ASTM D 5453检测标准

发布时间：2023-02-07 14:24:15 • 阅读量： • 来源：中析研究所

ASTM D 5453相关标准参考信息

ASTM D5453-19a 火焰点火发动机燃料柴油发动机燃料和发动机油通过紫外线荧光测定的总硫含量的标准试验方法
简介：
信息：ICS：75.100 CCS：发布：2019-07-01 实施：

ASTM D5453-04 用紫外线荧光法测定汽车燃料和油中轻烃中总硫的标准试验方法
简介：
信息：ICS：75.100 CCS：发布：2004-11-01 实施：

简介： 信息：

ASTM D5453-19 火焰点火发动机燃料柴油发动机燃料和发动机油通过紫外线荧光测定的总硫含量的标准试验方法
简介：
信息：ICS：75.100 CCS：发布：2019-05-01 实施：

ASTM D5453-2004 用紫外荧光法测定轻质烃、发动机燃料和油中总硫含量的标准试验方法
简介：1.1 This test method covers the determination of total sulfur in liquid hydrocarbons, boiling in the range from approximately 25 to 400176;C, with viscosities between approximately 0.2 and 20 cSt (mm178;/S) at room temperature. 1.2 Three separate interlaboratory studies (ILS) on precision, and two other investigations that resulted in an ASTM research report, have determined that this test method is applicable to naphthas, distillates, oils, ethanol, Fatty Acid Methyl Ester (FAME), and motor fuels; such as gasoline, oxygen enriched gasoline (M-85, RFG), diesel, biodiesel and jet fuel. Samples containing 1.0 to 8000 mg/kg total sulfur can be analyzed (Note 1).Note 18212;Estimates of the pooled limit of quantification (PLOQ) for each of the three precision studies were calculated. Values ranged between less than 1.0 and less than 5.0 mg/kg (see Section 8 and 14.1).1.3 This test method is applicable for total sulfur determination in liquid hydrocarbons containing less than 0.35 % (m/m) halogen(s).1.4 The values stated in SI units are to be regarded as standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See 3.1, 6.3, 6.4, Section 7, and 8.1.
信息：ICS：75.100 (Lubricants, industrial oils and related pr CCS：E31 发布：2004 实施：

简介： 信息：

ASTM D5453-16 火焰点火发动机燃料柴油发动机燃料和发动机油通过紫外线荧光测定的总硫含量的标准试验方法
简介：
信息：ICS：75.100 CCS：发布：2016-04-15 实施：

ASTM D5453-03a 用紫外线荧光法测定汽车燃料和油中轻烃中总硫的标准试验方法
简介：
信息：ICS：75.100 CCS：发布：2003-09-10 实施：

简介： 信息：

ASTM D5453-16e1 火焰点火发动机燃料柴油发动机燃料和发动机油通过紫外线荧光测定的总硫含量的标准试验方法
简介：
信息：ICS：75.100 CCS：发布：2016-04-15 实施：

ASTM D5453-03 用紫外线荧光法测定汽车燃料和油中轻烃中总硫的标准试验方法
简介：
信息：ICS：75.100 CCS：发布：2003-08-10 实施：

简介： 信息：

ASTM D5453-2016e1 采用紫外荧光法测定轻烃, 火花点火发动机燃料, 柴油发动机燃料和发动机油总硫含量的标准试验方法
简介：4.1x00a0;Some process catalysts used in petroleum and chemical refining can be poisoned when trace amounts of sulfur bearing materials are contained in the feedstocks. This test method can be used to determine sulfur in process feeds sulfur in finished products, and can also be used for purposes of regulatory control. 1.1x00a0;This test method covers the determination of total sulfur in liquid hydrocarbons, boiling in the range from approximately 258201;x00b0;C to 4008201;x00b0;C, with viscosities between approximately 0.28201;cSt and 208201;cSt (mm2/s) at room temperature. 1.2x00a0;Three separate interlaboratory studies (ILS) on precision, and three other investigations that resulted in an ASTM research report, have determined that this test method is applicable to naphthas, distillates, engine oil, ethanol, Fatty Acid Methyl Ester (FAME), and engine fuel such as gasoline, oxygen enriched gasoline (ethanol blends, E-85, M-85, RFG), diesel, biodiesel, diesel/biodiesel blends, and jet fuel. Samples containing 1.08201;mg/kg to 80008201;mg/kg total sulfur can be analyzed (Note 1). Note 1:x00a0;Estimates of the pooled limit of quantification (PLOQ) for the precision studies were calculated. Values ranged between less than 1.08201;mg/kg and less than 5.0 mg/kg (see Section 8 and 15.1). 1.3x00a0;This test method is applicable for total sulfur determination in liquid hydrocarbons containing less than 0.358201;% (m/m) halogen(s). 1.4x00a0;The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For warning statements, see 3.1, 6.3, 6.4, Section 7, and 8.1.
信息：ICS：75.100 CCS：发布：2016 实施：

