试验炉检测标准试验炉-中析研究所检测

(CMA)

(CNAS)

(ISO)

(高新技术企业)

试验炉相关标准参考信息

GB/T 10066.2-2019 电热和电磁处理装置的试验方法第2部分：直接电弧炉
简介：
信息：ICS：25.180.10 CCS：K61 发布：2019-08-30 00:00:00.0 实施：2020-03-01 00:00:00.0

HG/T 5451～5453-2018 不透性石墨防爆膜水压爆破试验方法、圆块孔式不透性石墨降膜吸收器和二合一石墨氯化氢合成炉（2018）
简介：
信息：ICS： CCS：G94 发布：2018-10-22 实施：2019-04-01

ASTM F2894-14 用热空气循环炉评定耐热材料、防护服和设备的标准试验方法
简介：
信息：ICS：13.340.01 CCS：发布：2014-02-01 实施：

GB/T 10066.10-2005 电热装置的试验方法第10部分;直接电弧炉
简介：GB/T 10066的本部分规定了测定三相直流电弧炉主要参数和技术运行特性的试验条件和方法。本部分适用于额定容量等于或大于500 kg的三相直接电弧炉，包括三相交流电弧炉、钢包精炼炉、直流电弧炉等。这些炉子适合于在常压或接近常压情况下熔炼固态炉料和精炼液态炉料。本部分也适应于有别于三相炉的具有一个或多个电极的电弧炉。熔化黑色金属（例如钢、铁盒有色金属（例如铜）的电弧炉也可作为保温炉使用，用于液态炉料出炉前的过热和保温。本部分的目的是测定电弧炉主要参数和技术运行特性的试验条件和方法标准化。注1：进行这些试验与补偿设备无关。本部分没有包含为电弧炉技术和经济评价可能进行的全部试验方法。注2：补充试验条件由制造商和用户协商。用于直流电弧的某些专用设备的试验，如可控整流器的试验，见GB/T 3859.1-1993 。
信息：ICS：25.180.10 CCS：K60 发布：2005-08-26 实施：2006-04-01

ASTM D4239-2018e1 用高温管式炉燃烧法测定煤和焦炭分析样品中硫含量的标准试验方法
简介：4.1x00a0;Sulfur is part of the ultimate analysis of coal and coke. 4.2x00a0;Results of the sulfur analysis are used for evaluation of coal preparation and cleaning, evaluation of potential sulfur emissions from coal and coke combustion or conversion processes, and evaluation of coal and coke quality in relation to contract specifications, as well as for scientific purposes. 4.3x00a0;The competency of laboratories with respect to use of this standard can be established through reference to Practice D7448. 1.1x00a0;This test method covers the determination of sulfur in samples of coal or coke by high-temperature tube furnace combustion. 1.1.1x00a0;Two analysis methods are described. 1.2x00a0;When automated equipment is used, either method can be classified as an instrumental method. 1.3x00a0;The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.4x00a0;All percentages are percent mass fractions unless otherwise noted. 1.5x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6x00a0;This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
信息：ICS：75.160.10 CCS：发布：2018 实施：

ASTM F2861-2014 联炉在不同模式下增强性能的标准试验方法
简介：5.1x00a0;The energy input rate test and thermostat calibration are used to confirm that the combination oven is operating properly prior to further testing and to ensure that all test results are determined at the same temperature. 5.2x00a0;Preheat energy and time can be useful to food service operators to manage power demands and to know how quickly the combination oven can be ready for operation. 5.3x00a0;Idle energy rate and pilot energy rate can be used to estimate energy consumption during non-cooking periods. 5.4x00a0;Cooking-energy efficiency is a precise indicator of combination oven energy performance under various operating conditions. This information enables the food service operator to consider energy performance when selecting a combination oven. 5.5x00a0;Production capacity can be used by food service operators to choose a combination oven that matches their food output requirements. 5.6x00a0;Water consumption characterization is useful for estimating water and sewage costs associated with combination oven operation. 5.7x00a0;Condensate temperature measurement is useful to verify that the condensate temperature does not violate applicable building codes. 5.8x00a0;Cooking uniformity provides information regarding the combination ovenx2019;s ability to cook food at the same rate throughout the oven compartment. 1.1x00a0;This test method covers the evaluation of the energy and water consumption and the cooking performance of combination ovens that can be operated in hot air convection, steam, and the combination of both hot air convection and steam modes. The test method is also applicable to convection ovens with moisture injection. The results of this test method can be used to evaluate a combination oven and understand its energy consumption. 1.2x00a0;This test method is applicable to gas and electric combination ovens that can be operated in convection, steam and combination modes. 1.3x00a0;The combination oven can be evaluated with respect to the following (where applicable): 1.3.1x00a0;Energy input rate and thermostat calibration (10.2). 1.3.2x00a0;Preheat energy consumption and time (10.3). 1.3.3x00a0;Idle energy rate in convection, steam and combination modes (10.4). 1.3.4x00a0;Pilot energy rate (if applicable) (10.5). 1.3.5x00a0;Cooking-energy efficiency, cooking energy rate, production capacity, water consumption and condensate temperature in steam mode (10.6). 1.3.6x00a0;Cooking-energy efficiency, cooking energy rate, and production capacity in convection mode (10.7). 1.3.7x00a0;Cooking uniformity in combination mode (10.8). 1.4x00a0;The values stated in inch-pound uni......
信息：ICS：97.040.20 (Cooking ranges, working tables, ovens a CCS：发布：2014 实施：

