热重分析仪在哪里的检测标准
热重分析仪在哪里的相关标准参考信息
GB/T 27761-2011 热重分析仪失重和剩余量的试验方法
简介：本标准规定了通过热重分析仪(TGA)来确认失重和剩余量的程序,并建立起基于失重和剩余量试验的分析方法。 本标准适用于确认热重分析仪性能参数,包括失重和剩余量的重复性(精密度)、检测限、定量限、线性与偏差,技术说明和规章符合性。 本标准不包括与其使用相关的所有安全问题。在使用本标准方法之前,使用者有责任建立适当的安全与健康规范,并确认规范的适用性。
信息：ICS：19.020 CCS：N04 发布：2011-12-30 实施：2012-05-01
ASTM E1582-10 热重分析仪的温度校准标准实践
简介：
信息：ICS：17.200.20 CCS： 发布：2010-04-01 实施：
ASTM D6375-1999a 用热重分析仪(TGA)Noack法测定润滑油蒸发损失的标准试验方法
简介：1.1 This test method covers the procedure for determining the Noack evaporation loss of lubricating oils using a thermogravimetric analyzer test (TGA). The test method is applicable to base stocks and fully formulated lubricant oils having a Noack evaporative loss ranging from 0 to 30 weight percent. This procedure requires much smaller specimens, and is faster, easier and safer than the standard Noack methods. 1.2 The evaporative loss determined by this test method is the same as that determined using the standard Noack test methods. 1.3 The values stated in SI units are to be regarded as the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：75.100 (Lubricants, industrial oils and related pr CCS：E34 发布：1999 实施：
GB/T 27762-2011 热重分析仪质量示值校准的试验方法
简介：本标准规定了热重分析仪质量示值校准的试验方法。 本标准适用于热重分析仪的质量/重量校准或性能确认,且适用于商业和定制设备。 本标准不包括与其使用相关的所有安全问题。在使用本标准方法之前,使用者有责任建立适当的安全与健康规范,并确认规范的适用性。
信息：ICS：19.020 CCS：N04 发布：2011-12-30 实施：2012-05-01
ASTM D6375-09 用热重分析仪（TGA）Noack法测定润滑油蒸发损失的标准试验方法
简介：
信息：ICS：75.100 CCS： 发布：2009-03-01 实施：
WJ 2292-1995 热重分析仪检定规程
简介：
信息：ICS： CCS：N11 发布：1995 实施：1995-09-01
ASTM E1582-21 热重分析仪温度校准的标准试验方法
简介：
信息：ICS：17.200.20 CCS： 发布：2021-07-01 实施：
ANSI/ASTM D6375-2009 用热重分析仪(TGA)测定润滑油蒸发损耗的试验方法(Noack法)
简介：
信息：ICS：75.100 CCS：E34 发布：2009 实施：
JB/T 6856-1993 热重—差热分析仪
简介：本标准规定了热重—差热分析仪（TG—DTA）的分类、技术要求、试验方法、检验规则、标志、包装、运输和贮存等。 本标准适用于常压中温类、常压高温类热重—差热分析仪。 本标准不适用于常低温类仪器。
信息：ICS：17.200.20 CCS：N11 发布：1993-07-09 实施：1994-01-01
ASTM E2551-20 热重分析仪用湿度发生器湿度校准（或构象）的标准试验方法
简介：
信息：ICS：71.040.40 CCS： 发布：2020-03-15 实施：
ASTM D6375-2009(2014) 用热重分析仪(TGA)测定润滑油蒸发损耗的标准试验方法(Noack法)
简介：5.1x00a0;This test method is a safe and fast alternative for determination of the Noack evaporation loss of a lubricant. 5.2x00a0;The evaporation loss of a lubricant is important in the hot zones of equipment where evaporation of part of the lubricant may increase lubricant consumption. 5.3x00a0;Some lubricant specifications cite a maximum allowable evaporative loss. 1.1x00a0;This test method covers the procedure for determining the Noack evaporation loss of lubricating oils using a thermogravimetric analyzer test (TGA). The test method is applicable to base stocks and fully formulated lubricant oils having a Noack evaporative loss ranging from 0 to 30 mass %. This procedure requires much smaller specimens, and is faster when multiple samples are sequentially analyzed, and safer than the standard Noack method using Woodx0027;s metal. 1.2x00a0;The evaporative loss determined by this test method is the same as that determined using the standard Noack test methods. 1.3x00a0;The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：75.100 (Lubricants, industrial oils and related pr CCS：E34 发布：2009 实施：
简介： 信息：
ASTM D6375-09(2019) 用热重分析仪（TGA）Noack法测定润滑油蒸发损失的标准试验方法
简介：
信息：ICS：75.100 CCS： 发布：2019-12-01 实施：
ASTM E2040-08 热重分析仪质谱校准的标准测试方法
简介：
信息：ICS：71.040.50 CCS： 发布：2008-09-01 实施：
简介： 信息：
ASTM E2040-19 热重分析仪质谱校准的标准测试方法
简介：
信息：ICS：19.020 CCS： 发布：2019-12-01 实施：
ASTM E2040-2008(2014) 热重分析仪质量刻度校准的标准试验方法
简介：5.1x00a0;This test method calibrates or demonstrates conformity of thermogravimetric apparatus at ambient conditions. Most thermogravimetry analysis experiments are carried out under temperature ramp conditions or at isothermal temperatures distant from ambient conditions. This test method does not address the temperature effects on mass calibration. 5.2x00a0;In most thermogravimetry experiments, the mass change is reported as weight percent in which the observed mass at any time during the course of the experiment is divided by the original mass of the test specimen. This method of reporting results assumes that the mass scale of the apparatus is linear with increasing mass. In such cases, it may be necessary only to confirm the performance of the instrument by comparison to a suitable reference. 