蜡烛检测标准蜡烛-中析研究所检测

(CMA)

(CNAS)

(ISO)

(高新技术企业)

蜡烛相关标准参考信息

GB/T 22256-2008 果冻蜡烛
简介：本标准规定了果冻蜡烛的术语和定义、要求、试验方法、检验规则及标志、包装、运输、贮存。本标准适用于果冻蜡烛产品。
信息：ICS：71.100.35 CCS：Y44 发布：2008-07-31 实施：2009-05-01

ASTM F1972-16 蜡烛及相关附件术语的标准指南
简介：
信息：ICS：01.040.71 CCS：发布：2016-05-01 实施：

QB/T 4362-2012 蜡制品.蜡烛用石蜡
简介：本标准规定了蜡烛用石蜡的技术要求、试验方法、检验规则和标志、包装、运输、贮存及保质期。本标准适用于以含油蜡为原料，经发汗或溶剂脱油，再经白土或加氢精制所得到的蜡烛用石蜡。
信息：ICS：75.140 CCS：E42 发布：2012-11-07 实施：2013-03-01

T/ZJRHXH 0006-2022 天然装饰物香薰蜡烛
简介：本标准主要规定了天然装饰物香薰蜡烛的原料、技术要求、试验方法、检验规则、标志、包装、运输、贮存和保质期的内容。
信息：ICS：71.100.99 CCS：C268 发布：2022-03-25 实施：2022-03-25

ASTM F2417-16 蜡烛防火安全标准规范
简介：
信息：ICS：13.220.20 CCS：发布：2016-05-01 实施：

QB/T 4359-2012 茶蜡蜡烛
简介：本标准规定了茶蜡蜡烛的术语和定义、要求、试验方法、检验规则、标志、包装、运输、贮存、保质期。本标准适用于茶蜡蜡烛产品。
信息：ICS：71.100.35 CCS：Y44 发布：2012-11-07 实施：2013-03-01

T/ZJRHXH 0003-2022 异形香薰蜡烛检测方法
简介：本标准规定了异形香薰蜡烛的检测准备、感官测试、理化测试和安全测试的方法。
信息：ICS：71.100.99 CCS：C268 发布：2022-03-25 实施：2022-03-25

ASTM F2601-16 蜡烛配件消防安全标准规范
简介：
信息：ICS：71.100.99 CCS：发布：2016-02-01 实施：

CFR 7-3201.79-2014 农业. 第3201部分:指南指定材料的联邦采购. 第B子部分:指定类别的产品和中间体或原料. 第3201.79节:蜡烛和蜡融化.
简介：(a) Definition. Products composed of a solid mass and either an embedded wick that is burned to provide light or aroma, or that are wickless and melt when heated to produce an aroma.
信息：ICS： CCS：B00 发布：2012-04-14 实施：2012-04-14

T/ZJRHXH 0001-2022 罐装香熏蜡烛检测方法
简介：本标准主要规定了罐装香薰蜡烛的检测准备、感官测试、理化测试和安全测试的检测方法。
信息：ICS：71.100.99 CCS：C268 发布：2022-03-25 实施：2022-03-25

ASTM F1972-2016 与蜡烛和相关辅助用品相关的术语的标准指南
简介：4.1x00a0;This guide is used to establish a set of definitions that allows manufacturers, consumers, retailers, and the scientific community to use a common language to define candles and associated accessory items. 1.1x00a0;This guide defines standard terms used to describe candles and associated accessory products. 1.2x00a0;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are for information only.
信息：ICS：01.040.71 CCS：发布：2016 实施：

ASTM D2863-12 支持塑料蜡烛状燃烧的最小氧浓度测量的标准试验方法（氧指数）
简介：
信息：ICS：83.080.01 CCS：发布：2012-04-01 实施：

T/ZJRHXH 0002-2022 柱形香薰蜡烛检测方法
简介：本标准主要描述了柱形香薰蜡烛的检测准备、感官测试、理化测试和安全测试的检测方法。
信息：ICS：71.100.99 CCS：C268 发布：2022-03-25 实施：2022-03-25

