橡胶压缩试验方法检测标准
橡胶压缩试验方法相关标准参考信息
ASTM D6049-03(2022) 用平行板之间的压缩法测量未硫化原橡胶和橡胶化合物的粘性和弹性行为的橡胶性能的标准试验方法
简介：
信息：ICS：83.040.10 CCS： 发布：2022-10-01 实施：
ASTM D575-91(2007) 压缩橡胶性能的标准试验方法
简介：
信息：ICS：83.060 CCS： 发布：2007-05-01 实施：
ASTM D395-01 橡胶性能压缩套件的标准试验方法
简介：
信息：ICS：83.060 CCS： 发布：2001-05-10 实施：
ASTM D945-22 橡胶压缩或剪切性能的标准试验方法（机械示波器）
简介：
信息：ICS：83.060 CCS： 发布：2022-06-01 实施：
ASTM D623-07 橡胶性能的标准试验方法&8212；压缩过程中的发热和弯曲疲劳
简介：
信息：ICS：83.060 CCS： 发布：2007-05-01 实施：
ASTM D395-98 橡胶性能压缩套件的标准试验方法
简介：
信息：ICS：83.060 CCS： 发布：2001-05-10 实施：
ASTM D623-07(2019)e1 压缩过程中橡胶性能发热和挠曲疲劳的标准试验方法
简介：
信息：ICS：83.060 CCS： 发布：2019-11-01 实施：
ASTM D623-2007(2014) 橡胶特性 - 压缩中热的产生及挠曲疲劳的标准试验方法
简介：4.1x00a0;Because of wide variations in service conditions, no correlation between these accelerated tests and service performance is given or implied. However, the test methods yield data that can be used to estimate relative service quality of different compounds. They are often applicable to research and development studies. 1.1x00a0;These test methods may be used to compare the fatigue characteristics and rate of heat generation of different rubber vulcanizates when they are subjected to dynamic compressive strains. 1.2x00a0;The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：83.060 (Rubber) CCS：G40 发布：2007 实施：
ASTM D575-91(2001) 压缩橡胶性能的标准试验方法
简介：
信息：ICS：83.060 CCS： 发布：2001-01-01 实施：
ASTM D623-07(2019) 橡胶性能的标准试验方法&x2014；压缩过程中的发热和弯曲疲劳
简介：
信息：ICS：83.060 CCS： 发布：2019-11-01 实施：
ASTM D623-2007 橡胶性能的标准试验方法.压缩发热和弯曲疲劳试验
简介：Because of wide variations in service conditions, no correlation between these accelerated tests and service performance is given or implied. However, the test methods yield data that can be used to estimate relative service quality of different compounds. They are often applicable to research and development studies.1.1 These test methods may be used to compare the fatigue characteristics and rate of heat generation of different rubber vulcanizates when they are subjected to dynamic compressive strains.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：83.060 (Rubber) CCS：G34 发布：2007 实施：
ASTM D575-91(1996) 压缩橡胶性能的标准试验方法
简介：
信息：ICS： CCS： 发布：2001-01-01 实施：
ASTM D1229-03(2019) 橡胶性能的标准试验方法&x2014；低温压缩永久变形
简介：
信息：ICS：83.060 CCS： 发布：2019-11-01 实施：
ASTM D945-06 压缩或剪切橡胶性能的标准试验方法（机械示波器）
简介：
信息：ICS： CCS： 发布：2006-07-01 实施：
ASTM D395-2001 橡胶压缩永久变形特性的标准试验方法
简介：1.1 These test methods cover the testing of rubber intended for use in applications in which the rubber will be subjected to compressive stresses in air or liquid media. They are applicable particularly to the rubber used in machinery mountings, vibration dampers, and seals. Two test methods are covered as follows:Test MethodSectionA-Compression Set Under Constant Force in Air7-10B-Compression Set Under Constant Deflection in Air11-141.2 The choice of test method is optional, but consideration should be given to the nature of the service for which correlation of test results may be sought. Unless otherwise stated in a detailed specification, Test Method B shall be used.1.3 Test Method B is not suitable for vulcanizates harder than 90 IRHD.1.4 The values stated in SI units are to be regarded as the standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：83.060 (Rubber) CCS：G34 发布：2001 实施：
ASTM D395-18 橡胶性能的标准试验方法&x2014；压缩永久变形
简介：
信息：ICS：83.060 CCS： 发布：2018-07-01 实施：
ASTM D945-2006 在压缩应力和剪切应力下橡胶特性的试验方法（机械示波器）
