紫外可见分光光度计检测标准紫外可见分光光度计-中析研究所检测

(CMA)

(CNAS)

(ISO)

(高新技术企业)

紫外可见分光光度计相关标准参考信息

GB/T 26810-2011 可见分光光度计
简介：本标准规定了可见分光光度计的产品分级、技术要求、试验方法、检验规则、标志、包装、运输、贮存。本标准适用于主要光谱区为360 nm～900 nm，波长连续可调的可见分光光度计（以下简称"仪器"），与此波长范围相近的专用分光光度计也可参考使用。
信息：ICS：71.040.10 CCS：N53 发布：2011-07-29 实施：2011-12-01

ASTM D6756-09 使用便携式可见分光光度计测定红色染料浓度的标准测试方法和柴油和加热油的ASTM颜色的估计
简介：
信息：ICS：71.040.50 CCS：发布：2009-03-01 实施：

JJG 689-1990 紫外、可见、近红外分光光度计
简介：
信息：ICS： CCS：A61 发布：1990-06-08 实施：1990-10-01

GB/T 26798-2011 单光束紫外可见分光光度计
简介：本标准规定了单光束紫外可见分光光度计的分级、要求、试验方法、检验规则和标志、包装、运输及贮存等。本标准适用于主要光谱区为200nm～900nm，波长连续可调的单光束紫外可见分光光度计（以下简称“仪器”），波长范围与此相近的专用分光光度计也可参考使用。
信息：ICS：71.040.01 CCS：N53 发布：2011-07-29 实施：2011-12-01

ASTM E925-2009(2014) 光谱缝宽不超过2 nm的可见紫外线分光光度计的校准监控的标准实施规程
简介：4.1x00a0;This practice permits an analyst to compare the performance of an instrument to the manufacturerx0027;s supplied performance specifications and to verify its suitability for continued routine use. It also provides generation of calibration monitoring data on a periodic basis, forming a base from which any changes in the performance of the instrument will be evident. 1.1x00a0;This practice covers the parameters of spectrophotometric performance that are critical for testing the adequacy of instrumentation for most routine tests and methods2 within the wavelength range of 200 to 700 nm and the absorbance range of 0 to 2. The recommended tests provide a measurement of the important parameters controlling results in spectrophotometric methods, but it is specifically not to be inferred that all factors in instrument performance are measured. 1.2x00a0;This practice may be used as a significant test of the performance of instruments for which the spectral bandwidth does not exceed 2 nm and for which the manufacturerx0027;s specifications for wavelength and absorbance accuracy do not exceed the performance tolerances employed here. This practice employs an illustrative tolerance of x00b1;18201;% relative for the error of the absorbance scale over the range of 0.2 to 2.0, and of x00b1;1.0 nm for the error of the wavelength scale. A suggested maximum stray radiant power ratio of 4 x00d7; 10-4 yields lt;18201;% absorbance bias at an absorbance of 2. These tolerances are chosen to be compatible with many chemical applications while comfortably exceeding the uncertainty of the certified values for the reference materials and typical manufacturerx0027;s specifications for error in the wavelength and absorbance scales of the instrument under test. The user is encouraged to develop and use tolerance values more appropriate to the requirements of the end use application. This procedure is designed to verify quantitative performance on an ongoing basis and to compare one instrumentx0027;s performance with that of other similar units. Refer to Practice E275 to extensively evaluate the performance of an instrument. 1.3x00a0;This practice should be performed on a periodic basis, the frequency of which depends on the physical environment within which the instrumentation is used. Thus, units handled roughly or used under adverse conditions (exposed to dust, chemical vapors, vibrations, or combinations thereof) should be tested more frequently than those not exposed to such conditions. This practice should also be performed after any significant repairs are made on a unit, such as those involving the optics, detector, or radiant energy source. 1.4x00a0;The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：17.180.30 (Optical measuring instruments); 71.040. CCS：发布：2009 实施：