ASTM D5453-2003a 紫外线荧光测量法测定轻质烃、发动机燃料和油中硫总含量的试验方法
简介：1.1 This test method covers the determination of total sulfur in liquid hydrocarbons, boiling in the range from approximately 25 to 400176;C, with viscosities between approximately 0.2 and 20 cSt (mm178;/S) at room temperature. 1.2 Three separate interlaboratory studies (ILS) on precision, and two other investigations that resulted in an ASTM research report, have determined that this test method is applicable to naphthas, distillates, oils, ethanol, Fatty Acid Methyl Ester (FAME), and motor fuels; such as gasoline, oxygen enriched gasoline (M-85, RFG), diesel, biodiesel and jet fuel. Samples containing 1.0 to 8000 mg/kg total sulfur can be analyzed (Note 1).Note 18212;Estimates of the pooled limit of quantification (PLOQ) for each of the three precision studies were calculated. Values ranged between less than 1.0 and less than 5.0 mg/kg (see Section 8 and 14.1).1.3 This test method is applicable for total sulfur determination in liquid hydrocarbons containing less than 0.35 % (m/m) halogen(s).1.4 The values stated in SI units are to be regarded as standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See 3.1, 6.3, 6.4, Section 7, and 8.1.
信息：ICS：75.100 (Lubricants, industrial oils and related pr CCS：E31 发布：2003 实施：

简介： 信息：

ASTM D5453-2016 采用紫外荧光法测定轻烃, 火花点火发动机燃料, 柴油发动机燃料和发动机油总硫含量的标准试验方法
简介：4.1x00a0;Some process catalysts used in petroleum and chemical refining can be poisoned when trace amounts of sulfur bearing materials are contained in the feedstocks. This test method can be used to determine sulfur in process feeds sulfur in finished products, and can also be used for purposes of regulatory control. 1.1x00a0;This test method covers the determination of total sulfur in liquid hydrocarbons, boiling in the range from approximately 258201;x00b0;C to 4008201;x00b0;C, with viscosities between approximately 0.28201;cSt and 208201;cSt (mm2/S) at room temperature. 1.2x00a0;Three separate interlaboratory studies (ILS) on precision, and three other investigations that resulted in an ASTM research report, have determined that this test method is applicable to naphthas, distillates, engine oil, ethanol, Fatty Acid Methyl Ester (FAME), and engine fuel such as gasoline, oxygen enriched gasoline (ethanol blends, E-85, M-85, RFG), diesel, biodiesel, diesel/biodiesel blends, and jet fuel. Samples containing 1.08201;mg/kg to 80008201;mg/kg total sulfur can be analyzed (Note 1). Note 1:x00a0;Estimates of the pooled limit of quantification (PLOQ) for the precision studies were calculated. Values ranged between less than 1.08201;mg/kg and less than 5.0 mg/kg (see Section 8 and 15.1). 1.3x00a0;This test method is applicable for total sulfur determination in liquid hydrocarbons containing less than 0.358201;% (m/m) halogen(s). 1.4x00a0;The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For warning statements, see 3.1, 6.3, 6.4, Section 7, and 8.1.
信息：ICS：75.100 CCS：发布：2016 实施：