简介：The rubber properties that are measurable by these test methods are important for the isolation and absorption of shock and vibration. These properties may be used for quality control, development and research. Measurements in compression are influenced by specimen shape. This shape factor may be described as the ratio of the loaded surface area to the unloaded surface area. In applying data from a compression specimen, shape factor must be incorporated into the mathematical transferal to the application.1.1 These test methods cover the use of the Yerzley mechanical oscillograph for measuring mechanical properties of rubber vulcanizates in the generally small range of deformation that characterizes many technical applications. These properties include resilience, dynamic modulus, static modulus, kinetic energy, creep, and set under a given force. Measurements in compression and shear are described.,1.2 The test is applicable primarily, but not exclusively, to materials having static moduli at the test temperature such that forces below 2 MPa (280 psi) in compression or 1 MPa (140 psi) in shear will produce 20 % deformation, and having resilience such that at least three complete cycles are produced when obtaining the damped oscillatory curve. The range may be extended, however, by use of supplementary masses and refined methods of analysis. Materials may be compared either under comparable mean stress or mean strain conditions.1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For a specific warning see .
信息：ICS： CCS：G34 发布：2006 实施：
ASTM D531-2000(2010) 普西和琼斯橡胶压缩的标准试验方法
简介：The Pusey and Jones indentation value is the depth of indentation, expressed in hundredths of a millimetre, of a ball 3.175 mm (0.1250 in.) in diameter under an expressed force of 9.8 N (2.2 lbf). This value may be used to compare the indentation resistance of rubber and rubber-like materials. The indentation value obtained should not be confused with hardness as measured by Test Method D1415, since in the latter test the rubber immediately adjacent to the indentor is precompressed.1.1 This test method covers the determination of the indentation of rubber or rubber-like materials by means of the Pusey and Jones type of plastometer. This apparatus is used to measure the depth of indentation of an indentor, under fixed force into the surface of a specimen. 1.2 The values stated in SI units are to be regarded as the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：83.060 (Rubber) CCS：G34 发布：2000 实施：
ASTM D575-91(2018) 压缩橡胶性能的标准试验方法
简介：
信息：ICS：83.060 CCS： 发布：2018-06-01 实施：
ASTM D945-2006(2012) 在压缩应力和剪切应力下橡胶特性的标准试验方法(机械示波器)
简介：5.1x00a0;The rubber properties that are measurable by these test methods are important for the isolation and absorption of shock and vibration. These properties may be used for quality control, development and research. 5.2x00a0;Measurements in compression are influenced by specimen shape. This shape factor may be described as the ratio of the loaded surface area to the unloaded surface area. In applying data from a compression specimen, shape factor must be incorporated into the mathematical transferal to the application. 1.1x00a0;These test methods cover the use of the Yerzley mechanical oscillograph for measuring mechanical properties of rubber vulcanizates in the generally small range of deformation that characterizes many technical applications. These properties include resilience, dynamic modulus, static modulus, kinetic energy, creep, and set under a given force. Measurements in compression and shear are described.2,3 1.2x00a0;The test is applicable primarily, but not exclusively, to materials having static moduli at the test temperature such that forces below 2 MPa (280 psi) in compression or 1 MPa (1408201;psi) in shear will produce 208201;% deformation, and having resilience such that at least three complete cycles are produced when obtaining the damped oscillatory curve. The range may be extended, however, by use of supplementary masses and refined methods of analysis. Materials may be compared either under comparable mean stress or mean strain conditions. 1.3x00a0;The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For a specific warning see 12.14.
