机械测试标准检测标准机械测试标准-中析研究所检测

(CMA)

(CNAS)

(ISO)

(高新技术企业)

机械测试标准相关标准参考信息

DIN EN ISO 9902-6-2021 纺织机械. 噪声测试标准. 第6部分: 织造机械(ISO 9902-6-2018); 德文版本EN ISO 9902-6-2021
简介：This document specifies the mounting, operating and measuring conditions required for the measurement, declaration and verification of noise emitted by different types of spinning preparatory and spinning machines. It considers measurement on the complete machine consisting of th
信息：ICS：17.140.20 CCS：Z32 发布：2021-04-00 实施：

ASTM E2769-16 使用三点弯曲和受控加载速度的热机械分析的弹性模量的标准测试方法
简介：
信息：ICS：29.035.20 CCS：发布：2016-04-01 实施：

ASTM A1058-2014 钢产品机械测试的标准试验方法. 米制
简介：1.1x00a0;These test methods cover mechanical tests described in ASTM, EN,2 ISO,3 and JIS4 standards that utilize the SI system of units. The test methods in each system are not exact equivalents. Each standards system (ASTM, EN, ISO, and JIS) shall be used independently of the other. Combining requirements from any two or more systems may result in nonconformance with the purchase order. 1.2x00a0;These test methods cover procedures for the mechanical testing of steels, stainless steels, and related alloys. The various mechanical tests herein described are used to determine properties required in the product specifications. Variations in testing methods are to be avoided, and standard methods of testing are to be followed to obtain reproducible and comparable results. In those cases in which the testing requirements for certain products are unique or at variance with these general procedures, the product specification testing requirements shall control. 1.3x00a0;Only one of the testing procedure tracks shall be followed: ASTM, EN, ISO, or JIS. When a test method or practice is not available in one of the tracks then an appropriate test method or practice from an alternative track shall be used. The respective tests are listed in the column shown in Table 1.TABLE 1 Tests and Applicable Standards Test Sections ASTM EN ISO JIS Tension 5 to 12 E8/E8M 10002-1 6892-1 Z 2241
信息：ICS：77.040.10 (Mechanical testing of metals) CCS：H22 发布：2014 实施：

ASTM E2206-21 热机械分析仪的力校准标准测试方法
简介：
信息：ICS：71.040.50 CCS：发布：2021-03-01 实施：

ANSI/AWS B4.0-2016 焊缝的机械测试用标准方法
简介：
信息：ICS： CCS：J33 发布：2016-01-01 实施：

ASTM B877-96(2013) 通过磷钼酸（PMA）方法对金属涂层的总体缺陷和机械损伤的标准测试方法
简介：
信息：ICS：25.220.40 CCS：发布：2013-12-01 实施：

ASTM D5459-95(2020) 机械方向弹性恢复和拉伸膜的永久变形和应力保持的标准测试方法
简介：
信息：ICS：55.040 CCS：发布：2020-11-01 实施：

ASTM E6-15e4 与机械测试方法有关的标准术语
简介：
信息：ICS：01.040.19 CCS：发布：2015-12-01 实施：

ASTM E1824-13 使用热机械分析玻璃化转变温度的标准测试方法:张力法
简介：
信息：ICS：17.200.10 CCS：发布：2013-08-01 实施：

ASTM B362-91(2020) 温控金属螺旋线圈机械扭矩的标准测试方法
简介：
信息：ICS：29.120.20 CCS：发布：2020-10-01 实施：

ASTM E6-15 与机械测试方法有关的标准术语
简介：
信息：ICS：01.040.19 CCS：发布：2015-12-01 实施：

ASTM D5895-13 使用机械记录仪评估有机涂层成膜期间干燥或固化的标准测试方法
简介：
信息：ICS：25.220.60 CCS：发布：2013-06-01 实施：

ASTM D7187-20 通过纳米尺度测量油漆涂层的划痕/ Mar行为的机械方面的标准测试方法
简介：
信息：ICS：87.040 CCS：发布：2020-06-01 实施：

