(CMA)
(CNAS)
(ISO)
(高新技术企业)
锡除标准相关标准参考信息
GB 30770-2014修改单 《锡、锑、汞工业污染物排放标准》（GB 30770-2014）修改单
简介：12月21日，生态环境部发布《锡、锑、汞工业污染物排放标准》（GB 30770-2014）修改单，修改单发布之日起环境影响评价文件通过审批的新建、改建和扩建的相关工业企业或生产设施建设项目，自2021年1月1日起实施相关修改单的要求。修改单发布之日前环境影响评价文件已通过审批的相关工业企业或生产设施，自2022年1月1日起实施修改单的要求。
信息：ICS：13.040 CCS：Z60 发布：2020-12-21 实施：2021-01-01
ASTM E310-15 锡青铜铸件标准参考射线照相
简介：
信息：ICS：77.040.20 CCS： 发布：2015-09-01 实施：
ASTM B339-00(2010) 猪锡标准规格
简介：
信息：ICS：77.120.60 CCS： 发布：2010-04-01 实施：
GB 51412-2020 锡冶炼厂工艺设计标准
简介：现批准《锡冶炼厂工艺设计标准》为国家标准，编号为GB51412—2020，自2020年8月1日起实施。其中，第3.0.11、3.0.14、3.0.15、3.0.16、7.1.8、8.0.15、9.2.11（3、4）、12.4.4（1）、12.4.6、12.5.2条（款）为强制性条文，必须严格执行。 本标准在住房和城乡建设部门户网站（www.mohurd.gov.cn）公开，并由住房和城乡建设部标准定额研究所组织中国计划出版社出版发行。 中华人民共和国住房和城乡建设部 2020年1月16日
信息：ICS： CCS： 发布：2020-01-23 实施：
ASTM F3139-15 使用电感耦合等离子体原子发射光谱法分析小型和微量元素的锡基焊料的标准测试方法
简介：
信息：ICS：25.220.40 CCS： 发布：2015-05-01 实施：
ASTM E310-10 锡青铜铸件标准参考射线照相
简介：
信息：ICS：77.040.20 CCS： 发布：2010-01-01 实施：
GB 30770-2014 锡、锑、汞工业污染物排放标准
简介：本标准规定了锡、锑、汞采选及冶炼工业企业水和大气污染物的排放限值、监测和监控要求，以及标准的实施与监督等相关规定。本标准适用于现有锡、锑、汞采选及冶炼工业企业水污染物和大气污染物排放管理，以及锡、锑、汞采选及冶炼工业企业建设项目的环境影响评价、环境保护设计设计、竣工环境保护验收及其投产后的水污染物和大气污染物排放管理。本标准不适用于锡、锑、汞再生及加工等工业。本标准适用于法律允许的污染物排放行为；新设立污染源的选址和特殊保护区域内现有污染源的管理，按照《中华人民共和国大气污染防治法》、《中华人民共和国水污染防治法》、《中华人民共和国海洋环境保护法》、《中华人民共和国固体废物污染环境防治法》、《中华人民共和国放射性污染防治法》、《中华人民共和国环境影响评价法》等法律、法规、规章的相关规定执行。
信息：ICS：13.040 CCS：Z60 发布：2014-05-16 实施：2014-07-01
ASTM F3139-2015 采用感应耦合等离子体发射光谱法分析次要和微量元素锡基焊料合金的标准试验方法
简介：4.1x00a0;Tin-based solder alloys are commonly used to manufacture electrical and electronic goods. The elements lead, cadmium, mercury, antimony and bismuth are often declarable substances in solder materials. This test method provides a means of determining the listed declarable substances, as well as other minor and trace constituents, in tin-based solder alloys. 4.2x00a0;Two methods of dissolving tin-based solder alloys are given in this standard. The first method uses open-vessel hydrofluoric and nitric acid room temperature digestions; the second method employs closed-vessel nitric and hydrofluoric acid microwave digestions, both for use only with ICP-AES instruments equipped with a hydrofluoric acid resistant sample introduction system. 4.3x00a0;The method of preparing calibration solutions uses 1000 mg/kg single element reference material solutions, and uses matching concentrated acids for both the calibration solutions and the sample solutions. 4.4x00a0;This test method is intended for use by laboratories experienced with the set-up, calibration and analysis of samples using ICP-AES. 1.1x00a0;This test method covers procedures for the analysis of tin-based solder alloys for minor and trace elements using inductively-coupled plasma atomic emission spectrometry (ICP-AES) instrumentation. 1.2x00a0;These test procedures were validated for the analytes and mass fractions listed below. Element Validated Mass Fraction Range, mg/kg x00a0; x00a0; Lead 115 to 965 Cadmium 25 to 60 Mercury 5 to 530 Antimony 85 to 1330 Bismuth 80 to 210 Arsenic
信息：ICS： CCS： 发布：2015 实施：
ASTM A623M-2010 一般要求的锡轧制产品的标准规格(公制)
简介：1.1 This specification covers a group of common requirements which, unless otherwise specified in the purchase order or in an individual specification, shall apply to tin mill products. 1.2 In case of conflict in requirements, the requirements of the purchase order, the individual material specification,and this general specification shall prevail in the sequence named. 1.3 The following safety hazards caveat covers Annex A1 through Annex A8 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 18212;A complete inch-pound companion to Specification A623M has been developedA623; therefore, no inch-pound equivalents are presented.