信息：ICS：83.060 (Rubber) CCS：G34 发布：2006 实施：
ASTM D623-99 压缩过程中橡胶性能发热和挠曲疲劳的标准试验方法
简介：
信息：ICS：83.060 CCS： 发布：1999-11-10 实施：
ASTM D6049-03(2017) 橡胶性能的标准试验方法&x2014；用平行板间压缩法测量未硫化生橡胶和橡胶化合物的粘性和弹性行为
简介：
信息：ICS：83.040.10 CCS： 发布：2017-10-01 实施：
ASTM D395-03 橡胶性能的标准试验方法&8212；压缩永久变形
简介：
信息：ICS： CCS： 发布：2003-08-10 实施：
ASTM D623-99e1 压缩过程中橡胶性能发热和挠曲疲劳的标准试验方法
简介：
信息：ICS：83.060 CCS： 发布：1999-11-10 实施：
ASTM D945-16 压缩或剪切橡胶性能的标准试验方法（机械示波器）
简介：
信息：ICS：83.060 CCS： 发布：2016-07-01 实施：
ASTM D6049-03 橡胶性能的标准试验方法&8212；用平行板间压缩法测量未硫化生橡胶和橡胶化合物的粘性和弹性行为
简介：
信息：ICS：83.040.10 CCS： 发布：2003-06-10 实施：
ASTM D623-1999e1 橡胶性能标准试验方法.压缩中热的产生和弯曲疲劳试验
简介：1.1 These test methods may be used to compare the fatigue characteristics and rate of heat generation of different rubber vulcanizates when they are subjected to dynamic compressive strains. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：83.060 (Rubber) CCS：G34 发布：1999 实施：
ASTM D395-16e1 橡胶性能的标准试验方法&x2014；压缩永久变形
简介：
信息：ICS：83.060 CCS： 发布：2016-04-15 实施：
ASTM D1229-03 橡胶性能的标准试验方法&8212；低温压缩永久变形
简介：
信息：ICS：83.060 CCS： 发布：2003-02-10 实施：
ASTM D623-1999 橡胶性能标准试验方法.压缩中热的产生和弯曲疲劳试验
简介：1.1 These test methods may be used to compare the fatigue characteristics and rate of heat generation of different rubber vulcanizates when they are subjected to dynamic compressive strains. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：83.060 (Rubber) CCS：G34 发布：1999 实施：
ASTM D395-16 橡胶性能的标准试验方法&x2014；压缩永久变形
简介：
信息：ICS：83.060 CCS： 发布：2016-04-15 实施：
ASTM D6049-2003(2008) 通过平行板之间压缩的橡胶化合物和非含硫生橡胶黏性和弹性的橡胶特性测定的标准试验方法
简介：The viscous and elastic behavior of unvulcanized rubbers and rubber compounds is of paramount importance in rubber manufacturing, since it affects processing, such as mixing, calendering, extrusion, and molding. The uniformity of these properties is equally important, as fluctuations will cause upsets in manufacturing processes. A test capable of measuring viscosity and elasticity of unvulcanized rubbers and rubber compounds, including their uniformity and prediction of processing behavior, is therefore highly desirable (see Practice D 6048 for further information). Compared to many other rheological tests, this test method measures viscosity and elasticity related parameters under conditions of low shear and has a high discriminating power. It can detect small rheological differences. A full discussion of the principles behind stress relaxation testing is given in Practice D 6048. Test results of this test method may be useful in predicting processability, but correlation with actual manufacturing processes must be established in each individual case, since conditions vary too widely. This test method is suitable for specification compliance testing, quality control, referee purposes, and research and development work.1. Scope 1.1 This test method is an adaptation of the German Standard DIN 53514, a further development of the former "Defo Test" (see ).1.2 This test method is capable of measuring and characterizing the rheological behavior (viscosity and elasticity) of unvulcanized raw rubbers and rubber compounds, relating to the macro structure of rubber polymers (average molecular weight, molecular weight distribution, long chain branching, and micro- and macro-gel).1.3 The viscosity and elasticity of unvulcanized rubbers and rubber compounds are determined by subjecting