丙烯标准检测标准丙烯标准-中析研究所检测

(CMA)

(CNAS)

(ISO)

(高新技术企业)

丙烯标准相关标准参考信息

ASTM D2163-23 用气相色谱法测定液化石油气和丙烷/丙烯混合物中碳氢化合物的标准试验方法
简介：
信息：ICS：75.160.30 CCS：发布：2023-03-01 实施：

ASTM D7465/D7465M-2015e1 土工膜用片状乙烯-丙烯-二烯三元共聚物 (EPDM) 的标准规格
简介：1.1x00a0;This specification covers flexible sheet made from ethylene propylene diene terpolymer (EPDM) geomembrane intended for use in geotechnical and geoenvironmental applications. The tests and property limits used to characterize the sheet are values to ensure minimum quality for the intended use. The vulcanized rubber sheet may be non-reinforced, fabric or scrim reinforced. 1.2x00a0;In place geomembrane design criteria, such as field seaming strength, and material compatibility, among others, are factors that must be considered but are beyond the scope of this specification. 1.3x00a0;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：59.080.70;83.140.10 CCS：发布：2015 实施：

FORD WSD-M96D21-A2-2010 短纤维绒涂层的乙烯/丙烯三元乙丙橡胶（EPDM）橡胶挡风雨条***与标准FORD WSS-M99P1111-A一起使用***列于标准FORD WSD-M96D21-A1上［使用:FORD WSS-M9P10-A,FORD WSS-M9P10-A］
简介：
信息：ICS： CCS：发布：2010-05-19 实施：

ASTM D2712-23 气相色谱法测定高纯度丙烯中烃类杂质的标准试验方法
简介：
信息：ICS：71.080.10 CCS：发布：2023-03-01 实施：

ASTM D3900-2015 采用红外光谱法对乙烯丙烯共聚物 (EPM) 和乙烯丙烯二烯三元共聚物 (EPDM) 中的乙烯单元进行橡胶测定的标准试验方法
简介：4.1x00a0;These test methods can be used for determining which EPDM polymers are evaluated in the different compounds in Test Methods D3 1.1x00a0;These test methods cover the determination of the proportion of ethylene and propylene units in ethylene-propylene copolymers (EPM) and ethylene-propylenediene terpolymers (EPDM) over the range from 35 to 85 mass8201;% ethylene. Four test methods are needed to encompass the variety of commercial polymers that contain additives or polymerized diene units that interfere with the various infrared peaks. Except when interferences are present, all four test methods should give similar results. The test methods appear in the following order: 1.1.1x00a0;Pressed Film Test Methods: x00a0; 8199;Sections Test Method Ax2014;For EPM and EPDM between 35 and 70 mass8201;% ethylene x2007;9 x2013; 14 Test Method Bx2014;For EPM and EPDM between 60 and 85 mass8201;% ethylene, except for ethylene/propylene/1,4-hexadiene terpolymers 15 x2013; 19 Test Method Cx2014;For all EPM and EPDM polymers between 35 and 85 mass8201;% ethylene, using near infrared 20 x2013; 24 1.1.2x00a0;Cast Film Test Methods:
信息：ICS：83.040.10 CCS：发布：2015 实施：

ASTM D2712-91(2010) 通过气相色谱法测定丙烯浓缩物中碳氢化合物痕迹的标准测试方法
简介：
信息：ICS：71.080.10 CCS：发布：2010-05-01 实施：

ASTM D6047-17(2021) 未加工橡胶的标准试验方法乙烯-丙烯二烯（EPDM）三元共聚物中5-亚乙基降冰片烯（ENB）或二环戊二烯（DCPD）的测定
简介：
信息：ICS：83.060 CCS：发布：2021-11-01 实施：

ASTM D6047-2015 乙烯-丙烯-二烯共聚三聚物 (EPDM) 中5-ENB或双环戊二烯 (DCPD) 生橡胶测定的标准试验方法
简介：1.1x00a0;These test methods cover the determination of the content of 5-ethylidenenorbornene (ENB) or Dicyclopentadiene (DCPD) in ethylene-propylene-diene (EPDM) terpolymers. They are applicable to diene contents in the 0.1 to 10 mass % range. 1.2x00a0;ENB and DCPD are dienes introduced in ethylene/propylene rubbers to generate specific cure properties. Since high precision for diene content determination has become very important, a Fourier Transform Infrared Spectroscopic (FTIR) method was developed. Diene determination was performed in the past by a refractive index technique. Note 1:x00a0;The procedures for % ENB and % DCPD differ only in the location in the infrared (IR) of the IR peak being quantified. 1.3x00a0;The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：83.060 CCS：发布：2015 实施：

