拉伸负荷检测标准拉伸负荷-中析研究所检测

(CMA)

(CNAS)

(ISO)

(高新技术企业)

拉伸负荷相关标准参考信息

GB/T 41794-2022 土工合成材料聚烯烃土工膜耐应力开裂性能的评价切口恒定拉伸负荷法
简介：
信息：ICS：83.140.10 CCS：G33 发布：2022-10-14 实施：2023-05-01

KS M ISO 283-2009(2021) 纺织输送带全厚度拉伸强度、断裂伸长率和基准负荷伸长率试验方法
简介：
信息：ICS：53.040.20 CCS：发布：2009-03-20 实施：

ASTM F1804-2003 拉入安装过程中聚乙烯气体管允许拉伸负荷测定的标准实施规范
简介：1.1 This practice provides a means to determine an allowable tensile load (ATL) value for a polyethylene gas pipe that is to be installed underground using methods that pull the pipe into a trench (cut or plowed), bore hole, casing pipe, or the like. The ATL value takes into account pipe size, tensile yeild strength, pipe temperature, and pulling load duration.1.2 The ATL is used to set the break-away strength for a "weak-link" device, or as a limit setting for other devices that control the maximum pulling force exerted by equipment used to pull polyethylene gas pipe into an underground location, or to determine if pulling equipment can extert pulling force greater than the ATL value for the gas pipe being installed. A weak-link device is installed where the pipe pulling equipment is connected to the polyethylene gas pipe. If pulling load exceeds the ATL limit, the device de-couples the pipe from the pulling equipment. Other measures or equipment that limit the pulling force on the pipe are also used. When the ATL value is compared to the pulling force developed by the pull-in installation equipment and equipment cannot extert pulling force greater than the ATL value, a weak-link or other device for limiting the pulling force is not necessary.1.3 This practice does not address weak-link device design or requirements, nor does it address the design or requirements for other equipment or procedures used to limit the pulling force applied to polyethylene gas pipe during pull-in installation.1.4 This practice does not address installation methods or procedures employed for pull-in of polyethylene gas pipe.1.5 Throughout this practice, inch-pound units shall be regarded as standard with SI units in parentheses for informational purposes.1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：23.040.20 (Plastic pipes) CCS：发布：2003 实施：

GB/T 38612-2020 人造革合成革试验方法拉伸负荷及断裂伸长率的测定
简介：
信息：ICS：59.080.40 CCS：Y47 发布：2020-03-31 00:00:00.0 实施：2020-10-01 00:00:00.0

ASTM D7580/D7580M-2009(2014) 用于测定同质托盘化或者成套负荷无源射频识别转发器可读性的旋转拉伸包装方法的标准试验方法
简介：5.1x00a0;This test method is intended to be used as a means to verify the readability of RFID tagged unitized loads. 5.2x00a0;This test method simulates an RF read point at stage of unitizing a load using a stretch wrapper. Reading RF tags on a stretch wrapper is beneficial because the dynamic rotary motion of the unitized load within the stationary RF field increases the likelihood of successful reads. 5.3x00a0;This test method is intended for systems used exclusively within the United States. Additional test standards from ISO or other standards bodies may apply to internationally handled goods, and may include additional test scenarios not outlined in this document. 1.1x00a0;This test method quantitatively evaluates the readability of radio frequency identification (RFID) tagged unitized load in a simulated stretch wrapper read point scenario. 1.2x00a0;This test method is intended for use in laboratory settings that simulate, as closely as is practicable, the distribution environment of the product being tested or within the actual distribution environment itself. 1.3x00a0;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：35.240.60 CCS：发布：2009 实施：