ASTM D5453-2003 紫外线荧光测量法测定轻质烃、发动机燃料和油中硫总含量的试验方法
简介：1.1 This test method covers the determination of total sulfur in liquid hydrocarbons, boiling in the range from approximately 25 to 400176;C, with viscosities between approximately 0.2 and 20 cSt (mm178;/S) at room temperature. 1.2 Three separate interlaboratory studies (ILS) on precision, and two other investigations that resulted in an ASTM research report, have determined that this test method is applicable to naphthas, distillates, oils, ethanol, Fatty Acid Methyl Ester (FAME), and motor fuels; such as gasoline, oxygen enriched gasoline (M-85, RFG), diesel, biodiesel and jet fuel. Samples containing 1.0 to 8000 mg/kg total sulfur can be analyzed (Note 1).Note 18212;Estimates of the pooled limit of quantification (PLOQ) for each of the three precision studies were calculated. Values ranged between less than 1.0 and less than 5.0 mg/kg (see Section 8 and 14.1).1.3 This test method is applicable for total sulfur determination in liquid hydrocarbons containing less than 0.35 % (m/m) halogen(s).1.4 The values stated in SI units are to be regarded as standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See 3.1, 6.3, 6.4, Section 7, and 8.1.
信息：ICS：75.100 (Lubricants, industrial oils and related pr CCS：E31 发布：2003 实施：

简介： 信息：

ASTM D5453-12 火焰点火发动机燃料柴油发动机燃料和发动机油通过紫外线荧光测定的总硫含量的标准试验方法
简介：
信息：ICS：75.100 CCS：发布：2012-11-01 实施：

ASTM D5453-00 用紫外线荧光法测定汽车燃料和油中轻烃中总硫的标准试验方法
简介：
信息：ICS： CCS：发布：2000-01-10 实施：

简介： 信息：

ASTM D5453-2012 紫外线荧光测量法测定轻质烃、火花点火发动机燃料、柴油发动机油和发动机油总硫量的标准试验方法
简介：4.1x00a0;Some process catalysts used in petroleum and chemical refining can be poisoned when trace amounts of sulfur bearing materials are contained in the feedstocks. This test method can be used to determine sulfur in process feeds sulfur in finished products, and can also be used for purposes of regulatory control. 1.1x00a0;This test method covers the determination of total sulfur in liquid hydrocarbons, boiling in the range from approximately 25 to 400x00b0;C, with viscosities between approximately 0.2 and 20 cSt (mm 2/S) at room temperature. 1.2x00a0;Three separate interlaboratory studies (ILS) on precision, and three other investigations that resulted in an ASTM research report, have determined that this test method is applicable to naphthas, distillates, engine oil, ethanol, Fatty Acid Methyl Ester (FAME), and engine fuel such as gasoline, oxygen enriched gasoline (ethanol blends, E-85, M-85, RFG), diesel, biodiesel, diesel/biodiesel blends, and jet fuel. Samples containing 1.0 to 8000 mg/kg total sulfur can be analyzed (Note 1).Note 1x2014;Estimates of the pooled limit of quantification (PLOQ) for the precision studies were calculated. Values ranged between less than 1.0 and less than 5.0 mg/kg (see Section 8 and 15.1). 1.3x00a0;This test method is applicable for total sulfur determination in liquid hydrocarbons containing less than 0.358201;% (m/m) halogen(s). 1.4x00a0;The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For warning statements, see 3.1, 6.3, 6.4, Section 7, and 8.1.
信息：ICS：75.100 (Lubricants, industrial oils and related pr CCS：E34 发布：2012 实施：

ASTM D5453-00e1 用紫外线荧光法测定汽车燃料和油中轻烃中总硫的标准试验方法
简介：
信息：ICS：75.100 CCS：发布：2000-01-10 实施：

简介： 信息：

ASTM D5453-09 火焰点火发动机燃料柴油发动机燃料和发动机油通过紫外线荧光测定的总硫含量的标准试验方法
简介：
信息：ICS：75.100 CCS：发布：2009-06-15 实施：