GB/T 10066.11-2005 电热装置的试验方法第11部分;埋弧炉
简介：本部分适用于工业用埋弧炉，例如用来生产硅铁的埋弧炉。本部分中有关电参数的条款是按三相，每相只有一根电极的埋弧炉制定的。当本部分用于单相埋弧炉或每相有多根电极的三相埋弧炉时，这些条款应作相应修改。注：所有电器试验都要排除无功功率补偿和（或）电压稳定装置的影。如果在试验期间不能断开这些装置，则本部分中有关主电路的各条仍然适用，只是应指出无功功率补偿装置和（或）电压稳定装置也同时投人工作，并需补充说明适用的供电网和这这类装置的影响。本部分的目的是使测量埋弧炉的基本参数和技术特征的试验方法标准化。本部分给出的试验项目不适强制性和约束性的。本部分没有包含对埋弧炉进行技术和经济评价时可作的所有试验的试验方法。对埋弧炉技术经济评价所需进行的试验项目中选取和增补，必要时在产品标准中补充规定或由制造商和用户协商。
信息：ICS：25.180.10 CCS：K60 发布：2005-08-26 实施：2006-04-01

NF E51-729-3-2017 建筑物通风.住宅通风用组件/产品的性能试验.第3部分:无风扇的住宅用炉罩
简介：
信息：ICS：91.140.30;97.040.20 CCS：J72 发布：2017-07-28 实施：2017-07-28

ASTM D4239-2014e1 用高温管式炉燃烧法测定煤和焦炭分析样品中硫含量的标准试验方法
简介：4.1x00a0;Sulfur is part of the ultimate analysis of coal and coke. 4.2x00a0;Results of the sulfur analysis are used for evaluation of coal preparation and cleaning, evaluation of potential sulfur emissions from coal and coke combustion or conversion processes, and evaluation of coal and coke quality in relation to contract specifications, as well as for scientific purposes. 4.3x00a0;The competency of laboratories with respect to use of this standard can be established through reference to Practice D7448. 1.1x00a0;This test method covers the determination of sulfur in samples of coal or coke by high-temperature tube furnace combustion. 1.1.1x00a0;Two analysis methods are described. 1.2x00a0;When automated equipment is used, either method can be classified as an instrumental method. 1.3x00a0;The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4x00a0;All percentages are percent mass fractions unless otherwise noted. 1.5x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：75.160.10 CCS：发布：2014 实施：

GB/T 7405-1987 埋弧炉试验方法
简介：本标准适用于工业用埋弧炉（以下简称埋弧炉），例如用来生产硅铁的埋弧炉。
信息：ICS：25.180 CCS：K61 发布：1987-03-13 实施：1987-11-01

ASTM F2861-2017 不同模式下组合炉增强性能的标准试验方法
简介：5.1x00a0;The energy input rate test and thermostat calibration are used to confirm that the combination oven is operating properly prior to further testing and to ensure that all test results are determined at the same temperature. 5.2x00a0;Preheat energy and time can be useful to food service operators to manage power demands and to know how quickly the combination oven can be ready for operation. 5.3x00a0;Idle energy rate and pilot energy rate can be used to estimate energy consumption during non-cooking periods. 5.4x00a0;Cooking-energy efficiency is a precise indicator of combination oven energy performance under various operating conditions. This information enables the food service operator to consider energy performance when selecting a combination oven. 5.5x00a0;Production capacity can be used by food service operators to choose a combination oven that matches their food output requirements. 5.6x00a0;Water consumption characterization is useful for estimating water and sewage costs associated with combination oven operation. 5.7x00a0;Condensate temperature measurement is useful to verify that the condensate temperature does not violate applicable building codes. 5.8x00a0;Cooking uniformity provides information regarding the combination ovenx2019;s ability to cook food at the same rate throughout the oven compartment. 1.1x00a0;This test method covers the evaluation of the energy and water consumption and the cooking performance of combination ovens that can be operated in hot air convection, steam, and the combination of both hot air convection and steam modes. The test method is also applicable to convection ovens with moisture injection. The results of this test method can be used to evaluate a combination oven and understand its energy consumption. 1.2x00a0;This test method is applicable to gas and electric combination ovens that can be operated in convection, steam and combination modes. 1.3x00a0;The combination oven can be evaluated with respect to the following (where applicable): 1.3.1x00a0;Energy input rate and thermostat calibration (10.2). 1.3.2x00a0;Preheat energy consumption and time (10.3). 1.3.3x00a0;Idle energy rate in convection, steam and combination modes (10.4). 1.3.4x00a0;Pilot energy rate (if applicable) (10.5). 1.3.5x00a0;Cooking-ene......
信息：ICS：97.040.20 CCS：Y68 发布：2017 实施：