JJG 682-1990 双光束紫外可见分光光度计检定规程
简介：
信息：ICS： CCS：A61 发布：1990-01-01 实施：1990-09-01

GB/T 26813-2011 双光束紫外可见分光光度计
简介：本标准规定了双光束紫外可见分光光度计的分级、要求、试验方法、检验规则和标志、包装、运输及贮存等。本标准适用于具有独立参比光束及独立参比样品池，主要光谱区为200nm～900nm，波长连续可调的双光束紫外可见分光光度计（以下简称“仪器”），波长范围与此相近的双光束分光光度计也可参考使用。
信息：ICS：71.040.01 CCS：N53 发布：2011-07-29 实施：2011-12-01

ASTM E275-08 紫外和可见分光光度计的描述和测量性能
简介：
信息：ICS：17.180.30 CCS：发布：2008-10-15 实施：

JJG(地质) 1002-1990 紫外/可见分光光度计检定规程
简介：
信息：ICS： CCS：A60 发布：1990 实施：

ASTM E925-09(2022) 光谱带宽不超过2nm的紫外可见分光光度计校准的监测标准实施规程
简介：
信息：ICS：17.180.30 CCS：发布：2022-11-01 实施：

ASTM E275-2008(2013) 说明和测量紫外线和可见分光光度计性能的标准操作规程
简介：4. Significance and UseTop Bottom 4.1 This practice permits an analyst to compare the general performance of an instrument, as it is being used in a specific spectrophotometric method, with the performance of instruments used in developing the method. 1.1 This practice covers the description of requirements of spectrophotometric performance, especially for test methods, and the testing of the adequacy of available equipment for a specific method (for example, qualification for a given application). The tests give a measurement of some of the important parameters controlling results obtained in spectrophotometric methods, but it is specifically not to be concluded that all the factors in instrument performance are measured, or in fact may be required for a given application. 1.1.1 This practice is primarily directed to dispersive spectrophotometers used for transmittance measurements rather than instruments designed for diffuse transmission and diffuse reflection. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：17.180.30 (Optical measuring instruments) CCS：发布：2008 实施：

简介： 信息：

ASTM E275-08(2022) 描述和测量紫外和可见分光光度计性能的标准实施规程
简介：
信息：ICS：17.180.30 CCS：发布：2022-01-01 实施：

ASTM E275-2008 说明和测量紫外线可见分光光度计的性能的标准实施规程
简介：This practice permits an analyst to compare the general performance of an instrument, as it is being used in a specific spectrophotometric method, with the performance of instruments used in developing the method.1.1 This practice covers the description of requirements of spectrophotometric performance, especially for test methods, and the testing of the adequacy of available equipment for a specific method (for example, qualification for a given application). The tests give a measurement of some of the important parameters controlling results obtained in spectrophotometric methods, but it is specifically not to be concluded that all the factors in instrument performance are measured, or in fact may be required for a given application. 1.1.1 This practice is primarily directed to dispersive spectrophotometers used for transmittance measurements rather than instruments designed for diffuse transmission and diffuse reflection. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：17.180.30 (Optical measuring instruments) CCS：N33 发布：2008 实施：

简介： 信息：

ASTM E958-13(2021) 紫外可见分光光度计光谱带宽估算标准实践
简介：
信息：ICS：17.180.30 CCS：发布：2021-04-01 实施：

JJG 178-2007 紫外、可见、近红外分光光度计检定规程
简介：本规程适用于波长范围190nm～2600nm，波长连续可调的可见、紫外-可见、紫外-可见-近红外分光光度计的首次检定、后续检定和使用中检验。
信息：ICS： CCS：A61 发布：2007-11-21 实施：2008-05-21

简介： 信息：

ASTM D7058-19 用便携式可见分光光度计测定航空涡轮燃料和煤油的红色染料浓度和赛波特颜色估计的标准试验方法
简介：
信息：ICS：75.160.20 CCS：发布：2019-05-01 实施：

ASTM E958-93(2005) 紫外可见分光光度计实际光谱带宽测量的标准实施规程
简介：
信息：ICS：17.180.30 CCS：发布：2005-04-01 实施：