cylindrical test pieces to a compression/recovery cycle. The dependency on shear rate at constant shear stress is evaluated and the material fatigue behavior is determined in repeat cycle testing.1.4 The non-Newtonian viscous and elastic behavior of rubbers and rubber compounds can also be evaluated.1.5 Statistical evaluation of the test data provides an indication of data variation, which may be employed as an estimate of the homogeneity of the material tested.1.6 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only.1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：83.040.10 (Latex and raw rubber) CCS：G34 发布：2003 实施：
ASTM D395-1998 橡胶压缩永久变形特性的标准试验方法
简介：1.1 These test methods cover the testing of rubber intended for use in applications in which the rubber will be subjected to compressive stresses in air or liquid media. They are applicable particularly to the rubber used in machinery mountings, vibration dampers, and seals. Two test methods are covered as follows:Test MethodSectionA-Compression Set Under Constant Force in Air7-10B-Compression Set Under Constant Deflection in Air11-141.2 The choice of test method is optional, but consideration should be given to the nature of the service for which correlation of test results may be sought. Unless otherwise stated in a detailed specification, Test Method B shall be used.1.3 Test Method B is not suitable for vulcanizates harder than 90 IRHD.1.4 The values stated in SI units are to be regarded as the standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：83.060 (Rubber) CCS：G34 发布：1998 实施：
ASTM D395-2016 橡胶压缩永久变形特性的标准试验方法
简介：4.1x00a0;Compression set tests are intended to measure the ability of rubber compounds to retain elastic properties after prolonged action of compressive stresses. The actual stressing service may involve the maintenance of a definite deflection, the constant application of a known force, or the rapidly repeated deformation and recovery resulting from intermittent compressive forces. Though the latter dynamic stressing, like the others, produces compression set, its effects as a whole are simulated more closely by compression flexing or hysteresis tests. Therefore, compression set tests are considered to be mainly applicable to service conditions involving static stresses. Tests are frequently conducted at elevated temperatures. 1.1x00a0;These test methods cover the testing of rubber intended for use in applications in which the rubber will be subjected to compressive stresses in air or liquid media. They are applicable particularly to the rubber used in machinery mountings, vibration dampers, and seals. Two test methods are covered as follows: Test Method Section x00a0; Ax2014;Compression Set Under Constant Force in Air 8 x2013; 11 Bx2014;Compression Set Under Constant Deflection in Air 12 x2013; 15 Cx2014;Compression Set Under Constant Deflection in Air Considering Material Hardness 16 x2013; 21 1.2x00a0;The choice of test method is optional, but consideration should be given to the nature of the service for which correlation of test results may be sought. Unless otherwise stated in a detailed specification, Test Method B shall be used. 1.3x00a0;Test Method B is not suitable for vulcanizates harder than 90 IRHD. 1.4x00a0;The values stated in SI units are to be regarded as the standard.