ASTM D3164-2003 用拉伸负荷法测定胶粘剂粘接塑料搭接接头剪切强度特性的标准试验方法
简介：Due to the increased use of adhesively bonded plastics as a result of the inherent advantages afforded by bonded rather than mechanically fastened joints, particularly the alleviation of stress risers and stress cracking, there is a need for standard tests by which joints of various substrates and adhesives can be compared. This test method is intended to meet such a need. This test method is limited to test temperatures below the softening point of the subject adherends, and is not intended for use on anisotropic adherends such as reinforced plastic laminates. The misuse of strength values obtained from this test method as design stress allowable values for structural joints could lead to product failure, property damage, and human injury. The apparent shear strength of an adhesive obtained from a given small single-lap specimen may differ from that obtained from a joint made with different adherends or by a different bonding process. The normal variation of temperature and moisture in the service environment causes the adherends and the adhesive to swell and shrink. The adherends and adhesive are likely to have different thermal and moisture coefficients of expansion. Even in small specimens, short-term environmental changes can induce internal stresses or chemical changes in the adhesive that permanently affect the apparent strength and other mechanical properties of the adhesive. The problem of predicting joint behavior in a changing environment is even more difficult if a different type of adherend is used in a larger structural joint than was used in the small specimen. The apparent shear strength measured with a single-lap specimen is not suitable for determining allowable design stresses for designing structural joints that differ in any manner from the joints tested without thorough analysis and understanding of the joint and adhesive behaviors. Single-lap tests may be used for comparing and selecting adhesives or bonding processes for susceptibility to fatigue and environmental changes, but such comparisons must be made with great caution since different adhesives may respond differently in different joints. See Guide D 4896 for further discussion of the concepts relative to interpretation of adhesive bonded single lap joints.1.1 This test method is intended to complement Test Method D 1002 and Test Method D 3163 and extend its application to single-lap-shear adhesive joints employing plastic adherends. The test method is useful for generating comparative shear strength data for joints made from a number of plastics. It can also provide a means by which several plastics surface treatments can be compared.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.Note 18212;A complete metric companion to Test Method D 3164 has been developed - D 3164M.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：83.180 (Adhesives) CCS：G38 发布：2003 实施：

GB/T 23427-2009 造船与海上结构物.受拉伸负荷的眼板和叉头组件.主要尺寸
简介：本标准规定了船用受拉伸负荷的眼板和叉头组件及其连接螺栓或销的主要互换尺寸与材料。本标准仅适用于受拉伸负荷的船上货物装卸设备的构件（例如圆孔眼板、滑车头装置、滑车支架、索座架、松紧螺旋扣）。本标准不适用于承受侧向压缩力或扭转载荷的构件（例如与吊杆鹅颈销连接的叉型吊杆座配件）。
信息：ICS：47.020.10 CCS：U24 发布：2009-03-23 实施：2009-11-01

DIN EN ISO 283-2008 织物传送带.全厚度拉伸强度、断裂伸长和基准负荷下伸长的试验方法
简介：This International Standard specifies a test method for the determination of the full thickness tensile strengthin the longitudinal direction and the elongation at the reference force and breaking point of conveyor beltshaving a textile carcass. The method can also be used for the determination of full thickness tensile strengthin the transverse direction and the elongation at the breaking point, for use when the manufacturer isrequested by the purchaser to state values for these properties.This International Standard is not suitable or valid for light conveyor belts as described in ISO 21183-1.
信息：ICS：53.040.20 CCS：J81 发布：2008-02 实施：

SNI 03-6761-2002 单独支柱静态轴向拉伸负荷检测方法
简介：
信息：ICS：91.080.01 CCS：发布：2002 实施：

GB/T 4157-1984 金属抗硫化物应力腐蚀开裂恒负荷拉伸试验方法
简介：本标准规定的试验方法是在实验室内，在含有硫化氢的酸性水溶液中，对承受拉伸应力的金属进行抗开裂破坏性能的试验。
信息：ICS：77.040.10 CCS：H22 发布：1984-02-24 实施：1985-01-01

ISO 2285:2007 硫化橡胶或热塑性橡胶.恒定伸长率下拉伸永久变形和恒定拉伸负荷下拉伸永久变形、伸长率和蠕变的测定
简介：
信息：ICS：83.060 CCS：发布：2007-07-10 实施：

ISO 2285:2001 硫化橡胶或热塑性橡胶.恒定伸长率下拉伸永久变形和恒定拉伸负荷下拉伸永久变形、伸长率和蠕变的测定
简介：
信息：ICS：83.060 CCS：发布：2001-12-20 实施：

ASTM D5397-20 用缺口恒拉伸负荷试验评定聚烯烃土工膜抗应力开裂性的标准试验方法
简介：
信息：ICS：59.080.70 CCS：发布：2020-06-01 实施：

ASTM D5397-07 用缺口恒拉伸负荷试验评定聚烯烃土工膜抗应力开裂性的标准试验方法
简介：
信息：ICS：59.080.70 CCS：发布：2007-06-01 实施：

FORD FLTM BN 013-07-2001 有芯或无芯挤压乙烯基贴边组件在拉伸负荷下的伸长率
简介：
信息：ICS： CCS：发布：2001-08-22 实施：

