金属剪切试验检测标准金属剪切试验-中析研究所检测

(CMA)

(CNAS)

(ISO)

(高新技术企业)

金属剪切试验相关标准参考信息

GB/T 7750-1987 胶粘剂拉伸剪切蠕变性能试验方法(金属对金属)
简介：本标准适用于测试在温度、拉伸剪切应力和时间的综合影响下，胶接金属与金属用的胶粘剂的蠕变性能。本标准适用的温度范围是室温至250℃。
信息：ICS：83.180 CCS：G38 发布：1987-05-25 实施：1987-12-01

ASTM D1002-10 用拉伸载荷（金属对金属）测定单搭接粘合金属试样表观剪切强度的标准试验方法
简介：
信息：ICS：83.180 CCS：发布：2010-10-01 实施：

ASTM D1002-01 用拉伸载荷（金属对金属）测定单搭接粘合金属试样表观剪切强度的标准试验方法
简介：
信息：ICS：83.180 CCS：发布：2001-10-10 实施：

GB 7750-1987 胶粘剂拉伸剪切蠕变性能试验方法 (金属对金属)
简介：
信息：ICS： CCS：G38 发布：1987-03-30 实施：1987-12-01

ASTM D1002-2010 用拉力负载测定金属之间胶粘剂抗剪切强度特性的标准试验方法
简介：This test method is primarily comparative. However, it does have application as a discriminator in determining variations in adherend surface preparation parameters and adhesive environmental durability. The test method has found applications in controlling surface preparations, primer, and adhesive systems for determining strength properties of tested systems. The misuse of strength values obtained from this test method as design-allowable stress values for structural joints could lead to product failure, property damage, and human injury. The apparent shear strength of an adhesive obtained from a given small single-lap specimen may differ from that obtained from a joint made with different adherends or by a different bonding process. The normal variation of temperature and moisture in the service environment causes the adherends and the adhesive to swell or shrink. The adherends and adhesive are likely to have different thermal and moisture coefficients of expansion. Even in small specimens, short-term environmental changes may induce internal stresses or chemical changes in the adhesive that permanently affect the apparent strength and other mechanical properties of the adhesive. The problem of predicting joint behavior in a changing environment is even more difficult if a different type of adherend is used in a larger structural joint than was used in the small specimen. The apparent shear strength measured with a single-lap specimen is not suitable for determining design-allowable stresses for designing structural joints that differ in any manner from the joints tested without thorough analysis and understanding of the joint and adhesive behaviors. Single-lap tests may be used for comparing and selecting adhesives or bonding processes for susceptibility to fatigue and environmental changes, but such comparisons must be made with great caution since different adhesives may respond differently in different joints. See Guide D4896 for further discussion of the concepts relative to interpretation of adhesive-bonded single-lap-joints.1.1 This test method covers the determination of the apparent shear strengths of adhesives for bonding metals when tested on a standard single-lap-joint specimen and under specified conditions of preparation and test. 1.2 The values stated in SI units are considered to be the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：23.040.50 CCS：G38 发布：2010 实施：

ASTM D5656-01 用于测定粘合剂在剪切下的应力 - 应变行为的厚粘附金属搭接剪切接头的标准试验方法
简介：
信息：ICS：83.180 CCS：发布：2001-10-10 实施：

T/CASAS 018-2021 微纳米金属烧结连接件剪切强度试验方法
简介：金属互连材料在半导体封装工业中占据关键地位。传统封装采用焊料合金互连，但其析出的金属间化合物导致互连层服役温度较低且脆性较高。作为最适合于第三代半导体模块封装的界面连接技术之一，以微纳米银、微纳米铜为代表的新型微纳米金属烧结互连技术具有组分单一、低工艺温度、高服役温度的优点，而且芯片连接件的可靠性也可以得到大幅提升。剪切强度作为微纳米金属烧结件主要的性能指标之一，其测试方法广受关注。因微纳米金属烧结技术尚属技术推广阶段，业内尚未针对使用该技术制备的烧结件制定专门的的剪切强度测试方法标准。传统焊料剪切强度较低，其测试方法标准和强度判定规则不再适用。同时，因行业内各单位的测试仪器型号不同，样品规格、测试条件、操作步骤等条件也各有不同，这使得产业内从业人员无法在统一的条件下比较微纳米金属烧结件的剪切强度性能。希望借此标准的制定，有效规范行业内测试方法，使得各测试参数可有效比对，助力微纳金属烧结技术的产业化发展。
信息：ICS：31.080.01 CCS：C397 发布：2021-11-01 实施：2021-11-04

