凝胶渗透色谱检测标准凝胶渗透色谱-中析研究所检测

(CMA)

(CNAS)

(ISO)

(高新技术企业)

凝胶渗透色谱相关标准参考信息

GB/T 30787-2014 数字印刷材料用成膜树脂平均分子量及其分布的测定凝胶渗透色谱法
简介：本标准规定了用凝胶渗透色谱测定数字印刷材料用成膜树脂分子量及其分布的方法。本标准适用于由苯酚、甲酚、二酚或其中的两种或者三种混酚与甲醛反应制得的成膜树脂。适用的平均重均分子量范围在2 000~40 000、数据分子量在500~5 000、分布系数在4.0~8.0。
信息：ICS：37.040.20 CCS：G80 发布：2014-07-08 实施：2014-12-01

DIN 55672-2-2016 凝胶渗透色谱法(GPC).第2部分:用N,N-二甲基乙酰胺(DMAC)作洗脱溶剂
简介：
信息：ICS：71.040.50 CCS：G63 发布：2016-03 实施：

DIN 55672-3-2007 凝胶渗透色谱法(GPC).第3部分:用水作洗脱溶剂
简介：This standard describes the determination of the molecular weight distribution, number-average molecularweight Mn and weight-average molecular weight Mw of polymers that are soluble in water by gel permeationchromatography (GPC).This standard is applicable to neutral polymers and polyanions (e.g. polycarboxylates, polysaccharides,completely saponified polyvinyl alcohols and high-molecular polyethylene oxides). It is not applicable topolycations (e.g. polyvinytpyrrolidone, polyvinylpyridine, salts of poly(diallyI-N,N-dimethyl-azacyclopentane)and chitosane.It is possible that, in spite of the good solubility in the mobile phase and the good repeatability of thechromatograms obtained, this method cannot be used with certain polymer types because of specificinteractions, such as adsorption, within the sample/eluent/column combination (see also clause 12).The method is not an absolute one and requires calibration with commercially available unbranched pullulanstandards that have been characterized by independent absolute methods. The results for samples ofpolymers other than pullulan are therefore only comparable within groups of samples of the same type.The conditions specified in this standard are not suitable for the GPC analysis of polymer samples with Mwvalues greater than 10~6 g/mol (see Annex C).No correction methods (e.g. for the elimination of peak broadening) are included in this standard. If absolutemolecular weight values are required, an absolute method, e.g. membrane osmometry for Mn or lightscattering for Mw, shall be used.
信息：ICS：71.040.50 CCS：G04 发布：2007-08 实施：

GB/T 27843-2011 化学品.聚合物低分子量组分含量测定.凝胶渗透色谱法（GPC）
简介：本标准规定了使用凝胶渗透色谱法(gelpermeationchromatography,GPC)测定聚合物低分子量组分含量的方法。本标准适用于测定聚合物低分子量组分的含量。由于聚合物材料性质多样,所含低分子量物质也不同,一些聚合物因具有特殊复杂结构而不适于使用凝胶色谱法来测定低分子量含量,可以采用其他方法测定,测定时根据聚合物材料的详细资料,选择相应的仪器测定。
信息：ICS：13.300 CCS：A80 发布：2011-12-30 实施：2012-08-01

DIN 55672-3-2016 凝胶渗透色谱法(GPC).第3部分:用水作洗脱溶剂
简介：
信息：ICS：71.040.50 CCS：G04 发布：2016-03 实施：

KS M ISO 11344-2007 合成生橡胶.凝胶渗透色谱法测定溶液聚合物分子质量的分布
简介：이 규격은 분자 질량 범위가 5×103∼1×106이고 테트라히드로퓨란(THF)에 완전히 용
信息：ICS：83.040.10 CCS：G34 发布：2007-06-29 实施：2007-06-29