ASTM D5397-19a 用缺口恒拉伸负荷试验评定聚烯烃土工膜抗应力开裂性的标准试验方法
简介：
信息：ICS：59.080.70 CCS：发布：2019-10-15 实施：

ASTM D3165-2007 用单面搭接迭层板组件的拉伸负荷测定剪切时胶粘剂强度特性的标准试验方法
简介：This test method is useful in that the joint configuration closely simulates the actual joint configuration of many bonded assemblies. Surface preparation of the adherends can affect the apparent shear strength of the adhesive and can be one of the variables under study. This test method is also useful as an in-process quality control test for laminated assemblies. In practice the laminated assembly is either made over size and test specimens removed from it or a percentage of the assemblies are destructively tested. The misuse of strength values obtained from this test method as design allowable stress values for structural joints could lead to product failure, property damage, and human injury. The apparent shear strength of an adhesive obtained from a given small single-lap specimen may differ from that obtained from a joint made with different adherends or by a different bonding process. The normal variation of temperature and moisture in the service environment causes the adherends and the adhesive to swell and shrink. The adherends and adhesive are likely to have different thermal and moisture coefficients of expansion. 4.3.1 Even in small specimens, short-term environmental changes can induce internal stresses or chemical changes in the adhesive that permanently affect the apparent strength and other mechanical properties of the adhesive. The problem of predicting joint behavior in a changing environment is even more difficult if a different type of adherend is used in a larger structural joint than was used in the small specimen. The apparent shear strength measured with a single-lap specimen is not suitable for determining design allowable stresses for designing structural joints that differ in any manner from the joints tested without thorough analysis and understanding of the joint and adhesive behaviors. Single-lap tests may be used for comparing and selecting adhesives or bonding processes for susceptibility to fatigue and environmental changes, but such comparisons must be made with great caution since different adhesives may respond differently in different joints. Review Guide D 4896 for further discussion of concepts for interpretation of adhesive-bonded single-lap joint data.1.1 This test method (Note 1) is intended for determining the comparative shear strengths of adhesives in large area joints when tested on a standard single-lap-joint specimen and under specified conditions of preparation and testing. Adhesives respond differently in small versus large area joints (Note 2). Note 1While this test method is intended for use in metal-to-metal applications, it may be used for measuring the shear properties of adhesives using plastic adherends, provided consideration is given to the thickness and rigidityof the plastic adherends. Doublers or bonded tabs may be required for plastic adherends to prevent bearing failure in the adherends.Note 2This variation can be influenced by adhesive density, flow characteristics, cure rate, gel time, carrier composition, entrapped volatiles, volatiles released during cure, etc. and also by cure cycle variables including: temperature, time, pressure, rise rate to temperature, cool-down rate, etc. In addition to the processing variables joint size changes the level of constraint on the adhesive as well as the influence of induced tensile loads at the edge of the joint during mechanical or thermal loading.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of ......
信息：ICS：83.180 (Adhesives) CCS：G39 发布：2007 实施：

ISO 283-1-2000 织物输送带全厚度拉伸试验第1部分:在标准负荷下拉伸强度、拉断伸长及定伸的测定
简介：
信息：ICS：53.040.20 CCS：J81 发布：2000-10 实施：

ASTM D5397-19 用缺口恒拉伸负荷试验评定聚烯烃土工膜抗应力开裂性的标准试验方法
简介：
信息：ICS：59.080.70 CCS：发布：2019-01-01 实施：