简介： 信息：

JJF 1641-2017 紫外可见分光光度计型式评价大纲
简介：
信息：ICS： CCS：发布：2017-09-26 实施：2017-12-26

ASTM D7058-04 用便携式可见分光光度计测定航空涡轮燃料和煤油的红色染料浓度和赛波特颜色估计的标准试验方法
简介：
信息：ICS：75.160.20 CCS：发布：2004-07-01 实施：

简介： 信息：

ASTM D6756-17 使用便携式可见分光光度计测定红色染料浓度的标准测试方法和柴油和加热油的ASTM颜色的估计
简介：
信息：ICS：71.040.50 CCS：发布：2017-05-01 实施：

ASTM E925-83(1994)e1 光谱狭缝宽度不超过2nm的紫外-可见分光光度计校准的监测标准实施规程
简介：
信息：ICS：17.180.30 CCS：发布：2002-03-10 实施：

简介： 信息：

ASTM D6756-2017 用便携式可见分光光度计测定柴油燃料和燃油红染料浓度并且评估ASTM颜色的标准试验方法
简介：5.1x00a0;In the United States, high sulfur content (defined by the United States Environmental Protection Agency (USEPA)) middle distillate products and diesel fuel used for off-road purposes, other than aviation turbine fuel, are required by government agencies to contain red dye. The dye concentration required to be present in high-sulfur and off-road diesel products is regulated by the United States Environmental Protection Agency and the United States Internal Revenue Service, respectively. 5.2x00a0;Some fuels that are readily exchanged in the market have a color specification. The color of the base fuel is masked by the presence of the red dye. This test method provides a means of estimating the base color of Number 1 and Number 2 diesel fuel and heating oil in the presence of red dye. 5.3x00a0;The test method provides a means to indicate conformance to contractual and legal requirements. 1.1x00a0;This test method covers the determination of the red dye concentration of diesel fuel and heating oil and the estimation of the ASTM color of undyed and red-dyed diesel fuel and heating oil. The test method is appropriate for use with diesel fuel and heating oil of Grades 1 and 2 described in Specifications D396, D975, D2880, and D3699. Red dye concentrations are determined at levels equivalent to 0.18201;mg/L to 208201;mg/L of Solvent Red 26 in samples with ASTM colors ranging from 0.5 to 5. The ASTM color of the base fuel of red-dyed samples with concentration levels equivalent to 0.18201;mg/L to 208201;mg/L of Solvent Red 26 is estimated for the ASTM color range from 0.5 to 5. The ASTM color of undyed samples is estimated over the ASTM color range of 0.5 to 5. 1.2x00a0;The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.4x00a0;This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
信息：ICS：71.040.50 CCS：E34 发布：2017 实施：

ASTM E925-02 光谱狭缝宽度不超过2nm的紫外-可见分光光度计校准的监测标准实施规程
简介：
信息：ICS：17.180.30 CCS：发布：2002-03-10 实施：

简介： 信息：

ASTM D6756-10(2015) 使用便携式可见分光光度计测定红色染料浓度的标准测试方法和柴油和加热油的ASTM颜色的估计
简介：
信息：ICS：71.040.50 CCS：发布：2015-10-01 实施：

ASTM D6756-02 使用便携式可见分光光度计测定红色染料浓度的标准测试方法和柴油和加热油的ASTM颜色的估计
简介：
信息：ICS：71.040.50 CCS：发布：2002-02-10 实施：

简介： 信息：

ASTM E925-09(2014) 用于监测光谱带宽不超过2 nm的紫外可见分光光度计校准的标准实践
简介：
信息：ICS：17.180.30 CCS：发布：2014-05-01 实施：

ASTM E275-2001 说明和测量紫外线,可见和近红外线分光光度计的性能的标准操作规程
简介：This practice permits an analyst to compare the general performance of his instrument, as he is using it in a specific spectrophotometric method, with the performance of instruments used in developing the method. 1.1 This practice covers the description of requirements of spectrophotometric performance especially for ASTM methods, and the testing of the adequacy of available equipment for a specific method. The tests give a measurement of some of the important parameters controlling results obtained in spectrophotometric methods, but it is specifically not to be concluded that all the factors in instrument performance are measured.1.1.1 This practice is not to be used (1) as a rigorous test of performance of instrumentation, or (2) to intercompare the quantitative performance of instruments of different design.1.1.2 This practice is primarily directed to dispersive spectrophotometers used for transmittance measurements rather than instruments designed for diffuse transmission and diffuse reflection.
信息：ICS：17.180.30 (Optical measuring instruments) CCS：N33 发布：2001 实施：