ASTM D5453-2000 用紫外荧光法测定轻质烃、发动机燃料和油中总的硫含量的标准试验方法
简介：1.1 This test method covers the determination of total sulfur in liquid hydrocarbons, boiling in the range from approximately 25 to 400oC, with viscosities between approximately 0.2 and 20 cSt (mm 2/S) at room temperature. 1.2 Three separate inter-laboratory studies (ILS) on precision have determined that this test method is applicable to naphthas, distillates, oils, and motor fuels: such as gasoline, oxygen enriched gasoline (M-85, RFG), diesel, biodiesel and jet fuel. Samples containing 1.0 to 8000 mg/kg total sulfur can be analyzed (Note 1).Note 1-Estimates of the pooled limit of quantification (PLOQ) for each of the three precision studies were calculated. Values ranged between less than 1.0 and less than 5.0 mg/kg (see Section 8 and 14.1).1.3 This test method is applicable for total sulfur determination in liquid hydrocarbons containing less than 0.35 % (m/m) halogen(s).1.4 The values stated in SI units are to be regarded as standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See 3.1, 6.3, 6.4, 8.1 and Section 7.
信息：ICS： CCS：E31 发布：2000 实施：

简介： 信息：

ASTM D5453-2009 紫外线荧光测量法测定轻质烃、火花点火发动机燃料、柴油发动机油和发动机油总硫量的标准试验方法
简介：Some process catalysts used in petroleum and chemical refining can be poisoned when trace amounts of sulfur bearing materials are contained in the feedstocks. This test method can be used to determine sulfur in process feeds sulfur in finished products, and can also be used for purposes of regulatory control.1.1 This test method covers the determination of total sulfur in liquid hydrocarbons, boiling in the range from approximately 25 to 400x00B0;C, with viscosities between approximately 0.2 and 20 cSt (mm2/S) at room temperature. 1.2 Three separate interlaboratory studies (ILS) on precision, and three other investigations that resulted in an ASTM research report, have determined that this test method is applicable to naphthas, distillates, engine oil, ethanol, Fatty Acid Methyl Ester (FAME), and engine fuel such as gasoline, oxygen enriched gasoline (ethanol blends, E-85, M-85, RFG), diesel, biodiesel, diesel/biodiesel blends, and jet fuel. Samples containing 1.0 to 8000 mg/kg total sulfur can be analyzed (Note 1). Note 18212;Estimates of the pooled limit of quantification (PLOQ) for the precision studies were calculated. Values ranged between less than 1.0 and less than 5.0 mg/kg (see Section 8 and 15.1). 1.3 This test method is applicable for total sulfur determination in liquid hydrocarbons containing less than 0.35 % (m/m) halogen(s). 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For warning statements, see 3.1, 6.3, 6.4, Section 7, and 8.1.
信息：ICS：75.100 (Lubricants, industrial oils and related pr CCS：E34 发布：2009 实施：

ASTM D5453-2000e1 用紫外荧光法测定轻质烃、发动机燃料和油中总的硫含量的标准试验方法
简介：1.1 This test method covers the determination of total sulfur in liquid hydrocarbons, boiling in the range from approximately 25 to 400oC, with viscosities between approximately 0.2 and 20 cSt (mm 2/S) at room temperature. 1.2 Three separate inter-laboratory studies (ILS) on precision have determined that this test method is applicable to naphthas, distillates, oils, and motor fuels: such as gasoline, oxygen enriched gasoline (M-85, RFG), diesel, biodiesel and jet fuel. Samples containing 1.0 to 8000 mg/kg total sulfur can be analyzed (Note 1).Note 1-Estimates of the pooled limit of quantification (PLOQ) for each of the three precision studies were calculated. Values ranged between less than 1.0 and less than 5.0 mg/kg (see Section 8 and 14.1).1.3 This test method is applicable for total sulfur determination in liquid hydrocarbons containing less than 0.35 % (m/m) halogen(s).1.4 The values stated in SI units are to be regarded as standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See 3.1, 6.3, 6.4, 8.1 and Section 7.
信息：ICS：75.100 (Lubricants, industrial oils and related pr CCS：E31 发布：2000 实施：

简介： 信息：

ASTM D5453-08b 火焰点火发动机燃料柴油发动机燃料和发动机油通过紫外线荧光测定的总硫含量的标准试验方法
简介：
信息：ICS：75.100 CCS：发布：2008-07-01 实施：

简介： 信息：

ASTM D5453-08a 火焰点火发动机燃料柴油发动机燃料和发动机油通过紫外线荧光测定的总硫含量的标准试验方法
简介：
信息：ICS：75.100 CCS：发布：2008-02-01 实施：