ASTM D3165-2007(2014) 用单面搭接迭层板组件的拉伸负荷测定剪切时胶粘剂强度特性的标准试验方法
简介：4.1x00a0;This test method is useful in that the joint configuration closely simulates the actual joint configuration of many bonded assemblies. Surface preparation of the adherends can affect the apparent shear strength of the adhesive and can be one of the variables under study. 4.2x00a0;This test method is also useful as an in-process quality control test for laminated assemblies. In practice the laminated assembly is either made over size and test specimens removed from it or a percentage of the assemblies are destructively tested. 4.3x00a0;The misuse of strength values obtained from this test method as design allowable stress values for structural joints could lead to product failure, property damage, and human injury. The apparent shear strength of an adhesive obtained from a given small single-lap specimen may differ from that obtained from a joint made with different adherends or by a different bonding process. The normal variation of temperature and moisture in the service environment causes the adherends and the adhesive to swell and shrink. The adherends and adhesive are likely to have different thermal and moisture coefficients of expansion. 4.3.1x00a0;Even in small specimens, short-term environmental changes can induce internal stresses or chemical changes in the adhesive that permanently affect the apparent strength and other mechanical properties of the adhesive. The problem of predicting joint behavior in a changing environment is even more difficult if a different type of adherend is used in a larger structural joint than was used in the small specimen. 4.4x00a0;The apparent shear strength measured with a single-lap specimen is not suitable for determining design allowable stresses for designing structural joints that differ in any manner from the joints tested without thorough analysis and understanding of the joint and adhesive behaviors. 4.5x00a0;Single-lap tests may be used for comparing and selecting adhesives or bonding processes for susceptibility to fatigue and environmental changes, but such comparisons must be made with great caution since different adhesives may respond differently in different joints. Review Guide D4896 for further discussion of concepts for interpretation of adhesive-bonded single-lap joint data. 1.1x00a0;This test method (Note 1) is intended for determining the comparative shear strengths of adhesives in large area joints when tested on a standard single-lap-joint specimen and under specified conditions of preparation and testing. Adhesives respond differently in small versus large area joints (Note 2).Note 1x2014;While this test method is intended for use in metal-to-metal applications, it may be used for measuring the shear properties of adhesives using plastic adherends, provided consideration is given to the thickness and rigidity of the plastic adherends. Doublers or bonded tabs may be required for plastic adherends to prevent bearing failure in the adherends.Note 2x2014;This variation can be influenced by adhesive density, flow characteristics, cure rate, gel time, carrier composition, entrapped volatiles, volatiles released during cure, etc. and also by cure cycle variables including: temperature, time, pressure, rise rate to temperature, cool-down rate, etc. In addition to the processing variables joint size changes the level of constraint on the adhesive ......
信息：ICS：83.180 (Adhesives) CCS：发布：2007 实施：

ASTM D5397-99 用缺口恒拉伸负荷试验评定聚烯烃土工膜抗应力开裂性的标准试验方法
简介：
信息：ICS： CCS：发布：1999-12-10 实施：

ISO 6237-2017 粘合剂.木材与木材粘结体.用拉伸负荷测定剪切强度
简介：
信息：ICS：83.180 CCS：G38 发布：2017-1101 实施：

NF T51-170-2-2006 塑料制品.耐环境应力开裂(ESC)的测定.第2部分:恒定拉伸负荷法
简介：
信息：ICS：83.080.01 CCS：G31 发布：2006-11-01 实施：2006-11-20

ASTM D5397-99e1 用缺口恒拉伸负荷试验评定聚烯烃土工膜抗应力开裂性的标准试验方法
简介：
信息：ICS：59.080.70 CCS：发布：1999-12-10 实施：

EN 15416-1-2017 苯酚和氨基塑料除外的负荷轴承木结构的粘结剂-试验法-第1部分:在不同气候条件下垂直于粘结线的长期拉伸载荷试验,垂直于胶线的试样(玻璃屋试验)
简介：This European Standard specifies a method of determining the ability of adhesive bonds to resist long-term sustained load applied vertical to the glue lines. It is applicable to adhesives used in load-bearing timber structures. It is suitable for the following applications: a) for assessing the compliance of adhesives according to EN 15425 and EN 16254; b) for assessing the suitability and quality of adhesives for load-bearing timber structures; c) for assessing the effect on the bond strength resulting from long-term sustained load at cyclic climate conditions. This method is intended primarily to obtain performance data for the classification of adhesives for load bearing timber structures according to their suitability for use in defined climatic environments. This method is not intended to provide data for structural design, and does not necessarily represent the performance of the bonded member in service.
信息：ICS：83.180 CCS：G30 发布：2017-01 实施：

ISO 283-1 CORR 1-2006 织物输送带.全厚度拉伸试验.第1部分:在标准负荷下拉伸强度、拉断伸长及定伸的测定.技术勘误1
简介：
信息：ICS： CCS：J81 发布：2006-11 实施：

ANSI/ASTM E1012-1999 在拉伸负荷下验证样品准直性惯例
简介：Included in this practice are methods covering the determination of the amount of bending that occurs during the application of tensile and compressive forces to notched and unnotched test specimens in the elastic range and to plastic strains less than 0.002. These methods are particularly applicable to the force application rates normally used for tension testing, creep testing, and uniaxial fatigue testing.
信息：ICS：19.060 CCS：A42 发布：1999 实施：1999-08-10