ASTM F2417-2016 蜡烛防火安全用标准规格
简介：1.1x00a0;This specification is intended to prescribe minimum safety requirements for candles to provide a reasonable degree of safety for normal use with candles, thereby improving personal safety and reducing fires, deaths, and injuries. 1.2x00a0;This specification is not intended to replace other important safety practices that should be in place, such as adult supervision, close monitoring, fire detection, alarm or suppression systems, and use of candles away from combustible materials. 1.3x00a0;Flame-producing devices, such as candles, present a potential hazard to the user. This specification cannot eliminate all hazards, but will minimize the potential hazards of candles to the user. 1.4x00a0;This specification is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions. 1.5x00a0;This standard is used to predict or provide a quantitative measure of the fire hazard from a specified set of fire conditions involving specific materials, products, or assemblies. This assessment does not necessarily predict the hazard of actual fires which involve conditions other than those assumed in the analysis. 1.6x00a0;Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests. 1.7x00a0;This specification states values in SI units which are to be regarded as the standard. The values given in parenthesis are for information only. 1.8x00a0;This specification does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.
信息：ICS：13.220.20 CCS：发布：2016 实施：

ASTM D2863-12e1 支持塑料蜡烛状燃烧的最小氧浓度测量的标准试验方法（氧指数）
简介：
信息：ICS：83.080.01 CCS：发布：2012-04-01 实施：

T/QGCML 251-2022 祛甲醛香芬蜡烛
简介：本文件规定了祛甲醛香芬蜡烛的术语定义、生产流程、基本要求、试验方法、检验规则、标志、包装、运输及贮存。本文件适用于制造祛甲醛香芬蜡烛的企业。
信息：ICS：71.100.35 CCS：C268 发布：2022-01-11 实施：2022-01-12

ASTM F2601-2016 蜡烛附件防火安全用标准规格
简介：1.1x00a0;This specification prescribes minimum safety requirements for candle accessories to help ensure a reasonable degree of safety for normal use with candles, thereby improving personal safety and reducing fires, deaths, and injuries. 1.2x00a0;This specification is not intended to replace other safety practices such as adult supervision, close monitoring of product when in use, and fire detection, alarm, or suppression systems. 1.3x00a0;The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4x00a0;This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions. 1.5x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：97.180 CCS：发布：2016 实施：

ASTM F2601-12 蜡烛配件消防安全标准规范
简介：
信息：ICS：97.180 CCS：发布：2012-03-01 实施：

T/QGCML 252-2022 祛异味香芬蜡烛
简介：本文件规定了祛异味香芬蜡烛的术语定义、生产流程、基本要求、试验方法、检验规则、标志、包装、运输及贮存。本文件适用于制造祛异味香芬蜡烛的企业。
信息：ICS：71.100.35 CCS：C268 发布：2022-01-11 实施：2022-01-12

ASTM F2326-04(2015) 用于收集和分析蜡烛可燃排放的标准测试方法
简介：
信息：ICS：13.040.40 CCS：发布：2015-01-01 实施：

ASTM D2863-2012 测量支持塑料蜡烛式燃烧的最低需氧浓度的标准试验方法
简介：This test method provides for the measuring of the minimum concentration of oxygen in a flowing mixture of oxygen and nitrogen that will just support flaming combustion of plastics. Correlation with burning characteristics under actual use conditions is not implied. In this test method, the specimens are subjected to one or more specific sets of laboratory test conditions. If different test conditions are substituted or the end-use conditions are changed, it is not always possible by or from this test to predict changes in the fire-test-response characteristics measured. Therefore, the results are valid only for the fire-test-exposure conditions described in this test method.1.1 This fire-test-response standard describes a procedure for measuring the minimum concentration of oxygen, expressed as percent volume, that will just support flaming combustion in a flowing mixture of oxygen and nitrogen. 1.2 This test method provides three testing procedures. Procedure A involves top surface ignition, Procedure B involves propagating ignition, and Procedure C is a short procedure involving the comparison with a specified minimum value of the oxygen index. 1.3 Test specimens used for this test method are prepared into one of six types of specimens (see Table 1). 1.4 This test method provides for testing materials that are structurally self-supporting in the form of vertical bars or sheet up to 10.5-mm thick. Such materials are solid, laminated or cellular materials characterized by an apparent density greater than 15 kg/m3. 1.5 This test method also provides for testing flexible sheet or film materials, while supported vertically. 1.6 This test method is also suitable, in some cases, for cellular materials having an apparent density of less than 15 kg/m3. Note 18212;Although this test method has been found applicable for testing some other materials, the precision of the test method has not been determined for these materials, or for specimen geometries and test conditions outside those recommended herein. 1.7 This test method measures and describes the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions. 1.8 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific hazards statement are given in Section 10. 1.10 Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests. Note 28212;This test method and ISO 4589-2 are technically equivalent when using the gas measurement and control device described in 6.3.1, with direct oxygen concentration measurement. TABLE 1 Test Specimen Dimensions Test Specimen TypeADimensionsMaterial Form
信息：ICS：83.080.01 (Plastics in general) CCS：G31 发布：2012 实施：