信息：ICS：77.140.50 CCS：H62 发布：2010 实施：
GB 51412-2020 锡冶炼厂工艺设计标准
简介：
信息：ICS： CCS： 发布： 实施：
ASTM E310-2015 锡青铜铸件的标准参考射线照片
简介：4.1x00a0;Reference radiographs for tin bronze and related alloy castings are intended to be used as a guide to the recognition of common discontinuities and their differentiation both as to type and severity level. Discontinuity types most common to these alloys are illustrated. For reference, descriptions of typical casting defects and corresponding radiographic indication types are contained in Section 5. Purchasers and suppliers may, by mutual agreement, select particular discontinuity categories (see 1.2) to serve as standards representing minimum levels of acceptability (see Sections 7 and 8). 4.2x00a0;Reference radiographs represented by this standard may be used, as agreed upon in a purchaser supplier agreement, for energy levels, thicknesses or both outside the range of this standard when determined applicable for the casting service application. Section 10 addresses purchaser supplier requisites where weld repairs may be required. 4.3x00a0;Procedures for evaluation of production radiographs using applicable reference radiographs of this standard are prescribed in Section 9; however, there may be manufacturing-purchaser issues involving specific casting service applications where it may be appropriate to modify or alter such requirements. Where such modifications may be appropriate for the casting application, all such changes shall be called-out in the purchaser supplier agreement or contractual document. 4.4x00a0;The following ASTM specifications illustrate alloys covered by these standards; however, it is intended that these reference radiographs also apply to related government and commercial material specifications: Valve bronze castings B61A Composition bronze or ounce metal castings B62B Tin bronze sand castings B584 Leaded red brass sand castings B584
信息：ICS：77.040.20;77.150.60 CCS： 发布：2015 实施：
ASTM A623-2010 一般要求的锡轧制产品的标准规格
简介：tin mill products; Abbreviated ratio tables; Aerated media polarization (AMP) test; Alloy-tin couple (ATC) test; Chromium coatings--specifications; Diphenylcarbazide method; Dissolution rate; Iron solution value; Metallic coatings--specifications; Pickle lag test; Tin crystal size test; Tin mill products--specifications; Total surface oil1.1 This specification covers a group of common requirements which, unless otherwise specified in the purchase order or in an individual specification, shall apply to tin mill products. 1.2 In case of any conflict in requirements, the requirements of the purchase order, the individual material specification, and this general specification shall prevail in the sequence named. Note 18212;A complete metric companion to Specification A623 has been developedSpecification A623M; therefore no metric equivalents are presented in this specification. 1.3 The following safety caveat covers Annex A3 through Annex A10 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：77.140.50 CCS：H62 发布：2010 实施：
ASTM E3185-21 锡青铜铸件的标准数字参考图像
简介：
信息：ICS： CCS： 发布：2021-12-15 实施：
ASTM A630-03(2014) 电解锡板的镀锡重量测定标准试验方法
简介：
信息：ICS：25.220.40 CCS： 发布：2014-10-01 实施：
ASTM B967/B967M-2010a 铜锌锡铋合金条材,棒材和线材的标准规格