ASTM D5492-2010 丙烯塑料中的二甲苯溶解物测定的标准试验方法
简介：The results of this test provide a relative measure of the total soluble fraction of polypropylene homopolymers and copolymers. The soluble fraction approximately correlates to the amorphous fraction in the polypropylene. Xylene is widely used for determining the soluble fraction in polypropylene as it is more specific to the atactic fraction than other solvents. The concentration of a soluble fraction obtained with a specific solvent has been found to relate closely to the performance characteristics of a product in certain applications, for example film and fiber. Data obtained by one solvent and at one precipitation time cannot be compared with data obtained by another solvent or precipitation time, respectively.1.1 This test method is to be used for determining the 25x00B0;C xylene-soluble fraction of polypropylene homopolymers and copolymers. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 18212;This test method is technically equivalent to ISO 16152.
信息：ICS：83.080.20 CCS：G31 发布：2010 实施：

ASTM D8061-21 2-溴-3,3,3-三氟-1-丙烯（CF3CBr=CH2）的搬运、运输和储存的标准实施规程
简介：
信息：ICS：75.160.30 CCS：发布：2021-06-01 实施：

SAE AS 81914/3A-2014 氟化乙烯丙烯 (FEP) 标准卷曲的卷曲螺旋软塑料管材
简介：Scope is unavailable.
信息：ICS：49.060 CCS：发布：2014-01-14 实施：

ASTM F2118-2010 丙烯骨料水泥材料力控疲劳试验恒定幅值的标准试验方法
简介：This test method describes a uniaxial, constant amplitude, fully reversed fatigue test to characterize the fatigue performance of a uniform cylindrical waisted specimen manufactured from acrylic bone cement. This test method considers two approaches to evaluating the fatigue performance of bone cement: Testing is conducted at three stress levels to characterize the general fatigue behavior of a cement over a range of stresses. The stress level and resultant cycles to failure of the specimens can plotted on an S-N diagram. Another approach is to determine the fatigue life of a particular cement. The fatigue life for orthopaedic bone cement is to be determined up to 5 million (5 x00D7; 106) cycles. This test method does not define or suggest required levels of performance of bone cement. This fatigue test method is not intended to represent the clinical use of orthopaedic bone cement, but rather to characterize the material using standard and well-established methods. The user is cautioned to consider the appropriateness of this test method in view of the material being tested and its potential application. It is widely reported that multiple clinical factors affect the fatigue performance of orthopaedic bone cement; however, the actual mechanisms involves multiple factors. Clinical factors which may affect the performance of bone cement include: temperature and humidity, mixing method, time of application, surgical technique, bone preparation, implant design, anatomical site, and patient factors, among others. This test method does not specifically address all of these clinical factors. The test method can be used to compare different acrylic bone cement formulations and products and different mixing methods and environments (that is, mixing temperature, vacuum, centrifugation, and so forth).1.1 This test method describes test procedures for evaluating the constant amplitude, uniaxial, tension-compression uniform fatigue performance of acrylic bone cement materials. 1.2 This test method is relevant to orthopedic bone cements based on acrylic resins, as specified in Specification F451 and ISO 16402. The procedures in this test method may or may not apply to other surgical cement materials. 1.3 It is not the intention of this test method to define levels of performance of these materials. It is not the intention of this test method to directly simulate the clinical use of these materials, but rather to allow for comparison between acrylic bone cements to evaluate fatigue behavior under specified conditions. 1.4 A rationale is given in Appendix X2. 1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：91.100.10 CCS：Q11 发布：2010 实施：

DIN EN 6111-2020 航空航天系列. 乙烯-丙烯弹性体(EPM/EPDM). 硬度为80 IRHD,用于长期应用的液压系统中的静态密封元件. 材料标准; 德文和英文版 EN 6111-2020
简介：This document defines the requirements of ethylene propylene elastomer (EPM/EPDM) for seal elements for use as static seals in hydraulic systems using phosphate ester fluids, hardness 80 IRHD (International Rubber Hardness Degree) for long term application for aerospace applicati
信息：ICS：49.025.40 CCS：发布：2020-11-01 实施：