简介： 信息：

ASTM D7058-04(2014) 用便携式可见分光光度计测定航空涡轮燃料和煤油的红色染料浓度和赛波特颜色估计的标准试验方法
简介：
信息：ICS：75.160.20 CCS：发布：2014-05-01 实施：

JB/T 9324-1999 可见分光光度计
简介：本标准规定了可见分光光度计的产品分类、技术方法、试验方法、检验规则、标志、包装、运输、贮存等。本标准适用于主要光谱区为360nm～800nm的可见分光光度计。
信息：ICS： CCS：N33 发布：1999-08-06 实施：2000-01-01

简介： 信息：

ASTM E275-08(2013) 描述和测量紫外和可见分光光度计性能的标准实践
简介：
信息：ICS：17.180.30 CCS：发布：2013-01-01 实施：

ASTM E958-93(1999) 紫外可见分光光度计实际光谱带宽测量的标准实施规程
简介：
信息：ICS：17.180.30 CCS：发布：1999-02-10 实施：

简介： 信息：

ASTM E958-13 紫外可见分光光度计光谱带宽估算标准实践
简介：
信息：ICS：17.180.30 CCS：发布：2013-01-01 实施：

JJG 375-1996 单光束紫外-可见分光光度计检定规程
简介：
信息：ICS： CCS：A61 发布：1996-01-01 实施：1997-06-01

简介： 信息：

ASTM D6756-10 使用便携式可见分光光度计测定红色染料浓度的标准测试方法和柴油和加热油的ASTM颜色的估计
简介：
信息：ICS：71.040.50 CCS：发布：2010-10-01 实施：

JJG 178-1996 可见分光光度计检定规程
简介：
信息：ICS： CCS：A61 发布：1996-01-01 实施：1997-06-01

简介： 信息：

ASTM D6756-2010(2015) 使用便携式可见分光光度计测定柴油燃料和加热油的红染料浓度和ASTM颜色评估的标准试验方法
简介：5.1x00a0;In the United States, high sulfur content (defined by the United States Environmental Protection Agency (USEPA)) middle distillate products and diesel fuel used for off-road purposes, other than aviation turbine fuel, are required by government agencies to contain red dye. The dye concentration required to be present in high sulfur and off-road diesel products is regulated by the United States Environmental Protection Agency and the United States Internal Revenue Service, respectively. 5.2x00a0;Some fuels that are readily exchanged in the market have a color specification. The color of the base fuel is masked by the presence of the red dye. This test method provides a means of estimating the base color of Number 1 and Number 2 diesel fuel and heating oil in the presence of red dye. 5.3x00a0;The test method provides a means to indicate conformance to contractual and legal requirements. 1.1x00a0;This test method covers the determination of the red dye concentration of diesel fuel and heating oil and the estimation of the ASTM color of undyed and red-dyed diesel fuel and heating oil. The test method is appropriate for use with diesel fuel and heating oil of Grades 1 and 2 described in Specifications D396, D975, D2880 and D3699. Red dye concentrations are determined at levels equivalent to 0.18201;mg/L to 208201;mg/L of Solvent Red 26 in samples with ASTM colors ranging from 0.5 to 5. The ASTM color of the base fuel of red-dyed samples with concentration levels equivalent to 0.18201;mg/L to 208201;mg/L of Solvent Red 26 is estimated for the ASTM color range from 0.5 to 5. The ASTM color of undyed samples is estimated over the ASTM color range of 0.5 to 5. 1.2x00a0;The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：71.040.50 CCS：发布：2010 实施：