ASTM F2058-07(2021) 蜡烛消防安全标准规范
简介：
信息：ICS：13.200 CCS：发布：2021-02-01 实施：

ASTM F2058-07(2014) 蜡烛消防安全标准规范
简介：
信息：ICS：13.200 CCS：发布：2014-10-01 实施：

ASTM F2601-2012 蜡烛配件防火安全的标准规格
简介：1.1 This specification prescribes minimum safety requirements for candle accessories to help ensure a reasonable degree of safety for normal use with candles, thereby improving personal safety and reducing fires, deaths, and injuries. 1.2 This specification is not intended to replace other safety practices such as adult supervision, close monitoring of product when in use, and fire detection, alarm, or suppression systems. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：97.180 (Miscellanous domestic and commercial equip CCS：发布：2012 实施：

ASTM F2326-04(2021) 用于收集和分析蜡烛可燃排放的标准测试方法
简介：
信息：ICS：13.040.40 CCS：发布：2021-02-01 实施：

KS M 2722-2014(2019) 蜡烛
简介：
信息：ICS：71.100.01 CCS：发布：2014-09-23 实施：

ASTM D2863-2012e1 测量支持塑料蜡烛式燃烧的最低需氧浓度的标准试验方法
简介：5. Significance and UseTop Bottom 5.1 This test method provides for the measuring of the minimum concentration of oxygen in a flowing mixture of oxygen and nitrogen that will just support flaming combustion of plastics. Correlation with burning characteristics under actual use conditions is not implied. 5.2 In this test method, the specimens are subjected to one or more specific sets of laboratory test conditions. If different test conditions are substituted or the end-use conditions are changed, it is not always possible by or from this test to predict changes in the fire-test-response characteristics measured. Therefore, the results are valid only for the fire-test-exposure conditions described in this test method. 1.1 This fire-test-response standard describes a procedure for measuring the minimum concentration of oxygen, expressed as percent volume, that will just support flaming combustion in a flowing mixture of oxygen and nitrogen. 1.2 This test method provides three testing procedures. Procedure A involves top surface ignition, Procedure B involves propagating ignition, and Procedure C is a short procedure involving the comparison with a specified minimum value of the oxygen index. 1.3 Test specimens used for this test method are prepared into one of six types of specimens (see Table 1). TABLE 1 Test Specimen Dimensions Test Specimen TypeA Dimensions Material Form Length, mm Width, mm Thickness, mm
信息：ICS：83.080.01 (Plastics in general) CCS：G31 发布：2012 实施：

T/QXBQ 0006-2020 玻璃蜡烛台
简介：本标准规定了玻璃蜡烛台的术语和定义、要求、试验方法、检验规则和标志、包装、运输、贮存。
信息：ICS：81.040.30 CCS：C305 发布：2020-06-10 实施：2020-06-10

ASTM F2179-14 生产用作蜡烛容器的退火苏打石灰硅酸盐玻璃容器的标准规范
简介：
信息：ICS：81.040.30 CCS：发布：2014-01-15 实施：