5.3x00a0;When the actual mass of the test specimen is recorded, the use of a calibration factor to correct the calibration of the apparatus may be required, on rare occasions. 1.1x00a0;This test method describes the calibration or performance confirmation of the mass (or weight) scale of thermogravimetric analyzers and is applicable to commercial and custom-built apparatus. 1.2x00a0;The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3x00a0;There is no ISO standard equivalent to this test method. 1.4x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：71.040.50 (Physicochemical methods of analysis) CCS： 发布：2008 实施：
简介： 信息：
ISO 248-2-2019 橡胶 原料 - 挥发物含量的测定 - 第2部分:使用带有红外干燥装置的自动分析仪的热重分析方法
简介：
信息：ICS：83.040.10 CCS： 发布：2019-03-26 实施：
ASTM E2040-2008 热重分析仪质量刻度校准的标准试验方法
简介：This test method calibrates or demonstrates conformity of thermogravimetric apparatus at ambient conditions. Most thermogravimetry analysis experiments are carried out under temperature ramp conditions or at isothermal temperatures distant from ambient conditions. This test method does not address the temperature effects on mass calibration. In most thermogravimetry experiments, the mass change is reported as weight percent in which the observed mass at any time during the course of the experiment is divided by the original mass of the test specimen. This method of reporting results assumes that the mass scale of the apparatus is linear with increasing mass. In such cases, it may be necessary only to confirm the performance of the instrument by comparison to a suitable reference. When the actual mass of the test specimen is recorded, the use of a calibration factor to correct the calibration of the apparatus may be required, on rare occasions.1.1 This test method describes the calibration or performance confirmation of the mass (or weight) scale of thermogravimetric analyzers and is applicable to commercial and custom-built apparatus. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 There is no ISO standard equivalent to this test method. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：71.040.50 (Physicochemical methods of analysis) CCS：N11 发布：2008 实施：
简介： 信息：
ASTM E2551-18 热重分析仪用湿度发生器湿度校准（或构象）的标准试验方法
简介：
信息：ICS：71.040.40 CCS： 发布：2018-10-01 实施：
ASTM E2551-07 用于热重分析仪的湿度发生器的湿度校准（或构造）的标准测试方法
简介：
信息：ICS：71.040.40 CCS： 发布：2007-03-01 实施：
简介： 信息：
JB/T 6856-2017 热重-差热分析仪
简介：
信息：ICS： CCS： 发布：2018-01-01 实施：2018-01-01
ASTM E2551-2007 和热重分析仪一起使用的湿度发生器湿度校正(或构型)的标准试验方法
简介：This test method calibrates or demonstrates conformity of the humidity level in a purge gas generated by a humidity generator at a fixed temperature. Such calibration or demonstration of conformity may be required by quality initiatives. Conformance demonstrates that the humidified purge gas is within some established limits. Calibration provides an offset and or slope value that may be used for establishing the relative humidity scale of the apparatus.1.1 This test method describes the humidity calibration (or conformance) of humidity generators for use with thermogravimetric analyzers and other thermal analysis apparatus. The humidity range covered is 5 to 95 % relative humidity (%RH) and the temperature range is 0 to 80 176;C.1.2 The values stated in SI units are to be regarded as the standard.1.3 There are no ISO equivalents to this standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：71.040.40 (Chemical analysis) CCS：A43 发布：2007 实施：
简介： 信息：
ASTM E1582-17 热重分析仪的温度校准的标准测试方法
简介：
信息：ICS：17.200.20 CCS： 发布：2017-10-01 实施：
ASTM D6375-05 用热重分析仪（TGA）Noack法测定润滑油蒸发损失的标准试验方法
简介：
信息：ICS：75.100 CCS： 发布：2005-06-01 实施：
简介： 信息：
JB/T 7405-2017 热重分析仪
简介：
信息：ICS：71.040.10 CCS：N53 发布：2017-04-12 实施：2018-01-01
ASTM E2402-2005 热重分析仪的质量损耗和剩余量测量验证的标准试验方法