ASTM D4239-2014 采用高温管式炉燃烧法测定煤和焦炭分析样品中硫含量的标准试验方法
简介：4.1x00a0;Sulfur is part of the ultimate analysis of coal and coke. 4.2x00a0;Results of the sulfur analysis are used for evaluation of coal preparation and cleaning, evaluation of potential sulfur emissions from coal and coke combustion or conversion processes, and evaluation of coal and coke quality in relation to contract specifications, as well as for scientific purposes. 4.3x00a0;The competency of laboratories with respect to use of this standard can be established through reference to Practice D7448. 1.1x00a0;This test method covers the determination of sulfur in samples of coal or coke by high-temperature tube furnace combustion. 1.1.1x00a0;Two analysis methods are described. 1.2x00a0;When automated equipment is used, either method can be classified as an instrumental method. 1.3x00a0;The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4x00a0;All percentages are percent mass fractions unless otherwise noted. 1.5x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：75.160.10 (Solid fuels) CCS：D21 发布：2014 实施：

GB/T 6542-1986 直接电弧炉的试验方法
简介：本标准适用于额定容量等于或大于0.5t的工业用三相直接电弧炉。这类炉子既适用于固态炉料，也适用于液态炉料，工作时炉内气压等于或接近于大气压。本标准中除了特别指明是三相电弧炉的条款之外，其他条款也适用于一个或多个电极的电弧炉。这些电炉用来熔炼黑色金属（钢、铸铁）和有色金属（铜）；也可作为保温炉供液态炉料在浇铸前的过热和保温用。注：所有电气试验都要排除无功功率补偿和（或）电压稳定装置的影响。如果在试验期间不能关断这些装置，则本标准中有关主电路的各条仍然适用，只是应指出无功功率补偿装置和（或）电压稳定装置也同时投入工作，并须补充说明适用的供电网和这类装置的影响。
信息：ICS：25.180.10 CCS：K61 发布：1986-07-01 实施：1987-07-01

ASTM A991/A991M-2017 热处理钢产品用炉的温度传导均匀性测量标准试验方法
简介：4.1x00a0;Furnaces for heat treatment of steel products are used in many industries, in many ways. Regardless of heat treat furnace type, or processing cycle, it may be necessary for users to know the temperature uniformity in the furnace and whether the material is processed in a zone within the furnace that is capable of meeting the applicable permissible temperature variation requirements. 4.2x00a0;The procedures in this test method may be used by those using, manufacturing, and providing calibration service for, heat treat furnaces used to process steel products. 1.1x00a0;This test method covers the procedures used to conduct a temperature uniformity survey on a furnace used to heat treat steel products. This method is used to determine the capability of the furnace to meet the permissible temperature variation specified in the applicable product specification, or as agreed to by the purchaser and supplier of heat treat services. Survey documentation requirements, and the procedure used to subsequently establish the furnace working zone, are defined in this test method. 1.2x00a0;This test method covers heat treat furnaces in any of the following categories: 1.2.1x00a0;Continuous or semi-continuous conveyance furnaces, 1.2.2x00a0;Batch furnaces, and 1.2.3x00a0;Salt or liquid baths and fluidized beds. 1.3x00a0;This test method only applies when specified in the product specification or the purchase order. 1.4x00a0;Controlling a heat treatment of steel products using thermocouples attached to the extremities of each load is an alternative to performing a furnace survey. 1.5x00a0;By mutual agreement between the purchaser and the supplier of heat treat services, more stringent and/or additional requirements may be specified. The acceptance of any such additional requirements shall be dependent on negotiations with the supplier and must be included in the order as agreed upon by the purchaser and supplier. 1.6x00a0;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.7x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.8x00a0;This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the ......
信息：ICS：25.200 CCS：J36 发布：2017 实施：

