(CMA)
(CNAS)
(ISO)
(高新技术企业)
水中丙烯酸标准相关标准参考信息
ASTM F2118-14(2020) 丙烯酸骨水泥材料力控制疲劳试验恒定振幅标准试验方法
简介：
信息：ICS：91.100.10 CCS： 发布：2020-09-01 实施：
FORD WSP-M2D373-A2-2010 乙烯/丙烯酸（AEM）橡胶低压缩永久变形油封圈***与标准FORD WSS-M99P1111-A一起使用***
简介：
信息：ICS： CCS： 发布：2010-06-25 实施：
FORD WSB-M4D833-A-2006 汽车外部用丙烯酸-苯乙烯-丙烯睛共聚物（ASA）中等耐热性成型料**与标准FORD WSS-M99P1111-A一起使用**
简介：
信息：ICS： CCS： 发布：2006-04-12 实施：
ASTM E2075/E2075M-15(2020) 使用丙烯酸棒验证AE传感器响应的一致性的标准实践
简介：
信息：ICS：19.100 CCS： 发布：2020-06-01 实施：
ASTM E2075/E2075M-10 使用丙烯酸棒验证AE传感器响应的一致性的标准实践
简介：
信息：ICS：19.100 CCS： 发布：2010-06-01 实施：
FORD ESB-M99J371-A1-2006 可用水稀释的丙烯酸保护涂层***与标准FORD WSS-M99P1111-A一起使用***
简介：
信息：ICS： CCS： 发布：2006-03-21 实施：
ASTM D4802-16 聚（甲基丙烯酸甲酯）丙烯酸塑料片的标准规格
简介：
信息：ICS：83.140.10 CCS： 发布：2016-05-01 实施：
ASTM E2075/E2075M-2010 丙烯酸棒测定声发射传感器响应一致性的标准实施规程
简介：Degradation in sensor performance can occur due to dropping, mechanical shock while mounted on the test structure, temperature cycles, and so forth. It is necessary and desirable to have a simple measurement procedure that will check the consistency of sensor response, while holding all other variables constant. While test blocks of many different kinds have been used for this purpose for many years, an acrylic polymer rod offers the best all-around combination of suitable acoustic properties, practical convenience, ease of procurement and low cost. Because the acoustic properties of the acrylic rod are known to depend on temperature, this practice requires that the rod, sensors, and couplant be stabilized at the same working temperature, prior to verifying the sensors. Attention should be paid to storage conditions for the acrylic polymer rod. For example, it should not be left in a freezing or hot environment overnight, unless it is given time for temperature stabilization before use. Properly applied and with proper record keeping, this practice can be used in many ways. The user organization must determine the context for its use, the acceptance standards and the actions to be taken based on the lead break results. The following uses are suggested: To determine when a sensor is no longer suitable for use. To check sensors that have been exposed to high-risk conditions, such as dropping, overheating, and so forth. To get an early warning of sensor degradation over time. This can lead to identifying conditions of use, which are damaging sensors, and thus, to better equipment care and lower replacement costs. To obtain matched sets of sensors, preamplifiers, instrumentation channels, or a combination thereof, for more uniform performance of the total system. To save time and money, by eliminating the installation of bad sensors. To verify sensors quickly but consistently in the field and to assist trouble-shooting when a channel does not pass a performance check. All the above uses are recommended for consideration. The purpose of this practice is not to call out how these uses are to be implemented, but only to state how the test itself is to be performed so that the results obtained will be accurate and reliable.1.1 This practice is used for routinely checking the sensitivity of acoustic emission (AE) sensors. It is intended to provide a reliable, precisely specified way of comparing a set of sensors, or telling whether an individual sensor''s sensitivity has degraded during its service life, or both. 1.2 This practice is not a x201C;calibrationx201D; nor does it give frequency response information. 1.3 Units8212;The values stated in SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：19.100 CCS：L31 发布：2010 实施：