ASTM D2163-14 通过气相色谱法测定液化石油气（LP）气体和丙烷/丙烯混合物中的烃的标准测试方法
简介：
信息：ICS：75.160.30 CCS：发布：2014-01-01 实施：

ASTM D3568-03(2009) 橡胶的标准试验方法&8212；EPDM（乙烯-丙烯-二烯三元共聚物）的评价包括与油的混合物
简介：
信息：ICS：83.060 CCS：发布：2009-11-01 实施：

ASTM D5303-20 气相色谱法测定丙烯中痕量羰基硫化物的标准试验方法
简介：
信息：ICS：71.080.10 CCS：发布：2020-07-01 实施：

ASTM D2163-14e1 通过气相色谱法测定液化石油气（LP）气体和丙烷/丙烯混合物中的烃的标准测试方法
简介：
信息：ICS：75.160.30 CCS：发布：2014-01-01 实施：

FORD ESA-M2D321-A-2009 碳酸钙和二氧化钛填充的聚氧化丙烯橡胶***与标准FORD WSS-M99P1111-A一起使用***
简介：
信息：ICS： CCS：发布：2009-08-25 实施：

ASTM D2712-20 用气相色谱法测定高纯丙烯中烃类杂质的标准试验方法
简介：
信息：ICS：71.080.10 CCS：发布：2020-07-01 实施：

ASTM D2163-2014e1 用气相色谱法分析液化石油气和丙烯浓缩物的标准试验方法
简介：5.1x00a0;The hydrocarbon component distribution of liquefied petroleum gases and propene mixtures is often required for end-use sale of this material. Applications such as chemical feed stocks or fuel require precise compositional data to ensure uniform quality. Trace amounts of some hydrocarbon impurities in these materials can have adverse effects on their use and processing. 5.2x00a0;The component distribution data of liquefied petroleum gases and propene mixtures can be used to calculate physical properties such as relative density, vapor pressure, and motor octane (see Practice D2598). Precision and accuracy of compositional data are extremely important when these data are used to calculate various properties of these petroleum products. 1.1x00a0;This test method covers the quantitative determination of individual hydrocarbons in liquefied petroleum (LP) gases and mixtures of propane and propene, excluding high-purity propene in the range of C1 to C5. Component concentrations are determined in the range of 0.01 to 100 volume percent. 1.2x00a0;This test method does not fully determine hydrocarbons heavier than C5 and non-hydrocarbon materials, and additional tests may be necessary to fully characterize an LPG sample. 1.3x00a0;The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only. 1.4x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：75.160.30 (Gaseous fuels) CCS：E46 发布：2014 实施：

ASTM D6047-99(2009) 在乙烯 - 丙烯 - 二烯（EPDM）三元共聚物中橡胶原料测定5-乙叉基降冰片烯（ENB）或二环戊二烯（DCPD）的标准测试方法
简介：
信息：ICS：83.060 CCS：发布：2009-01-01 实施：

ASTM D5303-19 气相色谱法测定丙烯中痕量羰基硫化物的标准试验方法
简介：
信息：ICS：71.080.10 CCS：发布：2019-05-01 实施：

ASTM D2163-2014 用气相色谱法分析液化石油气和丙烯浓缩物的标准试验方法
简介：5.1x00a0;The hydrocarbon component distribution of liquefied petroleum gases and propene mixtures is often required for end-use sale of this material. Applications such as chemical feed stocks or fuel require precise compositional data to ensure uniform quality. Trace amounts of some hydrocarbon impurities in these materials can have adverse effects on their use and processing. 5.2x00a0;The component distribution data of liquefied petroleum gases and propene mixtures can be used to calculate physical properties such as relative density, vapor pressure, and motor octane (see Practice D2598). Precision and accuracy of compositional data are extremely important when these data are used to calculate various properties of these petroleum products. 1.1x00a0;This test method covers the quantitative determination of individual hydrocarbons in liquefied petroleum (LP) gases and mixtures of propane and propene, excluding high-purity propene in the range of C1 to C5. Component concentrations are determined in the range of 0.01 to 100 volume percent. 1.2x00a0;This test method does not fully determine hydrocarbons heavier than C5 and non-hydrocarbon materials, and additional tests may be necessary to fully characterize an LPG sample. 1.3x00a0;The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only. 1.4x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：75.160.30 (Gaseous fuels) CCS：E46 发布：2014 实施：