ASTM F3051-2014 煮炉和烤箱性能的标准试验方法
简介：5.1x00a0;The energy input rate test is used to confirm that the cook-and-hold oven is operating properly prior to further testing. 5.2x00a0;Preheat energy and time can be useful to food service operators to manage power demands and to know how quickly the cook-and-hold oven can be ready for operation. 5.3x00a0;Idle energy rate and pilot energy rate can be used to estimate energy consumption during non-cooking periods. 5.4x00a0;Energy utilization factor is a precise indicator of a cook-and-hold ovenx2019;s energy performance while cooking and holding a typical food product under various loading conditions. If energy performance information is desired using a food product other than the specified test food, the test method could be adapted and applied. Energy performance information allows an end user to better understand the operating characteristics of a cook-and-hold oven. 5.5x00a0;Production capacity information can help an end user to better understand the production capabilities of a cook-and-hold oven as it is used to cook a typical food product and this could help in specifying the proper size and quantity of equipment. If production information is desired using a food product other than the specified test food, the test method could be adapted and applied. 5.6x00a0;Holding energy rate may be used to determine the cost of holding cooked product in the cook-and-hold oven. 5.7x00a0;Product yield may be used by the food service operator to compare relative product output from one cook-and-hold oven to another. Additionally, product shrinkage during holding may be used by the food service operator to evaluate the cook-and-hold ovenx2019;s performance when holding cooked product. 1.1x00a0;This test method evaluates the energy consumption and cooking performance of cook-and-hold ovens. The food service operator can use this evaluation to select a cook-and-hold oven and understand its energy consumption. 1.2x00a0;This test method is applicable to gas and electric cook-and-hold ovens. 1.3x00a0;The cook-and-hold oven can be evaluated with respect to the following (where applicable): 1.3.1x00a0;Energy input rate (10.2). 1.3.2x00a0;Preheat energy consumption and time (10.3). 1.3.3x00a0;Idle energy rate (10.4). 1.3.4x00a0;Pilot energy rate (if applicable) (10.5). 1.3.5x00a0;Cooking energy rate, and production capacity (10.7).
信息：ICS：97.040.20 (Cooking ranges, working tables, ovens a CCS：发布：2014 实施：

GB/T 10066.11-2016 电热装置的试验方法第11部分:埋弧炉
简介：
信息：ICS： CCS：发布：实施：2016-09-01

BS ISO 17493-2016 耐热服装和设备.采用热空气循环炉对耐热对流的试验方法
简介：
信息：ICS：13.340.10 CCS：C73 发布：2016-12-31 实施：2016-12-31

ASTM F3051-2014(2019) 烹调和保温炉性能的标准试验方法
简介：5.1x00a0;The energy input rate test is used to confirm that the cook-and-hold oven is operating properly prior to further testing. 5.2x00a0;Preheat energy and time can be useful to food service operators to manage power demands and to know how quickly the cook-and-hold oven can be ready for operation. 5.3x00a0;Idle energy rate and pilot energy rate can be used to estimate energy consumption during non-cooking periods. 5.4x00a0;Energy utilization factor is a precise indicator of a cook-and-hold ovenx2019;s energy performance while cooking and holding a typical food product under various loading conditions. If energy performance information is desired using a food product other than the specified test food, the test method could be adapted and applied. Energy performance information allows an end user to better understand the operating characteristics of a cook-and-hold oven. 5.5x00a0;Production capacity information can help an end user to better understand the production capabilities of a cook-and-hold oven as it is used to cook a typical food product and this could help in specifying the proper size and quantity of equipment. If production information is desired using a food product other than the specified test food, the test method could be adapted and applied. 5.6x00a0;Holding energy rate may be used to determine the cost of holding cooked product in the cook-and-hold oven. 5.7x00a0;Product yield may be used by the food service operator to compare relative product output from one cook-and-hold oven to another. Additionally, product shrinkage during holding may be used by the food service operator to evaluate the cook-and-hold ovenx2019;s performance when holding cooked product. 1.1x00a0;This test method evaluates the energy consumption and cooking performance of cook-and-hold ovens. The food service operator can use this evaluation to select a cook-and-hold oven and understand its energy consumption. 1.2x00a0;This test method is applicable to gas and electric cook-and-hold ovens. 1.3x00a0;The cook-and-hold oven can be evaluated with respect to the following (where applicable): 1.3.1x00a0;Energy input rate (10.2). 1.3.2x00a0;Preheat energy consumption and time (10.3). 1.3.3x00a0;Idle energy rate (10.4). 1.3.4x00a0;Pilot energy rate (if applicable) (10.5). 1.3.5x00a0;Cooking energy rate, and production capacity (10.7)......
信息：ICS：97.040.20 CCS：Y68 发布：2014 实施：