FORD ESB-M99J343-A-2006 汽车外部用低挥发性有机化合物丙烯酸磁漆低温烘干修复工艺用传统高含固量酸性催化剂***与标准FORD WSS-M99P1111-A一起使用***
简介：
信息：ICS： CCS： 发布：2006-03-09 实施：
ASTM D5098-16 艺术家丙烯酸分散涂料的标准规格
简介：
信息：ICS：87.040 CCS： 发布：2016-02-01 实施：
FORD WSD-M2D447-A2-2009 硬度为80的耐油和酸性水性冷凝物的乙烯/丙烯酸（AEM）橡胶***与标准FORD WSS-M99P1111-A一起使用***
简介：
信息：ICS： CCS： 发布：2009-08-28 实施：
FORD ESB-M99J342-A-2006 汽车外部用低挥发性有机化合物丙烯酸磁漆低温烘干修复工艺用高含固量酸性催化剂***与标准FORD WSS-M99P1111-A一起使用***
简介：
信息：ICS： CCS： 发布：2006-03-09 实施：
ASTM D5098-2016 美术用丙烯酸分散型涂料的标准规格
简介：4.1x00a0;This specification establishes quality requirements and provides a basis for common understanding among producers, distributors, and users. 4.2x00a0;It is not intended that all paints meeting the requirements be identical nor of uniform excellence in all respects. Variations in manufacture, not covered by this specification, may cause some artists to prefer one brand over another, either of which may be acceptable under this specification. 1.1x00a0;This specification establishes requirements for composition, physical properties, performance, and labeling of artists' acrylic emulsion paints. 1.2x00a0;This specification covers pigments, vehicles, and additives. Requirements are included for pigment identification, lightfastness, bleeding, consistency, and drying time. 1.3x00a0;Table 1 lists some pigments meeting the lightfastness requirements in this specification. In order to identify other pigments that meet these requirements, instructions are given for test specimen preparation. Test methods for determining relative lightfastness are referenced. Colour Index Name Lightfastness Category Common Name and Chemical Class Colour Index Number Acrylic x00a0; x00a0; YELLOWS x00a0;
信息：ICS：87.040 CCS： 发布：2016 实施：
FORD WSD-M2D447-A3-2009 硬度为60的耐油乙烯/丙烯酸（AEM）橡胶***与标准FORD WSS-M99P1111-A一起使用***
简介：
信息：ICS： CCS： 发布：2009-08-28 实施：
FORD SK-M99J9565-B-2006 丙烯酸修复面漆用酸性催化剂***与标准FORD WSS-M99P1111-A一起使用***
简介：
信息：ICS： CCS： 发布：2006-02-21 实施：
ASTM D4802-2016 聚甲基丙烯酸甲酯丙烯酸塑料板的标准规格
简介：1.1x00a0;This specification covers monolithic methacrylate sheets produced by various processes. For this specification, methacrylate sheet shall be composed of polymerized acrylic monomers of which at least 808201;% shall be methyl methacrylate. Note 1:x00a0;This specification is intended to consolidate the requirements of the Cast Methacrylate Plastic Sheets portion of discontinued Fed. Spec. L-P-391D, discontinued Specification D702. Cast Methacrylate Plastic Sheets, Rods, Tubes and Shapes, and discontinued Specification D1547, Extruded Acrylic Plastic Sheet. 1.2x00a0;This specification is intended to cover acrylic sheet for general-purpose applications. For specialty applications consult the appropriate use standards. 1.3x00a0;The following safety hazards caveat pertains only to the test methods portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.4x00a0;Acrylic sheet is used frequently in applications in which extreme clarity, lack of optical distortion and absence of any foreign particulate matter are of primary significance. Reground material is suitable for use as long as careful control is used to eliminate adverse effects on these properties. The use of recycled material in type B-1 and B-2 sheet, is not suitable for use when these properties are adversely affected. The use of recycled or reground material is not possible for type A-1 and A-2 materials since the sheet is produced directly from monomer Note 2:x00a0;This standard and ISO 7823-1 address the same subject matter, but differ in technical content.
