源分析检测标准源分析-中析研究所检测

(CMA)

(CNAS)

(ISO)

(高新技术企业)

源分析相关标准参考信息

GB/T 42290-2022 压水堆核电厂气载放射性源项分析和控制规范
简介：
信息：ICS：17.240 CCS：发布：2022-12-30 实施：2023-07-01

DIN CEN/TS 16429-2013 固定源排放.导管和堆栈中氯化氢含量的采样和测定.红外分析技术.德文版本CEN/TS 16429-2013
简介：
信息：ICS：13.040.40 CCS：Z60 发布：2013-06 实施：

NF X43-322-1998 空气质量.稳定源辐射.HCI的人工测定方法.第3部分:吸收溶解分析和计算
简介：
信息：ICS：13.040.40 CCS：Z50 发布：1998-07-01 实施：1998-07-05

GB/T 4336-2002 碳素钢和中低合金钢火花源原子发射光谱分析方法(常规法)
简介：碳素钢和中低合金钢火花源原子发射光谱分析方法(常规法)GB/T 4336—2002本标准规定了用火花源原子发射光谱测定碳素钢和中低合金钢中碳、硅、锰、磷、硫、铬、镍、钨、钼、钒、铝、钛、铜、铌、钴、硼、锆、砷、锡含量的方法。本方法适用于电炉、感应炉、电渣炉、转炉等铸态或锻轧样品的分析。本方法可同时测定碳素钢和中低合金钢中的19个元素，各元素测定范围列入表l。表1各元素测定范围┏━━━━━━━┳━━━━━━━━━━━━━━┓┃ 元素 ┃ 测定范围(质量分数)/oA ┃┣━━━━━━━╋━━━━━━━━━━━━━━┫┃ C ┃ 0.005～1．20 ┃┣━━━━━━━╋━━━━━━━━━━━━━━┫┃ Si ┃ 0．005～3．50 ┃┣━━━━━━━╋━━━━━━━━━━━━━━┫┃ Mn ┃ 0．O03～2．00 ┃┣━━━━━━━╋━━━━━━━━━━━━━━┫┃ P ┃ 0．003～O．15 ┃┣━━━━━━━╋━━━━━━━━━━━━━━┫┃ S ┃ 0．002～0．070 ┃┣━━━━━━━╋━━━━━━━━━━━━━━┫┃ Cr ┃ 0．001～2．50 ┃┣━━━━━━━╋━━━━━━━━━━━━━━┫┃ Ni ┃ 0．O01～5．00 ┃┣━━━━━━━╋━━━━━━━━━━━━━━┫┃ W ┃ 0．005～2．00 ┃┣━━━━━━━╋━━━━━━━━━━━━━━┫┃ MO ┃ 0．005～1．20 ┃┣━━━━━━━╋━━━━━━━━━━━━━━┫┃ V ┃ 0．005～0．70 ┃┣━━━━━━━╋━━━━━━━━━━━━━━┫┃ A1 ┃ 0．001～1．50 ┃┣━━━━━━━╋━━━━━━━━━━━━━━┫┃ Ti ┃ 0．001～0．90 ┃┣━━━━━━━╋━━━━━━━━━━━━━━┫┃ Cu ┃ 0．O05～1．O ┃┣━━━━━━━╋━━━━━━━━━━━━━━┫┃ Nb ┃ 0．005～0．50 ┃┣━━━━━━━╋━━━━━━━━━━━━━━┫┃ CO ┃ 0．005～0．40 ┃┣━━━━━━━╋━━━━━━━━━━━━━━┫┃ B ┃ 0．000 5～0．010 ┃┣━━━━━━━╋━━━━━━━━━━━━━━┫┃ Zr ┃ 0．002～0．16 ┃┣━━━━━━━╋━━━━━━━━━━━━━━┫┃ As ┃ 0．002～O．30 ┃┣━━━━━━━╋━━━━━━━━━━━━━━┫┃ Sn ┃ 0．002～0．30 ┃┗━━━━━━━┻━━━━━━━━━━━━━━
信息：ICS：77.040.30 CCS：H11 发布：2002-09-11 实施：2003-02-01