ASTM D5656-2010 拉伸载荷法测定剪切胶粘剂应力-应变性能用的厚被粘物金属搭接-剪切接合标准试验方法
简介：This test method can be used to determine the stress-strain properties of an adhesive in shear and to establish the proportional-limit of the stress-stain relationship. This data may be useful for the design and analysis of adhesively bonded joints. This test method is not intended to determine adhesion characteristics of an adhesive to a particular substrate; rather this test method is intended to characterize the adhesive shear stress-strain properties that may be relevant for design considerations. This test method has been developed and applied using bonded aluminum adherends. At this time no assumptions regarding the validity of this test method with non-aluminum adherends can be made.1.1 This test method covers the preparation and testing of thick-adherend lap-shear samples for the determination of the stress-strain behavior of adhesives. 1.2 This test method covers data reduction and analysis of stress-strain curves obtained using thick-adherend lap-shear samples. 1.3 The values stated in SI units are to be regarded as the standard. The inch-pound units in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in 7.3.
信息：ICS：83.180 CCS：G38 发布：2010 实施：

ASTM D1002-99 用拉伸载荷（金属对金属）测定单搭接粘合金属试样表观剪切强度的标准试验方法
简介：
信息：ICS：83.180 CCS：发布：2001-10-10 实施：

ASTM D3166-99(2020) 通过拉伸载荷剪切胶粘剂疲劳性能的标准试验方法（金属/金属）
简介：
信息：ICS：83.180 CCS：发布：2020-01-01 实施：

ASTM D5656-2010(2017) 通过拉伸负载法测定胶粘剂剪切应力应变性能用厚粘附金属搭剪接头的标准试验方法
简介：5.1x00a0;This test method can be used to determine the stress-strain properties of an adhesive in shear and to establish the proportional-limit of the stress-stain relationship. This data may be useful for the design and analysis of adhesively bonded joints. 5.2x00a0;This test method is not intended to determine adhesion characteristics of an adhesive to a particular substrate; rather this test method is intended to characterize the adhesive shear stress-strain properties that may be relevant for design considerations. 5.3x00a0;This test method has been developed and applied using bonded aluminum adherends. At this time no assumptions regarding the validity of this test method with non-aluminum adherends can be made. 1.1x00a0;This test method covers the preparation and testing of thick-adherend lap-shear samples for the determination of the stress-strain behavior of adhesives. 1.2x00a0;This test method covers data reduction and analysis of stress-strain curves obtained using thick-adherend lap-shear samples. 1.3x00a0;The values stated in SI units are to be regarded as the standard. The inch-pound units in parentheses are for information only. 1.4x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in 7.3. 1.5x00a0;This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
信息：ICS：83.180 CCS：G38 发布：2010 实施：

ASTM D1002-2001 用拉力负载法测定单面搭接粘结金属试样的表面剪切强度的标准试验方法(金属之间)
简介：1.1 This test method covers the determination of the apparent shear strengths of adhesives for bonding metals when tested on a standard single-lap-joint specimen and under specified conditions of preparation and test.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.1.3 The values stated in SI units are considered to be the standard. The values given in parentheses are for information only.
信息：ICS：83.180 (Adhesives) CCS：G38 发布：2001 实施：