JB/T 6778-1993 紫外可见近红外分光光度计
简介：本标准规定了紫外可见近红外分光光度计的型式和技术条件。本标准适用于ZBN 33009所规定的波长范围的紫外可见近红外分光光度计。
信息：ICS：17.180.30 CCS：N33 发布：1993-07-09 实施：1994-01-01

简介： 信息：

ASTM D6756-09a 使用便携式可见分光光度计测定红色染料浓度的标准测试方法和柴油和加热油的ASTM颜色的估计
简介：
信息：ICS：71.040.50 CCS：发布：2009-12-01 实施：

JB/T 6777-1993 紫外可见分光光度计
简介：本标准规定了紫外、可见分光光度计的型式和技术条件。本标准适用于ZBN 33009所规定的紫外可见分光光度计。
信息：ICS：17.180.30 CCS：N33 发布：1993-07-09 实施：1994-01-01

简介： 信息：

ASTM D7058-04(2009) 用便携式可见分光光度计测定航空涡轮燃料和煤油的红色染料浓度和赛波特颜色估计的标准试验方法
简介：
信息：ICS：75.160.20 CCS：发布：2009-12-01 实施：

ASTM E958-1993(2005) 紫外线-可见分光光度计的实用光谱带宽的测量
简介：This practice should be used by a person who develops an analytical method to ensure that the spectral bandwidths cited in the practice are actually the ones used. Note 18212;The method developer should establish the spectral bandwidths that can be used to obtain satisfactory results. This practice should be used to determine whether a spectral bandwidth specified in a method can be realized with a given spectrophotometer and thus whether the instrument is suitable for use in this application. This practice allows the user of a spectrophotometer to determine the actual spectral bandwidth of the instrument under a given set of conditions and to compare the result to the spectral bandwidth calculated from data given in the manufacturerrsquo;literature or indicated by the instrument. Instrument manufacturers can use this practice to measure and describe the practical spectral bandwidth of an instrument over its entire wavelength operating range. This practice is highly prefered to the general practice of stating the limiting or the theoretical spectral bandwidth at a single wavelength.1.1 This practice describes a procedure for measuring the practical spectral bandwidth of a spectrophotometer in the wavelength region of 185 to 820 nm. Practical spectral bandwidth is the spectral bandwidth of an instrument operated at a given integration period and a given signal-to-noise ratio.1.2 This practice is applicable to instruments that utilize servo-operated slits and maintain a constant period and a constant signal-to-noise ratio as the wavelength is automatically scanned. It is also applicable to instruments that utilize fixed slits and maintain a constant servo loop gain by automatically varying gain or dynode voltage. In this latter case, the signal-to-noise ratio varies with wavelength. It can also be used on instruments that utilize some combination of the two designs, as well as on those that vary the period during the scan. For digitized instruments, refer to the manufacturer''s manual.1.3 This practice does not cover the measurement of limiting spectral bandwidth, defined as the minimum spectral bandwidth achievable under optimum experimental conditions.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：17.180.30 (Optical measuring instruments) CCS：N30 发布：1993 实施：

简介： 信息：

ASTM E925-09 光谱狭缝宽度不超过2nm的紫外-可见分光光度计校准的监测标准实施规程
简介：
信息：ICS：17.180.30 CCS：发布：2009-10-01 实施：

ASTM E275-1993 说明和测量紫外线,可见和近红外线分光光度计的性能的标准操作规程
简介：1.1 This practice covers the description of requirements of spectrophotometric performance especially for ASTM methods, and the testing of the adequacy of available equipment for a specific method. The tests give a measurement of some of the important parameters controlling results obtained in spectrophotometric methods, but it is specifically not to be concluded that all the factors in instrument performance are measured.1.1.1 This practice is not to be used (1) as a rigorous test of performance of instrumentation, or (2) to intercompare the quantitative performance of instruments of different design.1.1.2 This practice is primarily directed to dispersive spectrophotometers used for transmittance measurements rather than instruments designed for diffuse transmission and diffuse reflection.
信息：ICS：17.180.30 (Optical measuring instruments) CCS：N33 发布：1993 实施：

简介： 信息：