ASTM E6-15e2 与机械测试方法有关的标准术语
简介：
信息：ICS：01.040.19 CCS：发布：2015-12-01 实施：

ASTM E2769-13 使用三点弯曲和受控加载速度的热机械分析的弹性模量的标准测试方法
简介：
信息：ICS：29.035.20 CCS：发布：2013-05-15 实施：

ASTM E1824-19 使用热机械分析玻璃化转变温度的标准测试方法:张力法
简介：
信息：ICS：17.200.10 CCS：发布：2019-09-01 实施：

ASTM E6-15e3 与机械测试方法有关的标准术语
简介：
信息：ICS：01.040.19 CCS：发布：2015-12-01 实施：

ASTM D4781-03(2013) 精细催化剂颗粒和催化剂载体颗粒的机械攻丝包装密度的标准测试方法
简介：
信息：ICS：71.040.30 CCS：发布：2013-03-01 实施：

ASTM E1830-15(2019) 确定光伏组件机械完整性的标准测试方法
简介：
信息：ICS：27.160 CCS：发布：2019-04-01 实施：

ASTM E6-15e1 与机械测试方法有关的标准术语
简介：
信息：ICS：01.040.19 CCS：发布：2015-12-01 实施：

ASTM A370-2013 钢制品机械测试的标准试验方法和定义
简介：3.1x00a0;The primary use of these test methods is testing to determine the specified mechanical properties of steel, stainless steel and related alloy products for the evaluation of conformance of such products to a material specification under the jurisdiction of ASTM Committee A01 and its subcommittees as designated by a purchaser in a purchase order or contract. 3.1.1x00a0;These test methods may be and are used by other ASTM Committees and other standards writing bodies for the purpose of conformance testing. 3.1.2x00a0;The material condition at the time of testing, sampling frequency, specimen location and orientation, reporting requirements, and other test parameters are contained in the pertinent material specification or in a General Requirement Specification for the particular product form. 3.1.3x00a0;Some material specifications require the use of additional test methods not described herein; in such cases, the required test method is described in that material specification or by reference to another appropriate test method standard. 3.2x00a0;These test methods are also suitable to be used for testing of steel, stainless steel and related alloy materials for other purposes, such as incoming material acceptance testing by the purchaser or evaluation of components after service exposure. 3.2.1x00a0;As with any mechanical testing, deviations from either specification limits or expected as-manufactured properties can occur for valid reasons besides deficiency of the original as-fabricated product. These reasons include, but are not limited to: subsequent service degradation from environmental exposure (for example, temperature, corrosion); static or cyclic service stress effects, mechanically-induced damage, material inhomogeneity, anisotropic structure, natural aging of select alloys, further processing not included in the specification, sampling limitations, and measuring equipment calibration uncertainty. There is statistical variation in all aspects of mechanical testing and variations in test results from prior tests are expected. An understanding of possible reasons for deviation from specified or expected test values should be applied in interpretation of test results. 1.1x00a0;These test methods2 cover procedures and definitions for the mechanical testing of steels, stainless steels, and related alloys. The various mechanical tests herein described are used to determine properties required in the product specifications. Variations in testing methods are to be avoided, and standard methods of testing are to be followed to obtain reproducible and comparable results. In those cases in which the testing requirements for certain products are unique or at variance with these general procedures, the product specification testing requirements shall control. 1.2x00a0;The following mechanical tests are described: x00a0; Sections Tension x00a0;
信息：ICS：77.040.10 (Mechanical testing of metals); 77.140.0 CCS：H22 发布：2013 实施：

ASTM E1824-18 使用热机械分析玻璃化转变温度的标准测试方法:张力法
简介：
信息：ICS：17.200.10 CCS：发布：2018-08-01 实施：