ASTM D1002-10(2019) 用拉伸载荷（金属对金属）测定单搭接粘合金属试样表观剪切强度的标准试验方法
简介：
信息：ICS：83.180 CCS：发布：2019-04-01 实施：

ASTM D2295-96(2008) 高温下拉伸载荷剪切粘合剂强度性能的标准试验方法（金属对金属）
简介：
信息：ICS：83.180 CCS：发布：2008-04-01 实施：

ASTM F1160-00e1 磷酸钙和金属医用复合磷酸钙/金属涂层的剪切和弯曲疲劳试验标准试验方法
简介：
信息：ICS：25.220.40 CCS：发布：2000-11-10 实施：

ASTM F1044-05(2017)e1 磷酸钙涂层和金属涂层剪切试验的标准试验方法
简介：
信息：ICS：25.220.40 CCS：发布：2017-12-01 实施：

ASTM D2293-96(2008) 通过压缩载荷剪切粘合剂蠕变性能的标准试验方法（金属对金属）
简介：
信息：ICS：83.180 CCS：发布：2008-04-01 实施：

ASTM F1160-00 磷酸钙和金属医用复合磷酸钙/金属涂层的剪切和弯曲疲劳试验标准试验方法
简介：
信息：ICS： CCS：发布：2000-11-10 实施：

ASTM F1160-14(2017)e1 磷酸钙和金属医用复合磷酸钙/金属涂层的剪切和弯曲疲劳试验标准试验方法
简介：
信息：ICS：25.220.40 CCS：发布：2017-12-01 实施：

ASTM D1002-05 用拉伸载荷（金属对金属）测定单搭接粘合金属试样表观剪切强度的标准试验方法
简介：
信息：ICS：83.180 CCS：发布：2005-10-01 实施：

ASTM F1160-2000e1 磷酸钙、金属医用和合成磷酸钙/金属覆层的剪切和弯曲疲劳试验的标准试验方法
简介：1.1 This test method covers the procedure for determining the shear and bending fatigue performance of calcium phosphate coatings and of porous and nonporous metallic coatings and for determining the bending fatigue performance of metallic coatings oversprayed with calcium phosphate. This test method has been established based on plasma-sprayed titanium and plasma-sprayed hydroxylapatite coatings. The efficacy of this test method for other coatings has not been established. In the shear fatigue mode this test method evaluates the adhesive and cohesive properties of the coating on a metallic substrate. In the bending fatigue mode this test method evaluates both the adhesion of the coating as well as the effects that the coating may have on the substrate material. These methods are limited to testing in air at ambient temperature. These test methods are not intended for application in fatigue tests of components or devices; however, the test method which most closely replicates the actual loading configuration is preferred.1.2 The values stated in SI units are to be regarded as the standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：25.220.40 (Metallic coatings) CCS：H22 发布：2000 实施：

ASTM D5656-10(2017) 用于测定粘合剂在剪切下的应力 - 应变行为的厚粘附金属搭接剪切接头的标准试验方法
简介：
信息：ICS：83.180 CCS：发布：2017-11-15 实施：

ASTM D3166-99(2005) 通过拉伸载荷剪切胶粘剂疲劳性能的标准试验方法（金属/金属）
简介：
信息：ICS：83.180 CCS：发布：2005-04-01 实施：

ASTM F1160-2000 磷酸钙、金属医用和合成磷酸钙/金属覆层的剪切和弯曲疲劳试验的标准试验方法
简介：1.1 This test method covers the procedure for determining the shear and bending fatigue performance of calcium phosphate coatings and of porous and nonporous metallic coatings and for determining the bending fatigue performance of metallic coatings oversprayed with calcium phosphate. This test method has been established based on plasma-sprayed titanium and plasma-sprayed hydroxylapatite coatings. The efficacy of this test method for other coatings has not been established. In the shear fatigue mode this test method evaluates the adhesive and cohesive properties of the coating on a metallic substrate. In the bending fatigue mode this test method evaluates both the adhesion of the coating as well as the effects that the coating may have on the substrate material. These methods are limited to testing in air at ambient temperature. These test methods are not intended for application in fatigue tests of components or devices; however, the test method which most closely replicates the actual loading configuration is preferred.1.2 The values stated in SI units are to be regarded as the standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS： CCS：H22 发布：2000 实施：