FORD WSS-M4D682-A7-2008 汽车外部用着色模塑的丙烯酸-苯乙烯-丙烯睛共聚物（ASA）+聚碳酸酯（PC）混合物成型料***与标准FORD WSS-M99P1111-A一起使用***
简介：
信息：ICS： CCS：发布：2008-05-15 实施：

ASTM D2163-14(2019) 用气相色谱法测定液化石油气和丙烷/丙烯混合物中碳氢化合物的标准试验方法
简介：
信息：ICS：75.160.30 CCS：发布：2019-05-01 实施：

ASTM D4864-2014 使用气相色谱法测定丙烯浓缩物中甲醇微量元素的标准试验方法
简介：5.1x00a0;Methanol is a common impurity in propylene concentrate. It can have a deleterious effect on various processes that use propylene concentrate as a feedstock. 1.1x00a0;This test method covers the determination of methanol in propylene concentrates in the range of approximately 48201;mg/kg to 40 mg/kg (parts-per-million by mass). 1.2x00a0;The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only. Note 1:x00a0;There is no direct acceptable SI equivalent for screw threads. 1.3x00a0; This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific warning statements are given in 11.1.1, 11.2.1, and 12.11.
信息：ICS：71.080.10 (Aliphatic hydrocarbons) CCS：发布：2014 实施：

ASTM F484-2008 丙烯塑料在与液态或半液态化合物接触中产生的应力的标准试验方法
简介：1.1 This test method covers determination of the crazing effect that a liquid or semi-liquid test compound will have on transparent acrylic plastic material that is under bending stress. 1.2 Three types of acrylic material are covered. One, two, or all of the materials shall be used in the test, as specified by the procuring agency. When not specified otherwise, all three types of acrylic shall be used in the test. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：83.080.10 (Thermosetting materials) CCS：G31 发布：2008 实施：

ASTM D5273-18 丙烯浓缩物分析的标准指南
简介：
信息：ICS：71.080.10 CCS：发布：2018-07-01 实施：

ASTM D3368-2014 氟化乙丙烯(FEP)-碳氟化合物树脂薄板及薄膜的标准规格
简介：1.1x00a0;This specification covers unfilled, unpigmented FEP-fluorocarbon resin sheet and film less than 3.175 mm (0.125 in.) thick. Recycled materials are allowed in accordance with 6.2. 1.2x00a0;The values stated in SI units as detailed in IEEE/ASTM SI 10 are to be regarded as standard and the practices of IEEE/ASTM SI 10 incorporated herein. 1.3x00a0;The following safety hazards caveat pertains only to the test methods portion, Section 14, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 1x2014;There is no known ISO equivalent to this standard.
信息：ICS：83.140.10 (Films and sheets) CCS：发布：2014 实施：

ASTM F484-2008(2013) 丙烯塑料在与液态或半液态化合物接触中产生的应力裂纹的标准试验方法
简介：1.1x00a0;This test method covers determination of the crazing effect that a liquid or semi-liquid test compound will have on transparent acrylic plastic material that is under bending stress. 1.2x00a0;Three types of acrylic material are covered. One, two, or all of the materials shall be used in the test, as specified by the procuring agency. When not specified otherwise, all three types of acrylic shall be used in the test. 1.3x00a0;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：83.080.10 (Thermosetting materials) CCS：G31 发布：2008 实施：

ASTM D2712-18a 用气相色谱法测定高纯丙烯中烃类杂质的标准试验方法
简介：
信息：ICS：71.080.10 CCS：发布：2018-06-01 实施：