ASTM F2417-11 蜡烛防火安全标准规范
简介：
信息：ICS：13.220.20 CCS：发布：2011-10-01 实施：

ASTM F2179-20 生产用作蜡烛容器的退火苏打石灰硅酸盐玻璃容器的标准规范
简介：
信息：ICS：81.040.30 CCS：发布：2020-03-01 实施：

SN/T 3839-2014 进出口蜡烛燃烧过程中生成炭黑的测定方法
简介：本标准规定了蜡烛燃烧过程中生成炭黑的测定方法。本标准适用于室内使用的直径100 mm以下的单芯蜡烛,在燃烧过程中生成的炭黑量的测定。
信息：ICS： CCS：发布：2014-01-13 实施：2014-08-01

IEC TS 62441-2011 防止音频/视频、通信和信息技术设备意外点燃蜡烛火焰的防护措施
简介：
信息：ICS：97.020 CCS：发布：2011-02-10 实施：

T/ZZB 1433-2019 环保香氛罐装蜡烛
简介：本标准规定了环保香氛罐装蜡烛（以下简称：蜡烛）的术语和定义、基本要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存和质量承诺。本标准适用于室内使用，以植物蜡（棕榈油脂、豆蜡等）为主要原料，加入香精，在燃烧过程中有香味散发、无可视烟，灌装于固定容器中的蜡烛。
信息：ICS：71.100.35 CCS：C268 发布：2019-12-18 实施：2020-01-17

ASTM F2179-2014 用作蜡烛台而生产的退火钠钙硅酸盐玻璃容器的标准规范
简介：1.1x00a0;This specification covers the minimum requirements for annealed soda-lime-silicate glass containers when the producer knows the containers are to be used as candle containers. 1.2x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.
信息：ICS：81.040.30 (Glass products) CCS：A82 发布：2014 实施：

IEC TS 62441:2011 防止音频/视频、通信和信息技术设备意外点燃蜡烛火焰的防护措施
简介：
信息：ICS：97.020 CCS：发布：2011-02-10 实施：

ASTM D2863-19 支持塑料蜡烛状燃烧的最小氧浓度测量的标准试验方法（氧指数）
简介：
信息：ICS：83.080.01 CCS：发布：2019-10-01 实施：

GOST IEC/TS 62441-2014 音频/视频, 通信和信息技术设备因蜡烛点燃引起的意外事故保护措施
简介：
信息：ICS：13.220.40;33.020;35.020 CCS：M72 发布：2014 实施：2016-11-01

IEC TS 62441-2011 音频/视频,通讯和信息技术设备因蜡烛点燃引起的意外事故保护措施
简介：
信息：ICS：13.220.40;33.020;35.020;35.260;97.020 CCS：C80 发布：2011-02 实施：

ASTM F1972-19 蜡烛及相关附件术语的标准指南
简介：
信息：ICS：01.040.71 CCS：发布：2019-04-01 实施：

ASTM D2863-13 支持塑料蜡烛状燃烧的最小氧浓度测量的标准试验方法（氧指数）
简介：
信息：ICS：83.080.01 CCS：发布：2013-09-01 实施：

ASTM F2417-2011 蜡烛的防火安全的标准规格
简介：1.1 This specification is intended to prescribe minimum safety requirements for candles to provide a reasonable degree of safety for normal use with candles, thereby improving personal safety and reducing fires, deaths, and injuries. 1.2 This specification is not intended to replace other important safety practices that should be in place, such as adult supervision, close monitoring, fire detection, alarm or suppression systems, and use of candles away from combustible materials. 1.3 Flame-producing devices, such as candles, present a potential hazard to the user. This specification cannot eliminate all hazards, but will minimize the potential hazards of candles to the user. 1.4 This specification is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions. 1.5 This standard is used to predict or provide a quantitative measure of the fire hazard from a specified set of fire conditions involving specific materials, products, or assemblies. This assessment does not necessarily predict the hazard of actual fires which involve conditions other than those assumed in the analysis. 1.6 Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests. 1.7 This specification states values in SI units which are to be regarded as the standard. The values given in parenthesis are for information only. 1.8 This specification does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.
信息：ICS：97.180 (Miscellanous domestic and commercial equip CCS：Y89 发布：2011 实施：