简介：1.1 This specification establishes the requirements for copper-zinc-tin-bismuth alloy rod, bar and wire of alloy UNS Nos. C49260, C49300, C49340, and C49350 intended for use in plumbing applications and drinking water systems. 1.2 Typically, rod and bar product made to this specification is furnished as straight lengths. Wire (H04) 0.08-0.3 in. [2-8 mm inclusive] is furnished in coil form, and H50 shapes. 1.3 Units8212;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 The following safety hazard caveat pertains only to the test method(s) described in this specification. 1.4.1 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：77.150.30 CCS：H62 发布：2010 实施：
ASTM B844-98(2021) 银锡氧化物接触材料的标准指南
简介：
信息：ICS：77.120.99 CCS： 发布：2021-11-01 实施：
ASTM A987/A987M-09(2014) 测量锡磨产品形状特征的标准实践
简介：
信息：ICS：77.140.50 CCS： 发布：2014-10-01 实施：
ASTM E310-2010 锡青铜铸件的标准参考底片
简介：Reference radiographs for tin bronze and related alloy castings are intended to be used as a guide to the recognition of common discontinuities and their differentiation both as to type and severity level. Discontinuity types most common to these alloys are illustrated. For reference, descriptions of typical casting defects and corresponding radiographic indication types are contained in Section 5. Purchasers and suppliers may, by mutual agreement, select particular discontinuity categories (see 1.2) to serve as standards representing minimum levels of acceptability (see Sections 7 and 8). Reference radiographs represented by this standard may be used, as agreed upon in a purchaser supplier agreement, for energy levels, thicknesses or both outside the range of this standard when determined applicable for the casting service application. Section 10 addresses purchaser supplier requisites where weld repairs may be required. Procedures for evaluation of production radiographs using applicable reference radiographs of this standard are prescribed in Section 9; however, there may be manufacturing-purchaser issues involving specific casting service applications where it may be appropriate to modify or alter such requirements. Where such modifications may be appropriate for the casting application, all such changes shall be called-out in the purchaser supplier agreement or contractual document. The following ASTM specifications illustrate alloys covered by these standards; however, it is intended that these reference radiographs also apply to related government and commercial material specifications:
信息：ICS：77.150.60 (Lead, zinc and tin products) CCS：H62 发布：2010 实施：
T/ZJGFTR 002-2021 再生退锡液产品标准
简介：将蚀刻退锡废液进行负压浓缩，馏出物经过三级吸收后回收稀硝酸，稀硝酸与适量的外购65%硝酸混合，配成一定当量的硝酸溶液，并加入少量硝酸铁或硝酸铁溶液、添加剂等，搅拌混合均匀配成再生退锡液。
信息：ICS：13.030.50 CCS：N772 发布：2021-08-25 实施：2021-09-07
ASTM B275-2014 某些锌, 锡以及铅压铸件编纂的标准实施规程
简介：1.1x00a0;This practice covers a system for designating die casting alloys of zinc, tin and lead. Those designations currently being used in specifications under the jurisdiction of Committees B02 on Nonferrous Metals are listed in 8201;Table X2.1 in Appendix X2. Note 1:x00a0;The alloy designations now being used in Committee B07 specifications for aluminum and aluminum-alloy wrought and cast products conform to ANSI H35.1. Alloys formerly codified by this practice and the corresponding ANSI designations are shown in Tables X3.1 and X3.2 of Appendix X3 for legacy purposes. Note 2:x00a0;The alloy designations now being used in Committee B07 specifications for magnesium and magnesium-alloy wrought and cast products conform to Practice B951, as indicated in Appendix X4. Alloy designations formerly codified by this practice are no longer relevant. 1.2x00a0;The equivalent Unified Numbering System (UNS) alloy designations shown in the appendixes are in accordance with Practice E527.