ASTM F2118-2014 丙烯骨水泥材料的力控疲劳试验恒定幅值的标准试验方法
简介：5.1x00a0;This test method describes a uniaxial, constant amplitude, fully reversed fatigue test to characterize the fatigue performance of a uniform cylindrical waisted specimen manufactured from acrylic bone cement. 5.2x00a0;This test method considers two approaches to evaluating the fatigue performance of bone cement: 5.2.1x00a0;Testing is conducted at three stress levels to characterize the general fatigue behavior of a cement over a range of stresses. The stress level and resultant cycles to failure of the specimens can plotted on an S-N diagram. 5.2.2x00a0;Another approach is to determine the fatigue life of a particular cement. The fatigue life for orthopaedic bone cement is to be determined up to 5 million (5 x00d7; 106) cycles. 5.3x00a0;This test method does not define or suggest required levels of performance of bone cement. This fatigue test method is not intended to represent the clinical use of orthopaedic bone cement, but rather to characterize the material using standard and well-established methods. The user is cautioned to consider the appropriateness of this test method in view of the material being tested and its potential application. 5.4x00a0;It is widely reported that multiple clinical factors affect the fatigue performance of orthopaedic bone cement; however, the actual mechanisms involves multiple factors. Clinical factors which may affect the performance of bone cement include: temperature and humidity, mixing method, time of application, surgical technique, bone preparation, implant design, anatomical site, and patient factors, among others. This test method does not specifically address all of these clinical factors. The test method can be used to compare different acrylic bone cement formulations and products and different mixing methods and environments (that is, mixing temperature, vacuum, centrifugation, and so forth). 1.1x00a0;This test method describes test procedures for evaluating the constant amplitude, uniaxial, tension-compression uniform fatigue performance of acrylic bone cement materials. 1.2x00a0;This test method is relevant to orthopedic bone cements based on acrylic resins, as specified in Specification F451 and ISO 16402. The procedures in this test method may or may not apply to other surgical cement materials. 1.3x00a0;It is not the intention of this test method to define levels of performance of these materials. It is not the intention of this test method to directly simulate the clinical use of these materials, but rather to allow for comparison between acrylic bone cements to evaluate fatigue behavior under specified conditions. 1.4x00a0;A rationale is given in Appendix X2. 1.5x00a0;The values stated in SI units are to be regarded as standard. No other units of meas......
信息：ICS：91.100.10 CCS：发布：2014 实施：

ASTM D2163-07 用气相色谱法测定液化石油气和丙烷/丙烯混合物中碳氢化合物的标准试验方法
简介：
信息：ICS：75.160.30 CCS：发布：2007-12-01 实施：

ASTM D3568-03(2018) 橡胶的标准试验方法&x2014；EPDM（乙烯-丙烯-二烯三元共聚物）的评价包括与油的混合物
简介：
信息：ICS：83.060 CCS：发布：2018-06-01 实施：

ASTM D3296-2014a 氟化乙丙烯-氟烃聚合物管材的标准规格
简介：1.1x00a0;The tubing is intended for electrical, mechanical, chemical, and medical applications manufactured from extrusion resins made from the copolymer of tetrafluoroethylene and hexafluoropropylene (FEP-fluorocarbon). This specification is for virgin material only and does not address recycled material as it is not appropriate for FEP tubing. Note 1:x00a0;Abbreviations are in accordance with Terminology D1600. Note 2:x00a0;There is no known ISO eqivalent to this standard. 1.2x00a0;The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3x00a0;The following safety hazards caveat pertains only to the test methods portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：23.040.20 (Plastic pipes) CCS：发布：2014 实施：

ASTM D5273-92(2007) 丙烯浓缩物分析的标准指南
简介：
信息：ICS：71.080.10 CCS：发布：2007-11-01 实施：

ASTM D2712-18 用气相色谱法测定高纯丙烯中烃类杂质的标准试验方法
简介：
信息：ICS：71.080.10 CCS：发布：2018-01-19 实施：

ASTM D4864-90(2013) 气相色谱法测定丙烯浓缩物中痕量甲醇的标准试验方法
简介：
信息：ICS：71.080.10 CCS：发布：2013-11-15 实施：

ASTM D5303-92(2007) 气相色谱法测定丙烯中痕量羰基硫化物的标准试验方法
简介：
信息：ICS：71.080.10 CCS：发布：2007-11-01 实施：