信息：ICS：83.060 CCS： 发布：2016 实施：
ASTM D1229-2003(2008) 橡胶特性.在低温时压缩率的标准试验方法
简介：Rubber products, such as hydraulic seals on aircraft, submarine hatch gaskets, and hydraulic brake cups, may be exposed to varying temperature extremes. This test method provides a means of determining the extent to which recovery from compression at normal ambient temperatures is inhibited upon release of the compressive force during subsequent exposure at low temperatures.1.1 This test method covers evaluation of the ability of vulcanized rubbers that have been compressed at room temperature and then subjected to low temperature (air or carbon dioxide atmosphere), to recover from deformation when taken from the clamping device while still at the low temperature.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：83.060 (Rubber) CCS：G34 发布：2003 实施：
ASTM D1229-87(1997)e1 低温下橡胶性能压缩永久变形的标准试验方法
简介：
信息：ICS：83.060 CCS： 发布：1997-05-10 实施：
ASTM D395-15 橡胶性能的标准试验方法&x2014；压缩永久变形
简介：
信息：ICS：83.060 CCS： 发布：2015-08-01 实施：
ASTM D395-2003(2008) 橡胶特性.压缩形变的标准试验方法
简介：Compression set tests are intended to measure the ability of rubber compounds to retain elastic properties after prolonged action of compressive stresses. The actual stressing service may involve the maintenance of a definite deflection, the constant application of a known force, or the rapidly repeated deformation and recovery resulting from intermittent compressive forces. Though the latter dynamic stressing, like the others, produces compression set, its effects as a whole are simulated more closely by compression flexing or hysteresis tests. Therefore, compression set tests are considered to be mainly applicable to service conditions involving static stresses. Tests are frequently conducted at elevated temperatures.1.1 These test methods cover the testing of rubber intended for use in applications in which the rubber will be subjected to compressive stresses in air or liquid media. They are applicable particularly to the rubber used in machinery mountings, vibration dampers, and seals. Two test methods are covered as follows:Test MethodSectionA-Compression Set Under Constant Force in Air7-10B-Compression Set Under Constant Deflection in Air11-141.2 The choice of test method is optional, but consideration should be given to the nature of the service for which correlation of test results may be sought. Unless otherwise stated in a detailed specification, Test Method B shall be used.1.3 Test Method B is not suitable for vulcanizates harder than 90 IRHD.1.4 The values stated in SI units are to be regarded as the standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：83.060 (Rubber) CCS：G34 发布：2003 实施：
BS 903-A6-1992 橡胶的物理试验.第A6部分:室温、高温和低温下压缩变形的测定方法
简介：Methods for the determination of compression set characteristics of vulcanized or thermoplastic rubbers at ambient, elevated or low temperatures.
信息：ICS：83.060 CCS：G42 发布：1992-05-15 实施：1992-05-15
ASTM D1229-03(2015) 橡胶性能的标准试验方法&x2014；低温压缩永久变形
简介：
信息：ICS：83.060 CCS： 发布：2015-06-15 实施：
ASTM D1229-2003 橡胶特性的标准试验方法.低温时的压缩形变
简介：Rubber products, such as hydraulic seals on aircraft, submarine hatch gaskets, and hydraulic brake cups, may be exposed to varying temperature extremes. This test method provides a means of determining the extent to which recovery from compression at normal ambient temperatures is inhibited upon release of the compressive force during subsequent exposure at low temperatures.1.1 This test method covers evaluation of the ability of vulcanized rubbers that have been compressed at room temperature and then subjected to low temperature (air or carbon dioxide atmosphere), to recover from deformation when taken from the clamping device while still at the low temperature. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：83.060 (Rubber) CCS：G40 发布：2003 实施：
ASTM D945-92(2001)e1 压缩或剪切橡胶性能的标准试验方法（机械示波器）
简介：
信息：ICS：83.060 CCS： 发布：1992-03-15 实施：
ASTM D395-14 橡胶性能的标准试验方法&mdash；压缩永久变形
简介：
信息：ICS：83.060 CCS： 发布：2014-07-01 实施：
ASTM D1229-2003(2015) 橡胶特性的标准试验方法. 低温压缩永久变形
简介：4.1x00a0;Rubber products, such as hydraulic seals on aircraft, submarine hatch gaskets, and hydraulic brake cups, may be exposed to varying temperature extremes. This test method provides a means of determining the extent to which recovery from compression at normal ambient temperatures is inhibited upon release of the compressive force during subsequent exposure at low temperatures. 1.1x00a0;This test method covers evaluation of the ability of vulcanized rubbers that have been compressed at room temperature and then subjected to low temperature (air or carbon dioxide atmosphere), to recover from deformation when taken from the clamping device while still at the low temperature. 1.2x00a0;The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：83.060 CCS： 发布：2003 实施：
ASTM D945-92(1997) 压缩或剪切橡胶性能的标准试验方法（机械示波器）
简介：
信息：ICS： CCS： 发布：1992-03-15 实施：
ASTM D395-2014 橡胶压缩永久变形特性的标准试验方法
