吸音检测标准吸音-中析研究所检测

(CMA)

(CNAS)

(ISO)

(高新技术企业)

吸音相关标准参考信息

GB/T 33620-2017 纺织品吸音性能的检测和评价
简介：
信息：ICS：59.080.30 CCS：W04 发布：2017-05-12 00:00:00.0 实施：2017-12-01 00:00:00.0

ASTM E1264-2014 吸音顶棚产品的标准分类
简介：4.1x00a0;This classification is used to classify and aid in the selection of acoustical ceiling products. 1.1x00a0;This classification covers ceiling products that provide acoustical performance and interior finish in buildings. Products used in performance spaces and other special applications may require more detailed specification than provided by this classification. 1.2x00a0;This classification classifies acoustical ceilings by type, pattern, and certain ratings for acoustical performance, light reflectance, and fire safety. It does not cover the aspects of acoustical ceilings when used as a component of a system or assembly tested for fire endurance or floor/ceiling sound transmission. 1.3x00a0;This classification does not include physical properties, such as structural hardness, friability, sag, linear expansion and contraction, and transverse strength, which may affect the handling, installation, and use of acoustical ceiling products (see Test Methods C367). 1.4x00a0;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
信息：ICS：91.060.30 CCS：发布：2014 实施：

ASTM C636/C636M-2008 吸音砖和衬板用金属吊顶系统安装的标准实施规程
简介：1.1 This practice covers the installation of suspension systems for acoustical tile and lay-in panels. It is applicable to contractors whose services are utilized for installing acoustical ceilings and to other trades if their activities are responsible for interference with ceiling components or performance as defined in this recommended practice. 1.2 While the practices described in this document have equal application to rated fire-resistive suspension systems, additional requirements may have been imposed to obtain the fire endurance classification of particular floor-ceiling or roof-ceiling assemblies. These details should be obtained from the manufacturers. 1.3 Similarly, additional detailing may be necessary to meet sound attenuation requirements when ceiling plenums extend over contiguous rooms. These, too, should be obtained from the manufacturer of the acoustical material employed. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.5 While many of the practices described in this practice have application to the installation of metal suspension systems in exterior environments, the specific design of exterior ceiling installations requires the review and approval of the architect or engineer, or both, who are responsible for the construction of the building or modifications to an existing building. While recommendations from the manufacturer should be solicited, it remains the final responsibility of the architect/engineer to ensure proper application of the materials in question. 1.6 This standard does not purport to address of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：91.120.20 (Acoustics in buildings. Sound insulatio CCS：P32 发布：2008 实施：

ASTM C1534-22 用作管道系统热和吸音衬垫的柔性聚合物泡沫板绝缘材料的标准规范
简介：
信息：ICS：91.100.60 CCS：发布：2022-11-01 实施：

NF F90-272-1-2013 轨道交通.轨道. 作用于空气传声的隔音屏障及相关设备. 测定声学性能的试验方法. 第1部分: 本质特征. 扩散声场条件下实验室内的吸音作用
简介：
信息：ICS：93.100 CCS：S11 发布：2013-01-12 实施：2013-01-12

ASTM C1014-2008(2013) 喷施的矿物纤维吸热和吸音绝缘材料的标准规格
简介：1.1x00a0;This specification covers the composition and the physical properties of spray-applied mineral fiber thermal and sound absorbing insulation. 1.2x00a0;These mineral fibers shall be pneumatically conveyed to a spray nozzle where they are mixed with water. These mineral fibers shall have a binder either pre-mixed with the fibers or added at the spray nozzle with the water. 1.3x00a0;The spray-applied mineral fiber insulation is intended for use in building constructions at ambient conditions. 1.4x00a0;This is a material specification only and is not intended to cover methods of application that are supplied by the manufacturer. 1.5x00a0;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：91.120.10 (Thermal insulation of buildings); 91.12 CCS：Q25 发布：2008 实施：

T/SCDA 035-2022 申音爵（HF）材料保温隔声吸音应用技术标准
简介：导热系数W/(m·k)≤0.029计权撞击声改善量、ΔLW（dB）≥20
信息：ICS：91.100.01 CCS：E4710 发布：2022-06-24 实施：2022-07-28

NF S31-026-2013 声学.利用声压测定噪音源的声功率级.吸音室和半消音室的精确方法
简介：
信息：ICS：17.140.01 CCS：Z32 发布：2013-01-12 实施：2013-01-12