PD CEN/TS 16429-2013 固定源排放.管道和烟囱中氯化氢含量的取样和测定.红外分析技术
简介：This Technical Specification specifies an automatic method for determination of the mass concentration of hydrogen chloride (HCl) in ducts and stacks emitting to atmosphere. It describes the infrared analytical technique, including the sampling and gas conditioning system. The method should fulfil the performance characteristics requirements of this Technical Specification and the expanded uncertainty is less than 20 % relative at the daily Emission Limit Value (ELV). In order to use an alternative method to this method, it is necessary to demonstrate equivalence according to the Technical Specification CEN/TS 14793. It is necessary that the capability to demonstrate equivalence is officially recognised by the national accreditation body or law.
信息：ICS：13.040.40 CCS：Z13 发布：2013-03-01 实施：

DIN EN 1911-3-1998 固定源放射.HCl的手动法测定.第3部分:吸收溶液分析和结果计算
简介：
信息：ICS：13.040.40 CCS：F40 发布：1998-07 实施：

ISO/TS 20224-9-2022 分子生物标记分析.用实时PCR检测食品和饲料中的动物源材料.第9部分:鹅DNA检测方法
简介：
信息：ICS：67.050 CCS：发布：2022-10-05 实施：

ASTM C1428-2011 用单支标准气体源多收集器质谱仪法进行六氟化铀的同位素分析的标准试验方法
简介：Uranium hexafluoride is a basic material used to produce nuclear reactor fuel. To be suitable for this purpose, the material must meet criteria for isotopic composition. This test method is designed to determine whether the material meets the requirements described in Specifications C787 and C996.1.1 This test method is applicable to the isotopic analysis of uranium hexafluoride (UF6) with 235U concentrations less than or equal to 5 % and 234U, 236U concentrations of 0.0002 to 0.1 %. 1.2 This test method may be applicable to the analysis of the entire range of 235U isotopic compositions providing that adequate Certified Reference Materials (CRMs or traceable standards) are available. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：27.120.30 CCS：F46 发布：2011 实施：

EJ/T 1068-1998 X射线荧光分析用钚238源
简介：
信息：ICS：27.120.30 CCS：F51 发布：1998-03-25 实施：1998-09-01

ISO/TS 20224-8-2022 分子生物标记分析.用实时PCR检测食品和饲料中的动物源材料.第8部分:火鸡DNA检测方法
简介：
信息：ICS：67.050 CCS：发布：2022-10-05 实施：

DIN EN 1948-4-2010 固定源排放.PCDD/PCDF和类二氧芑质量浓度测定.第4部分:类二氧(杂)芑PCBs的取样和分析.德文版本EN 1948-4-2010
简介：
信息：ICS：13.040.40 CCS：Z60 发布：2010-12 实施：

EJ/T 1067-1998 X射线荧光分析用镅241源
简介：
信息：ICS：27.120.30 CCS：F51 发布：1998-03-25 实施：1998-09-01

ISO/TS 20224-2-2020 分子生物标志物分析食品和饲料中动物源性物质的实时PCR检测第2部分:绵羊DNA检测方法
简介：
信息：ICS：67.050 CCS：发布：2020-07-31 实施：