ASTM D2293-96(2016) 通过压缩载荷剪切粘合剂蠕变性能的标准试验方法（金属对金属）
简介：
信息：ICS：83.180 CCS：发布：2016-05-01 实施：

ASTM F1044-05 磷酸钙涂层和金属涂层剪切试验的标准试验方法
简介：
信息：ICS：25.220.40 CCS：发布：2005-04-01 实施：

ASTM F1044-99 磷酸钙涂层和金属涂层剪切试验的标准试验方法
简介：
信息：ICS：25.220.40 CCS：发布：1999-10-10 实施：

ASTM D2295-96(2016) 高温下拉伸载荷剪切粘合剂强度性能的标准试验方法（金属对金属）
简介：
信息：ICS：83.180 CCS：发布：2016-05-01 实施：

ASTM F1160-05 磷酸钙和金属医用复合磷酸钙/金属涂层的剪切和弯曲疲劳试验标准试验方法
简介：
信息：ICS：25.220.40 CCS：发布：2005-04-01 实施：

ASTM D3166-99 通过拉伸载荷剪切胶粘剂疲劳性能的标准试验方法（金属/金属）
简介：
信息：ICS：83.180 CCS：发布：1999-05-10 实施：

YY/T 0988.12-2016 外科植入物涂层.第12部分:磷酸钙涂层和金属涂层剪切试验方法
简介：YY/T 0988的本部分规定了在室温条件下粘结在致密金属基体上的连续磷酸钙涂层和金属涂层的剪切试验方法。本部分用于评价在剪切形式下（平行于粘结平面方向上）涂层对基体的粘结程度或内部结合程度。本部分采用国际单位制（SI）。本部分并非试图对所涉及到的所有安全问题进行阐述，即便是那些与其使用有关的安全问题。确立适当的安全及健康规范，以及在应用前明确管理限制的适用性，是本部分的使用者自身的责任。
信息：ICS：11.040.40 CCS：C35 发布：2016-03-23 实施：2017-01-01

ASTM D1002-2005 用拉力负载法测定单面搭接粘结的金属试样表面剪切强度的标准试验方法(金属之间)
简介：This test method is primarily comparative. However, it does have application as a discriminator in determining variations in adherend surface preparation parameters and adhesive environmental durability. The test method has found applications in controlling surface preparations, primer, and adhesive systems for determining strength properties of tested systems. The misuse of strength values obtained from this test method as design-allowable stress values for structural joints could lead to product failure, property damage, and human injury. The apparent shear strength of an adhesive obtained from a given small single-lap specimen may differ from that obtained from a joint made with different adherends or by a different bonding process. The normal variation of temperature and moisture in the service environment causes the adherends and the adhesive to swell or shrink. The adherends and adhesive are likely to have different thermal and moisture coefficients of expansion. Even in small specimens, short-term environmental changes may induce internal stresses or chemical changes in the adhesive that permanently affect the apparent strength and other mechanical properties of the adhesive. The problem of predicting joint behavior in a changing environment is even more difficult if a different type of adherend is used in a larger structural joint than was used in the small specimen. The apparent shear strength measured with a single-lap specimen is not suitable for determining design-allowable stresses for designing structural joints that differ in any manner from the joints tested without thorough analysis and understanding of the joint and adhesive behaviors. Single-lap tests may be used for comparing and selecting adhesives or bonding processes for susceptibility to fatigue and environmental changes, but such comparisons must be made with great caution since different adhesives may respond differently in different joints. See Guide D 4896 for further discussion of the concepts relative to interpretation of adhesive-bonded single-lap-joints.1.1 This test method covers the determination of the apparent shear strengths of adhesives for bonding metals when tested on a standard single-lap-joint specimen and under specified conditions of preparation and test.1.2 The values stated in SI units are considered to be the standard. The values given in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：83.180 (Adhesives) CCS：J04 发布：2005 实施：