信息：ICS：77.150.01 CCS： 发布：2014 实施：
ASTM B422/B422M-2010e1 铜-铝-硅-钴合金,铜-镍-硅-镁合金,铜-镍-硅合金,铜-镍-铝-镁合金,和铜-镍-锡合金片材和带材标准规格
简介：1.1x00a0;This specification establishes the requirements for2 Copper Alloy UNS Nos. C19002, C19010, C19015, ,C19020, C19025, C63800, C64725, C70250, C70260, C70265, and C70310 sheet and strip. 1.2x00a0;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：77.150.30 (Copper products) CCS：H62 发布：2010 实施：
ASTM E310-21 锡青铜铸件的标准参考射线照片
简介：
信息：ICS：77.040.20 CCS： 发布：2021-07-01 实施：
ASTM B907-2013 用作焊料的锌、锡和镉基合金的标准规格
简介：1.1x00a0;This specification covers solder metal alloys (commonly known as soft solders), including zinc-aluminum, zinc-aluminum-copper, zinc-tin, zinc-tin-copper, zinc-cadmium-tin, zinc-cadmium, tin-zinc, cadmium-zinc, cadmium-zinc-silver, and cadmium-silver, used as solders for the purpose of joining together two or more metals at temperatures below their melting points. 1.1.1x00a0;Certain alloys specified in this standard are also used as Thermal Spray Wire in the electronics industry and are covered for this purpose in Specification B943. Specification B833 covers Zinc and Zinc Alloy Wire for Thermal Spraying (Metallizing) used primarily for the corrosion protection of steel (as noted in Annex A1 of this specification). 1.1.2x00a0;Tin base alloys are included in this specification because their use in the electronics industry is different than the major use of the tin and lead solder compositions specified in Specification B32. 1.1.3x00a0;These solders include alloys having a nominal liquidus temperature not exceeding 850x00b0;F (455x00b0;C). 1.1.4x00a0;This specification includes solder in the form of solid bars, ingots, wire, powder and special forms, and in the form of solder paste. 1.2x00a0;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3x00a0;Toxicityx2014;Warning: Soluble and respirable forms of cadmium may be harmful to human health and the environment in certain forms and concentrations. Therefore, ingestion and inhalation of cadmium should be controlled under the appropriate regulations of the U.S. Occupational Safety and Health Administration (OSHA). Cadmium-containing alloys and coatings should not be used on articles that will contact food or beverages, or for dental and other equipment that is normally inserted in the mouth. Similarly, if articles using cadmium-containing alloys or coatings are welded, soldered, brazed, ground, flame-cut, or otherwise heated during fabrication, adequate ventilation must be provided to maintain occupational cadmium exposure below the OSHA Permissible Exposure Level (PEL). 1.4x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.
信息：ICS：77.120.60 (Lead, zinc, tin and their alloys) CCS：J33 发布：2013 实施：
ASTM A987/A987M-09 测量锡磨产品形状特征的标准实践
简介：
信息：ICS：77.140.50 CCS： 发布：2009-05-01 实施：
ASTM E310-15(2019)e1 锡青铜铸件标准参考射线照相
简介：
信息：ICS：77.040.20 CCS： 发布：2019-12-01 实施：
ASTM B545-2013 锡电解沉积层标准规格
简介：1.1x00a0;This specification covers the requirements for electrodeposited (electroplated) coatings of tin applied to metallic articles. Tin coatings are used to provide a low contact-resistance surface, to protect against corrosion (see 1.2), to facilitate soldering, to provide anti-galling properties, and to be a stopoff coating in the nitriding of high-strength steels. 1.2x00a0;Some corrosion can be expected from tin coatings exposed outdoors. In normal indoor exposure, tin is protective on iron, steel, nickel, copper, and their alloys. Corrosion can be expected at discontinuities in the coating (such as pores) due to galvanic couples formed between the tin and the underlying metal through the discontinuities, especially in humid atmospheres. Porosity increases as the coating thickness decreases, so that minimum thicknesses must be specified for each application. Parts coated with tin can be assembled safely in contact with iron and steel, tin-coated aluminum, yellow chromated zinc, cadmium, and solder coatings. (See X5.1 for oxidation and corrosion properties.) 1.3x00a0;This specification applies to electroplated coatings of not less than 998201;% tin (except where deliberately alloyed for special purposes, as stated in X6.3) obtained from any of the available tin electroplating processes (see 4.3). 1.4x00a0;This specification does not apply to hot-dipped tin or other non-electrodeposited coating; it also does not apply to mill products. For mill products, refer to Specifications A623 or A623M. 1.5x00a0;The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.6x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：25.220.40 (Metallic coatings) CCS：A29 发布：2013 实施：