ASTM D5492-17 测定丙烯塑料中二甲苯可溶物的标准测试方法
简介：
信息：ICS：83.080.20 CCS：发布：2017-08-01 实施：

ASTM D3012-2013 使用炉内样品旋转器测定丙烯塑料热氧化稳定性的标准试验方法
简介：5.1x00a0;Under the severe conditions of this test method, the specimens undergo degradation at a rate that is dependent upon the thermal endurance of the polypropylene material under examination. 5.2x00a0;The thermal level of this test method is considered sufficiently severe to cause failure of commercial grades of heat-stable polypropylene within a reasonable period of time. If desired, lower temperatures can be applied to estimate the performance of polypropylene materials with lower heat stability. 5.3x00a0;The technique of specimen rotation described in this test method provides an estimate of the life-temperature relationship of polypropylene. If this test method is conducted at different temperatures on the same material, a more reliable estimate of the life-temperature relationship of polypropylene is determined. This test method can be conducted at several temperatures and the data interpreted through use of the Arrhenius relation, by plotting the logarithms of times to failure against the reciprocals of the temperatures in kelvins (K). Temperatures in the range from 100 to 150x00b0;C, with intervals of 10x00b0;C, are suggested for this purpose. 5.4x00a0;The stability as determined under the prescribed test method is not directly related to the suitability of the compound for a use where different conditions prevail. 5.5x00a0;The specimen rotation technique of thermal aging increases the probability that all specimens will be exposed similarly and that the effect of temperature gradients in an oven will be minimized. 1.1x00a0;This test method provides a means for estimating the resistance of polypropylene, in molded form, to accelerated aging by heat in the presence of air using a forced draft oven. 1.2x00a0;The stability determined by this test method is not directly related to the suitability of the material for use when different environmental conditions prevail and shall not be used to predict performance. Note 1x2014;The specified thermal levels in this test method are considered sufficiently severe to cause failure of commercial grades of heat-stable polypropylene within a reasonable period of time. If desired, lower temperatures can be applied to estimate the performance of polypropylene with lower heat stabilities. 1.3x00a0;The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only. 1.4x00a0; This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.Note 2x2014;This test method and ISO 4577x2013;1983 are technically similar but different in preparation of test specimens, thickness of test specimen, measurement of the number of air flow changes in the ovens, and the number of air changes per hour required.......
信息：ICS：83.080.20 (Thermoplastic materials) CCS：G31 发布：2013 实施：

FORD WSD-M2D405-A2-2007 硬度为70 IRHD的实心挡风雨条用乙烯/丙烯三元乙丙橡胶（EPDM）橡胶***与标准FORD WSS-M99P1111-A一起使用***列于标准FORD WSD-M2D405-A1上［使用:FORD WSS-M9P9-A,FORD WSS-M9P9-A,FORD WSS-M9P9-A］
简介：
信息：ICS： CCS：发布：2007-08-14 实施：

ASTM D6047-2017 乙烯-丙烯-二烯共聚三聚物 (EPDM) 中5-ENB或双环戊二烯 (DCPD) 生橡胶测定的标准试验方法
简介：1.1x00a0;These test methods cover the determination of the content of 5-ethylidenenorbornene (ENB) or Dicyclopentadiene (DCPD) in ethylene-propylene-diene (EPDM) terpolymers. They are applicable to diene contents in the 0.1 to 10 mass % range. 1.2x00a0;ENB and DCPD are dienes introduced in ethylene/propylene rubbers to generate specific cure properties. Since high precision for diene content determination has become very important, a Fourier Transform Infrared Spectroscopic (FTIR) method was developed. Diene determination was performed in the past by a refractive index technique. Note 1:x00a0;The procedures for % ENB and % DCPD differ only in the location in the infrared (IR) of the IR peak being quantified. 1.3x00a0;The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5x00a0;This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
信息：ICS：83.060 CCS：G34 发布：2017 实施：

ASTM D5303-92(2012) 气相色谱法测定丙烯中痕量羰基硫化物的标准试验方法
简介：
信息：ICS：71.080.10 CCS：发布：2012-12-01 实施：

FORD WSD-M2D405-A5-2007 天然橡胶（NR）、乙烯/丙烯橡胶（三元乙丙橡胶（EPDM））层压挡风雨条***与标准FORD WSS-M99P1111-A一起使用***［使用:FORD WSS-M9P9-A,FORD WSS-M9P9-A,FORD WSS-M9P9-A］
简介：
信息：ICS： CCS：发布：2007-08-14 实施：

ASTM D3368-2017 氟化乙丙烯(FEP)薄板和薄膜的标准规格
简介：1.1x00a0;This specification covers unfilled, unpigmented FEP resin sheet and film less than 3.175 mm (0.125 in.) thick. Recycled materials are allowed in accordance with 6.2. 1.2x00a0;The values stated in SI units as detailed in IEEE/ASTM SI 10 are to be regarded as standard and the practices of IEEE/ASTM SI 10 incorporated herein. 1.3x00a0;The following safety hazards caveat pertains only to the test methods portion, Section 14, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 1:x00a0;There is no known ISO equivalent to this standard. 1.4x00a0;This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
信息：ICS：83.140.10 CCS：G47 发布：2017 实施：