DIN EN ISO 283-2016 织物传送带.全厚度拉伸强度、断裂伸长和基准负荷下伸长的试验方法(ISO 283-2015).德文版本EN ISO 283-2015
简介：
信息：ICS：53.040.20 CCS：J81 发布：2016-04 实施：

DIN EN ISO 22088-2-2006 塑料制品.耐环境应力开裂(ESC)的测定.第2部分:持续拉伸负荷法(ISO 22088-2:2006)
简介：This part of ISO 22088 specifies methods for the determination of environmental stress cracking (ESC) of thermoplastics when they are subjected to a constant tensile load in the presence of chemical agents.It is applicable to test specimens prepared by moulding and/or machining and can be used both for the assessment of ESC of plastic materials exposed to different environments, and for the determination of ESC of different plastic materials exposed to a specific environment.This is essentially a ranking test and is not intended to provide data to be used for design or performanceprediction.NOTE Methods for the determination of environmental stress cracking by means of a constant-strain test are specified in ISO 22088-3, ISO 22088-4 and ISO 22088-5.
信息：ICS：83.080.01 CCS：G31 发布：2006-11 实施：

ASTM D2339-1998(2011) 用拉伸负荷法测定双层胶合板结构中胶粘剂剪切强度特性的标准试验方法
简介：By the nature of the way adhesives are used in two-ply wood construction, shear strength is an important performance criteria. Shear strength measured by this test method is suitable for use in adhesive development, manufacturing quality control, and in materials-performance specifications.1.1 This test method covers the determination of the comparative shear strengths of adhesives when tested on a standard specimen and under specified conditions of preparation, conditioning, and testing. This test method is intended to be applied only to adhesives used in bonding wood to wood. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS： CCS：G38 发布：1998 实施：

GOST ISO 283-2014 橡胶织物输送带. 全厚度拉伸强度, 断裂伸长和基准负荷下伸长的测定
简介：
信息：ICS：53.040.20 CCS：发布：2014 实施：2016-07-01

BS EN ISO 22088-2-2006 塑料.测定耐环境应力破裂性(ESC).恒定拉伸负荷法
简介：This part of ISO 22088 specifies methods for the determination of environmental stress cracking (ESC) of thermoplastics when they are subjected to a constant tensile load in the presence of chemical agents. It is applicable to test specimens prepared by moulding and/or machining and can be used both for the assessment of ESC of plastic materials exposed to different environments, and for the determination of ESC of different plastic materials exposed to a specific environment. This is essentially a ranking test and is not intended to provide data to be used for design or performance prediction. NOTE Methods for the determination of environmental stress cracking by means of a constant-strain test are specified in ISO 22088-3, ISO 22088-4 and ISO 22088-5.
信息：ICS：83.080.01 CCS：G30 发布：2006-09-29 实施：2006-09-29

ASTM D2339-1998(2004) 用拉伸负荷法测定双层胶合板结构中胶粘剂剪切强度特性的标准试验方法
简介：By the nature of the way adhesives are used in two-ply wood construction, shear strength is an important performance criteria. Shear strength measured by this test method is suitable for use in adhesive development, manufacturing quality control, and in materials-performance specifications.1.1 This test method covers the determination of the comparative shear strengths of adhesives when tested on a standard specimen and under specified conditions of preparation, conditioning, and testing. This test method is intended to be applied only to adhesives used in bonding wood to wood.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS： CCS：B70 发布：1998 实施：

GOST ISO 283-2014 橡胶织物输送带. 全厚度拉伸强度, 断裂伸长和基准负荷下伸长的测定
简介：
信息：ICS：53.040.20 CCS：G42 发布：2014 实施：2016-07-01

EN ISO 22088-2-2006 塑料.测定耐环境应力破裂性(ESC).第2部分:恒定拉伸负荷法 ISO 22088-2-2006;-1997
简介：This part of ISO 22088 specifies methods for the determination of environmental stress(ESC) of thermoplastics when they are subjected to a constant tensile load in the presence of chemical agents.It is applicable to test specimens prepared by moulding and/or machining and can be used both for the assessment of ESC of plastic materials exposed to different environments,and for the determination of ESC of different plastic materials exposed to a specific environment.This is essentially a ranking test and is not intended to provide data to be used for design or performance prediction.
信息：ICS：83.080.01 CCS：发布：2006-08-01 实施：