ASTM D6071-14(2022) 用石墨炉原子吸收光谱法测定高纯度水中低含量钠的标准试验方法
简介：
信息：ICS：71.040.50 CCS：发布：2022-11-01 实施：

BS ISO 17493-2016 耐热服装和设备.采用热空气循环炉对耐热对流的试验方法
简介：
信息：ICS：13.340.10 CCS：C73 发布：2016-12-31 实施：2016-12-31

ASTM D4239-2014e2 采用高温管式炉燃烧法测定煤和焦炭分析样品中硫含量的标准试验方法
简介：4.1x00a0;Sulfur is part of the ultimate analysis of coal and coke. 4.2x00a0;Results of the sulfur analysis are used for evaluation of coal preparation and cleaning, evaluation of potential sulfur emissions from coal and coke combustion or conversion processes, and evaluation of coal and coke quality in relation to contract specifications, as well as for scientific purposes. 4.3x00a0;The competency of laboratories with respect to use of this standard can be established through reference to Practice D7448. 1.1x00a0;This test method covers the determination of sulfur in samples of coal or coke by high-temperature tube furnace combustion. 1.1.1x00a0;Two analysis methods are described. 1.2x00a0;When automated equipment is used, either method can be classified as an instrumental method. 1.3x00a0;The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4x00a0;All percentages are percent mass fractions unless otherwise noted. 1.5x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：75.160.10 CCS：发布：2014 实施：

ASTM E2652-22 在750℃下使用带有锥形气流稳定器的管式炉评估材料燃烧性的标准试验方法 °C温度
简介：
信息：ICS：13.220.50 CCS：发布：2022-11-01 实施：

ASTM F3216-16 回火炉性能的标准试验方法
简介：
信息：ICS：97.040.20 CCS：发布：2016-10-01 实施：

GOST R 55994-2014 耐火试验. 非炉基大规模试验和模拟的设计与指挥指南
简介：
信息：ICS：13.220.40 CCS：发布：2014 实施：2015-01-01

ASTM D6357-21b 用电感耦合等离子体原子发射光谱法、电感耦合等离子体质谱法和石墨炉原子吸收光谱法测定煤炭利用过程中煤炭、焦炭和燃烧残渣中微量元素的标准试验方法
简介：
信息：ICS：75.160.10 CCS：发布：2021-12-01 实施：

ASTM D5016-16 采用高温管式炉燃烧法红外吸收法测定煤炭和焦炭燃烧残渣中总硫的标准试验方法
简介：
信息：ICS：75.160.10 CCS：发布：2016-09-01 实施：

DIN 55968-2013 颜料. 工业生产的颜料炭黑 (焰黑, 炉法炭黑, 煤气炭黑). 要求和试验方法
简介：
信息：ICS：87.060.10 CCS：G53 发布：2013-08 实施：

ASTM D6357-21a 用电感耦合等离子体原子发射光谱法、电感耦合等离子体质谱法和石墨炉原子吸收光谱法测定煤炭利用过程中煤炭、焦炭和燃烧残渣中微量元素的标准试验方法
简介：
信息：ICS：75.160.10 CCS：发布：2021-06-11 实施：

BS EN ISO 13078-2-2016 牙科. 牙科用炉. 通过烧釉评估炼炉程序的试验方法
简介：
信息：ICS：11.060.01 CCS：C33 发布：2016-08-31 实施：2016-08-31

ASTM F1496-13 对流炉性能的标准试验方法
简介：
信息：ICS：97.040.20 CCS：发布：2013-06-01 实施：

ASTM D6357-21 用电感耦合等离子体原子发射光谱法电感耦合等离子体质谱法和石墨炉原子吸收光谱法测定煤中痕量元素的标准试验方法
简介：
信息：ICS：75.160.10 CCS：发布：2021-04-01 实施：

BS EN ISO 13078-2-2016 牙科. 牙科用炉. 通过烧釉评估炼炉程序的试验方法
简介：
信息：ICS：11.060.01 CCS：C33 发布：2016-08-31 实施：2016-08-31

NF S91-277-2013 牙科.牙科用炉.带有单独热电偶的温度测量试验方法
简介：
信息：ICS：11.060.20 CCS：C33 发布：2013-05-03 实施：2013-05-03

