中心实验室和分实验室检测标准中心实验室和分实验室-中析研究所检测

(CMA)

(CNAS)

(ISO)

(高新技术企业)

中心实验室和分实验室相关标准参考信息

ASTM E1096-86(2018) 实验室玻璃分液漏斗的标准规范
简介：
信息：ICS：71.040.20 CCS：发布：2018-01-01 实施：

ASTM D1796-1997 离心法测定燃料油中水分及沉淀物的标准试验方法(实验室法)
简介：1.1 This test method covers the laboratory test for determination of water and sediment in fuel oils by using the centrifuge method in the range from 0 to 30% volume. This chapter, along with API Chapter 10.3 (Test Method D 4007, IP 359), supersedes the previous edition of ASTM Test Method D 1796 (API Standard D 2548, IP75). Note 1-With some types of fuel oils such as residual fuel oils or distillate fuel oils containing residual components, it is difficult to obtain water or sediment contents with this test method. When this situation is encountered, Method D 95 (API MPMS Chapter 10.5) or Test Method D 473 (API MPMS Chapter 10.1) may be used. 1.2 annex A2 contains a procedure for saturating toluene with water. 1.3 the values stated in SI units are to be regarded as the standard. The values in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For a specific precautionary statement see 5.1.
信息：ICS： CCS：E31 发布：1997 实施：

ISO 4800-1977 实验室玻璃器皿.分液漏斗和滴液漏斗
简介：
信息：ICS：0433 CCS：N64 发布：1977-12 实施：

CFR 10-26.159-2014 能源. 第26部分:值班计划健身. 第G子部分:由卫生和人类服务部认证的实验室. 第26.159节:保证标本的安全，监管链,并保存.
简介：(a) The HHS-certified laboratories performing services for licensees and other entities under this part shall be secure at all times. Each laboratory shall have in place sufficient security measures to control access to the premises and to ensure that no unauthorized personnel handle specimens or gain access to the laboratory processes or areas where records are stored. Access to these secured areas must be limited to specially authorized individuals whose authorization is documented. All authorized visitors, and maintenance and service personnel, shall be escorted at all times in the laboratory, except personnel who are authorized to conduct inspections and audits on behalf of licensees, other entities, the NRC, or the HHS Secretary, and emergency personnel (including but not limited to firefighters and medical rescue teams).
信息：ICS： CCS：F00 发布：2014-11-10 实施：2014-11-10

ASTM D1796-1997e1 离心法测定燃料油中水分及沉淀物的标准试验方法(实验室法)
简介：1.1 This test method covers the laboratory test for determination of water and sediment in fuel oils by using the centrifuge method in the range from 0 to 30 % volume. This chapter, along with API MPMS Chapter 10.3 (Test Method D 4007), supersedes the previous edition of Test Method D 1796 (API Standard D 2548, IP 75). Note 18212;With some types of fuel oils such as residual fuel oils or distillate fuel oils containing residual components, it is difficult to obtain water or sediment contents with this test method. When this situation is encountered, Test Method D 95 (API MPMS Chapter 10.5) or Test Method D 473 (API MPMS Chapter 10.1) may be used.1.2 contains a procedure for saturating toluene with water.1.3 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For a specific precautionary statement see 6.1.
信息：ICS： CCS：E31 发布：1997 实施：

MNOSZ 21325-1955 实验室玻璃器皿，带打磨塞子的圆柱形分液漏斗
简介：
信息：ICS： CCS：发布：1955-01-01 实施：

KS L ISO 4800-2012 实验室玻璃器皿.分液漏斗和滴液漏斗
简介：이 표준은 국제적으로 통용되는 일반 실험실용 분액 깔때기와 적하 깔때기에 대하여 규정한다.
信息：ICS：71.040.20 CCS：Q07 发布：2012-11-30 实施：2012-11-30

QB/T 2110-1995 实验室玻璃仪器.分液漏斗和滴液漏斗
简介：本标准规定了实验室用玻璃分液漏斗和滴液漏斗的产品分类、技术要求、试验方法、检验规则及标志、包装、运输、贮存等。本标准适用于实验室中对两种比重不同且不相溶的液体进行分离的分液漏斗和用于将试剂溶液加人到反应容器中的滴液漏斗。
信息：ICS： CCS：N64 发布：1995-06-07 实施：1996-03-01

MNOSZ 21326-1955 实验室玻璃器皿，带液滴计量装置和打磨塞子的圆柱形分液漏斗
简介：
信息：ICS： CCS：发布：1955-01-01 实施：

KS L ISO 4800-2012(2017) 实验室玻璃器皿分液漏斗和滴液漏斗
简介：
信息：ICS：71.040.20 CCS：发布：2012-11-30 实施：

