橡胶化学检测标准橡胶化学-中析研究所检测

(CMA)

(CNAS)

(ISO)

(高新技术企业)

橡胶化学相关标准参考信息

GB/T 17783-2019 硫化橡胶或热塑性橡胶化学试验样品和试样的制备
简介：
信息：ICS：83.060 CCS：G40 发布：2019-12-10 00:00:00.0 实施：2020-11-01 00:00:00.0

KS M 6560-2009 化学用橡胶软管
简介：이 표준은 질산을 제외한 산 및 알칼리 용액(표 1) 등 일반적으로 송액용에 쓰이는 약품용
信息：ICS：23.040.70 CCS：G35 发布：2009-06-05 实施：2009-06-05

ASTM D6576-00 化学吹制柔性蜂窝橡胶的标准规格
简介：
信息：ICS：83.100 CCS：发布：2000-07-10 实施：

GB/T 9875-2001 橡胶聚合物的鉴定化学方法
简介：本标准规定了橡胶或橡胶制品中橡胶聚合物的化学定性鉴定方法。本标准适用于鉴别单独存在的或存在于橡胶制品中的天然橡胶(NR)和异戊橡胶(IR)、丁苯橡胶(SBR)、氯丁橡胶(CR)、丁腈橡胶(NBR)、丁基橡胶(IIR)等橡胶聚合物。对于并用橡胶建议不采用本标准，除非已用已知并用橡胶对本标准的可靠性进行确认后才可采用。
信息：ICS：83.060 CCS：G40 发布：2001-08-28 实施：2002-05-01

ASTM D6576-07 化学吹制柔性蜂窝橡胶的标准规格
简介：
信息：ICS：83.100 CCS：发布：2007-09-01 实施：

ASTM D5297-95(2000) 用高效液相色谱法测定橡胶化学促进剂纯度的标准试验方法
简介：
信息：ICS：71.080.30 CCS：发布：2000-01-01 实施：

GB/T 17531-1998 橡胶与橡胶制品化学试验方法准确度和偏差的确定
简介：本标准规定了评价橡胶与橡胶制品化学试验方法结果的准确度和偏差的准则。这些准则是对GB 4471和GB/T 14888的补充，并给出了准确度和偏差的表示形式。本标准适用于对试验方法准确度的评价，并局限于下列试验方法标准： --具有以定量的连续变量表示的哪些试验结果； --具有在测试项中可定量表示的那些试验结果。通过实验室内试验测定来表示的准确度和偏差，可作下列评价： a）试验方法服从实验室内试验的充分程度，这个充分程度指的是方法的准确度和数值很小的固定的偏差B、相对偏差B。 b）操作者偏差； c）样品偏差。
信息：ICS：83.140 CCS：G40 发布：1998-11-04 实施：1999-06-01

ASTM D6576-2007 化学吹制柔性多孔橡胶的标准规范
简介：1.1 This specification establishes requirements for chemically blown cellular rubber.1.2 In the case of conflict between the provisions of this specification and those of detailed specifications or test methods for a particular product, the latter shall take precedence.1.3 Unless specifically stated otherwise, by agreement between the purchaser and the supplier, all test methods shall be performed in accordance with the test methods specified in this specification.1.4 The values stated in SI units are to be regarded as the standard. The inch-pound units given in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.1.5 There is no known ISO equivalent to this specification.Note 1This specification was revised using the updated test methods and specifications in Specification D 1056 - 07.
信息：ICS：83.100 (Cellular materials) CCS：G34 发布：2007 实施：

ASTM D6576-2000 化学吹制挠性多孔橡胶标准规范
简介：1.1 This specification establishes requirements for chemically blown cellular rubber.1.2 In the case of conflict between the provisions of this specification and those of detailed specifications or test methods for a particular product, the latter shall take precedence.1.3 Unless specifically stated otherwise, by agreement between the purchaser and the supplier, all test methods shall be performed in accordance with the test methods specified in this specification.1.4 The values stated in SI units are to be regarded as the standard. The inch-pound units given in parentheses are for information only.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.1.6 This specification and ISO 6916 are not equivalent.Note 1--This specification was revised using the updated test methods and specification in Specification D1056 - 98.
信息：ICS：83.100 (Cellular materials) CCS：G40 发布：2000 实施：