信息：ICS：83.140.10 CCS： 发布：2016 实施：
FORD ESA-M4D396-A-2009 苯乙烯改性丙烯酸树脂***与标准FORD WSS-M99P1111-A一起使用***
简介：
信息：ICS： CCS： 发布：2009 实施：
FORD WSB-M3G221-A-2006 车内用中等粘性丙烯酸系树脂双面涂布压敏粘合胶带***与标准FORD WSS-M99P1111-A一起使用***
简介：
信息：ICS： CCS： 发布：2006-02-15 实施：
ASTM D4802-15 聚（甲基丙烯酸甲酯）丙烯酸塑料片的标准规格
简介：
信息：ICS：83.140.10 CCS： 发布：2015-12-15 实施：
FORD WSS-M99C113-B-2009 可喷施的含丙烯酸树脂胶粘剂的水基四氟乙烯润滑剂***与标准FORD WSS-M99P1111-A一起使用***
简介：
信息：ICS： CCS： 发布：2009 实施：
FORD WSK-M3G199-A1-2006 标称厚度0.05 MM的汽车内部用丙烯酸双面压敏胶带***与标准FORD WSS-M99P1111-A一起使用***
简介：
信息：ICS： CCS： 发布：2006-01-27 实施：
ASTM E2075/E2075M-15 使用丙烯酸棒验证AE传感器响应的一致性的标准实践
简介：
信息：ICS：19.100 CCS： 发布：2015-06-01 实施：
FORD WSS-M4D682-A7-2008 汽车外部用着色模塑的丙烯酸-苯乙烯-丙烯睛共聚物（ASA）+聚碳酸酯（PC）混合物成型料***与标准FORD WSS-M99P1111-A一起使用***
简介：
信息：ICS： CCS： 发布：2008-05-15 实施：
FORD WSK-M3G199-A2-2006 标称厚度0.13 MM的汽车内部用丙烯酸双面压敏胶带***与标准FORD WSS-M99P1111-A一起使用***列于标准WSK-M3G199-A1上
简介：
信息：ICS： CCS： 发布：2006-01-27 实施：
ASTM D4802-2015 聚甲基丙烯酸甲酯丙烯酸塑料薄板的标准规格
简介：1.1x00a0;This specification covers monolithic methacrylate sheets produced by various processes. For this specification, methacrylate sheet shall be composed of polymerized acrylic monomers of which at least 808201;% shall be methyl methacrylate. Note 1:x00a0;This specification is intended to consolidate the requirements of the Cast Methacrylate Plastic Sheets portion of discontinued Fed. Spec. L-P-391D, discontinued Specification D702. Cast Methacrylate Plastic Sheets, Rods, Tubes and Shapes, and discontinued Specification D1547, Extruded Acrylic Plastic Sheet. 1.2x00a0;This specification is intended to cover acrylic sheet for general-purpose applications. For specialty applications consult the appropriate use standards. 1.3x00a0;The following safety hazards caveat pertains only to the test methods portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.4x00a0;Acrylic sheet is used frequently in applications in which extreme clarity, lack of optical distortion and absence of any foreign particulate matter are of primary significance. Reground material is suitable for use as long as careful control is used to eliminate adverse effects on these properties. The use of recycled material in type B-1 and B-2 sheet, is not suitable for use when these properties are adversely affected. The use of recycled or reground material is not possible for type A-1 and A-2 materials since the sheet is produced directly from monomer Note 2:x00a0;This standard and ISO 7823-1 address the same subject matter, but differ in technical content.
