some of those factors. Practice D3740 was developed for agencies engaged in the testing or inspection (or both) of soil and rock. As such it is not totally applicable to agencies performing this standard. However, users of this standard should recognize that the framework of Practice D3740 is appropriate for evaluating the quality of an agency performing this standard. Currently there is no known qualifying national authority that inspects agencies that perform this standard. 1.1x00a0;This test method covers an apparatus and procedure for determining a range of bulk densities of powders and other bulk solids as a function of compressive stress. 1.2x00a0;This test method should be performed in the laboratory under controlled conditions of temperature and humidity. 1.3x00a0;All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026. 1.3.1x00a0;The procedures used to specify how data are collected/recorded or calculated in this standard are regarded as the industry stan......
信息：ICS：19.120 (Particle size analysis. Sieving) CCS：发布：2014 实施：

DIN EN ISO 3927-2002 金属粉末(不包括硬质合金粉末).单轴向压缩的压塑性测定(ISO 3927:2001); 德文版本 EN ISO 3927:2001
简介：
信息：ICS：77.160 CCS：H71 发布：2002-04 实施：

ISO 3927-1985 金属粉末(不包括硬质合金粉末).单轴向压缩时压塑性(压缩性)的测定
简介：
信息：ICS：77.160 CCS：H22 发布：1985-07 实施：

ASTM E1652-2014 基金属热电耦, 金属外壳的铂电阻温度计和贵金属热电偶制造中使用的氧化镁和氧化铝粉末及压扁绝缘子的标准规范
简介：1.1x00a0;This specification covers the requirements for magnesium oxide (MgO) and aluminum oxide (Al2O3) powders and crushable insulators used to manufacture base metal thermocouples, metal-sheathed platinum resistance thermometers (PRTs), noble metal thermocouples, and their respective cables. 1.2x00a0;The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：17.200.20 (Temperature-measuring instruments); 29. CCS：发布：2014 实施：

KS D ISO 3995-2001 金属粉末.用矩形未烧结压坯测定横断强度
简介：이 규격은 명기된 시험 조건에서 성형체의 직사각 단면에 대한 항절력을 측정하여 성형체 강도
信息：ICS：77.16 CCS：H71 发布：2001-12-31 实施：2001-12-31

ISO 3995-1985 金属粉末用矩形压坯的横向断裂测定压坯强度
简介：This second edition cancels and replaces the first edition (i. e. ISO 3995:1977). The method subjects a compact pressed form metallic powder to a uniformly increasing transverse force under controlled conditions until fracture occurs. the green strength is determined on compacts either having a particular density or after compaction at a specific compacting pressure.
信息：ICS：77.160 CCS：H71 发布：1985-07 实施：

ASTM E1652-2014a 基金属热电耦, 金属外壳的铂电阻温度计和贵金属热电偶制造中使用的氧化镁和氧化铝粉末及压扁绝缘子的标准规范
简介：1.1x00a0;This specification covers the requirements for magnesium oxide (MgO) and aluminum oxide (Al2O3) powders and crushable insulators used to manufacture base metal thermocouples, metal-sheathed platinum resistance thermometers (PRTs), noble metal thermocouples, and their respective cables. 1.2x00a0;The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：17.200.20 (Temperature-measuring instruments); 29. CCS：发布：2014 实施：

KS D ISO 3995-2001(2011) 金属粉末用矩形压坯横向断裂法测定生坯强度
简介：
信息：ICS： CCS：发布：2001-12-31 实施：

CSN 42 0890 Cast.10-1982 金属粉末的测试．金属粉末压坯密度的测定
简介：Schválení ST SEV 2287-80 doporu?ilo federální ministerstvo hutnictví a tě?kého strojírenství.Zpracovatel a oborové normaliza?ní st?edisko: PRAMET, n. p. ?umperk — Miloslav Mosner.Pracovník ??adu pro normalizaci a mě?ení: Milan Skoták.
信息：ICS： CCS：发布：1982-5-3 实施：

KS D ISO 3927-2012 金属粉末(不包括硬质合金粉末).单轴向压缩时压塑性(压缩性)的测定
简介：이 표준은 금속 분말이 규정된 조건에서 표준화된 금형(die)에서 등축 압축 하중으로 성형
信息：ICS：77.160 CCS：H22 发布：2012-10-12 实施：2012-10-12

ASTM E1652-00 制造金属护套铂电阻温度计用氧化镁和氧化铝粉末及可压碎绝缘体的标准规范贱金属热电偶和贵金属热电偶
简介：
信息：ICS：17.200.20 CCS：发布：2000-10-10 实施：