GB/T 6039-1997 橡胶物理试验和化学试验术语
简介：本标准规定了橡胶工业中橡胶通用物理试验和化学试验所用的术语及其定义。本标准适用于制定、修订标准，编写书刊及有关技术文件。
信息：ICS：83.060 CCS：G40 发布：1997-09-26 实施：1998-04-01

ASTM D4578-2006 橡胶化学制品的标准试验方法.萃取法测定硫磺百分比
简介：Test Method A is commonly used for quality control testing because of the solvent efficiency of carbon disulfide. Test Method B employs toluene as a solvent because it is less toxic and less volatile than carbon disulfide. Test Method B is more likely to be used for research and development or for any other purpose where such information may be useful.1.1 These test methods cover the determination of solvent insoluble materials in a sulfur sample. The two test methods available are: (1) Test Method A, Extraction by Carbon Disulfide, and (2) Test Method B, Extraction by Toluene. If there are no other solvent insoluble materials present in the sulfur, these test methods determine the insoluble sulfur content directly. If other materials are also present, additional testing is necessary to identify what portion of the insolubles is insoluble sulfur.1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For a specific warning, see 5.1.
信息：ICS：83.040.20 (Rubber compounding ingredients) CCS：G40 发布：2006 实施：

BS 7825-3.11-1998 橡胶和塑料试验设备的校准.校准一览表.橡胶聚合物的识别和化学性能
简介：This section of BS 7825 provides schedules for the calibration of equipment and apparatus used for the identification of rubber polymers and the determination of their chemical properties and constituents.
信息：ICS：83.020 CCS：G95 发布：1998-11-15 实施：1998-11-15

ASTM D6576-20 化学吹制柔性蜂窝橡胶的标准规格
简介：
信息：ICS：83.100 CCS：发布：2020-07-01 实施：

ASTM D1766-2005 橡胶化学制品的标准试验方法.溶解性
简介：This test method may be used as a raw material quality-control tool.1.1 This test method covers a practical test for the solubility of commercial chemicals used in rubber products. 1.2 It is not a true measure of solubility, since equilibrium is not approached from both sides, that is, higher temperature and lower temperature. 1.3 The test method indicates the total solubility, under the conditions of the test, of all components in the presence of each other and in the proportions present in the sample. 1.4 This test method does not measure the solubility of a rubber chemical in rubber. 1.5 The values stated in SI units are to be considered standard. 1.6 This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：83.040.20 (Rubber compounding ingredients) CCS：G34 发布：2005 实施：

SAE AMS-R-6130-1998 化学吹气的蜂窝橡胶;替代1998年12月18日作废的MIL-R-6130
简介：This specification establishes requirements for chemically blown cellular rubber.
信息：ICS： CCS：V13 发布：1998-07 实施：

ASTM D5666-95(2019) 橡胶化学防降解剂的标准试验方法&x2014；高效液相色谱法测定苯二胺（PPD）抗降解剂的纯度
简介：
信息：ICS：71.100.45 CCS：发布：2019-01-01 实施：

ASTM D1817-2005 橡胶化学制品的标准试验方法.密度
简介：The density of a rubber chemical is used for calculating the rubber compound volume, which is used to determine the cost of a rubber product. The density may also be used as a raw material control tool.1.1 This test method covers the determination of the density of solid chemicals used as rubber additives during processing and manufacture. It is intended for determining the density of the rubber chemical itself and not for the determination of the effective density of the chemical in a rubber. 1.2 The values stated in SI units shall be regarded as standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：83.040.20 (Rubber compounding ingredients) CCS：G40 发布：2005 实施：

JIS K6227-1998 橡胶.碳黑含量的测定.热解和化学降解法
简介：この規格は，ゴム中のカーボンブラック含有量の測定に用いる熱分解法(A法)及び二つの化学分解法(B法及びC法)について規定する。
信息：ICS：83.060 CCS：G49 发布：1998-03-20 实施：

ASTM D5297-95(2019) 橡胶化学促进剂的标准试验方法&x2014；高效液相色谱法测定纯度
简介：
信息：ICS：71.080.30 CCS：发布：2019-01-01 实施：