简介：4.1x00a0;Compression set tests are intended to measure the ability of rubber compounds to retain elastic properties after prolonged action of compressive stresses. The actual stressing service may involve the maintenance of a definite deflection, the constant application of a known force, or the rapidly repeated deformation and recovery resulting from intermittent compressive forces. Though the latter dynamic stressing, like the others, produces compression set, its effects as a whole are simulated more closely by compression flexing or hysteresis tests. Therefore, compression set tests are considered to be mainly applicable to service conditions involving static stresses. Tests are frequently conducted at elevated temperatures. 1.1x00a0;These test methods cover the testing of rubber intended for use in applications in which the rubber will be subjected to compressive stresses in air or liquid media. They are applicable particularly to the rubber used in machinery mountings, vibration dampers, and seals. Two test methods are covered as follows: Test Method Section x00a0; Ax2014;Compression Set Under Constant Force in Air 8199;7x2013;10 Bx2014;Compression Set Under Constant Deflection in Air 11x2013;14 1.2x00a0;The choice of test method is optional, but consideration should be given to the nature of the service for which correlation of test results may be sought. Unless otherwise stated in a detailed specification, Test Method B shall be used. 1.3x00a0;Test Method B is not suitable for vulcanizates harder than 90 IRHD. 1.4x00a0;The values stated in SI units are to be regarded as the standard. 1.5x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：83.060 (Rubber) CCS： 发布：2014 实施：
ASTM D6049-2003(2013) 通过平行板之间压缩测量未硫化生橡胶和橡胶化合物粘性和弹性的橡胶性能的标准试验方法
简介：5.1x00a0;The viscous and elastic behavior of unvulcanized rubbers and rubber compounds is of paramount importance in rubber manufacturing, since it affects processing, such as mixing, calendering, extrusion, and molding. The uniformity of these properties is equally important, as fluctuations will cause upsets in manufacturing processes. 5.2x00a0;A test capable of measuring viscosity and elasticity of unvulcanized rubbers and rubber compounds, including their uniformity and prediction of processing behavior, is therefore highly desirable (see Practice D6048 for further information). 5.3x00a0;Compared to many other rheological tests, this test method measures viscosity and elasticity related parameters under conditions of low shear and has a high discriminating power. It can detect small rheological differences. A full discussion of the principles behind stress relaxation testing is given in Practice D6048. 5.4x00a0;Test results of this test method may be useful in predicting processability, but correlation with actual manufacturing processes must be established in each individual case, since conditions vary too widely. 5.5x00a0;This test method is suitable for specification compliance testing, quality control, referee purposes, and research and development work. 1.1x00a0;This test method is an adaptation of the German Standard DIN 53514, a further development of the former x201c;Defo Testx201d; (see Appendix X1). 1.2x00a0;This test method is capable of measuring and characterizing the rheological behavior (viscosity and elasticity) of unvulcanized raw rubbers and rubber compounds, relating to the macro structure of rubber polymers (average molecular weight, molecular weight distribution, long chain branching, and micro- and macro-gel). 1.3x00a0;The viscosity and elasticity of unvulcanized rubbers and rubber compounds are determined by subjecting cylindrical test pieces to a compression/recovery cycle. The dependency on shear rate at constant shear stress is evaluated and the material fatigue behavior is determined in repeat cycle testing. 1.4x00a0;The non-Newtonian viscous and elastic behavior of rubbers and rubber compounds can also be evaluated. 1.5x00a0;Statistical evaluation of the test data provides an indication of data variation, which may be employed as an estimate of the homogeneity of the material tested. 1.6x00a0;The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only. 1.7x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：83.040.10 (Latex and raw rubber) CCS：G40 发布：2003 实施：
ASTM D945-1992(2001)e1 用机械示波器测定在压缩应力和剪切应力下橡胶特性的试验方法
简介：1.1 These test methods cover the use of the Yerzley mechanical oscillograph for measuring mechanical properties of rubber vulcanizates in the generally small range of deformation that characterizes many technical applications. These properties include resilience, dynamic modulus, static modulus, kinetic energy, creep, and set under a given force. Measurements in compression and shear are described.1.2 The test is applicable primarily, but not exclusively, to materials having static moduli at the test temperature such that forces below 2 MPa (280 psi) in compression or 1 MPa (140 psi) in shear will produce 20 % deformation, and having resilience such that at least three complete cycles are produced when obtaining the damped oscillatory curve. The range may be extended, however, by use of supplementary masses and refined methods of analysis. Materials may be compared either under comparable mean stress or mean strain conditions.1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statement see 12.14.