ASTM D6732-04(2020) 石墨炉原子吸收光谱法测定喷射燃料中铜的标准试验方法
简介：
信息：ICS：71.040.50 CCS：发布：2020-05-01 实施：

EN ISO 13078-2-2016 牙科牙炉-第2部分:通过烧釉炉方案评价的试验方法(ISO 13078-2:2016)
简介：Dieses Dokument legt einen Brenngrad fest, der vom Anwender einzuhalten ist. Es beschreibt ein Prüfverfahren zur Anpassung des Brennprogramms eines dentalen Brennofens indem der Brenngrad von gebrannten Probekörpern für eine Dentalkeramik bestimmt wird. Das Prüfverfahren ist für pulverförmige Dentalkeramiken nach ISO 6872, Typ I, geeignet. Das Prüfverfahren ermöglicht die Prüfung der Temperaturführung im dentalen Brennofen durch die Beurteilung des Brenngrades einer Dentalkeramik. Das Prüfverfahren ist auch zur Beurteilung der Reproduzierbarkeit der Brände in einem dentalen Brennofen oder zum Vergleich von mehreren dentalen Brennöfen geeignet.
信息：ICS：11.060.01 CCS：C33 发布：2016-08 实施：

DIN EN ISO 13078-2013 牙科.牙科用炉.带有单独热电偶的温度测量试验方法(ISO 13078-2013).德文版本EN ISO 13078-2013
简介：
信息：ICS：11.060.20 CCS：C33 发布：2013-05 实施：

ASTM E136-19a 在750xb0；C下用竖管炉评定材料燃烧性的标准试验方法
简介：
信息：ICS：13.220.50 CCS：发布：2019-12-15 实施：

ISO 13078-2-2016 牙科. 牙科用炉. 第2部分: 通过烧釉评估炼炉程序的试验方法
简介：
信息：ICS：11.060.01 CCS：发布：2016-07 实施：

ASTM D3012-13 用炉内试样旋转器测定聚丙烯热氧化稳定性的标准试验方法
简介：
信息：ICS：83.080.20 CCS：发布：2013-04-01 实施：

ASTM D6357-19 用电感耦合等离子体原子发射光谱法电感耦合等离子体质谱法和石墨炉原子吸收光谱法测定煤中痕量元素的标准试验方法
简介：
信息：ICS：75.160.10 CCS：发布：2019-08-01 实施：

ASTM E2652-2016 750 ℃下带锥形空气流稳定器的管式炉材料性能的标准试验方法
简介：5.1x00a0;While actual building fire exposure conditions are not duplicated, this test method will assist in indicating those materials which do not act to aid combustion or add appreciable heat to an ambient fire. 5.2x00a0;This test method does not apply to laminated or coated materials. 5.3x00a0;This test method is technically equivalent to ISO 1182. 1.1x00a0;This fire-test-response test method covers the determination under specified laboratory conditions of combustion characteristics of building materials. 1.2x00a0;Limitations of this fire-test response test method are shown below. 1.2.1x00a0;This test method does not apply to laminated or coated materials. 1.2.2x00a0;This test method is not suitable or satisfactory for materials that soften, flow, melt, intumesce or otherwise separate from the measuring thermocouple. 1.2.3x00a0;This test method does not provide a measure of an intrinsic property. 1.2.4x00a0;This test method does not provide a quantitative measure of heat generation or combustibility; it simply serves as a test method with selected (end point) measures of combustibility. 1.2.5x00a0;This test method does not measure the self-heating tendencies of materials. 1.2.6x00a0;In this test method materials are not being tested in the nature and form used in building aplications. The test specimen consists of a small, specified volume that is either (1) cut from a thick sheet; (2) assembled from multiple thicknesses of thin sheets; or (3) placed in a container if composed of grarnular powder or loose fiber materials. 1.2.7x00a0;Results from this test method apply to the specific test apparatus and test conditions and are likely to vary when changes are made to one or more of the following: (1) the size, shape, and arrangement of the specimen; (2) the distribution of organice content; (3) the exposure temperature; (4) the air supply; (5) the location of thermocouples. 1.3x00a0;This test method references notes and footnotes that provide explanatory information. These notes and footnotes, excluding those in tables and figure......
信息：ICS：13.220.50 CCS：发布：2016 实施：

BS EN ISO 13078-2013 牙科.牙科用炉.带有单独热电偶的温度测量试验方法
简介：
信息：ICS：11.060.20 CCS：C33 发布：2013-02-28 实施：2013-02-28