简介： 信息：

ASTM D5453-08 火焰点火发动机燃料柴油发动机燃料和发动机油通过紫外线荧光测定的总硫含量的标准试验方法
简介：
信息：ICS：75.100 CCS：发布：2008-01-15 实施：

简介： 信息：

ASTM D5453-2008b
简介：Some process catalysts used in petroleum and chemical refining can be poisoned when trace amounts of sulfur bearing materials are contained in the feedstocks. This test method can be used to determine sulfur in process feeds sulfur in finished products, and can also be used for purposes of regulatory control.1.1 This test method covers the determination of total sulfur in liquid hydrocarbons, boiling in the range from approximately 25 to 400x00B0;C, with viscosities between approximately 0.2 and 20 cSt (mm2/S) at room temperature. 1.2 Three separate interlaboratory studies (ILS) on precision, and three other investigations that resulted in an ASTM research report, have determined that this test method is applicable to naphthas, distillates, engine oil, ethanol, Fatty Acid Methyl Ester (FAME), and engine fuel such as gasoline, oxygen enriched gasoline (ethanol blends, E-85, M-85, RFG), diesel, biodiesel, diesel/biodiesel blends, and jet fuel. Samples containing 1.0 to 8000 mg/kg total sulfur can be analyzed (Note 1). Note 18212;Estimates of the pooled limit of quantification (PLOQ) for the precision studies were calculated. Values ranged between less than 1.0 and less than 5.0 mg/kg (see Section 8 and 15.1). 1.3 This test method is applicable for total sulfur determination in liquid hydrocarbons containing less than 0.35 % (m/m) halogen(s). 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For warning statements, see 3.1, 6.3, 6.4, Section 7, and 8.1.
信息：ICS：75.100 (Lubricants, industrial oils and related pr CCS：发布：2008 实施：

简介： 信息：

ASTM D5453-2008a
简介：Some process catalysts used in petroleum and chemical refining can be poisoned when trace amounts of sulfur bearing materials are contained in the feedstocks. This test method can be used to determine sulfur in process feeds sulfur in finished products, and can also be used for purposes of regulatory control.1.1 This test method covers the determination of total sulfur in liquid hydrocarbons, boiling in the range from approximately 25 to 400x00B0;C, with viscosities between approximately 0.2 and 20 cSt (mm2/S) at room temperature. 1.2 Three separate interlaboratory studies (ILS) on precision, and three other investigations that resulted in an ASTM research report, have determined that this test method is applicable to naphthas, distillates, engine oil, ethanol, Fatty Acid Methyl Ester (FAME), and engine fuel such as gasoline, oxygen enriched gasoline (ethanol blends, E-85, M-85, RFG), diesel, biodiesel, diesel/biodiesel blends, and jet fuel. Samples containing 1.0 to 8000 mg/kg total sulfur can be analyzed (Note 1). Note 18212;Estimates of the pooled limit of quantification (PLOQ) for the precision studies were calculated. Values ranged between less than 1.0 and less than 5.0 mg/kg (see Section 8 and 15.1). 1.3 This test method is applicable for total sulfur determination in liquid hydrocarbons containing less than 0.35 % (m/m) halogen(s). 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For warning statements, see 3.1, 6.3, 6.4, Section 7, and 8.1.
信息：ICS：75.100 (Lubricants, industrial oils and related pr CCS：发布：2008 实施：

简介： 信息：

ASTM D5453-2008
简介：Some process catalysts used in petroleum and chemical refining can be poisoned when trace amounts of sulfur bearing materials are contained in the feedstocks. This test method can be used to determine sulfur in process feeds sulfur in finished products, and can also be used for purposes of regulatory control.1.1 This test method covers the determination of total sulfur in liquid hydrocarbons, boiling in the range from approximately 25 to 400x00B0;C, with viscosities between approximately 0.2 and 20 cSt (mm2/S) at room temperature. 1.2 Three separate interlaboratory studies (ILS) on precision, and two other investigations that resulted in an ASTM research report, have determined that this test method is applicable to naphthas, distillates, engine oil, ethanol, Fatty Acid Methyl Ester (FAME), and engine fuel such as gasoline, oxygen enriched gasoline (M-85, RFG), diesel, biodiesel, and jet fuel. Samples containing 1.0 to 8000 mg/kg total sulfur can be analyzed (Note 1). Note 18212;Estimates of the pooled limit of quantification (PLOQ) for each of the five precision studies were calculated. Values ranged between less than 1.0 and less than 5.0 mg/kg (see Section 8 and 15.1). 1.3 This test method is applicable for total sulfur determination in liquid hydrocarbons containing less than 0.35 % (m/m) halogen(s). 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For warning statements, see 3.1, 6.3, 6.4, Section 7, and 8.1.
信息：ICS：75.100 (Lubricants, industrial oils and related pr CCS：发布：2008 实施：