YC/T 234.3-2007 薄平板冲切结构要素第3部分:吸音胶粘接板
简介：YC/T 234的本部分规定了薄平板吸音胶粘接板工艺孔的型式和尺寸。本部分适用于薄平板吸音胶粘接板的设计和制造。
信息：ICS：65.160 CCS：X94 发布：2007-07-05 实施：2007-09-01

T/QGCML 267-2022 石膏基内墙吸音腻子
简介：本文件规定了石膏基内墙吸音腻子的术语和定义、命名规则和分类、一般要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存。本文件适用于石膏基内墙吸音腻子的生产和使用。
信息：ICS：91.100.01 CCS：E501 发布：2022-04-08 实施：2022-04-08

DIN EN 16272-1-2013 铁路应用设施.轨道.隔声板和相关对空气声音传播有作用的设备.声学性能测定试验方法.第1部分:本质特征.扩散声场条件下实验室内吸音作用.德文版本EN 16272-1-2012
简介：This European Standard specifies the laboratory method for measuring the sound absorption of flat noise barriers or flat claddings for retaining walls or tunnels. It covers the assessment of the intrinsic sound absorption performance of noise barriers and related devices acting on airborne sound propagation designed for railways which can reasonably be assembled inside the testing facility described in EN ISO 354. The test method in EN ISO 354, referred to in this European Standard, is strictly valid only for flat absorbers and in particular excludes devices which act as slightly damped resonators. Some devices will depart significantly from these requirements and in these cases care is needed in interpreting the results.
信息：ICS：93.100 CCS：S11 发布：2013-01 实施：

ASTM C635/C635M-2007 吸音瓦及铺设顶栅镶板用金属悬吊装置的生产、性能和试验的标准规范
简介：1.1 This specification covers metal ceiling suspension systems used primarily to support acoustical tile or acoustical lay-in panels.1.2 Some suspension systems incorporate locking assembly details that enhance performance by providing some continuity or load transfer capability between adjacent sections of the ceiling grid. The test methods included in this specification do not provide the means for making a complete evaluation of continuous beam systems, nor for assessing the continuity contribution to overall system performance. However, the test methods can be used for evaluating primary structural members in conjunction with secondary members that interlock, as well as with those of noninterlocking type.1.3 While this specification is applicable to the exterior installation of metal suspension systems, the atmospheric conditions and wind loading require additional design attention to ensure safe implementation. For that reason, a specific review and approval should be solicited from the responsible architect and engineer, or both, for any exterior application of metal suspension systems in the construction of a new building or building modification.1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.1.5 The following safety hazards caveat pertains only to the test methods described in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：91.120.20 CCS：P32 发布：2007 实施：

T/SCDA 035-2021 申音爵（HF）材料保温隔声吸音应用技术标准
简介：1.为规范申音爵（HF）材料保温、隔声、吸音在房屋建筑墙体、楼板中应用，确保申音爵（HF）材料保温、隔声、吸音的工程应用质量，制定本标准。2.本标准适用于新建、改建、扩建及既有房屋建筑墙体、楼板隔声的设计、施工和验收。3.申音爵（HF）材料保温、隔声、吸音在房屋建筑工程中应用，除应执行本标准外，尚应符合现行国家、行业及本市有关标准的规定。
信息：ICS：91.100.60 CCS：E509 发布：2021-06-28 实施：2021-07-08

ASTM C636/C636M-2013 吸音砖和衬板用金属吊顶系统安装的标准实施规程
简介：1.1x00a0;This practice covers the installation of suspension systems for acoustical tile and lay-in panels. It is applicable to contractors whose services are utilized for installing acoustical ceilings and to other trades if their activities are responsible for interference with ceiling components or performance as defined in this recommended practice. 1.2x00a0;While the practices described in this document have equal application to rated fire-resistive suspension systems, additional requirements may have been imposed to obtain the fire endurance classification of particular floor-ceiling or roof-ceiling assemblies. These details should be obtained from the manufacturers. 1.3x00a0;Similarly, additional detailing may be necessary to meet sound attenuation requirements when ceiling plenums extend over contiguous rooms. These, too, should be obtained from the manufacturer of the acoustical material employed. 1.4x00a0;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.5x00a0;While many of the practices described in this practice have application to the installation of metal suspension systems in exterior environments, the specific design of exterior ceiling installations requires the review and approval of the architect or engineer, or both, who are responsible for the construction of the building or modifications to an existing building. While recommendations from the manufacturer should be solicited, it remains the final responsibility of the architect/engineer to ensure proper application of the materials in question. 1.6x00a0;This standard does not purport to address of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：91.120.20 (Acoustics in buildings. Sound insulatio CCS：P32 发布：2013 实施：