BS EN 1948-4-2010 固定源排放.PCDDs/PCDFs和类二氧(杂)芑多氯联苯(PCBs)质量浓度的测定.类二氧(杂)芑多氯联苯(PCBs)的分析和取样
简介：This European Standard specifies sampling from stationary sources, extraction, clean-up, identification and quantification procedures of the dioxin-like PCBs. The procedure described lays down requirements to measure the PCB congeners given in Annex A (see Table A.1). It is applicable to the 12 non- and mono-ortho PCB designated by the WHO. It is optimised to measure PCB concentrations of about 0,01 ng WHOTEQ/m.In addition to the 12 non- and mono-ortho-PCB the present document is also applicable to measure further PCB-congeners like the "marker PCB" 28, 52, 101, 138, 153, 180 (see Annex F).This document specifies a framework of quality control requirements for any PCB sampling, extraction, cleanup, identification and quantification methods to be applied.As a result of their similar chemical behaviour PCBs, as shown in the validation campaign, can be sampled from stationary sources together with the PCDDs/PCDFs. Therefore, it is possible to measure PCBs together with PCDDs/PCDFs by applying EN 1948-1, -2, -3 and -4. The complete sampling procedure is described in EN 1948-1. Each of the three sampling methods of EN 1948-1 can be combined with the methods describedin this document to complete the measurement procedure. EN 1948-1 is an integral part of the complete measurement procedure and is necessary for the determination of PCBs.The analyses of the following PCB congeners is described in this European Standard and is validated in the validation campaign:a) Non-ortho substituted PCBs1) 3,3’,4,4’-TeCB(77)2) 3,4,4’,5-TeCB (81)3) 3,3’,4,4’,5-PeCB (126)4) 3,3’,4,4’,5,5’-HxCB (169)b) Mono-ortho substituted PCBs1) 2,3,3’,4,4’-PeCB (105)2) 2,3,4,4’,5-PeCB (114)3) 2,3’,4,4’,5-PeCB (118)4) 2’,3,4,4’,5-PeCB (123)5) 2,3,3’,4,4’,5-HxCB (156)6) 2,3,3’,4,4’,5’-HxCB (157)7) 2,3’,4,4’,5,5’-HxCB (167)8) 2,3,3’,4,4’,5,5’-HpCB (189)c) Marker PCBs1) 2,4,4'- TriCB (28)2) 2,2',5,5'-TeCB (52)3) 2,2',4,5,5'- PeCB (101)4) 2,2',3,4,4',5'- HxCB (138)5) 2,2',4,4',5,5'- HxCB (153)6) 2,2',3,4,4',5,5'- HpCB (180)
信息：ICS：13.040.40 CCS：Z60 发布：2010-11-30 实施：2010-11-30

ASTM C1344-97(2003) 用单标准气体源质谱仪法进行六氟化铀同位素分析的标准试验方法
简介：
信息：ICS： CCS：发布：1997-08-10 实施：

ISO/TS 20224-1-2020 分子生物标志物分析食品和饲料中动物源性物质的实时PCR检测第1部分:牛DNA检测方法
简介：
信息：ICS：67.050 CCS：发布：2020-07-31 实施：

BS EN 1948-4-2010+A1-2013 固定源排放. PCDD/PCDF和类二氧芑质量浓度测定. 类二氧 (杂) 芑PCB的取样和分析
简介：
信息：ICS：13.040.40 CCS：Z15 发布：2010-11-30 实施：2010-11-30

ASTM C1344-97 用单标准气体源质谱仪法进行六氟化铀同位素分析的标准试验方法
简介：
信息：ICS：27.120.30 CCS：发布：1997-08-10 实施：

ISO/TS 20224-3-2020 分子生物标志物分析食品和饲料中动物源性物质的实时PCR检测第3部分:猪DNA检测方法
简介：
信息：ICS：67.050 CCS：发布：2020-07-31 实施：

农业部1485号公告-17-2010 转基因生物及其产品食用安全检测　外源基因异源表达蛋白质等同性分析导则
简介：本标准规定了同一个基因在不同转基因生物中表达的蛋白质的等同性分析导则。本标准适用于分析比较同一个基因在不同转基因生物中表达的蛋白质的等同性。
信息：ICS：65.220.01 CCS：B04 发布：2010-11-15 实施：2011-01-01

ASTM C1344-1997(2003) 用标准气体源质谱法进行六氟化铀的同位分析的标准试验方法
简介：Uranium hexafluoride is a basic material used to prepare nuclear reactor fuel. To be suitable for this purpose, the material must meet the criteria for isotopic composition. This test method is designed to determine whether the material meets the requirements described in Specifications C 787 and C 996. ASTM Committee C-26 Safeguards Statement: 5.2.1 The material (uranium hexafluoride) to which this test method applies is subject to the nuclear safeguards regulations governing its possession and use. The analytical procedure in this test method has been designated as technically acceptable for generating safeguards accountability data. 5.2.2 When used in conjunction with appropriate certified reference materials (CRMs), this procedure can demonstrate traceability to the national measurement base. However, adherence to this procedure does not automatically guarantee regulatory acceptance of the regulatory safeguards measurements. It remains the sole responsibility of the user of this test method to ensure that its application to safeguards has the approval of the proper regulatory authorities.1.1 This test method covers the isotopic analysis of uranium hexafluoride (UF6) and may be used for the entire range of 235U isotopic compositions for which standards are available.1.2 This test method is applicable to the determination of the isotopic relationship between two UF6 samples. If the abundance of a specific isotope of one sample (the standard) is known, its abundance in the other can be determined. This test method is flexible in that the number of times a given material is admitted to the ion source may be adjusted to the minimum required for a specified precision level.1.3 The sensitivity with which differences between two materials can be detected depends on the measuring system used, but ratio-measuring devices can generally read ratio-of-mol ratio differences as small as 0.0001.1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific hazards statements are given in Section 7.
信息：ICS： CCS：F80 发布：1997 实施：