ASTM D1817-2005(2011) 橡胶化学光密度标准试验方法
简介：The density of a rubber chemical is used for calculating the rubber compound volume, which is used to determine the cost of a rubber product. The density may also be used as a raw material control tool.1.1 This test method covers the determination of the density of solid chemicals used as rubber additives during processing and manufacture. It is intended for determining the density of the rubber chemical itself and not for the determination of the effective density of the chemical in a rubber. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：83.040.20 (Rubber compounding ingredients) CCS：G40 发布：2005 实施：

ASTM D1991-1996(2001) 橡胶化学标准试验方法.二巯基苯并噻唑(MBT).化验
简介：1.1 This test method covers a procedure for the assay of 2-mercaptobenzothiazole (MBT). It is based on a potentiometric titration of MBT with sodium hydroxide. 1.2 The assay is determined as percent by mass. 1.3 The values given in SI units are to be regarded as standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：83.040.20 (Rubber compounding ingredients) CCS：G34 发布：1996 实施：

ISO/TS 22640-2018 橡胶.轮胎和道路磨损颗粒物理和化学特性的框架（TRWP）
简介：
信息：ICS：83.060 CCS：发布：2018-07-13 实施：

ASTM D1991-2005(2010) 橡胶化学试验方法 8212;2- 二巯基苯并噻唑(MBT)8212;化验用标准试验方法
简介：MBT is commonly used as an accelerator for rubber and latex vulcanization. The purity of MBT may be of importance in predicting performance in rubber compounds and this test method is designed to assess the purity of MBT. This test method may be used as a quality control tool and for research and development work.1.1 This test method covers a procedure for the assay of 2-mercaptobenzothiazole (MBT). It is based on a potentiometric titration of MBT with sodium hydroxide. 1.2 The assay is determined as percent by mass. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：83.040.20 CCS：G34 发布：2005 实施：

ASTM D1766-1996 橡胶化学制品的标准试验方法.溶解性
简介：1.1 This test method covers a practical test for the solubility of commercial chemicals used in rubber products. 1.2 It is not a true measure of solubility, since equilibrium is not approached from both sides, that is, higher temperature and lower temperature. 1.3 The test method indicates the total solubility, under the conditions of the test, of all components in the presence of each other and in the proportions present in the sample. 1.4 This test method does not measure the solubility of a rubber chemical in rubber. 1.5 The values stated in SI units are to be considered standard. 1.6 This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：83.040.20 (Rubber compounding ingredients) CCS：G40 发布：1996 实施：

ASTM D5900-2015 工业基准材料 (IRM) 的物理和化学性能的标准规范. 本规范在ASTM委员会D11橡胶规定的司法管辖范围内, 属于直接责任
简介：3.1x00a0;IRMs are vitally important in product and specification testing, in research and development work, in technical service work, and in quality control operatio 1.1x00a0;This specification covers the chemical and physical quality specifications or requirements, or both, for Industry Reference Materials (IRMs) as cited in Practice D4678 and other standards. 1.2x00a0;IRMs, as evaluated and referenced in Practice D4678, are vitally important to conduct product, specification, and development testing in the rubber and carbon black industries. 1.3x00a0;Before a new lot of material can be accepted as an IRM, it must comply with the specifications prescribed in this specification. However, these specifications are only part of the requirements. Other requirements as given in Practice D4678 shall be met before a candidate material can be formally accepted as an IRM. 1.4x00a0;The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：19.020;83.020 CCS：发布：2015 实施：

ASTM D1991-2005 橡胶化学制品的标准试验方法.二巯基苯并噻唑(MBT).化验
简介：MBT is commonly used as an accelerator for rubber and latex vulcanization. The purity of MBT may be of importance in predicting performance in rubber compounds and this test method is designed to assess the purity of MBT. This test method may be used as a quality control tool and for research and development work.1.1 This test method covers a procedure for the assay of 2-mercaptobenzothiazole (MBT). It is based on a potentiometric titration of MBT with sodium hydroxide. 1.2 The assay is determined as percent by mass. 1.3 The values given in SI units are to be regarded as standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：83.040.20 (Rubber compounding ingredients) CCS：G34 发布：2005 实施：

ASTM D1991-1996 橡胶化学标准试验方法.二巯基苯并噻唑(MBT).化验
简介：1.1 This test method covers a procedure for the assay of 2-mercaptobenzothiazole (MBT). It is based on a potentiometric titration of MBT with sodium hydroxide. 1.2 The assay is determined as percent by mass. 1.3 The values given in SI units are to be regarded as standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS： CCS：G34 发布：1996 实施：