ASTM F1496-13(2019) 对流炉性能的标准试验方法
简介：
信息：ICS：97.040.20 CCS：发布：2019-05-01 实施：

ASTM E136-2016 750 ℃下立式管炉材料特性的标准试验方法
简介：5.1x00a0;While actual building fire exposure conditions are not duplicated, this test method will assist in indicating those materials which do not act to aid combustion or add appreciable heat to an ambient fire. 5.2x00a0;Materials passing the test are permitted limited flaming and other indications of combustion. 1.1x00a0;This fire-test-response test method covers the determination under specified laboratory conditions of combustion characteristics of building materials. 1.2x00a0;Limitations of this fire-test response test method are shown below. 1.2.1x00a0;This test method does not apply to laminated or coated materials. 1.2.2x00a0;This test method is not suitable or satisfactory for materials that soften, flow, melt, intumesce or otherwise separate from the measuring thermocouple. 1.2.3x00a0;This test method does not provide a measure of an intrinsic property. 1.2.4x00a0;This test method does not provide a quantitative measure of heat generation or combustibility; it simply serves as a test method with selected (end point) measures of combustibility. 1.2.5x00a0;The test method does not measure the self-heating tendencies of materials. 1.2.6x00a0;In this test method materials are not being tested in the nature and form used in building applications. The test specimen consists of a small, specified volume that is either (1) cut from a thick sheet; (2) assembled from multiple thicknesses of thin sheets; or (3) placed in a container if composed of granular powder or loose-fiber materials. 1.2.7x00a0;Results from this test method apply to the specific test apparatus and test conditions and are likely to vary when changes are made to one or more of the following: (1) the size, shape, and arrangement of the specimen; (2) the distribution of organic content; (3) the exposure temperature; (4) the air supply; (5) the location of thermocouples. 1.3x00a0;This test method includes two options, both of which use a furnace to expose test specimens of building materials to a temperature of 750x00b0;C (1382x00b0;F). 1.3.1x00a0;The furnace for the appa......
信息：ICS：13.220.50 ; 91.100.01 CCS：发布：2016 实施：

ISO 13078-2013 牙科.牙科用炉.带有单独热电偶的温度测量试验方法
简介：
信息：ICS：11.060.20 CCS：C33 发布：2013-02 实施：

ASTM D3012-19 用炉内试样旋转器测定聚丙烯热氧化稳定性的标准试验方法
简介：
信息：ICS：83.080.20 CCS：发布：2019-04-01 实施：

KS C IEC 62076-2015 工业电加热装置.感应槽炉和坩埚感应炉的试验方法
简介：
信息：ICS：25.180.10 CCS：M70 发布：2015-04-15 实施：

ASTM D6071-13 石墨炉原子吸收光谱法测定高纯度水中低浓度钠的标准试验方法
简介：
信息：ICS：71.040.50 CCS：发布：2013-01-01 实施：

ASTM F2894-19 用热空气循环炉评定耐热材料、防护服和设备的标准试验方法
简介：
信息：ICS：13.340.01 CCS：发布：2019-04-01 实施：

ASTM D6732-04(2015) 石墨炉原子吸收光谱法测定喷射燃料中铜的标准试验方法
简介：
信息：ICS：71.040.50 CCS：发布：2015-04-01 实施：

ASTM E1852-2013 采用石墨炉原子吸收光谱法测定碳和低合金钢中低水平锑的标准试验方法
简介：5.1x00a0;This test method is utilized for the determination of trace levels of antimony in carbon and low-alloy steel. It is assumed that the procedure will be performed by trained analysts capable of performing common laboratory practices skillfully and safely. It is expected that the work will be performed in a properly equipped laboratory and proper waste disposal procedures will be followed. 1.1x00a0;This test method covers the determination of antimony in carbon and low-alloy steel in the 0.00058201;% through 0.0108201;% range. 1.2x00a0;If this test method is used to test materials having contents less than 0.0018201;% antimony, users of different laboratories will experience more than the usual 58201;% risk that their results will differ by more than 508201;% relative error. 1.3x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：71.040.500; 71.040.50 (Physicochemical methods of CCS：发布：2013 实施：

ASTM E136-19 在750xb0；C下用竖管炉评定材料燃烧性的标准试验方法
简介：
信息：ICS：13.220.50 CCS：发布：2019-02-01 实施：