CNS 10468-2006 吸音用轻质纤维板
简介：本标准适用于吸音为目的之轻质纤维板。
信息：ICS：79.060.20 CCS：发布：2006-10-31 实施：2006-10-31

T/ZZB 1740-2020 环保型车用双组份吸音棉
简介：本文件规定了环保型车用双组份吸音棉的术语和定义、基本要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存及质量承诺。本文件适用于由PP和PET为主要材料的车用双组份吸音材料。
信息：ICS：59.060.99 CCS：C178 发布：2020-10-23 实施：2020-11-06

ASTM C635/C635M-2013 吸音瓦及铺设顶栅镶板用金属悬吊装置的生产、性能和试验的标准规范
简介：1.1x00a0;This specification covers metal ceiling suspension systems used primarily to support acoustical tile or acoustical lay-in panels. 1.2x00a0;Some suspension systems incorporate locking assembly details that enhance performance by providing some continuity or load transfer capability between adjacent sections of the ceiling grid. The test methods included in this specification do not provide the means for making a complete evaluation of continuous beam systems, nor for assessing the continuity contribution to overall system performance. However, the test methods can be used for evaluating primary structural members in conjunction with secondary members that interlock, as well as with those of noninterlocking type. 1.3x00a0;While this specification is applicable to the exterior installation of metal suspension systems, the atmospheric conditions and wind loading require additional design attention to ensure safe implementation. For that reason, a specific review and approval should be solicited from the responsible architect and engineer, or both, for any exterior application of metal suspension systems in the construction of a new building or building modification. 1.4x00a0;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.5x00a0;The following safety hazards caveat pertains only to the test methods described in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：91.120.20 (Acoustics in buildings. Sound insulatio CCS：P32 发布：2013 实施：

GM 9986185-2005 预聚物低MDI聚氨酯吸音泡沫
简介：Freigabemuster, für die diese Vorschrift zutrifft, müssen nach dieser Vorschrift geprüft werden und von der Produktentwicklung und Konstruktion genehmigt sein
信息：ICS： CCS：T04 发布：2005-08-01 实施：

T/SCDA 035-2020 申音爵（SpaceQt) 材料隔声、吸音应用技术标准
简介：计权撞击声改善量△LW，dB≥20GB/T19889.8
信息：ICS：91.100.01 CCS：E4710 发布：2020-09-07 实施：2020-05-26

ASTM C635/C635M-2013a 吸音瓦及铺设顶栅镶板用金属悬吊装置的生产、性能和试验的标准规范
简介：1.1x00a0;This specification covers metal ceiling suspension systems used primarily to support acoustical tile or acoustical lay-in panels. 1.2x00a0;Some suspension systems incorporate locking assembly details that enhance performance by providing some continuity or load transfer capability between adjacent sections of the ceiling grid. The test methods included in this specification do not provide the means for making a complete evaluation of continuous beam systems, nor for assessing the continuity contribution to overall system performance. However, the test methods can be used for evaluating primary structural members in conjunction with secondary members that interlock, as well as with those of noninterlocking type. 1.3x00a0;While this specification is applicable to the exterior installation of metal suspension systems, the atmospheric conditions and wind loading require additional design attention to ensure safe implementation. For that reason, a specific review and approval should be solicited from the responsible architect and engineer, or both, for any exterior application of metal suspension systems in the construction of a new building or building modification. 1.4x00a0;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.5x00a0;The following safety hazards caveat pertains only to the test methods described in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：91.120.20 (Acoustics in buildings. Sound insulatio CCS：发布：2013 实施：