ASTM D1002-1999 用拉力负载法测定单面搭接粘结金属试样的表面剪切强度的标准试验方法(金属之间)
简介：1.1 This test method covers the determination of the apparent shear strengths of adhesives for bonding metals when tested on a standard single-lap-joint specimen and under specified conditions of preparation and test.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.1.3 The values stated in SI units are considered to be the standard. The values given in parentheses are for information only.
信息：ICS：83.180 (Adhesives) CCS：G38 发布：1999 实施：

YY/T 0988.13-2016 外科植入物涂层.第13部分:磷酸钙、金属和磷酸钙/金属复合涂层剪切和弯曲疲劳试验方法
简介：YY/T 0988的本部分包含了确定磷酸钙涂层、多孔和非多孔金属涂层剪切和弯曲疲劳性能的试验方法，也包含了确定覆盖有磷酸钙的金属涂层弯曲疲劳性能的试验方法。本部分是基于等离子喷涂的钛涂层和等离子喷涂羟基磷灰石涂层所建立。本部分尚未建立对于其他涂层的效果。在剪切疲劳模式下本试验方法评价了覆盖金属基体上涂层的粘结性和结合性。在弯曲疲劳模式下本部分评价了涂层的粘结性以及涂层对基体材料的影响。这些试验方法仅在室温下空气中进行。
信息：ICS：11.040.40 CCS：C35 发布：2016-03-23 实施：2017-01-01

ASTM F1044-2005(2011)e1 磷酸钙覆层和金属覆层剪切试验的标准试验方法
简介：The shear test method is recommended for shear testing of calcium phosphate and metallic/substrate combinations and can provide information on the adhesive or cohesive strength of coatings under a uniaxial shear stress. The test method may be useful for comparative evaluation of adhesive or cohesive strengths of a variety of types of coatings. Information developed using this test method may be useful for certain quality control and design purposes. The test method should not be considered to provide an intrinsic values for utilization directly in making calculations such as determining the ability of a coating to withstand specified environmental stresses. Processing variables, such as substrate preparation prior to coating, surface texture, coating technique variables or post-coating heat treatment, or heat may introduce a significant effect on the results of the shear test. The specimen being evaluated must be representative of the actual end-use coating.1.1 This test method covers shear testing of continuous calcium phosphate coatings and metallic coatings adhering to dense metal substrates at ambient temperatures. It assesses the degree of adhesion of coatings to substrates, or the internal cohesion of a coating in shear, parallel to the surface plane. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：25.220.40 CCS：A29 发布：2005 实施：

ASTM F1044-1999 磷酸钙覆层和金属覆层剪切试验的标准试验方法
简介：1.1 This test method covers shear testing of continuous calcium phosphate coatings and metallic coatings adhering to dense metal substrates at ambient temperatures. It assesses the degree of adhesion of coatings to substrates, or the internal cohesion of a coating in shear, parallel to the surface plane. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：25.220.40 (Metallic coatings) CCS：A29 发布：1999 实施：

ASTM F1160-14 磷酸钙和金属医用复合磷酸钙/金属涂层的剪切和弯曲疲劳试验标准试验方法
简介：
信息：ICS：25.220.40 CCS：发布：2014-06-01 实施：