ASTM E2206-11(2015) 热机械分析仪的力校准标准测试方法
简介：
信息：ICS：71.040.50 CCS：发布：2015-10-01 实施：

ASTM F3040/F3040M-2013 非结构性海洋接头舱壁机械静态负载测试的标准试验方法
简介：4.1x00a0;The test method provides information regarding the behavior of a non-structural A, B, or C-Class bulkhead panel system under a static load. Test data for load, moment and deformation is measured. 4.2x00a0;Static load test of non-structural marine joiner panel systems provide a standard method of obtaining data for research and development, quality control, acceptance or rejection under specifications, and special purposes. The tests cannot be considered significant for engineering design in applications differing widely from the loading type and magnitude of the standard test. Such applications shall require additional tests. 1.1x00a0;This test method describes a procedure for evaluating the strength of non structural marine joiner of A, B, and C-Class bulkhead and liner systems. A, B, and C-class bulkheads are defined and discussed in 2.1. 1.2x00a0;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：47.020.10 (Hulls and their structure elements) CCS：发布：2013 实施：

ASTM B877-96(2018) 通过磷钼酸（PMA）方法对金属涂层的总体缺陷和机械损伤的标准测试方法
简介：
信息：ICS：25.220.40 CCS：发布：2018-08-01 实施：

ASTM E2769-15 使用三点弯曲和受控加载速度的热机械分析的弹性模量的标准测试方法
简介：
信息：ICS：29.035.20 CCS：发布：2015-10-01 实施：

ASTM D7750-12 使用封装样品流变仪的动态机械程序的热固性树脂的固化行为的标准测试方法
简介：
信息：ICS：83.080.10 CCS：发布：2012-11-15 实施：

KS B ISO 5006-2018 移动机械 - 操作员的视野 - 测试方法和性能标准
简介：
信息：ICS：53.100 CCS：发布：2018-06-11 实施：

ASTM E1830-15 确定光伏组件机械完整性的标准测试方法
简介：
信息：ICS：27.160 CCS：发布：2015-02-01 实施：

NF C93-471-1-2012 电子设备的机械结构.IEC 60917标准和IEC 60297标准测试.第1部分:环境要求,贮藏柜,行李架,插箱和底盘在室内条件下的试验装备和安全性
简介：
信息：ICS：31.240 CCS：L94 发布：2012-09-01 实施：2012-09-15

ASTM E2769-18 使用三点弯曲和受控加载速度的热机械分析的弹性模量的标准测试方法
简介：
信息：ICS：29.035.20 CCS：发布：2018-06-01 实施：

ASTM D7187-15 通过纳米尺度测量油漆涂层的划痕/ Mar行为的机械方面的标准测试方法
简介：
信息：ICS：87.040 CCS：发布：2015-02-01 实施：

IEC 61587-4-2012 电子设备的机械结构.IEC 60917标准和IEC 60297标准测试.第4部分:组合柜的组装性能水平
简介：
信息：ICS：31.240 CCS：L94 发布：2012-08 实施：

ASTM D4781-03(2018)e1 精细催化剂颗粒和催化剂载体颗粒的机械攻丝包装密度的标准测试方法
简介：
信息：ICS：71.040.30 CCS：发布：2018-05-01 实施：

ASTM C1624-05(2015) 陶瓷涂层的粘附强度和机械破坏模式的标准测试方法通过定量单点划痕测试
简介：
信息：ICS：25.220.99 CCS：发布：2015-01-01 实施：

ASTM D5459-95(2012) 机械方向弹性恢复和拉伸膜的永久变形和应力保持的标准测试方法
简介：
信息：ICS：55.040 CCS：发布：2012-04-01 实施：

ASTM G86-17 测定环境液体氧和加压液体和气态氧环境中材料对机械冲击的点火灵敏度的标准测试方法
简介：
信息：ICS：13.220.40 CCS：发布：2017-12-01 实施：

KS B ISO 15998-2014(2019) 土方机械 - 使用电子元件的机器控制系统（MCS） - 性能标准和功能安全性测试
简介：
信息：ICS：53.100 CCS：发布：2014-12-29 实施：