简介： 信息：

ASTM D5453-06 火焰点火发动机燃料柴油发动机燃料和发动机油通过紫外线荧光测定的总硫含量的标准试验方法
简介：
信息：ICS：75.100 CCS：发布：2006-05-01 实施：

简介： 信息：

ASTM D5453-2006 紫外线荧光测量法测定轻质烃、火花点燃式发动机燃料、柴油发动机油和发动机油中总硫量的标准试验方法
简介：Some process catalysts used in petroleum and chemical refining can be poisoned when trace amounts of sulfur bearing materials are contained in the feedstocks. This test method can be used to determine sulfur in process feeds sulfur in finished products, and can also be used for purposes of regulatory control.1.1 This test method covers the determination of total sulfur in liquid hydrocarbons, boiling in the range from approximately 25 to 400176;C, with viscosities between approximately 0.2 and 20 cSt (mm 2/S) at room temperature. 1.2 Three separate interlaboratory studies (ILS) on precision, and two other investigations that resulted in an ASTM research report, have determined that this test method is applicable to naphthas, distillates, engine oil, ethanol, Fatty Acid Methyl Ester (FAME), and engine fuel such as gasoline, oxygen enriched gasoline (M-85, RFG), diesel, biodiesel, and jet fuel. Samples containing 1.0 to 8000 mg/kg total sulfur can be analyzed (Note 1).Note 1Estimates of the pooled limit of quantification (PLOQ) for each of the five precision studies were calculated. Values ranged between less than 1.0 and less than 5.0 mg/kg (see Section and ).1.3 This test method is applicable for total sulfur determination in liquid hydrocarbons containing less than 0.35 % (m/m) halogen(s).1.4 The values stated in SI units are to be regarded as standard. No other units are included in this standard.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For warning statements, see 3.1, 6.3, 6.4 Section 7, and 8.1.
信息：ICS：75.100 (Lubricants, industrial oils and related pr CCS：E31 发布：2006 实施：

简介： 信息：

ASTM D5453-05 用紫外线荧光法测定汽车燃料和油中轻烃中总硫的标准试验方法
简介：
信息：ICS：75.100 CCS：发布：2005-05-01 实施：

简介： 信息：

ASTM D5453-2005 用紫外荧光法测定轻质烃、发动机燃料和机油中总硫含量的标准试验方法
简介：1.1 This test method covers the determination of total sulfur in liquid hydrocarbons, boiling in the range from approximately 25 to 400176;C, with viscosities between approximately 0.2 and 20 cSt (mm178;/S) at room temperature. 1.2 Three separate interlaboratory studies (ILS) on precision, and two other investigations that resulted in an ASTM research report, have determined that this test method is applicable to naphthas, distillates, oils, ethanol, Fatty Acid Methyl Ester (FAME), and motor fuels; such as gasoline, oxygen enriched gasoline (M-85, RFG), diesel, biodiesel and jet fuel. Samples containing 1.0 to 8000 mg/kg total sulfur can be analyzed (Note 1).Note 18212;Estimates of the pooled limit of quantification (PLOQ) for each of the three precision studies were calculated. Values ranged between less than 1.0 and less than 5.0 mg/kg (see Section 8 and 14.1).1.3 This test method is applicable for total sulfur determination in liquid hydrocarbons containing less than 0.35 % (m/m) halogen(s).1.4 The values stated in SI units are to be regarded as standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See 3.1, 6.3, 6.4, Section 7, and 8.1.
信息：ICS：75.100 (Lubricants, industrial oils and related pr CCS：E31;E34 发布：2005 实施：

简介： 信息：