ASTM A630-03(2009) 电解锡板的镀锡重量测定标准试验方法
简介：
信息：ICS：25.220.40 CCS： 发布：2009-04-01 实施：
ASTM A987/A987M-19 测量锡磨产品形状特征的标准实践
简介：
信息：ICS：77.140.50 CCS： 发布：2019-11-01 实施：
ASTM B339-12 猪锡标准规格
简介：
信息：ICS：77.120.60 CCS： 发布：2012-05-01 实施：
ANSI/UL 10Aa-2009 锡包防火门标准
简介：
信息：ICS：91.060.50 CCS：Q70 发布：2009 实施：
ASTM B339-19 猪锡标准规格
简介：
信息：ICS：77.120.60 CCS： 发布：2019-11-01 实施：
ASTM B967/B967M-2012 铜-锌-锡-铋合金条材,棒材及线材标准规格
简介：1.1 This specification establishes the requirements for copper-zinc-tin-bismuth alloy rod, bar and wire of alloy UNS Nos. C49255, C49260, C49300, C49340, C49350, C49355, and C49360 intended for use in plumbing applications and drinking water systems. 1.2 Typically, rod and bar product made to this specification is furnished as straight lengths. Wire (H04) 0.08-0.3 in. [2-8 mm inclusive] is furnished in coil form, and H50 shapes. 1.3 Units8212;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 The following safety hazard caveat pertains only to the test method(s) described in this specification. 1.4.1 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：77.150.30 (Copper products) CCS：H62 发布：2012 实施：
ANSI/UL 14Ba-2008 标准水平安装锡复合防火门用滑动五金器具标准
简介：
信息：ICS：91.060.50 CCS：Y73 发布：2008-01-01 实施：
ASTM B929-17 铜镍锡尖晶合金棒棒标准规格
简介：
信息：ICS：77.150.30 CCS： 发布：2017-05-15 实施：
ASTM B967/B967M-2012a 铜-锌-锡-铋合金条材、棒材及线材的标准规格
简介：1.1 This specification establishes the requirements for copper-zinc-tin-bismuth alloy rod, bar and wire of alloy UNS Nos. C49250, C49255, C49260, C49300, C49340, C49350, C49355, and C49360 intended for use in plumbing applications and drinking water systems. 1.2 Typically, rod and bar product made to this specification is furnished as straight lengths. Wire (H04) 0.08-0.3 in. [2-8 mm inclusive] is furnished in coil form, and H50 shapes. 1.3 Units???The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 The following safety hazard caveat pertains only to the test method(s) described in this specification. 1.4.1 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：77.150.30 (Copper products) CCS：H62 发布：2012 实施：
ANSI/UL 14C-2008 标准单扇和双扇包锡标准防火门用旋转五金件标准
简介：These requirements apply to hardware for swinging fire doors which have demonstrated in fire tests fire-resistive properties warranting their use with two-ply and three-ply tin-clad fire doors tested in accordance with the Standard for Fire Tests of Door Assemblies, UL 10B (ASTM E152, NFPA No. 252).
信息：ICS：91.060.50 CCS：J10 发布：2008 实施：
ASTM B422/B422M-2017 铜铝硅钴合金, 铜镍硅镁合金, 铜镍硅合金, 铜镍铝镁合金和铜镍锡合金薄板和带材的标准规格
简介：1.1x00a0;This specification establishes the requirements for2 Copper Alloy UNS Nos. C19002, C19010, C19015, C19020, C19025, C63800, C64725, C70250, C70260, C70265, C70310, and C70350 sheet and strip. 1.2x00a0;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3x00a0;The following safety hazard caveat pertains only to the test method(s) described in this specification. 1.3.1x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.4x00a0;This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
信息：ICS：77.150.30 CCS：H62 发布：2017 实施：
ANSI/GEIA STD-0005-2-A-2012 降低航空航天和高性能电子系统中锡晶须影响的标准
简介：
信息：ICS：31.020;49.060 CCS：V25 发布：2012 实施：
ANSI/UL 14B-2008 标准水平安装的包锡防火门的平滑金属器具用标准
简介：These requirements apply to hardware for horizontally sliding fire doors which have demonstrated in fire tests fire-resistive properties warranting their use with two-ply and three-ply tin-clad fire doors tested in accordance with the Standard for Fire Tests of Door Assemblies, UL 10B (ASTM E152, NFPA No. 252).
信息：ICS：91.060.50 CCS：Q70 发布：2008 实施：
ASTM A630-16a 电解锡板的镀锡重量测定标准试验方法
简介：
信息：ICS：25.220.40 CCS： 发布：2016-12-01 实施：
ASTM B122/B122M-2011 铜镍锡合金,铜镍锌合金(镍银),铜镍合金中厚板,薄板,条板及轧制棒材的标准规格
简介：1.1 This specification establishes the requirements for copper-nickel-tin alloy, copper-nickel-zinc alloy (nickel silver), and copper-nickel alloy plate, sheet, strip, and rolled bar. The following alloys are covered: Previously Copper AlloyUsed Nominal Composition, UNS No. Designation% Copper Nickel Zinc TinChro- mium C70600...9010 ......... C70620...8610......... C7100068020 ......... C7150057030 ......... C71520...6531......... C72200...8515 ......0.5 C72500...89 9 ...2... C7350017218 10...... C7400097010 20............