信息：ICS：83.060 (Rubber) CCS：G34 发布：1992 实施：
ASTM D945-06(2012) 压缩或剪切橡胶性能的标准试验方法（机械示波器）
简介：
信息：ICS：83.060 CCS： 发布：2012-12-01 实施：
ASTM D6049-2003(2017) 通过平行板之间压缩的橡胶化合物和非含硫生橡胶黏性和弹性的橡胶特性测定的标准试验方法
简介：5.1x00a0;The viscous and elastic behavior of unvulcanized rubbers and rubber compounds is of paramount importance in rubber manufacturing, since it affects processing, such as mixing, calendering, extrusion, and molding. The uniformity of these properties is equally important, as fluctuations will cause upsets in manufacturing processes. 5.2x00a0;A test capable of measuring viscosity and elasticity of unvulcanized rubbers and rubber compounds, including their uniformity and prediction of processing behavior, is therefore highly desirable (see Practice D6048 for further information). 5.3x00a0;Compared to many other rheological tests, this test method measures viscosity and elasticity related parameters under conditions of low shear and has a high discriminating power. It can detect small rheological differences. A full discussion of the principles behind stress relaxation testing is given in Practice D6048. 5.4x00a0;Test results of this test method may be useful in predicting processability, but correlation with actual manufacturing processes must be established in each individual case, since conditions vary too widely. 5.5x00a0;This test method is suitable for specification compliance testing, quality control, referee purposes, and research and development work. 1.1x00a0;This test method is an adaptation of the German Standard DIN 53514, a further development of the former x201c;Defo Testx201d; (see Appendix X1). 1.2x00a0;This test method is capable of measuring and characterizing the rheological behavior (viscosity and elasticity) of unvulcanized raw rubbers and rubber compounds, relating to the macro structure of rubber polymers (average molecular weight, molecular weight distribution, long chain branching, and micro- and macro-gel). 1.3x00a0;The viscosity and elasticity of unvulcanized rubbers and rubber compounds are determined by subjecting cylindrical test pieces to a compression/recovery cycle. The dependency on shear rate at constant shear stress is evaluated and the material fatigue behavior is determined in repeat cycle testing. 1.4x00a0;The non-Newtonian viscous and elastic behavior of rubbers and rubber compounds can also be evaluated. 1.5x00a0;Statistical evaluation of the test data provides an indication of data variation, which may be employed as an estimate of the homogeneity of the material tested. 1.6x00a0;The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only. 1.7x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices ......
信息：ICS：83.040.10 CCS：G34 发布：2003 实施：
ASTM D945-1992(1997) 用机械示波器测定在压缩应力和剪切应力下橡胶特性的试验方法
简介：1.1 These test methods cover the use of the Yerzley mechanical oscillograph for measuring mechanical properties of rubber vulcanizates in the generally small range of deformation that characterizes many technical applications. These properties include resilience, dynamic modulus, static modulus, kinetic energy, creep, and set under a given force. Measurements in compression and shear are described.1.2 The test is applicable primarily, but not exclusively, to materials having static moduli at the test temperature such that forces below 2 MPa (280 psi) in compression or 1 MPa (140 psi) in shear will produce 20 % deformation, and having resilience such that at least three complete cycles are produced when obtaining the damped oscillatory curve. The range may be extended, however, by use of supplementary masses and refined methods of analysis. Materials may be compared either under comparable mean stress or mean strain conditions.1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statement see 12.14.