ASTM E795-2005 吸音试验过程中安装试样的标准实施规程
简介：The sound absorption of a material that covers a flat surface depends not only on the physical properties of the material but also on the way in which the material is mounted over the surface. The mountings specified in these practices are intended to simulate in the laboratory conditions that exist in normal use. Some of the specified mountings require special fixtures or minor deviations from normal practice. These fixtures or deviations are to be used only during laboratory tests and should not be specified for practical installations. They are noted in the specifications for the mountings in question by the phrase x201C;for laboratory testing only.x201D; Test reports may refer to these mountings by type designation instead of providing a detailed description of the mounting used.1.1 These practices cover test specimen mountings to be used during sound absorption tests performed in accordance with Test Method C423. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are provided for information only.
信息：ICS：91.120.20 (Acoustics in buildings. Sound insulatio CCS：N65 发布：2005 实施：

KS M ISO 2509-2020 吸音扩展纯瓷砖瓷砖
简介：
信息：ICS： CCS：发布：2020-08-21 实施：

BS EN 16272-1-2012 铁路应用设施.轨道.对空气传声起作用的隔音板和相关设备.声学性能测定用试验方法.本质特征.扩散声场条件下实验室内的吸音作用
简介：
信息：ICS：93.100 CCS：S11 发布：2012-11-30 实施：2012-11-30

ASTM C367-2005 预制建筑用吸音砖和镶入式天花板的强度性能的标准试验方法
简介：Knowledge of hardness is useful in the development and the quality control of acoustical tile and lay-in ceiling panels. Deviation from an established hardness range will assist in pointing out processing errors or defective raw materials, thereby aiding the maintenance of uniform product quality. This property is also useful in comparing the relative abilities of materials to resist indentations on the panel surface caused by impacts. Since the hardness varies with the thickness, only samples of the same thickness may be directly compared.1.1 These test methods cover the determination of the strength properties of prefabricated architectual acoustical tile or lay-in ceiling panels as follows:TestsSectionsHardness4 to 9Friability10 to 16Sag17 to 23Transverse strength24 to 301.2 Not all of the tests described in these test methods may be necessary to evaluate any particular product for a specific use. In each instance, it will be necessary to determine which properties are required.1.3 These test methods specify procedures that may be used in product development, manufacturing control, specification acceptance, and service evaluation.1.4 Properties determined by these test methods reflect the performance of the materials under the specific conditions of the test, and do not necessarily indicate performance under conditions other than those specified herein.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：91.120.20 (Acoustics in buildings. Sound insulatio CCS：Q25 发布：2005 实施：

T/CSWF 003-2020 聚酯纤维吸音装饰板
简介：产品分类1按产品的外观形式分为饰面系列、毛面系列、光面系列和印花系列。2按产品的特性分为阻燃、非阻燃。3型号表示方法要求1外观质量任何1m2板面内允许有1处5mm2~10mm2污斑；任何1m2板面内允许有1处长度≤10mm划痕；但均不影响装饰层。表面不允许有压痕、缺损、龟裂、分层。不允许有明显的色差和光泽不均。2尺寸偏差长度、宽度尺寸偏差不得超过±3.0mm/m厚度偏差不得超过±0.5mm。垂直度偏差不得超过1.0mm/m。边缘直度偏差不得超过1.0mm/m。平整度偏差不得超过0.5mm3理化性能4甲醛释放限量聚酯纤维吸音装饰板甲醛释放限量指标应符合GB18580-2017的要求。
信息：ICS：59.060.01 CCS：C178 发布：2020-05-27 实施：2020-05-29

DIN EN 16487-2012 声学.吊顶试验规程.吸音作用.德文版本prEN 16487-2012
简介：
信息：ICS：91.060.30;91.120.20 CCS：P31 发布：2012-10 实施：

ASTM C1410-2005ae1 多孔三聚氰胺隔热和吸音的标准规范
简介：1.1 This specification covers the type, physical properties, and dimensions of open-cell melamine foam intended for use as thermal and sound-absorbing insulation for temperatures from x2212;40 to +350x00B0;F (x2212;40 to +177x00B0;C) in industrial environments. 1.2 Some uses of thermal insulation materials covered by this specification are governed by building codes that address fire performance. 1.3 The use of an appropriate vapor retarder is required on cold surface applications where water vapor condense and cause a decrease in thermal performance. Refer to Practice C755 for selection of vapor retarders. Facings shall be agreed upon between the purchaser and the manufacturer or supplier. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：91.100.60 (Thermal and sound insulating materials) CCS：发布：2005 实施：