ASTM F1160-2005(2011)e1 磷酸钙金属医用和合成磷酸钙金属覆层的剪切和弯曲疲劳试验的标准试验方法
简介：The shear and bending fatigue tests are used to determine the effect of variations in material, geometry, surface condition, stress, and so forth, on the fatigue resistance of coated metallic materials subjected to direct stress for up to 107 cycles. These tests may be used as a relative guide to the selection of coated materials for service under condition of repeated stress. In order that such basic fatigue data be comparable, reproducible, and can be correlated among laboratories, it is essential that uniform fatigue practices be established. The results of the fatigue test may be used for basic material property design. Actual components should not be tested using these test methods.1.1 This test method covers the procedure for determining the shear and bending fatigue performance of calcium phosphate coatings and of porous and nonporous metallic coatings and for determining the bending fatigue performance of metallic coatings oversprayed with calcium phosphate. This test method has been established based on plasma-sprayed titanium and plasma-sprayed hydroxylapatite coatings. The efficacy of this test method for other coatings has not been established. In the shear fatigue mode, this test method evaluates the adhesive and cohesive properties of the coating on a metallic substrate. In the bending fatigue mode, this test method evaluates both the adhesion of the coating as well as the effects that the coating may have on the substrate material. These methods are limited to testing in air at ambient temperature. These test methods are not intended for application in fatigue tests of components or devices; however, the test method which most closely replicates the actual loading configuration is preferred. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：25.220.40 (Metallic coatings) CCS：发布：2005 实施：

SY/T 0041-1997 管道防腐层与金属粘结的剪切强度试验方法
简介：本标准规定了一种测量管道防腐层与金属粘结的剪切强度的试验方法。本标准适用于在规定的制备和试验条件下，通过对标准的单面搭接试件的试验，测定管道防腐层与金属粘结的剪切强度。
信息：ICS：75-010 CCS：E04 发布：1997-12-31 实施：1998-07-01

ASTM F1160-2014 磷酸钙和医用金属与复合磷酸钙/金属涂层的剪切和弯曲疲劳试验的标准试验方法
简介：5.1x00a0;The shear and bending fatigue tests are used to determine the effect of variations in material, geometry, surface condition, stress, and so forth, on the fatigue resistance of coated metallic materials subjected to direct stress for up to 107 cycles. These tests may be used as a relative guide to the selection of coated materials for service under condition of repeated stress. 5.2x00a0;In order that such basic fatigue data be comparable, reproducible, and can be correlated among laboratories, it is essential that uniform fatigue practices be established. 5.3x00a0;The results of the fatigue test may be used for basic material property design. Actual components should not be tested using these test methods. 1.1x00a0;This test method covers the procedure for determining the shear and bending fatigue performance of calcium phosphate coatings and of porous and nonporous metallic coatings and for determining the bending fatigue performance of metallic coatings over sprayed with calcium phosphate. This test method has been established based on plasma-sprayed titanium and plasma-sprayed hydroxylapatite coatings. The efficacy of this test method for other coatings has not been established. In the shear fatigue mode, this test method evaluates the adhesive and cohesive properties of the coating on a metallic substrate. In the bending fatigue mode, this test method evaluates both the adhesion of the coating as well as the effects that the coating may have on the substrate material. These methods are limited to testing in air at ambient temperature. These test methods are not intended for application in fatigue tests of components or devices; however, the test method which most closely replicates the actual loading configuration is preferred. 1.2x00a0;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：25.220.40 (Metallic coatings) CCS：发布：2014 实施：

ASTM F1044-2005 磷酸钙覆层和金属覆层剪切试验的标准试验方法
简介：The shear test method is recommended for shear testing of calcium phosphate and metallic/substrate combinations and can provide information on the adhesive or cohesive strength of coatings under a uniaxial shear stress. The test method may be useful for comparative evaluation of adhesive or cohesive strengths of a variety of types of coatings. Information developed using this test method may be useful for certain quality control and design purposes. The test method should not be considered to provide an intrinsic values for utilization directly in making calculations such as determining the ability of a coating to withstand specified environmental stresses. Processing variables, such as substrate preparation prior to coating, surface texture, coating technique variables or post-coating heat treatment, or heat may introduce a significant effect on the results of the shear test. The specimen being evaluated must be representative of the actual end-use coating.1.1 This test method covers shear testing of continuous calcium phosphate coatings and metallic coatings adhering to dense metal substrates at ambient temperatures. It assesses the degree of adhesion of coatings to substrates, or the internal cohesion of a coating in shear, parallel to the surface plane.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：25.220.40 (Metallic coatings) CCS：A29 发布：2005 实施：