ISO/TS 20224-5-2020 分子生物标志物分析食品和饲料中动物源性物质的实时PCR检测第5部分:山羊DNA检测方法
简介：
信息：ICS：67.050 CCS：发布：2020-07-31 实施：

EN 1948-4-2010 固定源排放.PCDDs/PCDFs和类二氧(杂)芑多氯联苯(PCBs)质量浓度的测定.类二氧(杂)芑多氯联苯(PCBs)的分析和取样
简介：This European Standard specifies sampling from stationary sources, extraction, clean-up, identification and quantification procedures of the dioxin-like PCBs. The procedure described lays down requirements to measure the PCB congeners given in Annex A (see Table A.1). It is applicable to the 12 non- and mono-ortho PCB designated by the WHO. It is optimised to measure PCB concentrations of about 0,01 ng WHO-TEQPCB/m 3 . In addition to the 12 non- and mono-ortho-PCB the present document is also applicable to measure further PCB-congeners like the "marker PCB" 28, 52, 101, 138, 153, 180 (see Annex F).This document specifies a framework of quality control requirements for any PCB sampling, extraction, clean-up, identification and quantification methods to be applied. As a result of their similar chemical behaviour PCBs, as shown in the validation campaign, can be sampled from stationary sources together with the PCDDs/PCDFs. Therefore, it is possible to measure PCBs together with PCDDs/PCDFs by applying EN 1948-1,-2,-3 and-4. The complete sampling procedure is described in EN 1948-1. Each of the three sampling methods of EN 1948-1 can be combined with the methods described inThis document to complete the measurement procedure. EN 1948-1 is an integral part of the complete measurement procedure and is necessary for the determination of PCBs. The analyses of the following PCB congeners is described inThis European Standard and is validated in the validation campaign: a) Non-ortho substituted PCBs: 1) 3,3',4,4'-TeCB(77) 2) 3,4,4',5-TeCB (81) 3) 3,3',4,4',5-PeCB (126) 4) 3,3',4,4',5,5'-HxCB (169); b) Mono-ortho substituted PCBs: 1) 2,3,3',4,4'-PeCB (105) 2) 2,3,4,4',5-PeCB (114) 3) 2,3',4,4',5-PeCB (118) 4) 2',3,4,4',5-PeCB (123) 5) 2,3,3',4,4',5-HxCB (156) 6) 2,3,3',4,4',5'-HxCB (157) 7) 2,3',4,4',5,5'-HxCB (167) 8) 2,3,3',4,4',5,5'-HpCB (189); c) Marker PCBs: 1) 2,4,4'-TriCB (28) 2) 2,2',5,5'-TeCB (52) 3) 2,2',4,5,5'-PeCB (101) 4) 2,2',3,4,4',5'-HxCB (138) 5) 2,2',4,4',5,5'-HxCB (153) 6) 2,2',3,4,4',5,5'-HpCB (180).
信息：ICS：13.040.40 CCS：发布：2010 实施：