GB/T 27810-2011 色漆和清漆用漆基.凝胶渗透色谱法（GPC）.用四氢呋喃做洗脱剂
简介：警示—本标准可能涉及危险的物质、操作及设备。本标准无意论及与其使用有关的（如果有的话）所有安全问题，因此本标准的使用者有责任制定合适的安全和健康措施并保证符合国家的任何法规的规定。具体的危害陈述见第6章。本标准规定了用凝胶渗透色谱法（GPC)测定溶解于THF(四氢呋喃）中的聚合物的分子量分布、数均分子量M和重均分子量M的方法。即使用本方法能获得良好的重复性，本方法也不能用于发生了特殊的相互作用的某些聚合物，例如在样品/洗脱剂/色谱柱体系间发生了吸附作用。本方法不是一种绝对的测定方法，需要用市售的无支链聚苯乙烯标准物质进行标定，而这种标准物质已用绝对方法测得其分子量。因此除聚苯乙烯外，聚合物样品的测定结果仅用于相同类型样品组间的比较。本标准规定的条件不适用于用GPC分析M数值大于10的聚合物样品（见附录C)。本标准无修正方法，例如消除峰加宽。如果要得到绝对分子量数值，需要使用绝对方法测量，例如用膜渗透法测定M或光散射法测定M。
信息：ICS：87.040 CCS：G50 发布：2011-12-30 实施：2012-06-01

SN/T 4183-2015 聚烯烃相对分子量和分子量分布的测定高温凝胶渗透色谱法
简介：本标准规定了聚乙烯和聚丙烯的相对分子量和分子量分布的凝胶渗透色谱测定方法。本标准适用于聚乙烯和聚丙烯的相对分子量和分子量分布的测定。本标准不适用于高压低密度聚乙烯的相对分子量和分子量分布的测定。
信息：ICS： CCS：发布：2015-05-26 实施：2016-01-01

GB/T 21863-2008 凝胶渗透色谱法(GPC).用四氢呋喃做淋洗液
简介：本标准规定了凝胶渗透色谱法(GPC)测定在四氢呋喃(THF)中溶解的聚合物的分子量分布、数均分子量M和重均分子量M的方法和试验条件。如果试样/洗脱剂/分离材料系统中发生特殊的相互作用(例如吸收)，即使单个聚合物得到色谱分离且有良好的可重复性也不适用本方法。凝胶渗透色谱(GPC)是相对测定方法，需要用市售线性、使用绝对方法已知分子量的聚苯乙烯标准物质进行校正。其结果对于具有不同结构的聚合物试样仅可以作为相同结构试样组的参考值。本标准不适用于测定M大于10g/mol的聚合物(见附录C)。本标准无法实施校正方法(如消除峰值扩散)。如果需要测定绝对摩尔质量，则应使用绝对方法(例如：用于测定M的膜渗压法，或者M的光散射法)。
信息：ICS：13.300 CCS：G04 发布：2008-05-12 实施：2008-09-01

GOST 33418-2015 环境危害化学品试验. 采用凝胶渗透色谱法测定聚合物的数均分子量和分子量分布
简介：
信息：ICS：13.020.01 CCS：发布：2015 实施：2016-09-01

ASTM D6474-99(2006) 通过高温凝胶渗透色谱法测定聚烯烃的分子量分布和分子量平均值的标准测试方法
简介：
信息：ICS：83.080.20 CCS：发布：2006-03-15 实施：

KS M ISO 13885-1-2022 凝胶渗透色谱法（GPC）.第1部分:四氢呋喃（THF）作为洗脱剂
简介：
信息：ICS：87.060.20 CCS：发布：2022-12-13 实施：

GOST 33402-2015 环境危害化学品试验. 采用凝胶渗透色谱法测定聚合物的低分子量含量
简介：
信息：ICS：13.020.01 CCS：发布：2015 实施：2016-09-01

NF V03-094-2-2004 无脂食品.苯并咪唑杀菌剂carbendazim、噻唑苯并咪唑和苯菌灵(类carbendazim)的测定.第2部分:凝胶渗透色谱净化HPLC法
简介：
信息：ICS：67.080.01 CCS：X04 发布：2004-12-01 实施：2004-12-20