信息：ICS：77.150.30 (Copper products) CCS：H62 发布：2011 实施：
ASTM A987-07 测量锡磨产品形状特征的标准实践
简介：
信息：ICS：77.140.50 CCS： 发布：2007-11-01 实施：
ASTM A630-16ae1 电解锡板的镀锡重量测定标准试验方法
简介：
信息：ICS：25.220.40 CCS： 发布：2016-12-01 实施：
ASTM B967/B967M-2011a 铜锌锡铋合金条材,棒材及线材标准规格
简介：1.1 This specification establishes the requirements for copper-zinc-tin-bismuth alloy rod, bar and wire of alloy UNS Nos. C49255, C49260, C49300, C49340, C49350, and C49360 intended for use in plumbing applications and drinking water systems. 1.2 Typically, rod and bar product made to this specification is furnished as straight lengths. Wire (H04) 0.08-0.3 in. [2-8 mm inclusive] is furnished in coil form, and H50 shapes. 1.3 Units8212;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 The following safety hazard caveat pertains only to the test method(s) described in this specification. 1.4.1 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：77.150.30 (Copper products) CCS：H62 发布：2011 实施：
ASTM A599/A599M-2007(2017) 锡制品, 冷轧电解镀锡薄板的标准规格
简介：1.1x00a0;This specification covers cold-rolled steel sheet in coils or in cut lengths, tin-coated by electrodeposition. The product is commonly known as electrolytic tin-coated sheet, and is for applications that need good solderability, good surface appearance, and a degree of corrosion resistance. Tin-coated sheet is produced to various designations of tin coating, as outlined in Table 1. TABLE 1 Electrolytic Tin-Coated Sheets Coating Weight [Mass] Note 1:x00a0;Listed below are the commonly produced coating weights [mass] upon agreement between the producer and the purchaser. Other combinations of coatings may be specified and the appropriate minimum average test valuesA apply. Designation No. Nominal Tin Coating Weight [Mass] (Each Surface) lb/base box (g/m2)B Minimum Average Coating Weight [Mass] (Each Surface Test Value) lb/base box (g/m2)B, C 5 (0.6/0.6) 0.025/0.025 (0.6/0.6) 0.02/0.02 (0.5/0.5) 10 (1.1/1.1)8199; 0.05/0.05 (1.1/1.1) 0.04/0.04 (0.9/0.9) 15 (1.7/1.7)8199; 0.075/0.075 (1.7/1.7) 0.06/0.06 (1.4/1.4) 20 (2.2/2.2)8199; 0.10/0.10 (2.2/2.2) 0.08/0.08 (1.8/1.8) 25 (
信息：ICS：77.140.50 CCS：H46 发布：2007 实施：
ASTM A630-16 电解锡板的镀锡重量测定标准试验方法
简介：
信息：ICS：25.220.40 CCS： 发布：2016-05-01 实施：
ASTM A1074-2011(2015) 黑色和有色金属上热锡和热锡/铅浸的标准规格
简介：1.1x00a0;This specification covers tin and tin/lead coatings applied by the hot dip process on ferrous and non-ferrous metals. hot tin and tin/lead coatings are used to provide a low contact-resistance surface, to protect against corrosion, to facilitate soldering, to provide anti-galling properties, and to be a stop-off coating in the nitriding of high-strength steels. 1.2x00a0;This specification is intended to be applicable to items that are reflowed, centrifuged or otherwise handled to remove excess tin or tin/lead bath metal. Coating thickness grade requirements reflect this. 1.3x00a0;Some corrosion can be expected from tin or tin/lead coatings exposed outdoors. In normal indoor exposure, tin or tin/lead is protective on iron, steel, nickel, copper, and their alloys. Corrosion can be expected at discontinuities in the coating (such as pores) due to galvanic couples formed between the tin or the tin/lead and the underlying metal through the discontinuities, especially in humid atmospheres. 1.4x00a0;This specification applies to hot tin dip coatings of not less than 99.88201;% tin and to hot tin/lead dip coatings of 60 x00b1; 58201;% tin and the balance lead. 1.5x00a0;This specification does not apply to electrodeposited coatings of tin or tin/lead. 1.6x00a0;The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.7x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS： CCS： 发布：2011 实施：
ASTM A987-2007 锡轧制产品的形状特性测量的标准实施规程
简介：4.1 The definitions and procedures for measuring shape characteristics of tin mill products are provided so that purchasers and suppliers have common measuring procedures and definitions of shape characteristics. These procedures provide definitions and measuring techniques of shape characteristics. The intention of these definitions and measuring practices is not to provide a dimensional specification for shape characteristics, but rather common procedure(s) for quantifying shape anomalies.1.1 Shape is a significant quality characteristic for tin mill products. Plate-shape is affected by mill process factors plus the temper, thickness and width of the material supplied. It is the purpose of this practice to define accurately the different plate shape characteristics and to describe the practice(s) most commonly used to measure particular characteristics.1.2 Quantitative limits are not addressed and should be established on an individual producer and user basis, where appropriate.1.3 This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.