DIN EN 1793-1-2017 道路交通减噪设备.测定声学性能的试验方法.第1部分:扩散声场条件下吸音作用的本质特征;德文版本EN 1793-1-2017
简介：
信息：ICS：17.140.30;93.080.30 CCS：P66 发布：2017-07 实施：

ASTM C635/C635M-2012 吸音瓦及铺设顶栅镶板用金属悬吊装置的生产、性能和试验的标准规范
简介：1.1 This specification covers metal ceiling suspension systems used primarily to support acoustical tile or acoustical lay-in panels. 1.2 Some suspension systems incorporate locking assembly details that enhance performance by providing some continuity or load transfer capability between adjacent sections of the ceiling grid. The test methods included in this specification do not provide the means for making a complete evaluation of continuous beam systems, nor for assessing the continuity contribution to overall system performance. However, the test methods can be used for evaluating primary structural members in conjunction with secondary members that interlock, as well as with those of noninterlocking type. 1.3 While this specification is applicable to the exterior installation of metal suspension systems, the atmospheric conditions and wind loading require additional design attention to ensure safe implementation. For that reason, a specific review and approval should be solicited from the responsible architect and engineer, or both, for any exterior application of metal suspension systems in the construction of a new building or building modification. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.5 The following safety hazards caveat pertains only to the test methods described in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：91.120.20 (Acoustics in buildings. Sound insulatio CCS：P32 发布：2012 实施：

ASTM C1410-2005a 多孔三聚氰胺隔热和吸音的标准规范
简介：1.1 This specification covers the type, physical properties, and dimensions of open-cell melamine foam intended for use as thermal and sound-absorbing insulation for temperatures from -40 to 350176F (-40 to 177176C) in industrial environments. 1.2 The use of thermal insulation materials covered by this specification may be governed by building codes that address fire performance. 1.3 The use of an appropriate vapor retarder is required on cold surface applications where water vapor could condense and cause a decrease in thermal performance. Refer to Practice C755 for selection of vapor retarders. Facings shall be agreed upon between the purchaser and the manufacturer or supplier. This specification addresses the foam alone. 1.4 The values stated in inch-pounds are to be regarded as the standard. The SI units given in parentheses are provided for information only and may be approximate. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：91.100.60 (Thermal and sound insulating materials) CCS：Q25 发布：2005 实施：

BS EN 1793-1-2017 道路交通减噪设备. 测定声学性能的试验方法. 扩散声场条件下吸音作用的本质特征
简介：
信息：ICS：17.140.30;93.080.30 CCS：Q85 发布：2017-04-30 实施：2017-04-30

KS F 5660-2011 聚酯纤维吸音隔热材料
简介：1이 표준은 건축용 또는 복합 패널의 단열 및 흡음재로 사용하는 폴리에스테르 흡음 단열재(
信息：ICS：91.100 CCS：Q25 发布：2011-10-07 实施：2011-10-07

KS M ISO 2509-2004 纯软木聚合膨胀吸音砖
简介：이 규격은 타일형 확장된 순수한 덩어리 형태의 흡음 코르크의 어떠한 특성을 규정한다.
信息：ICS：91.100.60;79.100 CCS：Q25 发布：2004-09-30 实施：2004-09-30

ASTM C1014-2017 喷施的矿物纤维吸热和吸音绝缘材料标准规格
简介：1.1x00a0;This specification covers the composition and the physical properties of spray-applied mineral fiber thermal and sound absorbing insulation. 1.2x00a0;These mineral fibers shall be pneumatically conveyed to a spray nozzle where they are mixed with water. These mineral fibers shall have a binder either pre-mixed with the fibers or added at the spray nozzle with the water. 1.3x00a0;The spray-applied mineral fiber insulation is intended for use in building constructions at ambient conditions. 1.4x00a0;This is a material specification only and is not intended to cover methods of application that are supplied by the manufacturer. 1.5x00a0;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：91.120.10 ; 91.120.20 CCS：Q25 发布：2017 实施：

NAVY QPL-24688 NOTICE 1-2011 多空聚酰亚胺泡沫吸音和吸热绝缘
简介：
信息：ICS： CCS：发布：2011 实施：

KS M ISO 2510-2004 软木吸音砖
简介：이 규격은 타일형 합성 절음 코르크의 어떤 특징을 규정한다.
信息：ICS：91.100.60 CCS：Q25 发布：2004-09-30 实施：2004-09-30