MSZ KGST 2286-1980 金属粉末可挤压度和压碎度的测定
简介：
信息：ICS： CCS：发布：1980-01-01 实施：

ASTM B312-1996 金属粉末密压试样未烧结强度的标准试验方法
简介：1.1 This test method covers determination of the green strength of unsintered compacted metal powder specimens by subjecting them to a uniformly increasing transverse loading under controlled conditions. The term green strength, as used herein, defines the stress, calculated from the flexure formula, required to break a specimen as a simple beam supported near the ends and applying the force midway between the fixed line center of the supports.1.2 The values stated in inch-pound units are to be regarded as the standard. The SI equivalents are in parentheses and may be approximate.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS： CCS：H70 发布：1996 实施：

ISO 3995-1977 金属粉末.矩形压坯横向断裂法测定生坯强度
简介：
信息：ICS：77.040.10 CCS：发布：1977-03-01 实施：

KS D 0410-2012(2022) 温压混合粉末在高温下流量的测定方法
简介：
信息：ICS：77.080.20 CCS：发布：2012-07-27 实施：

ASTM B312-1996(2002) 金属粉末密压试样未烧结强度的标准试验方法
简介：The test for green strength of a compacted metal powder is useful as a: 5.1.1 Method to relate the resistance of a pressed compact to breakage or damage due to handling. 5.1.2 Means of quality comparison of metal powder, lot to lot. 5.1.3 Method of determining the effect of additions to a base powder. Significant variations in green strength will occur if the density tolerance of the pressed bar is exceeded.1.1 This test method covers determination of the green strength of unsintered compacted metal powder specimens by subjecting them to a uniformly increasing transverse loading under controlled conditions. The term green strength, as used herein, defines the stress, calculated from the flexure formula, required to break a specimen as a simple beam supported near the ends and applying the force midway between the fixed line center of the supports.1.2 The values stated in inch-pound units are to be regarded as the standard. The SI equivalents are in parentheses and may be approximate.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：77.160 (Powder metallurgy) CCS：H70 发布：1996 实施：

NBN C 23-106-1975 爆炸压电器．粉末填充保护设备"q"
简介：
信息：ICS： CCS：发布：1976-6-15 实施：

KS D 0410-2012(2017) 温压用混合粉末高温流量测定方法
简介：
信息：ICS：77.080.20 CCS：发布：2012-07-27 实施：

DS/EN 23995-1994 金属粉末．生坯强度的测定．矩形压坯横向断裂法
简介：This International Standard specifies a method for the deter-mination of green strength by measuring the transverse rupture strength of compacts of rectangular cross-section.
信息：ICS：77.160 CCS：发布：1994-05-09 实施：1994-05-09

CSN 42 0809-1973 粉末机械制品压坯
简介：Spracovatel: Závody valiv?ch io?ísk, Mok?ad - ?tefan ?pánik Pracovník ??adu pro normalizaci mě?ení - Vladimír Princ
信息：ICS： CCS：发布：1973-3-14 实施：

KS D 0411-2012(2022) 温压用粉末混合物在高温下表观密度的测定方法
简介：
信息：ICS：77.080.20 CCS：发布：2012-06-25 实施：

NF A95-171-1993 金属粉末.除硬质合金外的金属粉末.在压坯和烧结状态下测定尺寸变化
简介：
信息：ICS：77.160 CCS：H70 发布：1993-08-01 实施：1993-08-05

简介： 信息：

KS D 0411-2012(2017) 为在高温下粉末混合物旨在用于温压表观密度的测定方法
简介：
信息：ICS：77.080.20 CCS：发布：2012-06-25 实施：

NF A95-123-1993 金属粉末.用矩形压坯的横向断裂测定湿压强度
简介：
信息：ICS：77.160 CCS：H70 发布：1993-08-01 实施：1993-08-05

简介： 信息：

DIN EN ISO 3927-2011 不包括硬质合金粉末的金属粉末.单轴向压缩的压塑性测定(ISO 3927-2011).德文版本EN ISO 3927-2011
简介：This International Standard specifies methods for measuring the extent to which a metallic powder is compacted when subjected to uniaxial compressive loading in a confining die under specified conditions. The method is not applicable to powders for hardmetals.
信息：ICS：77.160 CCS：H16 发布：2011-05 实施：

BS EN 23995-1993 金属粉末规范.矩形压坯横向断裂压坯强度的测定
简介：This International Standard specifies a method for the deter-mination of green strength by measuring the transverse rupture strength of compacts of rectangular cross-section.
信息：ICS：77.160 CCS：H70 发布：1993-06-15 实施：1993-06-15

简介： 信息：

ASTM E1652-10 制造金属护套铂电阻温度计用氧化镁和氧化铝粉末及可压碎绝缘体的标准规范贱金属热电偶和贵金属热电偶
简介：
信息：ICS：17.200.20 CCS：发布：2010-05-01 实施：

EN 23995-1993 金属粉末.用矩形压坯的横向断裂测定压坯强度(ISO 3995-1985)
简介：This International Standard specifies a method forThe determination of green strength by measuringThe transverse rupture strength of compacts of rectangular cross-section
信息：ICS：77.160 CCS：发布：1993-01-01 实施：

简介： 信息：