信息：ICS：77.140.50 (Flat steel products and semi-products) CCS：H62 发布：2007 实施：
ASTM B844-98(2016) 氧化锡锡触点材料标准指南
简介：
信息：ICS：77.120.99 CCS： 发布：2016-05-01 实施：
ASTM A1074-2011 黑色金属和有色金属上热镀锡和热浸锡/铅的标准规格
简介：1.1 This specification covers tin and tin/lead coatings applied by the hot dip process on ferrous and non-ferrous metals. hot tin and tin/lead coatings are used to provide a low contact-resistance surface, to protect against corrosion, to facilitate soldering, to provide anti-galling properties, and to be a stop-off coating in the nitriding of high-strength steels. 1.2 This specification is intended to be applicable to items that are reflowed, centrifuged or otherwise handled to remove excess tin or tin/lead bath metal. Coating thickness grade requirements reflect this. 1.3 Some corrosion can be expected from tin or tin/lead coatings exposed outdoors. In normal indoor exposure, tin or tin/lead is protective on iron, steel, nickel, copper, and their alloys. Corrosion can be expected at discontinuities in the coating (such as pores) due to galvanic couples formed between the tin or the tin/lead and the underlying metal through the discontinuities, especially in humid atmospheres. 1.4 This specification applies to hot tin dip coatings of not less than 99.8 % tin and to hot tin/lead dip coatings of 60 x00B1; 5 % tin and the balance lead. 1.5 This specification does not apply to electrodeposited coatings of tin or tin/lead. 1.6 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS： CCS：H62 发布：2011 实施：
ASTM A599/A599M-2007(2012) 锡制品、电解镀锡的冷轧薄板标准规格
简介：1.1 This specification covers cold-rolled steel sheet in coils or in cut lengths, tin-coated by electrodeposition. The product is commonly known as electrolytic tin-coated sheet, and is for applications that need good solderability, good surface appearance, and a degree of corrosion resistance. Tin-coated sheet is produced to various designations of tin coating, as outlined in Table 1. TABLE 1 Electrolytic Tin-Coated Sheets Coating Weight [Mass]Note 1???Listed below are the commonly produced coating weights [mass] upon agreement between the producer and the purchaser. Other combinations of coatings may be specified and the appropriate minimum average test valuesA apply. Designation No. Nominal Tin Coating Weight [Mass] (Each Surface) lb/base box (g/m2)B Minimum Average Coating Weight [Mass] (Each Surface Test Value) lb/base box (g/m2)B, C 5 (0.6/0.6) 0.025/0.025 (0.6/0.6) 0.02/0.02 (0.5/0.5) 10 (1.1/1.1)8199; 0.05/0.05 (1.1/1.1) 0.04/0.04 (0.9/0.9) 15 (1.7/1.7)8199; 0.075/0.075 (1.7/1.7) 0.06/0.06 (1.4/1.4) 20 (2.2/2.2)8199; 0.10/0.10 (2.2/2.2) 0.08/0.08 (1.8/1.8) 25 (2.8/2.8)8199; 0.125/0.125 (2.8/2.8) 0.11/0.11 (2.5/2.5)
信息：ICS：77.140.50 (Flat steel products and semi-products) CCS：H62 发布：2007 实施：
ASTM A623-2016 锡磨机产品通用要求的标准规格
简介：1.1x00a0;This specification covers a group of common requirements, which unless otherwise specified in the purchase order or in an individual specification, shall apply to tin mill products. 1.2x00a0;In case of any conflict in requirements, the requirements of the purchase order, the individual material specification, and this general specification shall prevail in the sequence named. Note 1:x00a0;A complete metric companion to Specification A623 has been developedx2014;Specification A623M; therefore no metric equivalents are presented in this specification. 1.3x00a0;The following safety caveat covers Annex A3 through Annex A10 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：77.140.50 CCS：H46 发布：2016 实施：
ASTM A623-2011 锡轧制产品的标准规格.一般要求
简介：1.1 This specification covers a group of common requirements, which unless otherwise specified in the purchase order or in an individual specification, shall apply to tin mill products. 1.2 In case of any conflict in requirements, the requirements of the purchase order, the individual material specification, and this general specification shall prevail in the sequence named. Note 18212;A complete metric companion to Specification A623 has been developedSpecification A623M; therefore no metric equivalents are presented in this specification. 1.3 The following safety caveat covers Annex A3 through Annex A10 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：77.140.50 (Flat steel products and semi-products) CCS：J31 发布：2011 实施：
UL 10A BULLETIN-2007 锡包防火门UL安全性标准.评议提交截止日期:2007年10月31日
简介：Covers the design and construction details of tin-clad fire doors that, when so fabricated, have demonstrated fire performance properties sufficient to warrant their use as fire doors having a rating of 3, 1-1/2, or 3/4 hour, based on wire tests conducted in accordance with the American National Standard for Fire Tests of Door Assemblies, ANSI/UL 10B.