T/TDSTIA 026-2022 婴幼儿配方乳粉中α-乳白蛋白、β-乳球蛋白的测定凝胶渗透色谱法
简介：本标准为首次制定，方法原理为婴幼儿配方乳粉试样溶液调节至pH4.60，使酪蛋白和变性的乳清蛋白沉淀，而未变性的α-乳白蛋白和β-乳球蛋白仍保留在溶液中。向溶液中加入盐酸胍，以盐酸胍为变性剂，以β-巯基乙醇为还原剂，断开蛋白质中的硫-硫（S-S）化学键，形成展开的α-乳白蛋白和β-乳球蛋白的单体结构。经凝胶色谱柱分离，紫外光检测，外标法定量。
信息：ICS：67.100.99 CCS：C144 发布：2022-11-21 实施：2022-11-21

GOST 33418-2015 环境危害化学品试验. 采用凝胶渗透色谱法测定聚合物的数均分子量和分子量分布
简介：
信息：ICS：13.020.01 CCS：Z12 发布：2015 实施：2016-09-01

BS EN 14333-2-2004 无脂食品.苯并咪唑杀真菌剂carbendazim、噻唑苯并咪唑和苯菌灵(类似carbendazim).凝胶渗透色谱净化的HPLC法
简介：This document specifies a high performance liquid chromatographic method for the determination of the benzimidazole fungicides carbendazim and thiabendazole in fruits, vegetables and processed products.When benomyl is present, it is completely degraded to carbendazim and is also determined as carbendazim. Thiophanate-methyl is partly decomposed and therefore not quantitatively determined.The method has been validated for carbendazim and thiabendazole in an interlaboratory test with homogenates of apples, French beans, mushrooms, lemons and fruit based infant food.
信息：ICS：67.080.01 CCS：X04 发布：2004-10-15 实施：2004-10-15

T/CECS 10189-2022 混凝土减水剂分子量测试凝胶渗透色谱法
简介：本文件规定了测试混凝土减水剂分子量的凝胶渗透色谱法的术语和定义、方法原理、试剂和材料、仪器和设备、试验步骤、试验数据处理、报告。
信息：ICS：91.010.01 CCS：E4710 发布：2022-04-29 实施：2022-06-12

GOST 33402-2015 环境危害化学品试验. 采用凝胶渗透色谱法测定聚合物的低分子量含量
简介：
信息：ICS：13.020.01 CCS：Z12 发布：2015 实施：2016-09-01

ISO 11344-2004 合成生橡胶.用凝胶渗透色谱法测定溶液聚合物分子质量的分布
简介：This International Standard describes a method for the determination of the molecular mass, expressed as polystyrene, and the molecular-mass distribution of polymers produced in solution which are completely soluble in tetrahydrofuran (THF) and which have a molecular-mass range from 5 × 10 to 1 × 10.It is not the purpose of this International Standard to explain the theory of gel permeation chromatography.
信息：ICS：83.040.10 CCS：G34 发布：2004-04 实施：

T/CECS 10189-2022 混凝土减水剂分子量测试凝胶渗透色谱法
简介：
信息：ICS：91.010.01 CCS：CCSQ13 发布：2022-04-29 实施：2022-09-01

KS M ISO 13885-1-2012 涂料和清漆用胶粘剂.凝胶渗透色谱法(GPC).第1部分:用四氢呋喃作洗脱溶剂
简介：이 표준은 겔 투과 크로마토그래피(GPC)1)로 THF(테트라하이드로퓨란)에 용해성이 있는
信息：ICS：87.060.20 CCS：G51 发布：2012-12-18 实施：2012-12-18

ASTM D6474-99 通过高温凝胶渗透色谱法测定聚烯烃的分子量分布和分子量平均值的标准测试方法
简介：
信息：ICS：83.080.20 CCS：发布：1999-11-10 实施：

ISO 13885-1:2020 凝胶渗透色谱法（GPC）第1部分:四氢呋喃（THF）作为洗脱剂
简介：
信息：ICS：87.060.20 CCS：发布：2020-07-08 实施：

KS M ISO 13885-1-2012(2017) 色漆和清漆用粘合剂凝胶渗透色谱法第1部分:四氢呋喃洗脱液
简介：
信息：ICS：87.060.20 CCS：发布：2012-12-18 实施：