NEN-EN 20-1-1992 木材防腐剂-对褐粉蠹（斯帝温）预防（镶木地板-野猪）措施的规定．第一部分：通过表面处理方法（实验室方法）实施
简介：This Part of EN 20 specifies a method far the determinaticn of the protective effectiveness ar the taxie values of a wood preservative against infestatlcn by Lyctus brunneus (Stephens) when the product Is applied as a surfaoe treatment to wood.This method Is applicable to :- water-insoluble Chemicals which are being studied as active insecticides, ar,- arganic fornulations, as supplied ar as prepared in the labaratary by dilution of concentratjes, ar,- organic water-dispersible fontulaticns as supplied ar as prepared in the laboratnry fay dilution of aonosntrates, ar- water-soluble materials, for example salts.NOTE : Thls method may be used in oonjunction with ageing proosdures, which do not remove the atided nutri?nt.
信息：ICS： CCS：发布：1992-12 实施：

UNI 2749-1945 化学实验室用玻璃制品．重分料漏斗
简介：
信息：ICS： CCS：发布：1945-08-01 实施：

DZ/T 0013-1991 实验室用旋转式试样缩分器
简介：本标准规定了旋转式试样缩分器的基本结构型式、主要技术参数、型号编制方法、技术要求、试验方法、检验规则及标志、包装等要求。本标准适用于地质、冶金、有色金属、煤炭、建材、化工等生产、科研部门实验室对干燥试样粒度小于3mm进行缩分的旋转式试样缩分器(以下简称“缩分器”)。
信息：ICS：71.040.10 CCS：N61 发布：1991-12-09 实施：1992-07-01

UNI 2748-1945 化学实验室用玻璃制品．轻分料漏斗
简介：
信息：ICS： CCS：发布：1945-08-01 实施：

CFR 10-430.25-2014 能源. 第430部分:消费品节能计划. 第B子部分:试验程序. 第430.25节:实验室认可计划.
简介：Testing for fluorescent lamp ballasts performed in accordance with appendix Q1 to this subpart shall comply with this §430.25. The testing for general service fluorescent lamps, general service incandescent lamps, and incandescent reflector lamps shall be performed in accordance with Appendix R to this subpart. The testing for medium base compact fluorescent lamps shall be performed in accordance with Appendix W of this subpart. This testing, with the exception of lifetime testing of general service incandescent lamps, shall be conducted by test laboratories accredited by the National Voluntary Laboratory Accreditation Program (NVLAP) or by an accrediting organization recognized by NVLAP. NVLAP is a program of the National Institute of Standards and Technology, U.S. Department of Commerce. NVLAP standards for accreditation of laboratoriesthat test for compliance with standards for fluorescent lamp ballast luminous efficiency (BLE), lamp efficacy, lamp lifetime, and fluorescent lamp CRI are set forth in 15 CFR part 285. A manufacturer’s or importer’s own laboratory, if accredited, may conduct the applicable testing. Testing for BLE may also be conducted by laboratories accredited by Underwriters Laboratories or Council of Canada. Testing for fluorescent lamp ballasts performed in accordance with Appendix Q to this subpart is not required to be conducted by test laboratories accredited by NVLAP or an accrediting organization recognized by NVLAP.
信息：ICS： CCS：F04 发布：2012-01-27 实施：2012-01-27

GOST 29252-1991 实验室用玻璃器皿.第二部分.无等待时间的滴定管
简介：
信息：ICS：71.040.20 CCS：发布：1991 实施：1994-01-01

简介： 信息：

ASTM E1096-86(2011) 实验室玻璃分液漏斗的标准规范
简介：
信息：ICS：71.040.20 CCS：发布：2011-12-01 实施：

GOST 29227-1991 实验室用玻璃器皿.刻度移液管.第一部分.一般要求
简介：Настоящий стандарт устанавливает требования к лабораторным градуированным пипеткам общего назначения
信息：ICS：71.040.20 CCS：发布：1991 实施：1994-01-01

简介： 信息：

ASTM D1796-2011e1 使用离心法测定燃料油中水分及沉淀物的标准试验方法(实验室规程)
简介：4.1x00a0;The water and sediment content of fuel oil is significant because it can cause corrosion of equipment and problems in processing. A determination of water and sediment content is required to measure accurately net volumes of actual fuel oil in sales, taxation, exchanges, and custody transfers. 4.2x00a0;This test method may not be suitable for products that contain alcohols that are soluble in water. In cases where the impact on the results may be significant, the user is advised to consider using another test method, such as Test Method D6304. 1.1x00a0;This test method describes the laboratory determination of water and sediment in fuel oils in the range from 0 to 308201;% volume by means of the centrifuge procedure.Note 1x2014;With some types of fuel oils such as residual fuel oils or distillate fuel oils containing residual components, it is difficult to obtain water or sediment contents with this test method. When this situation is encountered, Test Method D95 (API MPMS Chapter 10.5) or Test Method D473 (API MPMS Chapter 10.1) may be used.Note 2x2014;API MPMS Chapter 10.6 (Test Method D1796) along with API MPMS Chapter 10.3 (Test Method D4007) formerly superseded API Standard 2548. 1.2x00a0;The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For a specific precautionary statement, see 6.1.
信息：ICS：75.160.20 (Liquid fuels) CCS：E31 发布：2011 实施：