ASTM C1344-1997(2008)e1 用标准气体源质谱法进行六氟化铀的同位分析的标准试验方法
简介：Uranium hexafluoride is a basic material used to prepare nuclear reactor fuel. To be suitable for this purpose, the material must meet the criteria for isotopic composition. This test method is designed to determine whether the material meets the requirements described in Specifications C 787 and C 996. ASTM Committee C-26 Safeguards Statement: The material (uranium hexafluoride) to which this test method applies is subject to the nuclear safeguards regulations governing its possession and use. The analytical procedure in this test method has been designated as technically acceptable for generating safeguards accountability data. When used in conjunction with appropriate certified reference materials (CRMs), this procedure can demonstrate traceability to the national measurement base. However, adherence to this procedure does not automatically guarantee regulatory acceptance of the regulatory safeguards measurements. It remains the sole responsibility of the user of this test method to ensure that its application to safeguards has the approval of the proper regulatory authorities.1.1 This test method covers the isotopic analysis of uranium hexafluoride (UF6) and may be used for the entire range of 235U isotopic compositions for which standards are available. 1.2 This test method is applicable to the determination of the isotopic relationship between two UF6 samples. If the abundance of a specific isotope of one sample (the standard) is known, its abundance in the other can be determined. This test method is flexible in that the number of times a given material is admitted to the ion source may be adjusted to the minimum required for a specified precision level. 1.3 The sensitivity with which differences between two materials can be detected depends on the measuring system used, but ratio-measuring devices can generally read ratio-of-mol ratio differences as small as 0.0001. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific hazards statements are given in Section 7.
信息：ICS：27.120.30 (Fissile materials and nuclear fuel tech CCS：F46 发布：1997 实施：

ISO/TS 20224-4-2020 分子生物标志物分析食品和饲料中动物源性物质的实时PCR检测第4部分:鸡DNA检测方法
简介：
信息：ICS：67.050 CCS：发布：2020-07-31 实施：

ASTM C1344-97(2008)e1 用单标准气体源质谱仪法进行六氟化铀同位素分析的标准试验方法
简介：
信息：ICS：27.120.30 CCS：发布：2008-12-01 实施：

ASTM C1344-1997 用标准气体源质谱法进行六氟化铀的同位分析的标准试验方法
简介：1.1 This test method covers the isotopic analysis of uranium hexafluoride (UF6) and may be used for the entire range of 235U isotopic compositions for which standards are available. This test method is adaptable to the determination of any uranium isotope. 1.2 This test method is applicable to the determination of the isotopic relationship between two UF6 samples. If the abundance of a specific isotope of one sample (the standard) is known, its abundance in the other can be determined. This test method is flexible in that the number of times a given material is admitted to the ion source may be adjusted to the minimum required for a specific precision level. 1.3 The sensitivity with which differences between two materials can be detected depends on the measuring system used, but ratio-measuring devices can generally read ratio-of-mol ratio differences as 0.0001. 1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific hazards statements are given in Section 7.
信息：ICS：27.120.30 (Fissile materials and nuclear fuel tech CCS：F80 发布：1997 实施：

ISO/TS 20224-7-2020 分子生物标志物分析食品和饲料中动物源性物质的实时PCR检测第7部分:驴DNA检测方法
简介：
信息：ICS：67.050 CCS：发布：2020-07-31 实施：

ASTM C1344-97(2008) 用单标准气体源质谱仪法进行六氟化铀同位素分析的标准试验方法
简介：
信息：ICS： CCS：发布：2008-12-01 实施：

EJ/T 805-1993 X射线荧光分析用低能光子源
简介：
信息：ICS：27.120.30 CCS：F50 发布：1993-12-13 实施：1994-05-01

ISO/TS 20224-6-2020 分子生物标志物分析食品和饲料中动物源性物质的实时PCR检测第6部分:马DNA检测方法
简介：
信息：ICS：67.050 CCS：发布：2020-07-31 实施：

DIN CEN/TS 1948-4-2007 固定源排放物.PCDDs/PCDFs和二氧芑类PCBs质量浓度的测定.第4部分:二氧芑类PCBs的取样和分析
简介：
信息：ICS：13.040.40 CCS：Z60 发布：2007-10 实施：

SIS SS 02 84 26-1991 空气分析，固定源排放气体运输管道中颗粒材料的浓度和质量流率测定．人工重力法
简介：
信息：ICS： CCS：发布：1991-12-4 实施：

NB/T 20530-2018 压水堆核电厂运行状态设计基准源项分析准则
简介：
信息：ICS：27.120.20 CCS：F70 发布：2018-12-10 实施：2019-04-01