信息：ICS：83.140.10 CCS： 发布：2015 实施：
ASTM F484-08 与液体或半液体化合物接触的丙烯酸塑料应力开裂的标准试验方法
简介：
信息：ICS：83.080.10 CCS： 发布：2008-04-01 实施：
FORD WSB-M3G195-A-2006 汽车内部用双面压敏丙烯酸系树脂基胶带***与标准FORD WSS-M99P1111-A一起使用***
简介：
信息：ICS： CCS： 发布：2006-01-25 实施：
ASTM F3087-2015 医疗植入应用使用丙烯酸模制树脂的标准规格
简介：1.1x00a0;This specification covers acrylic resins supplied in virgin form (typically pellets, powder, or granules) for medical implant applications. The co-polymers are limited to random co-polymers. This specification provides requirements and associated test methods for this thermoplastic when it is intended for use in manufacturing implantable medical devices or components of medical devices. 1.1.1x00a0;While a variety of co-monomers may be used, the composition of the resin shall contain poly(methyl methacrylate) (PMMA) as its primary ingredient. Classification D788 defines an acrylic molding compound as x201c;having at least 70% of the polymer polymerized from methyl methacrylate.x201d; The terms PMMA and acrylic as used herein refer generically to both the homopolymer and to co-polymers as defined above. 1.2x00a0;As with any material, some characteristics may be altered by the processing techniques (such as molding, extrusion, machining, sterilization, and so forth) required for the production of a specific part or device. Therefore, properties of fabricated forms of this resin should be evaluated using test methods that are appropriate to ensure safety and efficacy as agreed upon between the supplier, purchaser, and regulating bodies. 1.3x00a0;This specification allows for designation of acrylic resins for all medical implant applications. The actual extent of performance and suitability for a specific application shall be evaluated by the medical device manufacturer and regulating bodies. 1.4x00a0;The properties included in this specification are those applicable for both unfilled acrylic polymers and for formulated resins containing barium sulfate. Indicated properties (Table 1 and Table X3.1) are for unfilled injection molded forms. Forms containing fillers other than barium sulfate, colorants, polymer blends that contain PMMA, or reclaimed materials are not covered by this specification. 1.5x00a0;Compliance with this specification does not obviate the need for functional testing of any device fabricated from the resin to demonstrate effectiveness in its intended application. 1.6x00a0;The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.7x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS： CCS： 发布：2015 实施：
FORD ESZ-M99J350-A-2008 聚酯底涂层/透明涂层低温烘干修复工艺用丙烯酸瓷漆用催化剂（马来酸）***与标准FORD WSS-M99P1111-A一起使用***
简介：
信息：ICS： CCS： 发布：2008 实施：
ASTM D3125-2006 测定无色单体丙烯酸酯和丙烯酸中氢醌的单甲基醚的标准试验方法
简介：Acrylic acid and its esters are normally inhibited with MEHQ only. This procedure presents a rapid and accurate method of determining the MEHQ content of fresh acrylic acid and acrylate esters in the absence of other inhibitors. MEHQ effectiveness may decline with age and this decline in effectiveness may not be indicated by this test method.1.1 This test method covers the determination of monomethyl ether of hydroquinone (MEHQ) in colorless monomeric acrylate esters and acrylic acid. The test method is applicable to the determination of MEHQ in the concentration range from 0 to 1200 parts per million.1.2 For purposes of determining conformance of an observed or a calculated value using this test method to relevant specifications, test result(s) shall be rounded off "to the nearest unit" in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E 29.1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.4 For hazard information and guidance, see the supplier's Material Safety Data Sheet.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of whoever uses this standard to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 8.
信息：ICS：71.080.60 (Alcohols. Ethers) CCS：G17 发布：2006 实施：
ASTM F2118-14 丙烯酸骨水泥材料力控制疲劳试验恒定振幅标准试验方法
简介：
信息：ICS：91.100.10 CCS： 发布：2014-12-01 实施：
FORD ESB-M4D9-A2-2007 丙烯酸系树脂成型料***与标准FORD WSS-M99P1111-A一起使用***
简介：
信息：ICS： CCS： 发布：2007-01-17 实施：
ASTM D3125-2006(2012) 测定无色丙烯酸酯和丙烯酸单体中氢醌单甲基醚的标准试验方法
简介：4. Significance and UseTop Bottom 4.1 Acrylic acid and its esters are normally inhibited with MEHQ only. This procedure presents a rapid and accurate method of determining the MEHQ content of fresh acrylic acid and acrylate esters in the absence of other inhibitors. 4.2 MEHQ effectiveness may decline with age and this decline in effectiveness may not be indicated by this test method. 1.1 This test method covers the determination of monomethyl ether of hydroquinone2 (MEHQ) in colorless monomeric acrylate esters and acrylic acid. The test method is applicable to the determination of MEHQ in the concentration range from 0 to 1200 parts per million. 1.2 For purposes of determining conformance of an observed or a calculated value using this test method to relevant specifications, test result(s) shall be rounded off ???to the nearest unit??? in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 For hazard information and guidance, see the supplierx0027;s Material Safety Data Sheet. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of whoever uses this standard to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 8.