ASTM D5666-95(2014) 橡胶化学防降解剂的标准试验方法&mdash；高效液相色谱法测定苯二胺（PPD）抗降解剂的纯度
简介：
信息：ICS：71.100.45 CCS：发布：2014-08-01 实施：

ASTM D5297-95(2004) 用高效液相色谱法测定橡胶化学促进剂纯度的标准试验方法
简介：
信息：ICS：71.080.30 CCS：发布：2004-12-01 实施：

ISO 1408:1995 橡胶——炭黑含量的测定——热解和化学降解方法
简介：
信息：ICS：83.060 CCS：发布：1995-10-05 实施：

ASTM D5297-95(2014) 橡胶化学加速剂标准试验方法
简介：
信息：ICS：71.080.30 CCS：发布：2014-08-01 实施：

ASTM D2702-2004 橡胶加工用化学药液的红外线吸收特性测定的标准实施规程
简介：1.1 This analytical technique provides a simple, rapid practice to prove the identity of a rubber chemical before incorporation into a rubber mix by comparison of its infrared absorption spectrum with that of a reference specimen. 1.2 This technique can also be used to detect gross contamination or large differences in rubber chemicals. Thus, it can provide a basis for producer-consumer agreement. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：83.040.10 (Latex and raw rubber) CCS：G34 发布：2004 实施：

ISO 1408-1995 橡胶炭黑含量的测定热解和化学降解法
简介：Describes a pyrolytic method (A) and two chemical degradation methods (B and C) for the determination of the carbon black content of artificial rubber and copolymers. Replaces the second edition, of which it constitutes a minor revision.
信息：ICS：83.060 CCS：G34 发布：1995-10 实施：

ASTM D6576-13 化学吹制柔性蜂窝橡胶的标准规格
简介：
信息：ICS：83.100 CCS：发布：2013-11-15 实施：

ASTM D3853-2003e1 与橡胶及橡胶胶乳相关的标准术语.合成化学制品的缩写
简介：1.1 This terminology is a compilation of abbreviations for accelerators, vulcanizing agents, activators, antidegradants, plasticizers, softeners, processing aids, blowing agents, retarders, isocyanates, peroxides, and antireversion agents used in the compounding of rubber products. Abbreviations for rubbers are listed in Practice D 1418 and a numbering system for various grades of carbon blacks is described in Classification D 1765.
信息：ICS：83.040.10 (Latex and raw rubber); 83.060 (Rubber) CCS：G35 发布：2003 实施：

JIS K6342-1995 化学用的橡胶软管
简介：
信息：ICS：83.140.40 CCS：G42 发布：1995-05-01 实施：

KS M ISO 1408-2012 橡胶.炭黑含量的测定.热解和化学降解法
简介：이 표준은 고무의 카본 블랙 함량 측정을 위한 열분해법(A)과 두 가지 화학적 분해법(B와
信息：ICS：83.060 CCS：G34 发布：2012-03-19 实施：2012-03-19

ASTM D4573-2003 橡胶化学制品的标准试验方法.被油浸过的硫磺中含油量的测定
简介：This test method measures the hydrocarbon oils added to sulfur to help control dusting of the sulfur. It can be used for research, development, and quality control to measure the level of oil added to the sulfur to help maintain the oil content at required levels.1.1 This test method covers the determination of the amount of hydrocarbon oils added to oil-treated sulfurs. The test method is employed when the amount of oil added is 1 % or more of the total sample.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：83.040.20 (Rubber compounding ingredients) CCS：G34 发布：2003 实施：

ASTM D1519-1995(2004)e1 橡胶化学制品熔化范围的标准试验方法
简介：This test method may be used for research and development. It also may be used for quality assurance, provided a standard has been agreed upon between a producer and a user. For identification purposes, melting range should be supplemented by measurements of a more specific physical and chemical property. This test method is not recommended for rubber chemicals that decompose at their melting ranges. The melting range as determined by Test Method Ax2014;Capillary Tube Melting Range is not recommended as a criterion of purity of a rubber chemical.1.1 This test method covers the determination of the melting range of commercial rubber processing chemicals either by use of capillary melting point tubes or by differential scanning calorimetry (DSC). 1.2 The values stated in SI units are to be regarded as the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：83.040.20 (Rubber compounding ingredients) CCS：G40 发布：1995 实施：