BS 6782-14-1999 涂料粘合剂.用氢呋喃作为洗脱剂的凝胶渗透色谱法（GPC)
简介：This part of ISO 13885 is one of a series of standards dealing with the sampling and testing of paints, varnishes and related products.It describes conditions for the determination of the molecular-mass distribution, number-average molecular mass Mn and mass-average molecular mass Mw of polymers that are soluble in THF (tetrahydrofuran) by gel permeation chromatography (GPC).It is possible that, in spite of the good repeatability obtained with this method, it cannot be used with certain polymer types because of specific interactions, such as adsorption within the sample/eluent/column system.The method is not an absolute one and requires calibration with commercially available unbranched-polystyrene standards that have been characterized by absolute methods. The results for samples of polymers other than polystyrene are therefore only comparable within groups of samples of the same type.The conditions specified in this part of ISO 13885 are not suitable for the GPC analysis of polymer samples with Mw values greater than 10 (see annex A).No correction methods, e.g. for the elimination of peak broadening, are included in this part of ISO 13885. If absolute molecular-mass values are required, an absolute method, e.g. membrane osmometry for Mn or light scattering for Mw, must be used.note:1) Also known as size exclusion chromatography (SEC).
信息：ICS：87.060.20 CCS：G38 发布：1999-03-15 实施：1999-03-15

ISO 13885-1-2020 凝胶渗透色谱法（GPC）第1部分:四氢呋喃（THF）作为洗脱剂
简介：
信息：ICS：87.060.20 CCS：发布：2020-07-08 实施：

ASTM D6474-12 通过高温凝胶渗透色谱法测定聚烯烃的分子量分布和分子量平均值的标准测试方法
简介：
信息：ICS：83.080.20 CCS：发布：2012-12-15 实施：

ASTM D6474-1999 高温凝胶渗透色谱法测定聚烯烃分子量分布和平均分子量的标准试验方法
简介：1.1 This test method covers the determination of molecular weight distributions and molecular weight averages of linear polyolefins by high temperature gel permeation chromatography (GPC). This test method uses commercially available polystyrene standards and equipment and is applicable to polyethylenes (excluding high pressre low density polyethylene-LDPE) and polypropylenes soluble in 1,2,4-trichlorobenzene (TCB) at 140176C. This test method is not absolute and requires calibration. Note 1--Size exclusion chromatography (SEC) often is used as an alternative name for gel permeation chromatography (GPC). Note 2--Specific methods and capabilities of users may vary with differences in columns, instrumentation, applications, software, and practices between laboratories. Note 3--One general method is outlined herein; alternative analytical practices can be followed and are attached in notes where appropriate. Note 4--There is no similar or equivalent ISO standard. 1.2 The values stated in SI units, based on IEEE/ASTM SI-10, are to be regarded as the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：83.080.20 (Thermoplastic materials) CCS：G04 发布：1999 实施：

ISO 13885-2:2020 凝胶渗透色谱法（GPC）第2部分:N N-二甲酰乙酰胺（DMAC）作为洗脱剂
简介：
信息：ICS：87.060.20 CCS：发布：2020-07-08 实施：

ASTM D6474-2012 用高温凝胶渗透色谱法测定聚烯烃分子量分布和平均分子量的标准试验方法
简介：5. Significance and UseTop Bottom 5.1 This test method measures the molecular weight distribution and molecular weight averages of polyethylene (except LDPE) and polypropylene resins. Differences in molecular weight and molecular weight distribution significantly affect physical properties, such as morphology, strength, melt flow etc., and as a result, the final properties of products made from these resins. 1.1 This test method covers the determination of molecular weight distributions and molecular weight averages of linear polyolefins by high temperature gel permeation chromatography (GPC). This test method uses commercially available polystyrene standards and equipment and is applicable to polyethylenes (excluding high pressure low density polyethylene???LDPE) and polypropylenes soluble in 1,2,4-trichlorobenzene (TCB) at 140??C. This test method is not absolute and requires calibration.Note 1???Size exclusion chromatography (SEC) often is used as an alternative name for gel permeation chromatography (GPC).Note 2???Specific methods and capabilities of users may vary with differences in columns, instrumentation, applications software, and practices between laboratories.Note 3???One general method is outlined herein; alternative analytical practices can be followed and are attached in notes where appropriate.Note 4???There is no known ISO equivalent to this standard. 1.2 The values stated in SI units, based on IEEE/ASTM S1-10, are to be regarded as the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：83.080.20 (Thermoplastic materials) CCS：发布：2012 实施：