ASTM D2293-96(2002) 通过压缩载荷剪切粘合剂蠕变性能的标准试验方法（金属对金属）
简介：
信息：ICS：83.180 CCS：发布：1996-09-10 实施：

ASTM D3166-99(2012) 通过拉伸载荷剪切胶粘剂疲劳性能的标准试验方法（金属/金属）
简介：
信息：ICS：83.180 CCS：发布：2012-10-01 实施：

ASTM F1160-2005 磷酸钙、金属医用和合成磷酸钙/金属覆层的剪切和弯曲疲劳试验的标准试验方法
简介：The shear and bending fatigue tests are used to determine the effect of variations in material, geometry, surface condition, stress, and so forth, on the fatigue resistance of coated metallic materials subjected to direct stress for up to 107 cycles. These tests may be used as a relative guide to the selection of coated materials for service under condition of repeated stress. In order that such basic fatigue data be comparable, reproducible, and can be correlated among laboratories, it is essential that uniform fatigue practices be established. The results of the fatigue test may be used for basic material property design. Actual components should not be tested using these test methods.1.1 This test method covers the procedure for determining the shear and bending fatigue performance of calcium phosphate coatings and of porous and nonporous metallic coatings and for determining the bending fatigue performance of metallic coatings oversprayed with calcium phosphate. This test method has been established based on plasma-sprayed titanium and plasma-sprayed hydroxylapatite coatings. The efficacy of this test method for other coatings has not been established. In the shear fatigue mode, this test method evaluates the adhesive and cohesive properties of the coating on a metallic substrate. In the bending fatigue mode, this test method evaluates both the adhesion of the coating as well as the effects that the coating may have on the substrate material. These methods are limited to testing in air at ambient temperature. These test methods are not intended for application in fatigue tests of components or devices; however, the test method which most closely replicates the actual loading configuration is preferred.1.2 The values stated in SI units are to be regarded as the standard.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：25.220.40 (Metallic coatings) CCS：A29 发布：2005 实施：

ASTM D2295-96(2002) 高温下拉伸载荷剪切粘合剂强度性能的标准试验方法（金属对金属）
简介：
信息：ICS：83.180 CCS：发布：1996-09-10 实施：

SY/T 0041-2012 防腐涂料与金属黏结的剪切强度试验方法
简介：本标准规定了一种测量防腐涂料与金属黏结的剪切强度的试验方法。本标准适用于在规定的试件制备和试验条件下，通过对单面搭接标准试件的试验，测定防腐涂料与金属黏结的剪切强度。
信息：ICS：75.200 CCS：A29 发布：2012-08-23 实施：2012-12-01

ASTM D5656-04 用于测定粘合剂在剪切下的应力 - 应变行为的厚粘附金属搭接剪切接头的标准试验方法
简介：
信息：ICS：83.180 CCS：发布：2004-04-01 实施：

ASTM D2295-96 高温下拉伸载荷剪切粘合剂强度性能的标准试验方法（金属对金属）
简介：
信息：ICS： CCS：发布：1996-09-10 实施：

GOST 31615-2012 外科植入物.磷酸钙涂层和金属涂层剪切试验的标准试验方法
简介：
信息：ICS：11.040.40 CCS：发布：2012 实施：2015-01-01

ASTM D5656-04e1 用于测定粘合剂在剪切下的应力 - 应变行为的厚粘附金属搭接剪切接头的标准试验方法
简介：
信息：ICS：83.180 CCS：发布：2004-04-01 实施：

ASTM D2293-96 通过压缩载荷剪切粘合剂蠕变性能的标准试验方法（金属对金属）
简介：
信息：ICS： CCS：发布：1996-09-10 实施：

ASTM F1044-05(2011)e1 磷酸钙涂层和金属涂层剪切试验的标准试验方法
简介：
信息：ICS：25.220.40 CCS：发布：2011-10-01 实施：