KS M ISO 1408-2012(2017) 橡胶炭黑含量的测定热解法和化学降解法
简介：
信息：ICS：83.060 CCS：发布：2012-03-19 实施：

ASTM D5051-2002 橡胶化学制品苯并噻唑基二硫化物(MBTS)的标准试验方法.分析
简介：1.1 This test method describes the determination of assay of benzothiazyl disulfide (MBTS). It is based on a titration of free iodine liberated upon reduction of MBTS, with potassium iodide (KI) in acid medium. 1.2 The assay is determined as mass percent. 1.3 Free 2-mercaptobenzothiazole (MBT) content is not determined. 1.4 The values stated in SI units are to be regarded as the standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：83.060 (Rubber) CCS：G34 发布：2002 实施：

ASTM D1519-1995(2009) 橡胶化学制品的标准试验方法.溶化范围
简介：This test method may be used for research and development. It also may be used for quality assurance, provided a standard has been agreed upon between a producer and a user. For identification purposes, melting range should be supplemented by measurements of a more specific physical and chemical property. This test method is not recommended for rubber chemicals that decompose at their melting ranges. The melting range as determined by Test Method Ax2014;Capillary Tube Melting Range is not recommended as a criterion of purity of a rubber chemical.1.1 These test methods cover the determination of the melting range of commercial rubber processing chemicals either by use of capillary melting point tubes or by differential scanning calorimetry (DSC). 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：83.040.20 (Rubber compounding ingredients) CCS：发布：1995 实施：

KS M ISO 1408-2012(2022) 橡胶炭黑含量的测定热解法和化学降解法
简介：
信息：ICS：83.060 CCS：发布：2012-03-19 实施：

ASTM D5044-2002 橡胶化学制品苯并噻唑基二硫化物(MBTS)中游离2-硫醇苯并噻唑(MBT)的标准试验方法
简介：1.1 This test method describes the procedure for estimation of the chloroform-soluble, acidic impurities in benzothiazyl disulfide (MBTS). 1.2 The values stated in SI units are to be regarded as the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：83.060 (Rubber) CCS：G34 发布：2002 实施：

ASTM D5297-1995(2014) 使用高效液相色谱法测定橡胶化学促进剂纯度的标准试验方法
简介：5.1x00a0;These test methods are designed to determine the purity of rubber chemical accelerators. 5.2x00a0;Since the results of these test methods are based on an integrated peak area, it is assumed that all analytes of interest are resolved from interfering peaks. 1.1x00a0;These test methods cover the determination of the purity of present commercially available rubber chemical accelerators in the range from 80 to 1008201;% by high performance liquid chromatography (HPLC) using ultraviolet detection and external standard calculations. 1.2x00a0;Expertise in HPLC is necessary to the successful application of these test methods. 1.3x00a0;The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：71.080.30 CCS：发布：1995 实施：

ASTM D4570-2002 橡胶化学制品的标准试验方法.用筛分法(干法)测定硫的粒度
简介：This test method is used to evaluate sulfur for suitability as a rubber vulcanizing agent. Sulfur particles must be small enough to dissolve in rubber during cure to produce a uniform network of cross-links. This test method is used as a quality control method to ensure that large particles are not present (and to determine if the sulfur follows a typical pattern for size distribution).1.1 This test method covers the particle size measurement of the coarse fraction of ground sulfurs. It is limited to measurement of particles greater than 45 956;m (No. 325 sieve). If the sulfur is very fine and the screens become plugged by the caking of the sulfur, it may be necessary to use a wet sieve procedure instead.1.2 The values stated in SI units are to be regarded as the standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：83.060 (Rubber) CCS：G34 发布：2002 实施：