ASTM A370-2012a 钢制品机械测试的标准试验方法和定义
简介：Significance and UseTop Bottom 3.1 The primary use of these test methods is testing to determine the specified mechanical properties of steel, stainless steel and related alloy products for the evaluation of conformance of such products to a material specification under the jurisdiction of ASTM Committee A01 and its subcommittees as designated by a purchaser in a purchase order or contract. 3.1.1 These test methods may be and are used by other ASTM Committees and other standards writing bodies for the purpose of conformance testing. 3.1.2 The material condition at the time of testing, sampling frequency, specimen location and orientation, reporting requirements, and other test parameters are contained in the pertinent material specification or in a General Requirement Specification for the particular product form. 3.1.3 Some material specifications require the use of additional test methods not described herein; in such cases, the required test method is described in that material specification or by reference to another appropriate test method standard. 3.2 These test methods are also suitable to be used for testing of steel, stainless steel and related alloy materials for other purposes, such as incoming material acceptance testing by the purchaser or evaluation of components after service exposure. 3.2.1 As with any mechanical testing, deviations from either specification limits or expected as-manufactured properties can occur for valid reasons besides deficiency of the original as-fabricated product. These reasons include, but are not limited to: subsequent service degradation from environmental exposure (for example, temperature, corrosion); static or cyclic service stress effects, mechanically-induced damage, material inhomogeneity, anisotropic structure, natural aging of select alloys, further processing not included in the specification, sampling limitations, and measuring equipment calibration uncertainty. There is statistical variation in all aspects of mechanical testing and variations in test results from prior tests are expected. An understanding of possible reasons for deviation from specified or expected test values should be applied in interpretation of test results. 1.1 These test methods2 cover procedures and definitions for the mechanical testing of steels, stainless steels, and related alloys. The various mechanical tests herein described are used to determine properties required in the product specifications. Variations in testing methods are to be avoided, and standard methods of testing are to be followed to obtain reproducible and comparable results. In those cases in which the testing requirements for certain products are unique or at variance with these general procedures, the product specification testing requirements shall control. 1.2 The following mechanical tests are described:
信息：ICS：77.140.01 (Iron and steel products in general) CCS：H22 发布：2012 实施：

ASTM E3098-17 用于形状记忆合金的机械单轴预应变和无热恢复的标准测试方法
简介：
信息：ICS：77.120.99 CCS：发布：2017-11-01 实施：

ASTM F3107-14 计算机辅助外科系统参考框架机械故障后测量精度的标准测试方法
简介：
信息：ICS：35.240.80 CCS：发布：2014-12-01 实施：

ASTM A1058-2012b 钢制品机械测试的标准试验方法(公制)
简介：1.1 These test methods cover mechanical tests described in ASTM, EN,2 ISO,3 and JIS4 standards that utilize the SI system of units. The test methods in each system are not exact equivalents. Each standards system (ASTM, EN, ISO, and JIS) shall be used independently of the other. Combining requirements from any two or more systems may result in nonconformance with the purchase order. 1.2 These test methods cover procedures for the mechanical testing of steels, stainless steels, and related alloys. The various mechanical tests herein described are used to determine properties required in the product specifications. Variations in testing methods are to be avoided, and standard methods of testing are to be followed to obtain reproducible and comparable results. In those cases in which the testing requirements for certain products are unique or at variance with these general procedures, the product specification testing requirements shall control. 1.3 Only one of the testing procedure tracks shall be followed: ASTM, EN, ISO, or JIS. When a test method or practice is not available in one of the tracks then an appropriate test method or practice from an alternative track shall be used. The respective tests are listed in the column shown in Table 1.TABLE 1 Tests and Applicable Standards Test Sections ASTM EN ISO JIS Tension 5 to 12
信息：ICS：77.040.10 (Mechanical testing of metals) CCS：H22 发布：2012 实施：

ASTM D7750-12(2017) 使用封装样品流变仪的动态机械程序的热固性树脂的固化行为的标准测试方法
简介：
信息：ICS：83.080.10 CCS：发布：2017-08-01 实施：

DIN EN ISO 9902-5-2014 纺织机械.噪声测试标准.第5部分:织造和针织用机械(ISO 9902-5-2001+Amd 1-2009+Amd 2-2014),德文版本EN ISO 9902-5-2001+A1-2009+A2-2014
简介：
信息：ICS：17.140.20;59.120.30;59.120.40 CCS：Z32 发布：2014-10-01 实施：