ASTM D2863-17a 支持塑料蜡烛状燃烧的最小氧浓度测量的标准试验方法（氧指数）
简介：
信息：ICS：83.080.01 CCS：发布：2017-12-01 实施：

ASTM F1972-13 蜡烛及相关附件术语的标准指南
简介：
信息：ICS：01.040.71 CCS：发布：2013-09-01 实施：

DIN CLC/TS 62441-2010 音频/视频、通讯和信息技术设备因蜡烛点燃引起的意外事故
简介：
信息：ICS： CCS：C80 发布：2010-05 实施：2010-05-01

DB14/T 1451-2017 玻璃蜡烛台
简介：
信息：ICS：81.040.30 CCS：Y 22 发布：2017-11-20 实施：2018-01-20

ASTM F2179-02(2013) 生产用作蜡烛容器的退火苏打石灰硅酸盐玻璃容器的标准规范
简介：
信息：ICS：81.040.30 CCS：发布：2013-07-01 实施：

SN/T 2496-2010 出口蜡烛检验规程
简介：本标准规定了出口蜡烛的抽样、检验、结果判定和不合格处置。本标准适用于出口蜡烛的检验。
信息：ICS： CCS：Y89 发布：2010-03-02 实施：2010-09-16

ASTM F2417-17 蜡烛防火安全标准规范
简介：
信息：ICS：13.220.20 CCS：发布：2017-10-01 实施：

ASTM F2601-13 蜡烛配件消防安全标准规范
简介：
信息：ICS：97.180 CCS：发布：2013-07-01 实施：

ASTM D2863-2010 测定支持塑料的蜡烛式燃烧的最小氧浓度的标准试验方法
简介：This test method provides for the measuring of the minimum concentration of oxygen in a flowing mixture of oxygen and nitrogen that will just support flaming combustion of plastics. Correlation with burning characteristics under actual use conditions is not implied. In this test method, the specimens are subjected to one or more specific sets of laboratory test conditions. If different test conditions are substituted or the end-use conditions are changed, it is not always possible by or from this test to predict changes in the fire-test-response characteristics measured. Therefore, the results are valid only for the fire-test-exposure conditions described in this test method.1.1 This fire-test-response standard describes a procedure for measuring the minimum concentration of oxygen, expressed as percent volume, that will just support flaming combustion in a flowing mixture of oxygen and nitrogen. 1.2 This test method provides three testing procedures. Procedure A involves top surface ignition, Procedure B involves propagating ignition, and Procedure C is a short procedure involving the comparison with a specified minimum value of the oxygen index. 1.3 Test specimens used for this test method are prepared into one of six types of specimens (see Table 1). 1.4 This test method provides for testing materials that are structurally self-supporting in the form of vertical bars or sheet up to 10.5-mm thick. Such materials are solid, laminated or cellular materials characterized by an apparent density greater than 15 kg/m3. 1.5 This test method also provides for testing flexible sheet or film materials, while supported vertically. 1.6 This test method is also suitable, in some cases, for cellular materials having an apparent density of less than 15 kg/m3. Note 18212;Although this test method has been found applicable for testing some other materials, the precision of the test method has not been determined for these materials, or for specimen geometries and test conditions outside those recommended herein. 1.7 This test method measures and describes the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions. 1.8 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：83.080.01 CCS：G31 发布：2010 实施：

ASTM D2863-17 支持塑料蜡烛状燃烧的最小氧浓度测量的标准试验方法（氧指数）
简介：
信息：ICS：83.080.01 CCS：发布：2017-08-15 实施：