ASTM C635/C635M-2017 吸音砖和镶板天花板金属悬挂系统的制造, 性能和试验的标准规格
简介：1.1x00a0;This specification covers metal ceiling suspension systems used primarily to support acoustical tile or acoustical lay-in panels. 1.2x00a0;Some suspension systems incorporate locking assembly details that enhance performance by providing some continuity or load transfer capability between adjacent sections of the ceiling grid. The test methods of Test Methods E3090/E3090M referenced in this specification do not provide the means for making a complete evaluation of continuous beam systems, nor for assessing the continuity contribution to overall system performance. However, the test methods can be used for evaluating primary structural members in conjunction with secondary members that interlock, as well as with those of noninterlocking type. 1.3x00a0;While this specification is applicable to the exterior installation of metal suspension systems, the atmospheric conditions and wind loading require additional design attention to ensure safe implementation. For that reason, a specific review and approval should be solicited from the responsible architect and engineer, or both, for any exterior application of metal suspension systems in the construction of a new building or building modification. 1.4x00a0;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.5x00a0;The following safety hazards caveat pertains only to the test methods described in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6x00a0;This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
信息：ICS：91.120.20 CCS：P32 发布：2017 实施：

GOST 31705-2011 建筑物用吸因材料.吸音评估
简介：
信息：ICS：91.100.60 CCS：发布：2011 实施：2013-07-01

FZ/T 64057-2016 空调吸音用再加工纤维毡
简介：本标准规定了空调吸音用再加工纤维毡的技术要求、试验方法、检验规则、标志与包装、运输与贮存。本标准适用于空调吸音用再加工纤维毡。冰箱、冰柜等其他电器用再加工纤维毡可参照执行。
信息：ICS：59.080.30 CCS：W59 发布：2016-04-05 实施：2016-09-01

GOST 31704-2011 吸音材料.混音室中吸音测量方法
简介：
信息：ICS：91.100.60 CCS：发布：2011 实施：2013-07-01

ASTM C384-2004 用阻抗管法测定隔音材料的声阻抗与吸音性的标准试验方法
简介：The acoustical impedance properties of a sound absorptive material are related to its physical properties, such as airflow resistance, porosity, elasticity, and density. As such, the measurements described in this test method are useful in basic research and product development of sound absorptive materials. Normal incidence sound absorption coefficients are more useful than random incidence coefficients in certain situations. They are used, for example, to predict the effect of placing material in a small enclosed space, such as inside a machine. Estimates of the random incidence or statistical absorption coefficients for materials can be obtained from normal incidence impedance data. For materials that are locally reacting, that is, without sound propagation inside the material parallel to its surface, statistical absorption coefficients can be estimated from specific normal acoustic impedance values using an expression derived by London (1).5 Locally reacting materials include those with high internal losses parallel with the surface such as porous or fibrous materials of high density or materials that are backed by partitioned cavities such as a honeycomb core. Formulas for estimating random incidence sound absorption properties for both locally and bulk-reacting materials, as well as for multilayer systems with and without air spaces have also been developed (2).1.1 This test method covers the use of an impedance tube, alternatively called a standing wave apparatus, for the measurement of impedance ratios and the normal incidence sound absorption coefficients of acoustical materials.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.1.3 The values stated in SI units are to be regarded as the standard.
信息：ICS：91.120.20 (Acoustics in buildings. Sound insulatio CCS：发布：2004 实施：

LY/T 2559-2015 人造板吸音性能测定小混响室
简介：本标准规定了人造板吸音性能测定小混响室法的术语和定义、原理、设备、测试步骤和测试报告。本标准适用于对人造板吸音性能测定。
信息：ICS：79.060.01 CCS：B70 发布：2015-10-19 实施：2016-01-01

ASTM C1410-2010 蜂窝三聚氰胺吸热吸音隔音的标准规范
简介：1.1 This specification covers the type, physical properties, and dimensions of open-cell melamine foam intended for use as thermal and sound-absorbing insulation for temperatures from x2212;40 to +350x00B0;F (x2212;40 to +177x00B0;C) in industrial environments. 1.2 Some uses of thermal insulation materials covered by this specification are governed by building codes that address fire performance. 1.3 The use of an appropriate vapor retarder is required on cold surface applications where water vapor condense and cause a decrease in thermal performance. Refer to Practice C755 for selection of vapor retarders. Facings shall be agreed upon between the purchaser and the manufacturer or supplier. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：91.100.60 CCS：Q25 发布：2010 实施：