GOST 29251-1991 实验室用玻璃器皿.滴定管.第一部分.一般要求
简介：
信息：ICS：71.040.20 CCS：发布：1991 实施：1994-01-01

简介： 信息：

ASTM D1796-2011 离心法测定燃料油中水分及沉淀物的标准试验方法(实验室法)
简介：The water and sediment content of fuel oil is significant because it can cause corrosion of equipment and problems in processing. A determination of water and sediment content is required to measure accurately net volumes of actual fuel oil in sales, taxation, exchanges, and custody transfers. This test method may not be suitable for products that contain alcohols that are soluble in water. In cases where the impact on the results may be significant, the user is advised to consider using another test method, such as Test Method D6304.1.1 This test method describes the laboratory determination of water and sediment in fuel oils in the range from 0 to 30 % volume by means of the centrifuge procedure. Note 18212;With some types of fuel oils such as residual fuel oils or distillate fuel oils containing residual components, it is difficult to obtain water or sediment contents with this test method. When this situation is encountered, Test Method D95 (API MPMS Chapter 10.5) or Test Method D473 (API MPMS Chapter 10.1) may be used. Note 28212;API MPMS Chapter 10.6 (Test Method D1796) along with API MPMS Chapter 10.3 (Test Method D4007) formerly superseded API Standard 2548. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For a specific precautionary statement, see 6.1.
信息：ICS：75.160.20 (Liquid fuels) CCS：E31 发布：2011 实施：

DOD A-A-54080-1990 微型分血器实验室离心分离机
简介：This commercial item description covers one type of high-speed centrifuge with direct reading capabilities, suitable for use in the micro method of determining hematocrits.
信息：ICS：49.020 CCS：C36 发布：1990-01-30 实施：

简介： 信息：

GOST R ISO 1146-2009 实验室用高温测量分锥.规范
简介：
信息：ICS：81.080 CCS：发布：2009 实施：2010-06-01

JUS B.E4.101-1988 实验室玻璃器皿及其附件．球形分液漏斗
简介：
信息：ICS： CCS：发布：1988-01-01 实施：

简介： 信息：

GOST R ISO 1146-2009 实验室用高温测量分锥.规范
简介：
信息：ICS：81.080 CCS：发布：2009 实施：2010-06-01

DOD A-A-51351-1986 电池微型分血器实验室离心分离机
简介：The General Services AdnIinistra.tion bas authorized the use of this commercial item description.
信息：ICS：49.020 CCS：C36 发布：1986-02-28 实施：

简介： 信息：

ASTM E1096-86(2006) 实验室玻璃分液漏斗的标准规范
简介：
信息：ICS：71.040.20 CCS：发布：2006-11-01 实施：

ASTM E1096-86(1996) 实验室玻璃分液漏斗的标准规范
简介：
信息：ICS： CCS：发布：1986-01-31 实施：

简介： 信息：

AS 2407-2005 实验室玻璃器皿．分液漏斗和滴液漏斗
简介：
信息：ICS：71.040.20 CCS：发布：2005-12-23 实施：

ASTM E1096-86(2001)e1 实验室玻璃分液漏斗的标准规范
简介：
信息：ICS：71.040.20 CCS：发布：1986-01-31 实施：

简介： 信息：

ASTM D1796-2004(2009) 离心法测定燃料油中水分及沉淀物的标准试验方法(实验室规程)
简介：The water and sediment content of fuel oil is significant because it can cause corrosion of equipment and problems in processing. A determination of water and sediment content is required to measure accurately net volumes of actual fuel oil in sales, taxation, exchanges, and custody transfers.1.1 This test method describes the laboratory determination of water and sediment in fuel oils in the range from 0 to 30 % volume by means of the centrifuge procedure. Note 18212;With some types of fuel oils such as residual fuel oils or distillate fuel oils containing residual components, it is difficult to obtain water or sediment contents with this test method. When this situation is encountered, Test Method D 95 (API MPMS Chapter 10.5) or Test Method D 473 (API MPMS Chapter 10.1) may be used. Note 28212;API MPMS Chapter 10.6 (Test Method D 1796) along with API MPMS Chapter 10.3 (Test Method D 4007) formerly superseded API Standard 2548. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For a specific precautionary statement, see 6.1.
信息：ICS：75.160.20 (Liquid fuels) CCS：E31 发布：2004 实施：