ASTM D2863-2013 测量支持塑料蜡烛式燃烧的最低需氧浓度的标准试验方法
简介：5.1x00a0;This test method provides for the measuring of the minimum concentration of oxygen in a flowing mixture of oxygen and nitrogen that will just support flaming combustion of plastics. Correlation with burning characteristics under actual use conditions is not implied. 5.2x00a0;In this test method, the specimens are subjected to one or more specific sets of laboratory test conditions. If different test conditions are substituted or the end-use conditions are changed, it is not always possible by or from this test to predict changes in the fire-test-response characteristics measured. Therefore, the results are valid only for the fire-test-exposure conditions described in this test method. 1.1x00a0;This fire-test-response standard describes a procedure for measuring the minimum concentration of oxygen, expressed as percent volume, that will just support flaming combustion in a flowing mixture of oxygen and nitrogen. 1.2x00a0;This test method provides three testing procedures. Procedure A involves top surface ignition, Procedure B involves propagating ignition, and Procedure C is a short procedure involving the comparison with a specified minimum value of the oxygen index. 1.3x00a0;Test specimens used for this test method are prepared into one of six types of specimens (see Table 1). TABLE 1 Test Specimen Dimensions Test Specimen TypeA Dimensions Material Form Length, mm Width, mm Thickness, mm x00a0; I 80 to 150 10 x00b1; 0.5 4 x00b1; 0.25 ......
信息：ICS：83.080.01 (Plastics in general) CCS：G31 发布：2013 实施：

ASTM D2863-09 支持塑料蜡烛状燃烧的最小氧浓度测量的标准试验方法（氧指数）
简介：
信息：ICS：83.080.01 CCS：发布：2009-09-01 实施：

ASTM D2863-2017 测量支持塑料蜡烛式燃烧最低需氧浓度的标准试验方法(氧指数)
简介：5.1x00a0;This test method provides for the measuring of the minimum concentration of oxygen in a flowing mixture of oxygen and nitrogen that will just support flaming combustion of plastics. Correlation with burning characteristics under actual use conditions is not implied. 5.2x00a0;In this test method, the specimens are subjected to one or more specific sets of laboratory test conditions. If different test conditions are substituted or the end-use conditions are changed, it is not always possible by or from this test to predict changes in the fire-test-response characteristics measured. Therefore, the results are valid only for the fire-test-exposure conditions described in this test method. 1.1x00a0;This fire-test-response standard describes a procedure for measuring the minimum concentration of oxygen, expressed as percent volume, that will just support flaming combustion in a flowing mixture of oxygen and nitrogen. 1.2x00a0;This test method provides three testing procedures. Procedure A involves top surface ignition, Procedure B involves propagating ignition, and Procedure C is a short procedure involving the comparison with a specified minimum value of the oxygen index. 1.3x00a0;Test specimens used for this test method are prepared into one of six types of specimens (see Table 1). TABLE 1 Test Specimen Dimensions Test Specimen TypeA Dimensions Material Form Length, mm Width, mm
信息：ICS：83.080.01 CCS：G30 发布：2017 实施：

ASTM F2601-2013 蜡烛附件防火安全用标准规范
简介：1.1x00a0;This specification prescribes minimum safety requirements for candle accessories to help ensure a reasonable degree of safety for normal use with candles, thereby improving personal safety and reducing fires, deaths, and injuries. 1.2x00a0;This specification is not intended to replace other safety practices such as adult supervision, close monitoring of product when in use, and fire detection, alarm, or suppression systems. 1.3x00a0;The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4x00a0;This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions. 1.5x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：97.180 (Miscellanous domestic and commercial equip CCS：发布：2013 实施：

ASTM D2863-10 支持塑料蜡烛状燃烧的最小氧浓度测量的标准试验方法（氧指数）
简介：
信息：ICS：83.080.01 CCS：发布：2009-09-01 实施：

ASTM F2601-16a 蜡烛配件消防安全标准规范
简介：
信息：ICS：71.100.99 CCS：发布：2016-07-01 实施：

ASTM F1972-2013 蜡烛及蜡烛附件的相关术语用标准指南
简介：4.1x00a0;This guide is used to establish a set of definitions that allows manufacturers, consumers, retailers, and the scientific community to use a common language to define candles and associated accessory items. 1.1x00a0;This guide defines standard terms used to describe candles and associated accessory products. 1.2x00a0;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are for information only.
信息：ICS：01.040.71 (Chemical technology (Vocabularies)); 71 CCS：发布：2013 实施：

ASTM F2326-04(2009) 用于收集和分析蜡烛可燃排放的标准测试方法
简介：
信息：ICS：13.040.40 CCS：发布：2009-08-01 实施：