ASTM C635-2004 吸音瓦及铺设顶栅镶板用金属悬吊装置的生产、性能和试验的标准规范
简介：1.1 This specification covers metal ceiling suspension systems used primarily to support acoustical tile or acoustical lay-in panels.1.2 Some suspension systems incorporate locking assembly details that enhance performance by providing some continuity or load transfer capability between adjacent sections of the ceiling grid. The test methods included in this specification do not provide the means for making a complete evaluation of continuous beam systems, nor for assessing the continuity contribution to overall system performance. However, the test methods can be used for evaluating primary structural members in conjunction with secondary members that interlock, as well as with those of noninterlocking type.1.3 While this specification is applicable to the exterior installation of metal suspension systems, the atmospheric conditions and wind loading require additional design attention to ensure safe implementation. For that reason, a specific review and approval should be solicited from the responsible architect and engineer, or both, for any exterior application of metal suspension systems in the construction of a new building or building modification.1.4 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are provided for information purposes only.The following safety hazards caveat pertains only to the test methods described in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：91.120.20 (Acoustics in buildings. Sound insulatio CCS：P32 发布：2004 实施：

DIN EN 16487-2015 声学.吊顶试验规程.吸音作用.德文版本EN 16487-2014
简介：
信息：ICS：91.060.30;91.120.20 CCS：P31 发布：2015-02 实施：

KS L 9105-2009 岩棉吸音天棚板
简介：이 표준은 건축물 등에서 흡음을 목적으로 하여 주로 건축물의 천장에 사용하는 마감재인 미네
信息：ICS：91.060.30 CCS：Q25 发布：2009-09-04 实施：2009-09-04

ASTM C636-2004 吸音瓦及铺设顶棚镶板用金属天花板悬吊装置安装的标准实施规范
简介：1.1 This practice covers the installation of suspension systems for acoustical tile and lay-in panels. It is applicable to contractors whose services are utilized for installing acoustical ceilings and to other trades if their activities are responsible for interference with ceiling components or performance as defined in this recommended practice.1.2 While the practices described in this document have equal application to rated fire-resistive suspension systems, additional requirements may have been imposed to obtain the fire endurance classification of particular floor-ceiling or roof-ceiling assemblies. These details should be obtained from the manufacturers.1.3 Similarly, additional detailing may be necessary to meet sound attenuation requirements when ceiling plenums extend over contiguous rooms. These, too, should be obtained from the manufacturer of the acoustical material employed.1.4 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.1.5 While many of the practices described in this practice have application to the installation of metal suspension systems in exterior environments, the specific design of exterior ceiling installations requires the review and approval of the architect or engineer, or both, who are responsible for the construction of the building or modifications to an existing building. While recommendations from the manufacturer should be solicited, it remains the final responsibility of the architect/engineer to ensure proper application of the materials in question.This standard does not purport to address of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：91.120.20 (Acoustics in buildings. Sound insulatio CCS：P32 发布：2004 实施：

KS L 9105-2014 岩棉吸音天棚板
简介：이 표준은 건축물 등에서 흡음을 목적으로 하여 주로 건축물의 천장에 사용하는 마감재인 미네랄울흡음 천장판1)에 대하여 규정한다.
信息：ICS：91.060.30;91.100.20 CCS：Q25 发布：2014-04-07 实施：2014-04-07

ASTM C384-2004(2011) 用阻抗管法测定隔音材料的声阻抗与吸音性的标准试验方法
简介：The acoustical impedance properties of a sound absorptive material are related to its physical properties, such as airflow resistance, porosity, elasticity, and density. As such, the measurements described in this test method are useful in basic research and product development of sound absorptive materials. Normal incidence sound absorption coefficients are more useful than random incidence coefficients in certain situations. They are used, for example, to predict the effect of placing material in a small enclosed space, such as inside a machine. Estimates of the random incidence or statistical absorption coefficients for materials can be obtained from normal incidence impedance data. For materials that are locally reacting, that is, without sound propagation inside the material parallel to its surface, statistical absorption coefficients can be estimated from specific normal acoustic impedance values using an expression derived by London (1).5 Locally reacting materials include those with high internal losses parallel with the surface such as porous or fibrous materials of high density or materials that are backed by partitioned cavities such as a honeycomb core. Formulas for estimating random incidence sound absorption properties for both locally and bulk-reacting materials, as well as for multilayer systems with and without air spaces have also been developed (2).1.1 This test method covers the use of an impedance tube, alternatively called a standing wave apparatus, for the measurement of impedance ratios and the normal incidence sound absorption coefficients of acoustical materials.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.1.3 The values stated in SI units are to be regarded as the standard.
信息：ICS：91.120.20 (Acoustics in buildings. Sound insulatio CCS：Q25 发布：2004 实施：