ASTM D6474-1999(2006) 高温凝胶渗透色谱法测定聚烯烃分子量分布和平均分子量的标准试验方法
简介：This test method measures the molecular weight distribution and molecular weight averages of polyethylene (except LDPE) and polypropylene resins. Differences in molecular weight and molecular weight distribution significantly affect physical properties, such as morphology, strength, melt flow etc., and as a result, the final properties of products made from these resins.1.1 This test method covers the determination of molecular weight distributions and molecular weight averages of linear polyolefins by high temperature gel permeation chromatography (GPC). This test method uses commercially available polystyrene standards and equipment and is applicable to polyethylenes (excluding high pressure low density polyethylene-LDPE) and polypropylenes soluble in 1,2,4-trichlorobenzene (TCB) at 140C. This test method is not absolute and requires calibration.Note 1Size exclusion chromatography (SEC) often is used as an alternative name for gel permeation chromatography (GPC).Note 2Specific methods and capabilities of users may vary with differences in columns, instrumentation, applications software, and practices between laboratories.Note 3One general method is outlined herein; alternative analytical practices can be followed and are attached in notes where appropriate.Note 4There is no similar or equivalent ISO standard.1.2 The values stated in SI units, based on IEEE/ASTM S1-10, are to be regarded as the standard.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：83.080.20 (Thermoplastic materials) CCS：G04 发布：1999 实施：

ISO 13885-3-2020 凝胶渗透色谱法（GPC）第3部分:水作为洗脱剂
简介：
信息：ICS：87.060.20 CCS：发布：2020-07-08 实施：

SN/T 3002-2011 聚乙烯相对分子量和分子量分布的测定.凝胶渗透色谱法
简介：本标准规定了聚乙烯(除高压低密度聚乙烯)的相对分子量和分子量分布的凝胶渗透色谱测定方法。本标准适用于140℃时溶解于1,2,4-三氯苯的聚乙烯(除高压低密度聚乙烯)的相对分子量和分子量分布的测定。
信息：ICS： CCS：G31 发布：2011-09-09 实施：2012-04-01

ISO 13885-1:1998 色漆和清漆用粘合剂.凝胶渗透色谱法（GPC）.第1部分:四氢呋喃（THF）作为洗脱剂
简介：
信息：ICS：87.060.20 CCS：发布：1998-12-10 实施：

ISO 13885-3:2020 凝胶渗透色谱法（GPC）第3部分:水作为洗脱剂
简介：
信息：ICS：87.060.20 CCS：发布：2020-07-08 实施：

DIN 55672-3 Berichtigung 1-2009 凝胶渗透色谱法(GPC).第3部分:洗脱溶剂用水.技术勘误DIN 55672-3-2007
简介：
信息：ICS：71.040.50 CCS：G04 发布：2009-02 实施：

ISO 13885-1-1998 色漆和清漆用粘合剂凝胶渗透色谱法(GPC) 第1部分:用四氢呋喃作洗脱溶剂
简介：This part of ISO 13885 is one of a series of standards dealing with the sampling and testing of paints, varnishes and related products.It describes conditions for the determination of the molecular-mass distribution, number-average molecular mass Mnand mass-average molecular mass Mw of polymers that are soluble in THF (tetrahydrofuran) by gel permeation chromatography (GPC).It is possible that, in spite of the good repeatability obtained with this method, it cannot be used with certain polymer types because of specific interactions, such as adsorption within the sample/eluent/column system.The method is not an absolute one and requires calibration with commercially available unbranched-polystyrene standards that have been characterized by absolute methods. The results for samples of polymers other than polystyrene are therefore only comparable within groups of samples of the same type.The conditions specified in this part of ISO 13885 are not suitable for the GPC analysis of polymer samples with Mw values greater than 10 (see annex A).No correction methods, e.g. for the elimination of peak broadening, are included in this part of ISO 13885. If absolute molecular-mass values are required, an absolute method, e.g. membrane osmometry for Mn or light scattering for Mw, must be used.note: 1) Also known as size exclusion chromatography (SEC).
信息：ICS：87.060.20 CCS：G38 发布：1998-12 实施：