ASTM A1058-2012a 钢制品机械测试的标准试验方法(公制)
简介：1.1 These test methods cover mechanical tests described in ASTM, EN,2 ISO,3 and JIS4 standards that utilize the SI system of units. The test methods in each system are not exact equivalents. Each standards system (ASTM, EN, ISO, and JIS) shall be used independently of the other. Combining requirements from any two or more systems may result in nonconformance with the purchase order. 1.2 These test methods cover procedures for the mechanical testing of steels, stainless steels, and related alloys. The various mechanical tests herein described are used to determine properties required in the product specifications. Variations in testing methods are to be avoided, and standard methods of testing are to be followed to obtain reproducible and comparable results. In those cases in which the testing requirements for certain products are unique or at variance with these general procedures, the product specification testing requirements shall control. 1.3 Only one of the testing procedure tracks shall be followed: ASTM, EN, ISO, or JIS. When a test method or practice is not available in one of the tracks then an appropriate test method or practice from an alternative track shall be used. The respective tests are listed in the column shown in Table 1.TABLE 1 Tests and Applicable Standards Test Sections ASTM EN ISO JIS Tension 5 to 12
信息：ICS：77.040.10 (Mechanical testing of metals) CCS：H22 发布：2012 实施：

ASTM D387-00(2017) 使用机械搅拌机的色素的颜色和强度的标准测试方法
简介：
信息：ICS：87.060.10 CCS：发布：2017-02-01 实施：

DIN EN ISO 9902-2-2014 纺织机械.噪声测试标准.第2部分:纺前预处理机械和纺纱机械 (ISO 9902-2-2001+Amd 1-2009+Amd 2-2014);德文版本EN ISO 9902-2-2001+A1-2009+A2-2014
简介：
信息：ICS：17.140.20;59.120.10 CCS：Z32 发布：2014-10-01 实施：

ASTM A1058-2012 钢制品机械测试的标准试验方法(公制)
简介：1.1 These test methods cover mechanical tests described in ASTM, EN, ISO, and JIS standards that utilize the SI system of units. The test methods in each system are not exact equivalents. Each standards system (ASTM, EN, ISO, and JIS) shall be used independently of the other. Combining requirements from any two or more systems may result in nonconformance with the purchase order. 1.2 These test methods cover procedures for the mechanical testing of steels, stainless steels, and related alloys. The various mechanical tests herein described are used to determine properties required in the product specifications. Variations in testing methods are to be avoided, and standard methods of testing are to be followed to obtain reproducible and comparable results. In those cases in which the testing requirements for certain products are unique or at variance with these general procedures, the product specification testing requirements shall control. 1.3 Only one of the testing procedure tracks shall be followed: ASTM, EN, ISO, or JIS. When a test method or practice is not available in one of the tracks then an appropriate test method or practice from an alternative track shall be used. The respective tests are listed in the column shown in Table 1. Note 18212;The test methods in each system are not exact equivalents. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 Attention is directed to Practice ISO 17025 when there may be a need for information on criteria for evaluation of testing laboratories. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. TABLE 1 Tests and Applicable Standards TestSectionsASTMENISOJIS Tension5 to 12E8/E8M10002-16892Z 2241 Bend13E1907438A7438Z 2248 E290 Bend (tube)13x2026;102328491x2026; Ha......
信息：ICS：77.040.10 (Mechanical testing of metals) CCS：H22 发布：2012 实施：

ASTM D5331-03(2016) 用拉伸膜安装的单元化载荷的机械处理评估的标准测试方法
简介：
信息：ICS：55.220 CCS：发布：2016-12-01 实施：

DIN EN ISO 9902-3-2014 纺织机械.噪声测试标准.第3部分:无纺机械(ISO 9902-3-2001+Amd 1-2009+Amd 2-2014),德文版本EN ISO 9902-3-2001+A1-2009+A2-2014
简介：
信息：ICS：17.140.20;59.120.99 CCS：Z32 发布：2014-10-01 实施：