信息：ICS：91.060.50 CCS：Q70 发布：2007 实施：
ASTM B122/B122M-2016 铜镍锡合金, 铜镍锌合金 (镍银)和铜镍合金板材, 薄板, 带材和轧制棒材的标准规格
简介：1.1x00a0;This specification establishes the requirements for copper-nickel-tin alloy, copper-nickel-zinc alloy (nickel silver), and copper-nickel alloy plate, sheet, strip, and rolled bar. The following alloys are covered: x00a0; x00a0; Nominal Composition, % Copper Alloy Previously Used x00a0; x00a0; x00a0; x00a0; Chro- UNS No.2 Designation Copper Nickel Zinc Tin mium x00a0; C70600 ... 90 10 ... ... ... C70620 .........
信息：ICS：77.150.30 CCS： 发布：2016 实施：
ASTM B967/B967M-2011 铜锌锡铋合金条材,棒材和线材标准规格
简介：1.1 This specification establishes the requirements for copper-zinc-tin-bismuth alloy rod, bar and wire of alloy UNS Nos. C49255, C49260, C49300, C49340, C49350, and C49360 intended for use in plumbing applications and drinking water systems. 1.2 Typically, rod and bar product made to this specification is furnished as straight lengths. Wire (H04) 0.08-0.3 in. [2-8 mm inclusive] is furnished in coil form, and H50 shapes. 1.3 Units8212;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 The following safety hazard caveat pertains only to the test method(s) described in this specification. 1.4.1 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：77.150.30 CCS：H62 发布：2011 实施：
GEIA-STD-0005-2-2006 航天和高性能电子系统锡晶影响减轻标准
简介：Due to a variety of real and potential health issues, many constituent materials used in theproduction of electronic products have come under scrutiny.
信息：ICS：49.060 CCS：L94 发布：2006-06-01 实施：
ASTM A623M-2016 锡磨机产品通用要求的标准规格(米制)
简介：1.1x00a0;This specification covers a group of common requirements, which unless otherwise specified in the purchase order or in an individual specification, shall apply to tin mill products. 1.2x00a0;In case of conflict in requirements, the requirements of the purchase order, the individual material specification, and this general specification shall prevail in the sequence named. 1.3x00a0;The following safety hazards caveat covers Annex A1 through Annex A8 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 1:x00a0;A complete inch-pound companion to Specification A623M has been developedx2014;A623; therefore, no inch-pound equivalents are presented.
信息：ICS：77.140.50 CCS：H46 发布：2016 实施：
ASTM B844-98(2010) 氧化锡锡触点材料标准指南
简介：
信息：ICS：77.120.99 CCS： 发布：2010-10-01 实施：
UL 14C-2006 标准单扇和双扇包锡防火门用旋转五金件
简介：These requirements apply to hardware for swinging fire doors which have demonstrated in fire tests fire-resistive properties warranting their use with two-ply and three-ply tin-clad fire doors tested in accordance with the Standard for Fire Tests of Door Assemblies, UL 10B (ASTM E152, NFPA No. 252). Requirements for the location and time rating required for fire doors are contained in codes such as the BOCA National Building Code, Standard Building Code (for SBCCI), and Uniform Building Code (for ICBO). Requirements for the installation of swinging two-ply and three-ply tin-clad fire doors are included in the Standard for Fire Doors and Fire Windows, NFPA No. 80. The hardware included in these requirements is intended for mounting standard two-ply and three-ply tin-clad swinging fire doors for protection of openings not exceeding the dimensions for the hourly classifications indicated in Table 1.1."Limitations in types and dimensions". These requirements do not cover automatic releasing or closing mechanisms.
信息：ICS：91.060.50 CCS：Y71 发布：2006 实施：
我们的实力
部分实验仪器
合作客户
注意：因业务调整，暂不接受个人委托测试望见谅。