信息：ICS：71.080.60 (Alcohols. Ethers) CCS：G17 发布：2006 实施：
ASTM F484-08(2013) 与液体或半液体化合物接触的丙烯酸塑料应力开裂的标准试验方法
简介：
信息：ICS：83.080.10 CCS： 发布：2013-12-01 实施：
ASTM D4094-2007 乙烯-丙烯酸酸性共聚物的酸含量的测定用标准试验方法
简介：1.1 This test method covers the determination of the acid content of ethylene-acrylic acid (EAA) copolymers containing 2.5 to 25 weight % of acrylic acid.1.2 The values stated in SI units are to be regarded as the standard. The values given in parenthesis are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific hazards statements are given in Section .Note 1There is no similar or equivalent ISO standard.
信息：ICS：83.080.20 (Thermoplastic materials) CCS：G32 发布：2007 实施：
FORD WSS-M70J12-A-2005 热固丙烯酸粉末状油漆***与标准FORD WSS-M99P1111-A一起使用***
简介：
信息：ICS： CCS： 发布：2005-09-28 实施：
ASTM D7733-2012 丙烯酸树脂分散体地面的标准规格
简介：1.1 This standard specifies test methods which measure minimum qualities for acrylic dispersion grounds. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：87.040 (Paints and varnishes) CCS：G32 发布：2012 实施：
FORD S-M32J110-B-2006 车外级金属丙烯酸磁漆***与标准FORD WSS-M99P1111-A一起使用***
简介：
信息：ICS： CCS： 发布：2006-09-07 实施：
FORD ESB-M99J228-C-2005 丙烯酸系树脂修复瓷漆用酸性催化剂（马来酸一丁酯/磷酸一丁酯的50/50混合物）***与标准FORD WSS-M99P1111-A一起使用***
简介：
信息：ICS： CCS： 发布：2005-09-13 实施：
ANSI/ASME PVHO-2-2012 载人压力容器安全性标准.载人压力容器(PVHO)丙烯酸窗体使用导则
简介：
信息：ICS：11.040.60;23.020.30 CCS：J74 发布：2012 实施：
FORD S-M32J110-C-2006 车外级金属丙烯酸磁漆***与标准FORD WSS-M99P1111-A一起使用***列于标准S-M32J110-B上
简介：
信息：ICS： CCS： 发布：2006-09-07 实施：
FORD ESB-M99J249-A-2005 汽车内部的第一面用彩饰层丙烯酸酸性油漆***与标准FORD WSS-M99P1111-A一起使用***
简介：
信息：ICS： CCS： 发布：2005-09-13 实施：
ASTM D7733-2012(2016) 丙烯酸分散地的标准规格
简介：1.1x00a0;This standard specifies test methods which measure minimum qualities for acrylic dispersion grounds. 1.2x00a0;The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：87.040 CCS： 发布：2012 实施：
FORD WSS-M96D30-A2-2006 IRHD硬度65耐发动机油的低压增强型乙烯/丙烯酸（AEM）橡胶软管***与标准FORD WSS-M99P1111-A一起使用***列于标准WSD-M96D30-A上
简介：
信息：ICS： CCS： 发布：2006-08-30 实施：
FORD ESB-M99J250-A-2005 汽车外部的第一面用彩饰层丙烯酸酸性油漆***与标准FORD WSS-M99P1111-A一起使用***
简介：
信息：ICS： CCS： 发布：2005-09-12 实施：
SAE AIR 5122A-2011 丙烯酸窗口术语和开裂验收标准
简介：This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. Compile a useful list of terms that are associated with acrylic window crazing and damage. Develop operator inspection, service life, and crazing acceptance criteria for acrylic windows.