KS L 9105-2014 岩棉吸音天棚板
简介：이 표준은 건축물 등에서 흡음을 목적으로 하여 주로 건축물의 천장에 사용하는 마감재인 미네랄울흡음 천장판1)에 대하여 규정한다.
信息：ICS：91.060.30;91.100.20 CCS：Q25 发布：2014-04-07 实施：2014/4/7

GOST 23499-2009 吸音和隔音建筑材料和产品.通用规范
简介：
信息：ICS：91.100.60 CCS：发布：2009 实施：2011-04-01

ASTM C384-2003 用阻抗管法测定隔音材料的声阻抗与吸音性的标准试验方法
简介：1.1 This test method covers the use of an impedance tube, alternatively called a standing wave apparatus, for the measurement of impedance ratios and the normal incidence sound absorption coefficients of acoustical materials.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.1.3 The values stated in SI units are to be regarded as the standard.
信息：ICS：91.120.20 (Acoustics in buildings. Sound insulatio CCS：Q25 发布：2003 实施：

ASTM C1139-2014 军事用途的玻璃纤维保温和吸音毯和板的标准规格
简介：1.1x00a0;This specification covers unfaced flexible fibrous glass blanket and faced board used for thermal and sound absorbing insulation at temperatures up to 450x00b0;F (232x00b0;C) for military applications as a replacement for MIL-I-22023D. 1.2x00a0;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3x00a0;This specification measures and describes the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions. 1.4x00a0;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5x00a0;The following hazard caveat pertains only to the test method section of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：91.120.10 (Thermal insulation of buildings); 91.12 CCS：发布：2014 实施：

ASTM C1014-2003 喷施的矿物纤维吸热和吸音绝缘材料标准规范
简介：1.1 This specification covers the composition and the physical properties of spray-applied mineral fiber thermal and sound absorbing insulation.1.2 These mineral fibers shall be pneumatically conveyed to a spray nozzle where they are mixed with water. These mineral fibers shall have a binder either pre-mixed with the fibers or added at the spray nozzle with the water.1.3 The spray-applied mineral fiber insulation is intended for use in building constructions at ambient conditions.1.4 This is a material specification only and is not intended to cover methods of application that are supplied by the manufacturer.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：91.120.10 (Thermal insulation of buildings); 91.12 CCS：Q25 发布：2003 实施：

ASTM C1014-2008 喷施的矿物纤维吸热和吸音绝缘材料标准规范
简介：1.1 This specification covers the composition and the physical properties of spray-applied mineral fiber thermal and sound absorbing insulation. 1.2 These mineral fibers shall be pneumatically conveyed to a spray nozzle where they are mixed with water. These mineral fibers shall have a binder either pre-mixed with the fibers or added at the spray nozzle with the water. 1.3 The spray-applied mineral fiber insulation is intended for use in building constructions at ambient conditions. 1.4 This is a material specification only and is not intended to cover methods of application that are supplied by the manufacturer. 1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：91.120.20 (Acoustics in buildings. Sound insulatio CCS：Q25 发布：2008 实施：

ASTM C1014-2003e1 喷施的矿物纤维吸热和吸音绝缘材料标准规范
简介：1.1 This specification covers the composition and the physical properties of spray-applied mineral fiber thermal and sound absorbing insulation.1.2 These mineral fibers shall be pneumatically conveyed to a spray nozzle where they are mixed with water. These mineral fibers shall have a binder either pre-mixed with the fibers or added at the spray nozzle with the water.1.3 The spray-applied mineral fiber insulation is intended for use in building constructions at ambient conditions.1.4 This is a material specification only and is not intended to cover methods of application that are supplied by the manufacturer.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：91.120.10 (Thermal insulation of buildings); 91.12 CCS：Q25 发布：2003 实施：