ASTM A370-2012 钢制品机械测试的标准试验方法和定义
简介：Ductile vs. Brittle Behavior8212;Body-centered-cubic or ferritic alloys exhibit a significant transition in behavior when impact tested over a range of temperatures. At temperatures above transition, impact specimens fracture by a ductile (usually microvoid coalescence) mechanism, absorbing relatively large amounts of energy. At lower temperatures, they fracture in a brittle (usually cleavage) manner absorbing appreciably less energy. Within the transition range, the fracture will generally be a mixture of areas of ductile fracture and brittle fracture. The temperature range of the transition from one type of behavior to the other varies according to the material being tested. This transition behavior may be defined in various ways for specification purposes. The specification may require a minimum test result for absorbed energy, fracture appearance, lateral expansion, or a combination thereof, at a specified test temperature. The specification may require the determination of the transition temperature at which either the absorbed energy or fracture appearance attains a specified level when testing is performed over a range of temperatures. Alternatively the specification may require the determination of the fracture appearance transition temperature (FATTn) as the temperature at which the required minimum percentage of shear fracture (n) is obtained. Further information on the significance of impact testing appears in Annex A5.1.1 These test methods cover procedures and definitions for the mechanical testing of steels, stainless steels, and related alloys. The various mechanical tests herein described are used to determine properties required in the product specifications. Variations in testing methods are to be avoided, and standard methods of testing are to be followed to obtain reproducible and comparable results. In those cases in which the testing requirements for certain products are unique or at variance with these general procedures, the product specification testing requirements shall control. 1.2 The following mechanical tests are described: Sections Tension 5 to 13 Bend14 Hardness15 Brinell16 Rockwell17 Portable18 Impact19 to 28 Keywords29 1.3 Annexes covering details peculiar to certain products are appended to these test methods as follows: Annex Bar ProductsA1.1 Tubular ProductsAnnex A2 FastenersAnnex A3 Round Wire ProductsAnnex A4 Significance of Notched-Bar Impact TestingAnnex A5......
信息：ICS：77.140.01 (Iron and steel products in general) CCS：H22 发布：2012 实施：

ASTM E2425-16 动态机械分析仪的损耗模量一致性的标准测试方法
简介：
信息：ICS：25.040.40 CCS：发布：2016-06-01 实施：

DIN EN ISO 9902-4-2014 纺织机械.噪声测试标准.第4部分:纱线加工,绳索加工机械(ISO 9902-4-2001+Amd 1-2009+Amd 2-2014),德文版本EN ISO 9902-4-2001+A1-2009+A2-2014
简介：
信息：ICS：17.140.20;59.120.99 CCS：Z32 发布：2014-10-01 实施：

ABNT NBR ISO 9533-2011 机械 - 喇叭声音报警和机器上的位移安装 - 测试方法和性能标准
简介：This Standard specifies a static method for determining the sound output performance and alarm activation requirements of audible travel alarms and forward horns mounted on earth-moving machinery, as defi ned in ABNT NBR NM ISO 6165, for operation on work sites and travelling on public roads. It offers objective test methodologies and performance criteria.
信息：ICS：53.100 CCS：发布：2011-12-13 实施：2012-01-13

ASTM B362-91(2016) 温控金属螺旋线圈机械扭矩的标准测试方法
简介：
信息：ICS：29.120.20 CCS：发布：2016-05-01 实施：

DIN EN ISO 9902-6-2014 纺织机械.噪声测试标准.第6部分:织造机械(ISO 9902-6-2001+Amd 1-2009+Amd 2-2014),德文版本EN ISO 9902-6-2001+A1-2009+A2-2014
简介：
信息：ICS：17.140.20;59.120.01 CCS：Z32 发布：2014-10-01 实施：

IEC 61587-1-2011 电子设备的机械结构.IEC 60917标准和IEC 60297标准测试.第1部分:环境要求,贮藏柜,行李架,插箱和底盘在室内条件下的试验装备和安全性
简介：
信息：ICS：31.240 CCS：K05 发布：2011-11 实施：

ASTM E2347-16 通过热机械分析的压痕软化温度的标准测试方法
简介：
信息：ICS：83.080.01 CCS：发布：2016-04-01 实施：