ASTM D2339-1998 用拉伸负荷法测定双层胶合板结构中胶粘剂剪切强度特性的标准试验方法
简介：1.1 This test method covers the determination of the comparative shear strengths of adhesives when tested on a standard specimen and under specified conditions of preparation, conditioning, and testing. This test method is intended to be applied only to adhesives used in bonding wood to wood. 1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：83.180 (Adhesives) CCS：B70 发布：1998 实施：

KS M ISO 6237-2013 黏合剂.木材与木材黏结体.用拉伸负荷测定剪切强度
简介：이 표준은 인장이 적용되는 표준 시료와 준비, 상태, 실험의 특정한 조건 아래에서 목재 대 목재 접착제의 전단 강도를 측정하는 방법에 대해 규정한다. 이 방법은 평행한 얇은 판이거나 교차한 얇은판에서 목재 대 목재 접착에 사용된 접착제를 시험한 것에 대해서만 적용한다.
信息：ICS：83.180 CCS：G38 发布：2013-12-31 实施：2013/12/31

ISO 22088-2-2006 塑料制品.耐环境应力开裂(ESC)测定.第2部分:恒定拉伸负荷法
简介：This part of ISO 22088 specifies methods for the determination of environmental stress cracking (ESC) of thermoplastics when they are subjected to a constant tensile load in the presence of chemical agents.It is applicable to test specimens prepared by moulding and/or machining and can be used both for the assessment of ESC of plastic materials exposed to different environments, and for the determination of ESC of different plastic materials exposed to a specific environment.This is essentially a ranking test and is not intended to provide data to be used for design or performance prediction.NOTE Methods for the determination of environmental stress cracking by means of a constant-strain test are specified in ISO 22088-3, ISO 22088-4 and ISO 22088-5.
信息：ICS：83.080.01 CCS：G31 发布：2006-08 实施：

ASTM D3164-1997 用拉伸负荷法测定胶粘剂粘接塑料搭接接头剪切强度特性的标准试验方法
简介：1.1 This test method is intended to complement Test Method D1002 and extend its application to single-lap-shear adhesive joints employing plastic adherends. The test method is useful for generating comparative shear strength data for joints made from a number of plastics. It can also provide a means by which several plastics surface treatments can be compared. 1.2 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of whoever uses this standard to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：83.180 (Adhesives) CCS：G38 发布：1997 实施：

KS M ISO 6237-2013(2018) 胶粘剂.木材对木材胶粘剂.用拉伸负荷测定剪切强度
简介：
信息：ICS：83.180 CCS：发布：2013-12-31 实施：

ASTM D5397-99(2005) 用缺口恒拉伸负荷试验评定聚烯烃土工膜抗应力开裂性的标准试验方法
简介：
信息：ICS：59.080.70 CCS：发布：2005-06-01 实施：

GOST ISO 1924-1-1996 纸与纸板.拉伸强度的测定方法.第1部分.恒定速度负荷法
简介：Настоящий стандарт распространяется на бумагу и картон и устанавливает метод определения прочности на разрыв и удлинения при растяжении
信息：ICS：85.060 CCS：发布：1996 实施：2000-01-01

TIA-455-33-B-2005 FOTP-33 光缆的拉伸负荷和折弯测试
简介：This test is intended to verify the ability of an optical fiber cable to perform satisfactorily asrequired by Detail Specifications (a) while undergoing tensile and bending forces and(b) after undergoing tensile and bending forces.
信息：ICS： CCS：M33 发布：2005-01-10 实施：

NF L17-956-1995 航空工业.飞机结构用合成纤维布.测定布和无涂层布在交货条件下拉伸试验时的断裂负荷和拉伸率
简介：
信息：ICS：49.045 CCS：V13 发布：1995-05-01 实施：1995-05-05

NF P12-605-5-2013 砖石结构辅助部件试验方法.第5部分:壁锚的拉伸和压缩负荷能力及满载排水量特性的测定(对联试验)
简介：
信息：ICS：91.080.30 CCS：P24 发布：2013-02-02 实施：2013-02-02

BS ISO 6237-2003 粘合剂.木材与木材粘结体.用拉伸负荷测定剪切强度
简介：This International Standard specifies a method for determining the shear strength of wood-to-wood adhesive bonds, with a standard specimen loaded in tension and under specified conditions of preparation, conditioning and testing. This method is intended for testing only those adhesives used in bonding wood to wood in either parallel-laminated or cross-laminated construction. NOTE 1 To carry out this test, basic information regarding certain variables is needed by the test laboratory (see Annex A). NOTE 2 This method is not intended for use in testing manufactured products.
信息：ICS：83.180 CCS：G38 发布：2003-10-31 实施：2003-10-31