信息：ICS： CCS：G34 发布：1992 实施：
ASTM D575-91(2012) 压缩橡胶性能的标准试验方法
简介：
信息：ICS：83.060 CCS： 发布：2012-01-01 实施：
ASTM D395-2003 橡胶特性的标准试验方法.压缩形变
简介：Compression set tests are intended to measure the ability of rubber compounds to retain elastic properties after prolonged action of compressive stresses. The actual stressing service may involve the maintenance of a definite deflection, the constant application of a known force, or the rapidly repeated deformation and recovery resulting from intermittent compressive forces. Though the latter dynamic stressing, like the others, produces compression set, its effects as a whole are simulated more closely by compression flexing or hysteresis tests. Therefore, compression set tests are considered to be mainly applicable to service conditions involving static stresses. Tests are frequently conducted at elevated temperatures.1.1 These test methods cover the testing of rubber intended for use in applications in which the rubber will be subjected to compressive stresses in air or liquid media. They are applicable particularly to the rubber used in machinery mountings, vibration dampers, and seals. Two test methods are covered as follows:Test MethodSectionA-Compression Set Under Constant Force in Air7-10B-Compression Set Under Constant Deflection in Air11-141.2 The choice of test method is optional, but consideration should be given to the nature of the service for which correlation of test results may be sought. Unless otherwise stated in a detailed specification, Test Method B shall be used.1.3 Test Method B is not suitable for vulcanizates harder than 90 IRHD.1.4 The values stated in SI units are to be regarded as the standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS： CCS：G34 发布：2003 实施：
BS 5293-19-1991 橡胶工业用炭黑的取样和试验方法.用于测定邻苯二甲酸二丁酯吸收数的样品制备(压缩样品)
简介：Two procedures using different types of compression cylinders and pistons. Dry carbon black is compressed four times at a pressure of 165 MPa.
信息：ICS：83.040.20 CCS：G49 发布：1991-10-31 实施：1991-10-31
ASTM D1229-03(2008) 低温下橡胶性能压缩永久变形的标准试验方法
简介：
信息：ICS：83.060 CCS： 发布：2008-05-01 实施：
ASTM D395-02 橡胶性能的标准试验方法&8212；压缩永久变形
简介：
信息：ICS：83.060 CCS： 发布：2002-12-10 实施：
ASTM D575-1991(2012) 橡胶压缩特性的标准试验方法
简介：These test methods are useful in comparing stiffness of rubber materials in compression. They can be used by rubber technologists to aid in development of materials for compressive applications.1.1 These test methods cover two test procedures for determining the compression-deflection characteristics of rubber compounds other than those usually classified as hard rubber and sponge rubber. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：83.060 CCS：G40 发布：1991 实施：
ASTM D395-03(2008) 橡胶性能的标准试验方法&8212；压缩永久变形
简介：
信息：ICS：83.060 CCS： 发布：2008-05-01 实施：
ASTM D395-2002 橡胶压缩永久变形特性的标准试验方法
简介：1.1 These test methods cover the testing of rubber intended for use in applications in which the rubber will be subjected to compressive stresses in air or liquid media. They are applicable particularly to the rubber used in machinery mountings, vibration dampers, and seals. Two test methods are covered as follows:Test MethodSectionA-Compression Set Under Constant Force in Air7-10B-Compression Set Under Constant Deflection in Air11-141.2 The choice of test method is optional, but consideration should be given to the nature of the service for which correlation of test results may be sought. Unless otherwise stated in a detailed specification, Test Method B shall be used.1.3 Test Method B is not suitable for vulcanizates harder than 90 IRHD.1.4 The values stated in SI units are to be regarded as the standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：83.060 (Rubber) CCS：G34 发布：2002 实施：
ASTM D575-1991(2007) 橡胶压缩特性的标准试验方法
简介：These test methods are useful in comparing stiffness of rubber materials in compression. They can be used by rubber technologists to aid in development of materials for compressive applications.1.1 These test methods cover two test procedures for determining the compression-deflection characteristics of rubber compounds other than those usually classified as hard rubber and sponge rubber.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：83.060 (Rubber) CCS：G34 发布：1991 实施：