ISO 13885-2-2020 凝胶渗透色谱法（GPC）第2部分:N N-二甲酰乙酰胺（DMAC）作为洗脱剂
简介：
信息：ICS：87.060.20 CCS：发布：2020-07-08 实施：

BS ISO 13885-1-2008 涂料和清漆用粘合剂.凝胶渗透色谱法(GPC).用四氢呋喃(THF)作洗提液
简介：
信息：ICS：87.060.20 CCS：G52 发布：2008-11-30 实施：2008-11-30

ASTM D3536-91 用液排色谱法（凝胶渗透色谱-Gpc）测定聚苯乙烯分子量平均值和分子量分布的标准试验方法
简介：
信息：ICS： CCS：发布：1991-01-01 实施：1991-01-01

ASTM D6474-20 通过高温凝胶渗透色谱法测定聚烯烃的分子量分布和分子量平均值的标准测试方法
简介：
信息：ICS：83.080.20 CCS：发布：2020-04-01 实施：

ISO 13885-1-2008 涂料和清漆用粘合剂.凝胶渗透色谱法(GPC).第1部分:用四氢呋喃(THF)作洗提液
简介：This part of ISO 13885 describes the determination of the molar-mass distribution, number-average molarmass Mn and mass-average molar mass Mw of polymers that are soluble in THF (tetrahydrofuran) by gelpermeation chromatography (GPC)I).It is possible that, in spite of the good repeatability obtained with this method, it cannot be used with certainpolymer types because of specific interactions, such as adsorption within the sample/eluentJcolumn system.The method is not an absolute one and requires calibration with commercially available unbranched-polystyrene standards that have been characterized by absolute methods. The results for samples ofpolymers other than polystyrene are therefore only comparable within groups of samples of the same type.The conditions specified in this part of ISO 13885 are not suitable for the GPC analysis of polymer sampleswith .~/w values greater than 106 (see Annex C).No correction methods, e.g. for the elimination of peak broadening, are included in this part of ISO 13885. Ifabsolute molar-mass values are required, an absolute method, e.g. membrane osmometry for .Un or lightscattering for Mw, must be used.
信息：ICS：87.060.20 CCS：G52 发布：2008-08 实施：

ASTM D3593-80(1986)e1 使用通用校准的液体尺寸排除色谱法（凝胶渗透色谱法GPC）测定某些聚合物的平均分子量和分子量分布的试验方法
简介：
信息：ICS： CCS：发布：1986-01-01 实施：

KS M ISO 11344-2017(2022) 生胶-凝胶渗透色谱法测定溶液聚合物的分子质量分布
简介：
信息：ICS：83.040.10 CCS：发布：2017-12-29 实施：

ISO 13885-1:2008 色漆和清漆用粘合剂——凝胶渗透色谱法（GPC）第1部分:四氢呋喃（THF）洗脱液
简介：
信息：ICS：87.060.20 CCS：发布：2008-07-21 实施：

ASTM D6474-19 通过高温凝胶渗透色谱法测定聚烯烃的分子量分布和分子量平均值的标准测试方法
简介：
信息：ICS：83.080.20 CCS：/ 发布：0000-00-00 实施：0000-00-00

ISO 11344-2016 合成生橡胶.用凝胶渗透色谱法测定溶液聚合物分子质量的分布
简介：
信息：ICS：83.040.10 CCS：G34 发布：2016-10 实施：

DIN 55672-2-2008 凝胶渗透色谱法(GPC).第2部分:用N,N-二甲基乙酰胺(DMAC)作洗脱溶剂
简介：This standard describes the determination of the molecular weight distribution, number-average molecularweight Mr and weight-average molecular weight Mw of polymers that are soluble in DMAC (N,N-dimethylacetamide) by gel permeation chromatography (GPC).It is possible that, in spite of the good repeatability of the chromatograms obtained, this method cannot beused with certain polymer types because of specific interactions (e.g. adsorption) within the sample/eluent/-column system.The method is not an absolute one and requires calibration with commercially available unbranchedpolymethyl methacrylate standards that have been characterized by independent absolute methods. Theresults for samples of polymers other than polymethyl methacrylate are therefore only comparable withingroups of samples of the same type.The conditions specified in this standard are not suitable for the GPC analysis of polymer samples with Mwvalues greater than 10~6 g/mol (see Annex C).No correction methods (e.g. for the elimination of peak broadening) are included in this standard. If absolutemolecular weight values are required, an absolute method (e.g. membrane osmometry for Mn or lightscattering for Mw) shall be used.
信息：ICS：71.040.50 CCS：G63 发布：2008-06 实施：