GOST 16218.5-1993 服饰纺织品.断裂负荷和拉伸时的断裂延伸率测定法
简介：Настоящий стандарт распространяется на все виды тканых, плетеных, витых и вязаных метражных текстильно-галантерейных изделий (ленты, тесь
信息：ICS：61.040 CCS：发布：1993 实施：1995-01-01

ASTM D5397-07(2012) 用缺口恒拉伸负荷试验评定聚烯烃土工膜抗应力开裂性的标准试验方法
简介：
信息：ICS：59.080.70 CCS：发布：2012-07-01 实施：

ISO 6237-2003 粘合剂.木材与木材粘结体.用拉伸负荷测定剪切强度
简介：This International Standard specifies a method for determining the shear strength of wood-to-wood adhesive bonds, with a standard specimen loaded in tension and under specified conditions of preparation, conditioning and testing. This method is intended for testing only those adhesives used in bonding wood to wood in either parallel-laminated or cross-laminated construction.NOTE 1 To carry out this test, basic information regarding certain variables is needed by the test laboratory (see Annex A). NOTE 2 This method is not intended for use in testing manufactured products.
信息：ICS：83.180 CCS：G38 发布：2003-10 实施：

GOST 19712-1989 针织品.在小于断裂负荷下断裂性和拉伸性测定法
简介：Настоящий стандарт распространяется на трикотажные изделия из всех видов пряжи и нитей и устанавливает методы определения: разрывных хар
信息：ICS：61.020 CCS：发布：1989 实施：1991-01-01

KS M 3734-2011 用拉伸负荷测定黏合剂剪切强度
简介：이 표준은 접착제의 인장 전단 접착 강도 시험방법에 대하여 규정한다.
信息：ICS：83.18 CCS：G38 发布：2011-12-23 实施：2011-12-23

KS M ISO 6237-2003 黏合剂.木材与木材黏结体.用拉伸负荷测定剪切强度
简介：이 규격은 인장이 적용되는 표준 시료와 준비, 상태, 실험의 특정한 조건 아래에서 목재
信息：ICS：83.18 CCS：G38 发布：2003-07-29 实施：2003-07-29

ISO 6237-1987 粘合剂木材与木材粘结体用拉伸负荷测定剪切强度
简介：
信息：ICS：6770 CCS：G38 发布：1987-03 实施：

prEN 2002-3-1978 金属材料试验方法.第3部分:拉伸试验机的负荷校验.航空系列
简介：
信息：ICS： CCS：N71 发布：1978-04 实施：

DIN ISO 2285-2010 硫化橡胶或热塑橡胶. 在恒定伸长率作用下的永久变形和恒定拉伸负荷下的永久变形, 伸长率及蠕变（ISO 2285: 2007）
简介：
信息：ICS：83.060 CCS：G34 发布：2010-07 实施：

ASTM D3164M-2003 用拉伸负荷法测定胶粘剂粘接塑料搭接接头剪切强度性能的试验方法(米制)
简介：1.1 This test method is intended to complement Test Method D 1002 and D 3163 and extend its application to single-lap-shear adhesive joints employing plastic adherends. The test method is useful for generating comparative shear strength data for joints made from a number of plastics. It can also provide a means by which several plastics surface treatments can be compared.1.2 The values stated in SI units are to be regarded as the standard.Note 18212;A soft metric (conversion from English) companion to Test Method D 3164M has been developed - D 3164.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：83.080.01 CCS：G38 发布：2003 实施：

PN H04327-1974 金属疲劳测试．恒定循环负荷下的拉伸．压缩测试
简介：Przedmiotem normyjest pró-ba zm?czenia metali w przypadku wahad?owego ross-ci?gania-?ciskania lub t?tni?cego rozci?gania lub ?ciskania o przebiegu sinusoidalnym próbek g?adkich lub próbek z karbem, wyci?tych z walco-wanych wyrobów hutniczych (pr?tów, kszta?towników i blach) z odkuwek, z odlewów lub próbek wyci?tych z cz??ci maszyn i urz?dzeń.
信息：ICS： CCS：发布：1974 实施：