DD CEN/TS 1948-4-2007 固定源排放.PCDDs/PCDFs和类二氧芑PCBs质量浓度测定.第4部分:类二氧芑PCBs的取样和分析
简介：This document specifies sampling from stationary sources, extraction, clean-up, identification andquantification procedures of the dioxin-like PCBs. The procedure described lays down requirements tomeasure the PCB congeners given in Annex A (see Table A.1). It is applicable to the twelve non- and monoorthoPCB designated by the WHO. It is optimised to measure PCB concentrations in the range of 0,01 ngWHO-TEQ/m.In addition to the 12 non- and mono-ortho-PCB the present document is also applicable to measure furtherPCB-congeners like the so-called “marker PCB” 28, 52, 101, 138, 153, 180 (see Annex D).This document specifies a framework of quality control requirements which have to be fulfilled by any PCBsampling, extraction, clean-up, identification and quantification methods to be applied.It is assumed that due to their similar chemical behaviour PCBs may be sampled from stationary sourcestogether with the PCDDs/PCDFs by the same methods. The complete sampling procedure is described in theEN 1948-1. Each of the three sampling methods of EN 1948-1 can be combined with the methods described in this document to complete the measurement procedure. EN 1948-1 is an integral part of the completemeasurement procedure and is necessary for the determination of PCBs.In addition it is possible to measure PCBs together with PCDDs/PCDFs by applying EN 1948 Part 1, Part 2,Part 3 and CEN/TS 1948 Part 4.
信息：ICS：13.040.40 CCS：Z60 发布：2007-08-31 实施：

SIS SS 02 84 25-1991 空气分析．固定源排放氮氧化物的质量浓度的测定，性能特点和校准自动测量系统
简介：
信息：ICS： CCS：发布：1991-12-4 实施：

NB/T 20470-2017 核电厂选址假想事故源项分析准则
简介：
信息：ICS：27.120.10 CCS：F70 发布：2017-04-01 实施：2017-10-01

BS DD CEN/TS 1948-4-2007 固定源排放.PCDD/PCDF和类二氧芑PCBs质量浓度的测定.类二氧芑PCBs的取样和分析
简介：This document specifies sampling from stationary sources, extraction, clean-up, identification and quantification procedures of the dioxin-like PCBs. The procedure described lays down requirements to measure the PCB congeners given in Annex A (see Table A.1). It is applicable to the twelve non- and monoortho PCB designated by the WHO. It is optimised to measure PCB concentrations in the range of 0,01 ng WHO-TEQ/m. In addition to the 12 non- and mono-ortho-PCB the present document is also applicable to measure further PCB-congeners like the so-called “marker PCB” 28, 52, 101, 138, 153, 180 (see Annex D). This document specifies a framework of quality control requirements which have to be fulfilled by any PCB sampling, extraction, clean-up, identification and quantification methods to be applied. It is assumed that due to their similar chemical behaviour PCBs may be sampled from stationary sources together with the PCDDs/PCDFs by the same methods. The complete sampling procedure is described in the EN 1948-1. Each of the three sampling methods of EN 1948-1 can be combined with the methods described in this document to complete the measurement procedure. EN 1948-1 is an integral part of the complete measurement procedure and is necessary for the determination of PCBs. In addition it is possible to measure PCBs together with PCDDs/PCDFs by applying EN 1948 Part 1, Part 2, Part 3 and CEN/TS 1948 Part 4.
信息：ICS：13.040.40 CCS：Z60 发布：2007-08-31 实施：2007-08-31

SIS SS 02 84 21-1990 空气分析．固定源排放二氧化硫质量浓度的测定．过氧化氢，高氯酸钡方法
简介：
信息：ICS： CCS：发布：1990-3-14 实施：

NB/T 20444-2017 压水堆核电厂设计基准事故源项分析准则
简介：
信息：ICS：27.120.20 CCS：F65 发布：2017-04-01 实施：2017-10-01

NF A08-700-2007 铜和铜合金.火花源发射光谱测定法(S-OES)分析
简介：
信息：ICS：77.120.30 CCS：H62 发布：2007-08-01 实施：2007-08-11

SJ/Z 3206.2-1989 发射光谱分析用激发源及其性能要求
简介：本标准适用于光谱分析用的激发源及其性能要求。用于指导光谱分析工作者选择激发源，并确定其分析方法。
信息：ICS：31.020 CCS：L90 发布：1989-02-01 实施：1989-03-01