简介：This method may be used to validate the performance of a specific TGA apparatus. This method may be used to validate the performance of a specific method based upon a TGA mass loss or residue measurement. This method may be used to determine the repeatability of a specific apparatus, operator or laboratory. This method may be used for specification and regulatory compliance purposes.1.1 This method provides procedures for validating mass loss and residue measurements by thermogravimetric analyzers (TGA) and analytical methods based upon the measurement of mass loss or residue content. Performance parameters determined include mass loss and residue repeatability (precision), detection limit, quantitation limit, linearity and bias.1.2 Validation of apparatus performance and analytical methods is requested or required for quality initiatives or where results may be used for legal purposes.1.3 SI units are the standard.1.4 There is no ISO standard equivalent to this method.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：71.040.10 (Chemical laboratories. Laboratory equip CCS：N61 发布：2005-01-01 实施：
简介： 信息：
JJG 1135-2017 热重分析仪
简介：
信息：ICS： CCS： 发布：2017-02-28 实施：2017-05-28
ASTM D6375-2005 用热重分析仪(TGA)Noack法测定润滑油蒸发损失的标准试验方法
简介：This test method is a safe and fast alternative for determination of the Noack evaporation loss of a lubricant. The evaporation loss of a lubricant is important in the hot zones of equipment where evaporation of part of the lubricant may increase lubricant consumption. Some lubricant specifications cite a maximum allowable evaporative loss.1.1 This test method covers the procedure for determining the Noack evaporation loss of lubricating oils using a thermogravimetric analyzer test (TGA). The test method is applicable to base stocks and fully formulated lubricant oils having a Noack evaporative loss ranging from 0 to 30 mass %. This procedure requires much smaller specimens, and is faster when multiple samples are sequentially analyzed, and safer than the standard Noack method using Wood's metal.1.2 The evaporative loss determined by this test method is the same as that determined using the standard Noack test methods.1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：75.100 (Lubricants, industrial oils and related pr CCS：E34 发布：2005 实施：
简介： 信息：
KS M ISO 248-2-2014(2019) 橡胶 原料 - 挥发物含量的测定 - 第2部分:使用带有红外干燥装置的自动分析仪的热重分析方法
简介：
信息：ICS：83.040.10 CCS： 发布：2014-09-02 实施：
ASTM E1582-04 热重分析仪的温度校准标准实践
简介：
信息：ICS：17.200.20 CCS： 发布：2004-05-01 实施：
简介： 信息：
ASTM E1582-14 热重分析仪的温度校准标准实践
简介：
信息：ICS：17.200.20 CCS： 发布：2014-05-01 实施：
ASTM E2040-03 热重分析仪质谱校准的标准测试方法
简介：
信息：ICS：71.040.50 CCS： 发布：2003-09-10 实施：
简介： 信息：
ASTM D6375-09(2014) 热重分析仪对润滑油蒸发损失的标准试验方法
简介：
信息：ICS：75.100 CCS： 发布：2014-05-01 实施：
ASTM E2040-2003 热重分析仪质量刻度校准的标准试验方法
简介：This test method calibrates or demonstrates conformity of thermogravimetric apparatus at ambient conditions. Most thermogravimetry analysis experiments are carried out under temperature ramp conditions or at isothermal temperatures distant from ambient conditions. This test method does not address the temperature effects on mass calibration. In most thermogravimetry experiments, the mass change is reported as weight percent in which the observed mass at any time during the course of the experiment is divided by the original mass of the test specimen. This method of reporting results assumes that the mass scale of the apparatus is linear with increasing mass. In such cases, it may be necessary only to confirm the performance of the instrument by comparison to a suitable reference. When the actual mass of the test specimen is recorded, the use of a calibration factor to correct the calibration of the apparatus may be required, on rare occasions.1.1 This test method covers the calibration or performance confirmation of the mass (or weight) scale of thermogravimetric analyzers and is applicable to commercial and custom-built apparatus. 1.2 Electronic instrumentation or automated data analysis and reduction systems or treatments equivalent to this test method may be used. 1.3 The values stated in SI units are to be regarded as the standard.