ASTM D5273-92(2012) 丙烯浓缩物分析的标准指南
简介：
信息：ICS：71.080.10 CCS：发布：2012-12-01 实施：

FORD WSD-M2D405-A3-2007 硬度为80 IRHD的实心挡风雨条用乙烯/丙烯三元乙丙橡胶（EPDM）橡胶***与标准FORD WSS-M99P1111-A一起使用***列于标准FORD WSD-M2D405-A1上［使用:FORD WSS-M9P9-A,FORD WSS-M9P9-A,FORD WSS-M9P9-A］
简介：
信息：ICS： CCS：发布：2007-08-14 实施：

ASTM D5492-2017 测定丙烯类塑料二甲苯溶解度的标准试验方法
简介：5.1x00a0;The results of this test provide a relative measure of the total soluble fraction of polypropylene homopolymers and copolymers. The soluble fraction approximately correlates to the amorphous fraction in the polypropylene. Xylene is widely used for determining the soluble fraction in polypropylene as it is more specific to the atactic fraction than other solvents. The concentration of a soluble fraction obtained with a specific solvent has been found to relate closely to the performance characteristics of a product in certain applications, for example film and fiber. Data obtained by one solvent and at one precipitation time cannot be compared with data obtained by another solvent or precipitation time, respectively. 1.1x00a0;This test method is to be used for determining the 25x00b0;C xylene-soluble fraction of polypropylene homopolymers and copolymers. 1.2x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health and environmental practices and determine the applicability of regulatory limitations prior to use. Note 1:x00a0;This test method is technically equivalent to ISO8201;16152. 1.3x00a0;This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
信息：ICS：83.080.20 CCS：G31 发布：2017 实施：

SAE AS 81914/3-2011 标准回旋式氟化乙烯丙烯(FEP)螺旋回旋状柔性塑料管
简介：THIS DOCUMENT COMPLETELY REVISED, INCLUDING RE-FORMATTING TO AN AEROSPACE STANDARD (AS) UNDER THE JURISDICTION OF SAE AE8-C1 FROM AN AEROSPACE MATERIAL SPECIFICATION UNDER THE JURISDICTION OF SAE AMS 'P' COMMITTEE, TO PROPERLY CLASSIFY AND SUPERSEDE AMS-T-81914/3 MATERIAL SPECIFICATION INCLUDING THE INCORPORATION OF COMMENTS RECEIVED FROM GOVERNMENT AND INDUSTRY, UP-DATE SPECIFICATION REFERENCES, ALIGN WITH SAE GUIDELINES AS NEEDED, INCORPORATE MATERIAL UPDATES, CLARIFY PART NUMBERING, ADD METRICS AND REVIEW FOR KNOWN TECHNICAL PROBLEMS.
信息：ICS：49.060 CCS：V21 发布：2011-01-03 实施：

FORD WSD-M2D405-A1-2007 IRHD硬度为60的实心挡风雨条用乙烯/丙烯三元乙丙橡胶（EPDM）橡胶***与标准FORD WSS-M99P1111-A一起使用***列于标准FORD WSD-M2D405-A1上［使用:FORD WSS-M9P9-A,FORD WSS-M9P9-A,FORD WSS-M9P9-A］
简介：
信息：ICS： CCS：发布：2007-08-14 实施：

ASTM D8061-16 2-溴-3,3,3-三氟-1-丙烯（CF3CBr=CH2）的搬运、运输和储存的标准实施规程
简介：
信息：ICS：75.160.30 CCS：发布：2016-07-01 实施：

ASTM D5492-10 测定丙烯塑料中二甲苯可溶物的标准测试方法
简介：
信息：ICS：83.080.20 CCS：发布：2010-08-01 实施：

FORD WSD-M2D405-A4-2007 硬度为90 IRHD的实心挡风雨条用乙烯/丙烯三元乙丙橡胶（EPDM）橡胶***与标准FORD WSS-M99P1111-A一起使用***列于标准FORD WSD-M2D405-A1上［使用:FORD WSS-M9P9-A,FORD WSS-M9P9-A,FORD WSS-M9P9-A］
简介：
信息：ICS： CCS：发布：2007-08-14 实施：