ASTM D3536 用液排色谱法（凝胶渗透色谱-Gpc）测定聚苯乙烯分子量平均值和分子量分布的标准试验方法
简介：
信息：ICS： CCS：/ 发布：0000-00-00 实施：0000-00-00

NY/T 1860.35-2016 农药理化性质测定试验导则第35部分：聚合物分子量和分子量分布测定（凝胶渗透色谱法）
简介：
信息：ICS：65.02 CCS：B17 发布：2016-05-23 实施：2016-10-01

ISO 11344 Technical Corrigendum 1-2008 合成生橡胶.用凝胶渗透色谱法测定溶液聚合物分子质量的分布.技术勘误1
简介：This standard is Rubber, raw synthetic - Determination of the molecular-mass distribution of solution polymers by gel permeation chromatography; Technical Corrigendum 1
信息：ICS：83.040.10 CCS：G34 发布：2008-04-15 实施：

FD T66-028-2016 沥青粘合剂. 含焦油的烃类沥青粘合剂中焦油含量的测定. 凝胶渗透色谱法
简介：
信息：ICS：75.140 CCS：发布：实施：2016-03-02

NY/T 1860.36-2016 农药理化性质测定试验导则第36部分：聚合物低分子量组分含量测定（凝胶渗透色谱法）
简介：
信息：ICS：65.02 CCS：B17 发布：2016-05-23 实施：2016-10-01

SH/T 1759-2007 用凝胶渗透色谱法测定溶液聚合物分子量分布
简介：警告：使用本标准的人员应有正规实验室工作的实践经验。本标准并未指出所有可能的安全问题。使用者有责任采取适当的安全和健康措施，并保证符合国家有关法规规定的条件。本标准规定了溶液聚合物分子量 ( 用聚苯乙烯表示 ) 及其分子量分布的测定方法。本标准适用于可完全溶解于四氢呋喃（THF）的、分子量范围为5×10～1×10的溶液聚合物。
信息：ICS：83.060 CCS：G34 发布：2007-08-01 实施：2008-01-01

ASTM D3536-76e1 用液排色谱法（凝胶渗透色谱-Gpc）测定聚苯乙烯分子量平均值和分子量分布的标准试验方法
简介：
信息：ICS： CCS：发布：实施：

DIN 55672-3-2016 凝胶渗透色谱法(GPC).第3部分:用水作洗脱溶剂
简介：
信息：ICS：71.040.50 CCS：G04 发布：2016-03 实施：

DIN 55672-1-2007 凝胶渗透色谱法(GPC).第1部分:用四氢呋喃(THF)作洗脱溶剂
简介：This standard describes the determination of the molecular weight distribution, number-average molecularweight Mn and weight-average molecular weight ,Mw of polymers that are soluble in THF (tetrahydrofuran) bygel permeation chromatography (GPC).It is possible that, in spite of the good repeatability of the chromatograms obtained, this method cannot beused with certain polymer types because of specific interactions (e.g. adsorption) within thesample/eluent/column system.The method is not an absolute one and requires calibration with commercially available unbranchedpolystyrene standards that have been characterized by independent absolute methods. The results for samples of polymers other than polystyrene are therefore only comparable within groups of samples of thesame type.The conditions specified in this standard are not suitable for the GPC analysis of polymer samples with Mwvalues greater than 10~6 g/mol (see Annex C).No correction methods (e.g. for the elimination of peak broadening) are included in this standard. If absolutemolecular weight values are required, an absolute method (e.g. membrane osmometry for Mn or lightscattering for Mw) shall be used.
信息：ICS：71.040.50 CCS：G04 发布：2007-08 实施：

简介： 信息：