ASTM F2861-2015 不同模式下组合炉增强性能的标准试验方法
简介：5.1x00a0;The energy input rate test and thermostat calibration are used to confirm that the combination oven is operating properly prior to further testing and to ensure that all test results are determined at the same temperature. 5.2x00a0;Preheat energy and time can be useful to food service operators to manage power demands and to know how quickly the combination oven can be ready for operation. 5.3x00a0;Idle energy rate and pilot energy rate can be used to estimate energy consumption during non-cooking periods. 5.4x00a0;Cooking-energy efficiency is a precise indicator of combination oven energy performance under various operating conditions. This information enables the food service operator to consider energy performance when selecting a combination oven. 5.5x00a0;Production capacity can be used by food service operators to choose a combination oven that matches their food output requirements. 5.6x00a0;Water consumption characterization is useful for estimating water and sewage costs associated with combination oven operation. 5.7x00a0;Condensate temperature measurement is useful to verify that the condensate temperature does not violate applicable building codes. 5.8x00a0;Cooking uniformity provides information regarding the combination ovenx2019;s ability to cook food at the same rate throughout the oven compartment. 1.1x00a0;This test method covers the evaluation of the energy and water consumption and the cooking performance of combination ovens that can be operated in hot air convection, steam, and the combination of both hot air convection and steam modes. The test method is also applicable to convection ovens with moisture injection. The results of this test method can be used to evaluate a combination oven and understand its energy consumption. 1.2x00a0;This test method is applicable to gas and electric combination ovens that can be operated in convection, steam and combination modes. 1.3x00a0;The combination oven can be evaluated with respect to the following (where applicable): 1.3.1x00a0;Energy input rate and thermostat calibration (10.2). 1.3.2x00a0;Preheat energy consumption and time (10.3). 1.3.3x00a0;Idle energy rate in convection, steam and combination modes (10.4). 1.3.4x00a0;Pilot energy rate (if applicable) (10.5). 1.3.5x00a0;Cooking-energ......
信息：ICS：97.040.20 CCS：发布：2015 实施：

ASTM D4239-2013e1 利用高温管式炉燃烧法测定煤和焦炭分析样品中硫含量的标准试验方法
简介：4.1x00a0;Sulfur is part of the ultimate analysis of coal and coke. 4.2x00a0;Results of the sulfur analysis are used for evaluation of coal preparation and cleaning, evaluation of potential sulfur emissions from coal and coke combustion or conversion processes, and evaluation of coal and coke quality in relation to contract specifications, as well as for scientific purposes. 4.3x00a0;The competency of laboratories with respect to use of this standard can be established through reference to Practice D7448. 1.1x00a0;This test method covers the determination of sulfur in samples of coal or coke by high-temperature tube furnace combustion. 1.1.1x00a0;Two analysis methods are described. 1.2x00a0;When automated equipment is used, either method can be classified as an instrumental method. 1.3x00a0;The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：75.160.10 (Solid fuels) CCS：D21 发布：2013 实施：

ASTM E2652-18 在750℃下用带锥形气流稳定器的管式炉评定材料燃烧性的标准试验方法
简介：
信息：ICS：13.220.50 CCS：发布：2018-12-15 实施：

ASTM D6071-14 石墨炉原子吸收光谱法测定高纯度水中低浓度钠的标准试验方法
简介：
信息：ICS：71.040.50 CCS：发布：2014-09-15 实施：

ASTM D4239-2013 高温管式炉燃烧法测定煤和焦炭分析样品中硫含量的标准试验方法
简介：4.1x00a0;Sulfur is part of the ultimate analysis of coal and coke. 4.2x00a0;Results of the sulfur analysis are used for evaluation of coal preparation and cleaning, evaluation of potential sulfur emissions from coal and coke combustion or conversion processes, and evaluation of coal and coke quality in relation to contract specifications, as well as for scientific purposes. 4.3x00a0;The competency of laboratories with respect to use of this standard can be established through reference to Practice D7448. 1.1x00a0;This test method covers the determination of sulfur in samples of coal or coke by high-temperature tube furnace combustion. 1.1.1x00a0;Two analysis methods are described. 1.2x00a0;When automated equipment is used, either method can be classified as an instrumental method. 1.3x00a0;The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：75.160.10 (Solid fuels) CCS：D21 发布：2013 实施：

ASTM E1834-18 用石墨炉原子吸收光谱法分析镍合金的标准试验方法
简介：
信息：ICS：77.120.40 CCS：发布：2018-12-01 实施：

NB/T 34016-2014 生物质炕炉试验方法
简介：本标准规定了生物质炕炉的热性能试验方法和烟气排放的污染物检测方法。本标准适用于燃用生物质及其成型燃料，以火炕供暖为主，或兼有其他功能(热水采暖、炊事)的炉具。
信息：ICS：19.020 CCS：F13 发布：2014-06-29 实施：2014-11-01

GOST R ISO 17493-2013 职业安全标准体系. 防热服和设备. 热空气循环炉进行抗热对流的试验方法
简介：
信息：ICS：13.220.40;13.340.10 CCS：发布：2013 实施：2014-12-01