ASTM E1096-1986(2006) 实验室玻璃分液漏斗
简介：1.1 This specification provides standard dimensional requirements for glass separatory funnels for general laboratory use.
信息：ICS：71.040.20 (Laboratory ware and related apparatus) CCS：N64 发布：1986 实施：

简介： 信息：

ASTM D1796-2004 离心法测定燃料油中水分及沉淀物的标准试验方法(实验室法)
简介：The water and sediment content of fuel oil is significant because it can cause corrosion of equipment and problems in processing. A determination of water and sediment content is required to measure accurately net volumes of actual fuel oil in sales, taxation, exchanges, and custody transfers.1.1 This test method describes the laboratory determination of water and sediment in fuel oils in the range from 0 to 30 % volume by means of the centrifuge procedure.Note 1With some types of fuel oils such as residual fuel oils or distillate fuel oils containing residual components, it is difficult to obtain water or sediment contents with this test method. When this situation is encountered, Test Method D 95 (API MPMS Chapter 10.5) or Test Method D 473 (API MPMS Chapter 10.1) may be used.Note 2API MPMS Chapter 10.6 (Test Method D 1796) along with API MPMS Chapter 10.3 (Test Method D 4007) formerly superseded API Standard 2548.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For a specific precautionary statement, see .
信息：ICS：75.160.20 (Liquid fuels) CCS：E31 发布：2004 实施：

ASTM E1096-1986(1996) 实验室玻璃分液漏斗
简介：1.1 This specification provides standard dimensional requirements for glass separatory funnels for general laboratory use.
信息：ICS： CCS：N64 发布：1986 实施：

简介： 信息：

DIN ISO 4800-2002 实验室玻璃器皿.分液漏斗和滴液漏斗
简介：The document specifies requirements, materials and dimensions for separating and dropping funnels for general laboratory use. Separating funnels are used for liquid/liquid extractions. Dropping funnels are used for adding of reagent solutions to reaction vessels.,,
信息：ICS：71.040.20 CCS：N64 发布：2002-08 实施：

ASTM E1096-1986(2001)e1 实验室玻璃分液漏斗
简介：1.1 This specification provides standard dimensional requirements for glass separatory funnels for general laboratory use.
信息：ICS：71.040.20 (Laboratory ware and related apparatus) CCS：N64 发布：1986 实施：

简介： 信息：

TCVN 7158-2002 实验室玻璃器皿.分液漏斗和滴液漏斗
简介：
信息：ICS： CCS：发布：2002 实施：

ASTM E1096-1986(2011) 实验室玻璃分液漏斗的标准规格
简介：1.1 This specification provides standard dimensional requirements for glass separatory funnels for general laboratory use.
信息：ICS：71.040.20 (Laboratory ware and related apparatus) CCS：N64 发布：1986 实施：

简介： 信息：

SANS 4800-1998 实验室玻璃仪器．分液漏斗和滴液漏斗
简介：Specifies details of an internationally acceptable series of glass separating funnels and dropping funnels suitable for general use in laboratories.
信息：ICS：71.040.20 CCS：N64 发布：2001-05-21 实施：

ASTM E1096-1986(2018) 实验室玻璃分液漏斗的标准规格
简介：1.1x00a0;This specification provides standard dimensional requirements for glass separatory funnels for general laboratory use. 1.2x00a0;This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
信息：ICS：71.040.20 CCS：N64 发布：1986 实施：

简介： 信息：

BS ISO 4800-1998 实验室玻璃器皿.分液漏斗和滴液漏斗
简介：This International Standard specifies details of an internationally acceptable series of glass separating funnels and dropping funnels suitable for general use in laboratories.
信息：ICS：71.040.20 CCS：N64 发布：1999-04-15 实施：1999-04-15

NF B35-018-1983 实验室用玻璃器皿.分液漏斗和滴液漏斗
简介：
信息：ICS：71.040.20 CCS：N64 发布：1983-07-01 实施：1983-07-21

简介： 信息：

ISO 4800-1998 实验室玻璃器皿分液漏斗和滴液漏斗
简介：This International Standard specifies details of an internationally acceptable series of glass separating funnels and dropping funnels suitable for general use in laboratories.
信息：ICS：71.040.20 CCS：N64 发布：1998-12 实施：

CNS 6513-1980 实验室用玻璃分液漏斗与滴液漏斗
简介：本标准适用于国际适用型类之实验室用玻璃分液漏斗与滴漏斗。
信息：ICS：71.040.20 CCS：发布：1980-09-30 实施：1980-09-30

简介： 信息：