信息：ICS：01.040.49;49.025.40 CCS：V13 发布：2011-11-07 实施：
FORD WSD-M96D30-A-2006 IRHD硬度75耐发动机油的低压增强型乙烯/丙烯酸（AEM）橡胶软管***与标准FORD WSS-M99P1111-A一起使用***
简介：
信息：ICS： CCS： 发布：2006-08-30 实施：
FORD ESB-M99J250-B-2005 汽车外部的第一面用彩饰层丙烯酸系树脂或聚碳酸酯塑性油漆***与标准FORD WSS-M99P1111-A一起使用***列于标准ESB-M99J250-A上
简介：
信息：ICS： CCS： 发布：2005-09-12 实施：
ASTM D6865-2011 丙烯腈 x2013; 苯乙烯 x2013; 丙烯酸盐(ASA)和丙烯腈 x2013; 三元乙丙 规范的标准分类系统和基础
简介：1.1 This classification system covers ASA and AES materials, and ASA and AES alloys suitable for injection molding and extrusion. This classification system does not cover recycled ASA and AES materials, and recycled ASA and AES alloys. 1.2 The properties included in this standard are those required to identify the compositions covered. Other requirements necessary to identify particular characteristics important to specialized applications are to be specified by using the suffixes as given in Section 5. 1.3 This classification system and subsequent line callout (specification) are intended to provide a means of calling out plastic materials used in the fabrication of end items or parts. It is not intended for the selection of materials. Material selection can be made by those having expertise in the plastic field only after careful consideration of the design and the performance required of the part, the environment to which it will be exposed, the fabrication process to be employed, the costs involved, and the inherent properties of the material other than those covered by this standard. 1.4 The following precautionary caveat pertains only to the test method portion, Section 11, of this classification system: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use. Note 18212;This classification system and ISO 6402 cover the same subject matter but are not technically equivalent.
信息：ICS：83.080.20 CCS：G35 发布：2011 实施：
FORD WSB-M3G222-A-2006 车内用高粘性耐紫外线丙烯酸系树脂双面涂布压敏粘合胶带***与标准FORD WSS-M99P111-A一起使用***
简介：
信息：ICS： CCS： 发布：2006-07-28 实施：
FORD ESF-M99J302-A-2005 保形丙烯酸涂料***与标准FORD WSS-M99P1111-A一起使用***
简介：
信息：ICS： CCS： 发布：2005-08-16 实施：
ASTM D5098-05a(2010) 艺术家丙烯酸分散涂料的标准规格
简介：
信息：ICS：87.040 CCS： 发布：2010-12-01 实施：
FORD WSS-M4D682-A6-2006 汽车内部用金属效果的具有极好高温耐受性的丙烯酸-苯乙烯-丙烯睛共聚物（ASA）+聚碳酸酯（PC）混合物成型料***与标准FORD WSS-M99P1111-A一起使用***
简介：
信息：ICS： CCS： 发布：2006-06-12 实施：
FORD ESB-M99J275-B-2005 汽车外部用丙烯酸类塑料的第一面热转印油漆***与标准FORD WSS-M99P1111-A一起使用***列于标准ESB-M99J274-B上
简介：
信息：ICS： CCS： 发布：2005-08-10 实施：
ASTM D4802-10 聚（甲基丙烯酸甲酯）丙烯酸塑料片的标准规格
简介：
信息：ICS：83.140.10 CCS： 发布：2010-07-01 实施：
ASTM D3125-06 无色单体丙烯酸酯和丙烯酸中氢醌单甲醚的标准试验方法
简介：
信息：ICS：71.080.60 CCS： 发布：2006-06-01 实施：
FORD ESB-M99J251-A-2005 汽车内部和外部的第二面用丙烯酸酸性油漆***与标准FORD WSS-M99P1111-A一起使用***列于标准ESB-M99J251-A2上
简介：
信息：ICS： CCS： 发布：2005-08-09 实施：
FORD ESB-M2G291-A-2010 聚氯乙烯挡风雨条用丙烯酸系树脂粘附底漆***与标准FORD WSS-M99P1111-A一起使用***
简介：
信息：ICS： CCS： 发布：2010-06-29 实施：
FORD WSB-M17H168-A-2006 可模压的聚丙烯（PP）/丙烯酸/聚酯针刺衬垫***与标准FORD WSS-M99P1111-A一起使用***使用标准WSS-M99P32-B
简介：
信息：ICS： CCS： 发布：2006-05-05 实施：
FORD ESB-M80J4-A-2005 透明丙烯酸系树脂部件用可紫外线固化的耐磨透明面漆***与标准FORD WSS-M99P1111-A一起使用***
简介：
信息：ICS： CCS： 发布：2005-07-29 实施：
我们的实力
部分实验仪器
合作客户
注意：因业务调整，暂不接受个人委托测试望见谅。