信息：ICS：71.040.50 (Physicochemical methods of analysis) CCS：N11 发布：2003 实施：
简介： 信息：
ASTM E2040-08(2014) 热重分析仪质谱校准的标准测试方法
简介：
信息：ICS：19.020 CCS： 发布：2014-03-15 实施：
ASTM E1582-00 热重分析仪的温度校准标准实践
简介：
信息：ICS：17.200.20 CCS： 发布：2000-05-10 实施：
简介： 信息：
ASTM E2551-13 用于热重分析仪的湿度发生器的湿度校准（或构造）的标准测试方法
简介：
信息：ICS：71.040.40 CCS： 发布：2013-04-01 实施：
ASTM E1582-93 热重分析仪的温度校准标准实践
简介：
信息：ICS：17.200.20 CCS： 发布：2000-05-10 实施：
简介： 信息：
ASTM E2551-2013 和热重分析仪一起使用的湿度发生器湿度校正 (或构型) 的标准试验方法
简介：5.1x00a0;This test method calibrates or demonstrates conformity of the humidity level in a purge gas generated by a humidity generator at a fixed temperature. Such calibration or demonstration of conformity may be required by quality initiatives. 5.2x00a0;Conformance demonstrates that the humidified purge gas is within some established limits. 5.3x00a0;Calibration provides an offset and or slope value that may be used for establishing the relative humidity scale of the apparatus. 1.1x00a0;This test method describes the humidity calibration (or conformance) of humidity generators for use with thermogravimetric analyzers and other thermal analysis apparatus. The humidity range covered is 5 to 958201;% relative humidity (% RH) and the temperature range is 0 to 80x00b0;C. 1.2x00a0;The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3x00a0;There are no ISO equivalents to this standard. 1.4x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：71.040.40 (Chemical analysis) CCS： 发布：2013 实施：
ASTM E2040-99 热重分析仪质谱校准的标准测试方法
简介：
信息：ICS：71.040.50 CCS： 发布：1999-09-10 实施：
简介： 信息：
ISO 248-2:2012 生胶和中灰；挥发物含量的测定第2部分:使用带红外干燥装置的自动分析仪的热重分析法
简介：
信息：ICS：83.040.10 CCS： 发布：2012-04-20 实施：
ASTM D6375-99a 用热重分析仪（TGA）Noack法测定润滑油蒸发损失的标准试验方法
简介：
信息：ICS：75.100 CCS： 发布：1999-06-10 实施：
简介： 信息：
ASTM E2402-2011 热重分析仪的质量损耗和剩余量测量验证的标准试验方法
简介：This method may be used to validate the performance of a specific TGA apparatus. This method may be used to validate the performance of a specific method based upon a TGA mass loss or residue measurement. This method may be used to determine the repeatability of a specific apparatus, operator or laboratory. This method may be used for specification and regulatory compliance purposes.1.1 This method provides procedures for validating mass loss and residue measurements by thermogravimetric analyzers (TGA) and analytical methods based upon the measurement of mass loss or residue content. Performance parameters determined include mass loss and residue repeatability (precision), detection limit, quantitation limit, linearity and bias. 1.2 Validation of apparatus performance and analytical methods is requested or required for quality initiatives or where results may be used for legal purposes. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 There is no ISO standard equivalent to this method. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：71.040.10 CCS：N61 发布：2011 实施：
ASTM E2040-1999 热重分析仪质量刻度校准的标准试验方法
简介：1.1 This test method covers the calibration or performance confirmation of the mass (or weight) scale of thermogravimetric analyzers and is applicable to commercial and custom-built apparatus. 1.2 Electronic instrumentation or automated data analysis and reduction systems or treatments equivalent to this test method may be used. 1.3 The values stated in SI units are to be regarded as the standard.
信息：ICS：71.040.50 (Physicochemical methods of analysis) CCS：N11 发布：1999 实施：
简介： 信息：