ASTM D1519-1995(2009)e1 橡胶化学制品的标准试验方法.熔点范围
简介：This test method may be used for research and development. It also may be used for quality assurance, provided a standard has been agreed upon between a producer and a user. For identification purposes, melting range should be supplemented by measurements of a more specific physical and chemical property. This test method is not recommended for rubber chemicals that decompose at their melting ranges. The melting range as determined by Test Method ACapillary Tube Melting Range is not recommended as a criterion of purity of a rubber chemical.1.1 These test methods cover the determination of the melting range of commercial rubber processing chemicals either by use of capillary melting point tubes or by differential scanning calorimetry (DSC). 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：83.040.20 CCS：G40 发布：1995 实施：

NF T47-284-2011 液态或气态化学制品用橡胶和热塑性软管及其配件.规格
简介：
信息：ICS：23.040.70 CCS：G42;G33 发布：2011-04-01 实施：2011-04-02

AS 1683.17-2001 橡胶的试验方法.测定硫化橡胶的炭黑含量.热解和化学降解法
简介：Specifies a pyrolytic and two chemical degradation methods for the determination of the carbon content of rubber. This Standard is identical with and has been reproduced from ISO 1408:1995.
信息：ICS：83.060 CCS：发布：2001-06-29 实施：

ASTM D5666-1995(2014) 橡胶化学抗降解剂的标准试验方法. 使用高效液相色谱法测定对苯二胺 (PPD) 抗降解剂的纯度
简介：5.1x00a0;This test method is designed to determine the purity of p-phenylenediamine antidegradants. 5.2x00a0;Since the results of this test method are based on an integrated peak area as determined by HPLC, it is assumed that all analytes of interest are resolved from interfering peaks. 1.1x00a0;This test method covers the purity of Type I, II, and III p-phenylenediamine (PPD) antidegradants as described in Classification D4676 by high performance liquid chromatography (HPLC) using ultraviolet detection and external standard calculations. 1.2x00a0;Expertise in HPLC is necessary to the successful application of this test method. 1.3x00a0;The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：71.100.45 CCS：发布：1995 实施：

EN 12115-2011 橡胶和热塑性塑料软管和软管组件对液体或气体的化学物质.规范
简介：This European Standard specifies requirements for two types of hose assemblies (Types D and SD) and four grades based on electrical properties with hoses made of rubber or thermoplastics and hose fittings made of metal designed to convey liquid or gaseous chemical substances, hereinafter termed the "chemicals conveyed". The hose assemblies are intended for use with chemicals conveyed in the temperature range of-20 ℃ to +65 ℃ at a working pressure
信息：ICS：23.040.70 CCS：发布：2011-01-01 实施：

NF T45-018-2001 橡胶工业用原材料.化学制品.色散和主要混合物
简介：
信息：ICS：83.040.20 CCS：G34 发布：2001-03-01 实施：2001-03-20

BS 7164-11.1-1994 生橡胶和硫化橡胶的化学试验.丁二烯橡胶.显微结构测定方法
简介：This Section of BS 7164 specifies a method for the determination of the microstructure of butadiene rubber.
信息：ICS：83.060 CCS：G34 发布：1994-05-15 实施：1994-05-15

ASTM D5297-95(2009) 用高效液相色谱法测定橡胶化学促进剂纯度的标准试验方法
简介：
信息：ICS：71.080.30 CCS：发布：2009-07-01 实施：

FORD FLTM EU-AP 050-02-2001 经硫化处理的橡胶混合物的化学-物理分析
简介：
信息：ICS： CCS：发布：2001-01-31 实施：

ISO/TR 9474:1993 橡胶和橡胶制品.化学试验方法准确度和偏差的测定
简介：
信息：ICS：83.060 CCS：发布：1993-08-19 实施：

ASTM D1766-2001 橡胶化学制品的标准试验方法.溶解性
简介：1.1 This test method covers a practical test for the solubility of commercial chemicals used in rubber products. 1.2 It is not a true measure of solubility, since equilibrium is not approached from both sides, that is, higher temperature and lower temperature. 1.3 The test method indicates the total solubility, under the conditions of the test, of all components in the presence of each other and in the proportions present in the sample. 1.4 This test method does not measure the solubility of a rubber chemical in rubber. 1.5 The values stated in SI units are to be considered standard. 1.6 This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：83.040.20 (Rubber compounding ingredients) CCS：G40 发布：2001 实施：

ISO/TR 9474-1993 橡胶和橡胶制品.化学试验方法的准确度和偏差的测定
简介：
信息：ICS：83.060 CCS：G40 发布：1993-08 实施：