YY/T 0771.4-2015 动物源医疗器械第4部分:传播性海绵状脑病(TSE)因子的去除和/或灭活及其过程确认分析的原则
简介：为帮助确定无活力动物组织来源的医疗器械的加工过程是否有助于减少传播性海绵状脑病(TSEs)的医源性传播的风险,本部分为设计和开展确认分析提供建议。加工动物组织所使用的TSE去除方法也宜减少通过人源性无活力组织传播TSE感染的风险;本部分不涉及这一方面。一些关于人体组织和TSEs的当前信息可通过类推适用于其他动物组织。本部分不预期为ISO 22442-1:2007的附录C中所列出的已识别出的具有TSE因子污染的“可忽略风险”的特定材料提供方法的确认要求。本部分预期用于解释ISO 22442系列中最终国际标准草案以及ISO 14160标准。本部分是建立在对ISO 22442-3中与TSE因子相关的特定讨论的基础之上并努力总结TSE因子去除领域内当前最新技术水平。随着对TSE因子的灭活和去除的深入理解,可行时将会对本文件进行修订。
信息：ICS：11.100.20 CCS：C30 发布：2015-03-02 实施：2016-01-01

DIN EN 15079-2007 铜和铜合金.火花源发射光谱测定法(S-OES)分析
简介：This European Standard specifies a routine method for the analysis or copper and copper alloys by spark source opitcal emission spectrometry (S-OES). The method is applocable to all elements except copper commonly present in copper and copper alloys present as impurities or minor or main constituents, and detectable by S-OES.
信息：ICS：77.040.30;77.120.30 CCS：H62 发布：2007-08 实施：

TS 894-1970 植物源食用油的分析方法
简介：
信息：ICS： CCS：发布：1970-01-01 实施：

PD CEN/TS 1948-4-2007 固定源排放.PCDDs/PCDFs和类戴奥辛PCBs质量浓度的测定.第4部分:二氧芑类PCBs的取样和分析
简介：
信息：ICS： CCS：发布：2007-07-01 实施：

空气和废气监测分析方法 7.4.1-2003 第七篇化学质量平衡(CMB)受体模型及其在环境空气颗粒物源解析中的应用第四章源与受体样品的分析方法一滤膜的称量
简介：空气和废气监测分析方法
信息：ICS： CCS：发布：实施：

ASTM C1322-2015 先进陶瓷断裂源的断口分析和特性描述的标准实施规程
简介：5.1x00a0;This practice is suitable for monolithic and some composite ceramics, for example, particulate- and whisker-reinforced and continuous-grain-boundary phase ceramics. (Long- or continuous-fiber reinforced ceramics are excluded.) For some materials, the location and identification of fracture origins may not be possible due to the specific microstructure. 5.2x00a0;This practice is principally oriented towards characterization of fracture origins in specimens loaded in so-called fast fracture testing, but the approach can be extended to include other modes of loading as well. 5.3x00a0;The procedures described within are primarily applicable to mechanical test specimens, although the same procedures may be relevant to component fracture analyses as well. It is customary practice to test a number of specimens (constituting a sample) to permit statistical analysis of the variability of the materialx2019;s strength. It is usually not difficult to test the specimens in a manner that will facilitate subsequent fractographic analysis. This may not be the case with component fracture analyses. Component fracture analysis is sometimes aided by cutting test pieces from the component and fracturing the test pieces. Fracture markings and fracture origins from the latter may aid component interpretation. 5.4x00a0;Optimum fractographic analysis requires examination of as many similar specimens or components as possible. This will enhance the chances of successful interpretations. Examination of only one or a few specimens can be misleading. Of course, in some instances the fractographer may have access to only one or a few fractured specimens or components. 5.5x00a0;Successful and complete fractography also requires careful consideration of all ancillary information that may be available, such as microstructural characteristics, material fabrication, properties and service histories, component or specimen machining, or preparation techniques. 5.6x00a0;Fractographic inspection and analysis can be a time-consuming process. Experience will in general enhance the chances of correct interpretation and characterization, but will not obviate the need for time and patience. Repeat examinations are often fruitful. For example, a particular origin type or key feature may be overlooked in the first few test pieces of a sample set. As the fractographer gains experience by looking at multiple examples, he or she may begin to appreciate some key feature that was initially overlooked. 5.7x00a0;This practice is applicable to quality control, materials research and development, and design. It will also serve as a bridge between mechanical testing standards and statistical analysis practices to permit comprehensive interpretation of data for design. An important feature of this practice is the adoption of a consistent manner of characterizing fracture origins, including origin nomenclature. This will further enable the construction of efficient computer databases. 5.8x00a0;The irregularities which act as fracture origins in advanced ceramics can develop during or after fabrication of the material. Large irregularities (relative to the average size of the microstructural feat......
信息：ICS：19.060 ; 81.060.99 ; 81.060.30 CCS：发布：2015 实施：