ASTM D2712-91(2016) 通过气相色谱法测定丙烯浓缩物中碳氢化合物痕迹的标准测试方法
简介：
信息：ICS：71.080.10 CCS：发布：2016-04-01 实施：

ASTM D7106-05(2010) 选择乙烯丙烯二烯三元共聚物（EPDM）土工膜试验方法的标准指南
简介：
信息：ICS：59.080.70 CCS：发布：2010-07-01 实施：

ASTM D3012-2007 用炉内样品旋转器测定丙烯塑料的热氧化稳定性的标准试验方法
简介：Under the severe conditions of this test method, the specimens undergo degradation at a rate that is dependent upon the thermal endurance of the polypropylene material under examination. The thermal level of this test method is considered sufficiently severe to cause failure of commercial grades of heat-stable polypropylene within a reasonable period of time. If desired, lower temperatures can be applied to estimate the performance of polypropylene materials with lower heat stability. The technique of specimen rotation described in this test method provides an estimate of the life-temperature relationship of polypropylene. If this test method is conducted at different temperatures on the same material, a more reliable estimate of the life-temperature relationship of polypropylene is determined. This test method can be conducted at several temperatures and the data interpreted through use of the Arrhenius relation, by plotting the logarithms of times to failure against the reciprocals of the temperatures in kelvins (K). Temperatures in the range from 100 to 150x00B0;C, with intervals of 10x00B0;C, are suggested for this purpose. The stability as determined under the prescribed test method is not directly related to the suitability of the compound for a use where different conditions prevail. The specimen rotation technique of thermal aging increases the probability that all specimens will be exposed similarly and that the effect of temperature gradients in an oven will be minimized.1.1 This test method provides a means for estimating the resistance of polypropylene, in molded form, to accelerated aging by heat in the presence of air using a forced draft oven.1.2 The stability determined by this test method is not directly related to the suitability of the material for use when different environmental conditions prevail and shall not be used to predict performance.Note 1The specified thermal levels in this test method are considered sufficiently severe to cause failure of commercial grades of heat-stable polypropylene within a reasonable period of time. If desired, lower temperatures can be applied to estimate the performance of polypropylene with lower heat stabilities.1.3 The values stated in SI units are to be regarded as the standard. The values in brackets are for information only. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.Note 2This test method and ISO 4577-1983 are technically similar but different in preparation of test specimens, thickness of test specimen, measurement of the number of air flow changes in the ovens, and the number of air changes per hour required.1.4 The purpose of this appendix is to provide a secondary method for determining the number of air exchanges that occur within the forced draft oven used for measurement of thermal oxidative stability.
信息：ICS：83.080.20 (Thermoplastic materials) CCS：G31 发布：2007 实施：

ASTM D7106/D7106M-05(2015)e1 选择乙烯丙烯二烯三元共聚物（EPDM）土工膜试验方法的标准指南
简介：
信息：ICS：59.080.70 CCS：发布：2015-05-01 实施：

ASTM D3900-05a(2010) 通过红外光谱法测定乙烯 - 丙烯共聚物（EPM）和乙烯 - 丙烯 - 二烯三元共聚物（EPDM）中乙烯单元的标准测试方法
简介：
信息：ICS：83.040.10 CCS：发布：2010-06-01 实施：

ASTM D2163-2007 用气相色谱法分析液化石油气和丙烯浓缩物的标准试验方法
简介：The hydrocarbon component distribution of liquefied petroleum gases and propene mixtures is often required for end-use sale of this material. Applications such as chemical feed stocks or fuel require precise compositional data to ensure uniform quality. Trace amounts of some hydrocarbon impurities in these materials can have adverse effects on their use and processing. The component distribution data of liquefied petroleum gases and propene mixtures can be used to calculate physical properties such as relative density, vapor pressure, and motor octane (see Practice D 2598). Precision and accuracy of compositional data are extremely important when these data are used to calculate various properties of these petroleum products.1.1 This test method covers the quantitative determination of individual hydrocarbons in liquefied petroleum (LP) gases and mixtures of propane and propene, excluding high-purity propene in the range of C1 to C5. Component concentrations are determined in the range of 0.01 to 100 volume percent. 1.2 This test method does not fully determine hydrocarbons heavier than C5 and non-hydrocarbon materials, and additional tests may be necessary to fully characterize an LPG sample. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：75.160.30 (Gaseous fuels) CCS：E46;G16 发布：2007 实施：