ASTM D5656-2004e1 拉伸载荷法测定剪切中胶粘剂应力-应变性能用厚被粘物金属搭接-剪切接头的标准试验方法
简介：This test method can be used to determine the stress-strain properties of an adhesive in shear and to establish the proportional-limit of the stress-stain relationship. This data may be useful for the design and analysis of adhesively bonded joints. This test method is not intended to determine adhesion characteristics of an adhesive to a particular substrate; rather this test method is intended to characterize the adhesive shear stress-strain properties that may be relevant for design considerations. This test method has been developed and applied using bonded aluminum adherends. At this time no assumptions regarding the validity of this test method with non-aluminum adherends can be made.1.1 This test method covers the preparation and testing of thick-adherend lap-shear samples for the determination of the stress-strain behavior of adhesives.1.2 This test method covers data reduction and analysis of stress-strain curves obtained using thick-adherend lap-shear samples.1.3 The values stated in SI units are to be regarded as the standard. The inch-pound units in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in 7.3.
信息：ICS：83.180 (Adhesives) CCS：G38 发布：2004 实施：

ASTM D2295-1996(2016) 采用高温拉向载荷 (金属对金属) 测定剪切胶粘剂强度性能的标准试验方法
简介：4.1x00a0;Comparative strength of adhesive bonds at elevated temperatures allows for better selection of adhesives that must perform at temperatures above normal. This test method is useful in supplying such information. 1.1x00a0;This test method covers the determination of the comparative shear strengths of adhesives for bonding metals when tested on a standard specimen and under specified conditions of preparation and testing at elevated temperatures. 1.2x00a0;This test method is applicable to the temperature range from 315 to 850x00b0;C (600 to 1500x00b0;F). 1.3x00a0;The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：83.180 CCS：发布：1996 实施：

ASTM F1160-05(2011)e1 磷酸钙和金属医用复合磷酸钙/金属涂层的剪切和弯曲疲劳试验标准试验方法
简介：
信息：ICS：25.220.40 CCS：发布：2011-10-01 实施：

ASTM D5656-2004 拉伸载荷法测定剪切中胶粘剂应力-应变性能用厚被粘物金属搭接-剪切接头的标准试验方法
简介：1.1 This test method covers the preparation and testing of thick-adherend lap-shear samples for the determination of the stress-strain behavior of adhesives.1.2 This test method covers data reduction and analysis of stress-strain curves obtained using thick-adherend lap-shear samples.1.3 The values stated in SI units are to be regarded as the standard. The inch-pound units in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in .
信息：ICS：83.180 (Adhesives) CCS：G38 发布：2004 实施：

ASTM D2295-1996(2002) 高温下用拉力负荷法测定金属之间胶粘剂剪切强度的试验方法
简介：Comparative strength of adhesive bonds at elevated temperatures allows for better selection of adhesives that must perform at temperatures above normal. This test method is useful in supplying such information.1.1 This test method covers the determination of the comparative shear strengths of adhesives for bonding metals when tested on a standard specimen and under specified conditions of preparation and testing at elevated temperatures. 1.2 This test method is applicable to the temperature range from 315 to 850176C (600 to 1500176F). 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：83.180 (Adhesives) CCS：G38 发布：1996 实施：

ASTM D5656-95(2000) 用于测定粘合剂在剪切下的应力 - 应变行为的厚粘附金属搭接剪切接头的标准试验方法
简介：
信息：ICS：83.180 CCS：发布：2001-10-10 实施：

ASTM D2295-1996 高温下用拉力负荷法测定金属之间胶粘剂剪切强度的试验方法
简介：1.1 This test method covers the determination of the comparative shear strengths of adhesives for bonding metals when tested on a standard specimen and under specified conditions of preparation and testing at elevated temperatures. 1.2 This test method is applicable to the temperature range from 315 to 850176C (600 to 1500176F). 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS： CCS：G38 发布：1996 实施：