BS EN 15079-2007 铜和铜合金.火花源发射光谱测定法(S-OES)分析
简介：
信息：ICS：77.120.30 CCS：H62 发布：2007-06-29 实施：2007-06-29

空气和废气监测分析方法 7.4.2-2003 第七篇化学质量平衡(CMB)受体模型及其在环境空气颗粒物源解析中的应用第四章源与受体样品的分析方法二源与受体样品的分析技术
简介：空气和废气监测分析方法
信息：ICS： CCS：发布：实施：

DIN EN 1948-4-2014 固定源排放. PCDD/PCDF和二恶英类PCB质量浓度的测定. 第4部分: 二恶英类PCB的取样和分析; 德文版本EN 1948-4-2010+A1-2013
简介：
信息：ICS：13.040.40 CCS：Z10 发布：2014-03 实施：

EN 15079-2007 铜和铜合金.火花源发射光谱测定法(S-OES)分析
简介：This European Standard specifies a routine method for the analysis of copper and copper alloys by sparksource optical emission spectrometry (S-OES). The method is applicable to all elements except coppercommonly present in copper and copper alloys present as impurities or minor or main constituents, anddetectable by S-OES.
信息：ICS：77.120.30 CCS：H13 发布：2007-05-01 实施：

简介： 信息：

NF X43-324-4/IN1-2014 固定源排放.PCDD/PCDF和类二氧芑质量浓度测定.第4部分:类似PCBs的取样和分析
简介：
信息：ICS：13.040.40 CCS：Z15 发布：2014-01-04 实施：2014-01-04

ASTM C1428-1999 用单支架气体源多收集器质谱仪法进行六氟化铀的同位素分析的标准试验方法
简介：1.1 This test method is applicable to the isotopic analysis of uranium hexafluoride (UF6) with 235U concentrations less than or equal to 5 % and 234U, 236U concentrations of 0.001 to 0.1 %. 1.2 This test method may be applicable to the analysis of the entire range of 235U isotopic compositions providing that adequate standards are available. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：27.120.30 (Fissile materials and nuclear fuel tech CCS：F46 发布：1999 实施：

简介： 信息：

NF X43-324-4-2014 固定源排放. PCDD/PCDF和二恶英类PCB质量浓度的测定. 第4部分: 二恶英类PCB的取样和分析
简介：La présente Norme européenne spécifie les modes opératoires de prélèvement à partir de sources fixes, d'extraction, de purification, d'identification et de quantification des PCB de type dioxine. Le mode opératoire décrit pose les exigences pour mesurer les congénères des PCB données à l'Annexe A (voir Tableau A.1). Il est applicable aux 12 PCB non-ortho et mono-ortho désignés par l'OMS. Il est optimisé pour mesurer des concentrations de PCB d'environ 0,01 ng d'OMS-TEQPCB/m3.En plus des 12 PCB non-ortho et mono-ortho, le présent document est également applicable pour mesurer d'autres congénères de PCB comme le "marqueur de PCB" 28, 52, 101, 138, 153, 180 (v
信息：ICS：13.040.40 CCS：Z15 发布：2014-01-04 实施：2014-01-04

ASTM C1428-1999(2005) 用单支架气体源多收集器质谱仪法进行六氟化铀的同位素分析的标准试验方法
简介：Uranium hexafluoride is a basic material used to produce nuclear reactor fuel. To be suitable for this purpose, the material must meet criteria for isotopic composition. This test method is designed to determine whether the material meets the requirements described in Specifications C 787 and C 996.1.1 This test method is applicable to the isotopic analysis of uranium hexafluoride (UF6) with 235U concentrations less than or equal to 5 % and 234U, 236U concentrations of 0.001 to 0.1 %. 1.2 This test method may be applicable to the analysis of the entire range of 235U isotopic compositions providing that adequate standards are available. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：27.120.30 (Fissile materials and nuclear fuel tech CCS：F46 发布：1999 实施：

简介： 信息：